| Age | Commit message (Collapse) | Author |
|---|
|
in SDIO node
The WiFi firmware requires that the power is kept enabled while in
suspend mode. Add the keep-power-in-suspend property in the SDIO node
to specify that the power must be kept when entering in a system wide
suspend state.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This fixes the following DT schemas check errors:
meson-gxbb-odroidc2.dt.yaml: gpio-regulator-tf_io: states:0: Additional items are not allowed (1800000, 1 were unexpected)
meson-gxbb-odroidc2.dt.yaml: gpio-regulator-tf_io: states:0: [3300000, 0, 1800000, 1] is too long
meson-gxbb-nexbox-a95x.dt.yaml: gpio-regulator: states:0: Additional items are not allowed (3300000, 1 were unexpected)
meson-gxbb-nexbox-a95x.dt.yaml: gpio-regulator: states:0: [1800000, 0, 3300000, 1] is too long
meson-gxbb-p200.dt.yaml: gpio-regulator: states:0: Additional items are not allowed (3300000, 1 were unexpected)
meson-gxbb-p200.dt.yaml: gpio-regulator: states:0: [1800000, 0, 3300000, 1] is too long
meson-gxl-s905x-hwacom-amazetv.dt.yaml: gpio-regulator: states:0: Additional items are not allowed (3300000, 1 were unexpected)
meson-gxl-s905x-hwacom-amazetv.dt.yaml: gpio-regulator: states:0: [1800000, 0, 3300000, 1] is too long
meson-gxbb-p201.dt.yaml: gpio-regulator: states:0: Additional items are not allowed (3300000, 1 were unexpected)
meson-gxbb-p201.dt.yaml: gpio-regulator: states:0: [1800000, 0, 3300000, 1] is too long
meson-g12b-odroid-n2.dt.yaml: gpio-regulator-tf_io: states:0: Additional items are not allowed (1800000, 1 were unexpected)
meson-g12b-odroid-n2.dt.yaml: gpio-regulator-tf_io: states:0: [3300000, 0, 1800000, 1] is too long
meson-gxl-s905x-nexbox-a95x.dt.yaml: gpio-regulator: states:0: Additional items are not allowed (3300000, 1 were unexpected)
meson-gxl-s905x-nexbox-a95x.dt.yaml: gpio-regulator: states:0: [1800000, 0, 3300000, 1] is too long
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
According the datasheets, emmc v2 chips (gxbb and gxl) don't support
more that 100Mhz in UHS-1 SD modes and HS in SDIO.
Align the max-frequency to 100MHz for UHS-1 and 50MHz for HS
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Commit 89a5e15bcba8 ("gpio/mmc/of: Respect polarity in the device tree")
changed the behavior of "cd-inverted" to follow the device tree bindings
specification:
According to SDHCI standard, CD lines are specified as "active low".
Using the "cd-inverted" property means that the CD line is "active high".
Fix the SD card description for meson by setting the cd-gpios as
"active low", according to the boards specifications, and dropping the
"cd-inverted" property.
Fixes: 89a5e15bcba8 ("gpio/mmc/of: Respect polarity in the device tree")
Signed-off-by: Loys Ollivier <lollivier@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The Nexbox A95X provides two USB ports. Enable the SoC's USB controller
on this board to make these USB ports usable.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Move the SPDX-License-Identifier lines to the top and drop the
license splat.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Extend configuring the MAC address from u-boot to all meson boards.
I didn't test this changeset but having checked libretech's u-boot
tree I believe it should just work.
Signed-off-by: Jorge Ramirez-Ortiz <jramirez@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Since the Data Strobe pin is optional, take it out of the default
eMMC pins and add a separate entry.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add the pinctrl to switch mmc clk pins in gpio (pulled down) mode. This
is necessary to be able to gate the clk outside of the SoC while
keeping it running in the controller
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
It does not make much sense to define cap-sd-highspeed in the emmc nodes
Just remove it.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This patch adds the AO CEC node in all the HDMI enabled boards DTS.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Sort nodes referenced by label alphabetically.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add HDMI output and connector nodes.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Since the GXL family has S905X and S905D SoCs, we're keeping the SoC
name in the DTS filename for clarity. Rename this file accordingly to
be consistent with the rest of the GXL DTS files.
Cc: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
