| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX arm64 device tree update for 5.4:
- New board support: i.MX8MQ Nitrogen8m, Hummingboard Pulse,
PICO-PI-IMX8M, i.MX8QXP AI_ML, and LS1046A FRWY board.
- Add gpio-ranges for GPIO devices on i.MX8MQ and i.MX8MM.
- Update OPP table according to latest data sheet and add opp-suspend
to OPP table for i.MX8MQ and i.MX8MM.
- Add IDEL states for i.MX8MM SoC.
- Correct I2C clock divider for Layerscape SoCs.
- Add series alias and LPUART baud clock for i.MX8QXP SoC.
- Add MIPI D-PHY device for i.MX8MQ and enable it on imx8mq-librem5
board.
- Enable USB1 and Type-C support for i.MX8MM EVK board.
- Add Thermal Monitor Unit support for LS1028A SoC.
- Misc small update and correction on Layerscape and i.MX8 support.
* tag 'imx-dt64-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (41 commits)
arm64: dts: imx8mq: Add mux controller to iomuxc_gpr
arm64: dts: fsl: add support for Hummingboard Pulse
arm64: dts: ls1088a: update gpio compatible
arm64: dts: imx: Add i.mx8mq nitrogen8m basic dts support
arm64: dts: ls1088a-qds: Add the spi-flash nodes under the DSPI controller
arm64: dts: ls1088a: Add the DSPI controller node
arm64: dts: imx8mm: Enable cpu-idle driver
arm64: dts: ls1028a: Add esdhc node in dts
arm64: dts: ls1028a: Add properties node for Display output pixel clock
arm64: dts: lx2160a: Fix incorrect I2C clock divider
arm64: dts: ls1028a: Fix incorrect I2C clock divider
arm64: dts: ls1012a: Fix incorrect I2C clock divider
arm64: dts: ls1088a: Fix incorrect I2C clock divider
arm64: dts: ls1028a: fix gpio nodes
arm64: dts: ls1028a: Add Thermal Monitor Unit node
arm64: dts: imx8mq-evk: Unbypass audio_pll1
arm64: dts: imx8mm: Add opp-suspend property to OPP table
arm64: dts: imx8mq: Add opp-suspend property to OPP table
arm64: dts: ls1088a: Revise gpio registers to little-endian
arm64: dts: add the console node for DPAA2 platforms
...
Link: https://lore.kernel.org/r/20190825153237.28829-6-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The SolidRun Hummingboard Pulse carrier board carries the SolidRun
i.MX8MQ based SOM.
Notably missing is PCIe support that depends on analog PLLOUT clock.
Current imx clk driver does not support this clock.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add basic dts support for i.MX8MQ NITROGEN8M.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
[Dafna: porting vendor's code to mainline]
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This patch adds basic i.MM8MN DDR4 EVK board support.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
TechNexion PICO-PI-IMX8M-DEV evaluation and development kit based on
NXP i.MX8M Quad applications processor. Datasheet can be found at:
https://s3.us-east-2.amazonaws.com/technexion/datasheets/picopiimx8m.pdf
The current level of support yields a working console and is able to boot
userspace from NFS or init ramdisk.
Additional subsystems that are active :
- Ethernet
- USB
Cc: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Richard Hu <richard.hu@technexion.com>
Signed-off-by: Andra Danciu <andradanciu1997@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for i.MX8QXP AI_ML board from Einfochips. This board is one
of the Consumer Edition boards of the 96Boards family based on i.MX8QXP
SoC from NXP/Freescale.
The initial support includes following peripherals which are tested and
known to be working:
1. Debug serial via UART2
2. uSD
3. WiFi
4. Ethernet
More information about this board can be found in Arrow website:
https://www.arrow.com/en/products/imx8-ai-ml/arrow-development-tools
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
ls1046afrwy board is based on nxp ls1046a SoC.
Board support's 4GB ddr memory, i2c, microSD card,
serial console,qspi nor flash,ifc nand flash,qsgmii network interface,
usb 3.0 and serdes interface to support two x1gen3 pcie interface.
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Signed-off-by: Pramod Kumar <pramod.kumar_1@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This is for the development kit board for the Librem 5. The current level
of support yields a working console and is able to boot userspace from
the network or eMMC.
Additional subsystems that are active :
- Both USB ports
- SD card socket
- WiFi usdhc
- WWAN modem
- GNSS
- GPIO keys
- LEDs
- gyro
- magnetometer
- touchscreen
- pwm
- backlight
- haptic motor
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Zii Ultra design, also known as RDU3, is the i.MX8M based successor
to the the i.MX6 based RDU2. This adds the basic board support for all
components which are supported by the upstream kernel at this time.
The board comes in 2 different versions, called RMB3 and Zest, which
are derived from the same design, but have different layouts and a
few small differences in the populated components.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add basic dts support for i.MM8MM LPDDR4 EVK.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add devicetree support for Oxalis SoM board from EBS-SYSTART. This
board is one of the 96Boards Enterprise Edition platform. Below are some
of the key features of this board:
* SoC: NXP Layerscape LS1012A
* RAM: 1GB DDR3L
* PMU: NXP VR5100
* Storage: 64MByte SPI Flash for bootloader and RCW, MicroSD Card, SATA
* Connectivity: 2x Ethernet
* USB: 2x USB3.0
More information about this board can be found in 96Boards product
page: https://www.96boards.org/product/oxalis/
Ethernet and SPI flash are not supported yet!
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
i.MX 8QuadXPlus is a quad (4x) Cortex-A35 proccessor with powerful
graphic and multimedia features. This patch adds imx8qxp mek board
support.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This is the evaluation kit board for the i.MX8M. The current level of
support yields a working console and is able to boot userspace from
SD card or Network.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> (v1)
Reviewed-by: Rob Herring <robh@kernel.org> (v3)
Tested-by: Tested-by: Baruch Siach <baruch@tkos.co.il> (v1)
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
LS1028A contains two ARM v8 CortexA72 processor cores
with 32 KB L1-D cache and 48 KB L1-I cache
Features summary
Two 32-bit / 64-bit ARM v8 Cortex-A72 CPUs
- Arranged as single clusters of two cores sharing a 1 MB L2 cache
- Speed Up to 1.3 GHz
- Support for cluster power-gating.
Cache coherent interconnect (CCI-400)
- Hardware-managed data coherency
- Up to 400 MHz
32-bit DDR4 SDRAM memory controller with ECC
Two PCIe 3.0 controllers
One serial ATA (SATA 3.0) controller
Two high-speed USB 3.0 controllers with integrated PHY
Following levels of DTSI/DTS files have been created for the LS1028A
SoC family:
- fsl-ls1028a.dtsi:
DTS-Include file for NXP LS1028A SoC.
- fsl-ls1028a-qds.dts:
DTS file for NXP LS1028A QDS board.
- fsl-ls1028a-rdb.dts:
DTS file for NXP LS1028A RDB board
Signed-off-by: Sudhanshu Gupta <sudhanshu.gupta@nxp.com>
Signed-off-by: Rai Harninder <harninder.rai@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
LS1012A-FRWY is an ls1012a based SoC board.
Key features of this board are Micro SD, USB 3.0,
upto 1GB DDR, UART
Signed-off-by: Pramod Kumar <pramod.kumar_1@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The LX2160A QorIQ Development System (QDS) is a test, evaluation, and
development platform, supporting QorIQ LX2160A processor.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
LX2160A reference design board (RDB) is a high-performance
computing, evaluation, and development platform with LX2160A
SoC.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Signed-off-by: Horia Geanta <horia.geanta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Zhang Ying-22455 <ying.zhang22455@nxp.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
"A bigger diffstat than usual with the kbuild changes and a tree wide
fix in the binding documentation.
Summary:
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing
memory leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node.
The prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to
dtb compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage
Technology, shimafuji, Tecon Microprocessor Technologies, DH
electronics GmbH, Opal Kelly, and Next Thing"
* tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (55 commits)
dt-bindings: usb: add #phy-cells to usb-nop-xceiv
dt-bindings: Remove leading zeros from bindings notation
kbuild: handle dtb-y and CONFIG_OF_ALL_DTBS natively in Makefile.lib
MIPS: dts: remove bogus bcm96358nb4ser.dtb from dtb-y entry
kbuild: clean up *.dtb and *.dtb.S patterns from top-level Makefile
.gitignore: move *.dtb and *.dtb.S patterns to the top-level .gitignore
.gitignore: sort normal pattern rules alphabetically
dt-bindings: add vendor prefix for Next Thing Co.
scripts/dtc: Update to upstream version v1.4.5-6-gc1e55a5513e9
of: dynamic: fix memory leak related to properties of __of_node_dup
of: overlay: make pr_err() string unique
of: overlay: pr_err from return NOTIFY_OK to overlay apply/remove
of: overlay: remove unneeded check for NULL kbasename()
of: overlay: remove a dependency on device node full_name
of: overlay: simplify applying symbols from an overlay
of: overlay: avoid race condition between applying multiple overlays
of: overlay: loosen overly strict phandle clash check
of: overlay: expand check of whether overlay changeset can be removed
of: overlay: detect cases where device tree may become corrupt
of: overlay: minor restructuring
...
|
|
If CONFIG_OF_ALL_DTBS is enabled, "make ARCH=arm64 dtbs" compiles each
DTB twice; one from arch/arm64/boot/dts/*/Makefile and the other from
the dtb-$(CONFIG_OF_ALL_DTBS) line in arch/arm64/boot/dts/Makefile.
It could be a race problem when building DTBS in parallel.
Another minor issue is CONFIG_OF_ALL_DTBS covers only *.dts in vendor
sub-directories, so this broke when Broadcom added one more hierarchy
in arch/arm64/boot/dts/broadcom/<soc>/.
One idea to fix the issues in a clean way is to move DTB handling
to Kbuild core scripts. Makefile.dtbinst already recognizes dtb-y
natively, so it should not hurt to do so.
Add $(dtb-y) to extra-y, and $(dtb-) as well if CONFIG_OF_ALL_DTBS is
enabled. All clutter things in Makefiles go away.
As a bonus clean-up, I also removed dts-dirs. Just use subdir-y
directly to traverse sub-directories.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
[robh: corrected BUILTIN_DTB to CONFIG_BUILTIN_DTB]
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
We need to add "clean-files" in Makfiles to clean up DT blobs, but we
often miss to do so.
Since there are no source files that end with .dtb or .dtb.S, so we
can clean-up those files from the top-level Makefile.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
LS1088A contains eight ARM v8 CortexA53 processor cores
with 32 KB L1-D cache and 32 KB L1-I cache
Features summary
Eight 32-bit / 64-bit ARM v8 Cortex-A53 CPUs
- Arranged as two clusters of four cores sharing a 1 MB L2 cache
- Speed Up to 1.5 GHz
- Support for cluster power-gating.
Cache coherent interconnect (CCI-400)
- Hardware-managed data coherency
- Up to 700 MHz
One 64-bit DDR4 SDRAM memory controller with ECC
Data path acceleration architecture 2.0 (DPAA2)
Three PCIe 3.0 controllers
One serial ATA (SATA 3.0) controller
Three high-speed USB 3.0 controllers with integrated PHY
Following levels of DTSI/DTS files have been created for the LS1088A
SoC family:
- fsl-ls1088a.dtsi:
DTS-Include file for NXP LS1088A SoC.
- fsl-ls1088a-qds.dts:
DTS file for NXP LS1088A QDS board.
- fsl-ls1088a-rdb.dts:
DTS file for NXP LS1088A RDB board
Signed-off-by: Harninder Rai <harninder.rai@nxp.com>
Signed-off-by: Ashish Kumar <ashish.kumar@nxp.com>
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>`
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This patch adds the device tree support for FSL LS2088A SoC based on
ARMv8 architecture.
Following levels of DTSI/DTS files have been created for the LS2088A
SoC family:
- fsl-ls2088a.dtsi:
DTS-Include file for FSL LS2088A SoC.
- fsl-ls2088a-qds.dts:
DTS file for FSL LS2088A QDS board.
- fsl-ls2088a-rdb.dts:
DTS file for FSL LS2088A RDB board.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Ashish Kumar <ashish.kumar@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
LS1012A features an advanced 64-bit ARM v8 CortexA53 processor
with 32 KB of parity protected L1-I cache, 32 KB of ECC protected
L1-D cache, as well as 256 KB of ECC protected L2 cache.
Features summary
One 64-bit ARM-v8 Cortex-A53 core with the following capabilities
- Arranged as a cluster of one core supporting a 256 KB L2 cache with ECC
protection
- Speed up to 800 MHz
- Parity-protected 32 KB L1 instruction cache and 32 KB L1 data cache
- Neon SIMD engine
- ARM v8 cryptography extensions
One 16-bit DDR3L SDRAM memory controller
ARM core-link CCI-400 cache coherent interconnect
Cryptography acceleration (SEC)
One Configurable x3 SerDes
One PCI Express Gen2 controller, supporting x1 operation
One serial ATA (SATA Gen 3.0) controller
One USB 3.0/2.0 controller with integrated PHY
Following levels of DTSI/DTS files have been created for the LS1012A
SoC family:
- fsl-ls1012a.dtsi:
DTS-Include file for FSL LS1012A SoC.
- fsl-ls1012a-frdm.dts:
DTS file for FSL LS1012A FRDM board.
- fsl-ls1012a-qds.dts:
DTS file for FSL LS1012A QDS board.
- fsl-ls1012a-rdb.dts:
DTS file for FSL LS1012A RDB board.
Signed-off-by: Harninder Rai <harninder.rai@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The LS1046A QorIQ development system (QDS) board is a high-performance
computing, evaluation, development, and test platform supporting the
LS1046A SoC.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The LS1046A reference design board (RDB) is a high-performance computing,
evaluation, and development platform that supports the LS1046A SoC.
Signed-off-by: Mingkai Hu <Mingkai.Hu@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The LS1043a-QDS board is a high-performance computing, evaluation,
development, and test platform supporting the LS1043a SoC.
shawn.guo: sort the entries in Makefile alphabetcially
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Wenbin Song <Wenbin.Song@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This patch adds build support for LS2080a QDS & RDB board DTS files
in the arm64 DTS Makefile.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Freescale is renaming the LS2085A SoC to LS2080A. This patch
addresses the same.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Freescale will be a spinning-out a set of ARMv8 based SoCs which
will be based on a similar overall SoC architecture. So, this patch
converts the existing infrastructure in the arm64/dts, arm64/Kconfig
and arm64/configs to use the generic convention ARCH_LAYERSCAPE
in place of the more specific FSL_LS2085A, to save code duplication
later-on.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This patch adds the device tree support for FSL LS2085A SoC
based on ARMv8 architecture.
Following levels of DTSI/DTS files have been created for the
LS2085A SoC family:
- fsl-ls2085a.dtsi:
DTS-Include file for FSL LS2085A SoC.
- fsl-ls2085a-simu.dts:
DTS file for FSL LS2085a software simulator model.
In addition, this patch adds build support for FSL's LS2085A
simulator model in arm64 dts Makefile.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Arnab Basu <arnab_basu@rocketmail.com>
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
