| Age | Commit message (Collapse) | Author |
|---|
|
net10 is connected to an SFP module. Unfortunately, the I2C lines are
not connected due to an address conflict. Now that DPAA uses phylink, we
can use in-band-status. This lets us determine whether the link is up or
down instead of assuming it is up all the time. Also fix the phy mode
while we're here.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
ls1046afrwy and ls1046ardb boards have CAT24C04[1] and CAT24C05[2]
eeproms respectively. Both are 4Kb (512 bytes) in size,
and compatible with AT24C04[3].
Remove multi-address entries, as both the boards have a single chip each.
[1] https://www.onsemi.com/pdf/datasheet/cat24c01-d.pdf
[2] https://www.onsemi.com/pdf/datasheet/cat24c03-d.pdf
[3] https://ww1.microchip.com/downloads/en/DeviceDoc/doc0180.pdf
Signed-off-by: Raag Jadav <raagjadav@gmail.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add interrupt line for RTC node, which is low level active.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The correct setting for the RGMII ports on LS1046ARDB is to
enable delay on both Rx and Tx so the interface mode used must
be PHY_INTERFACE_MODE_RGMII_ID.
Since commit 1b3047b5208a80 ("net: phy: realtek: add support for
configuring the RX delay on RTL8211F") the Realtek 8211F PHY driver
has control over the RGMII RX delay and it is disabling it for
RGMII_TXID. The LS1046ARDB uses two such PHYs in RGMII_ID mode but
in the device tree the mode was described as "rgmii".
Changing the phy-connection-type to "rgmii-id" to address the issue.
Fixes: 3fa395d2c48a ("arm64: dts: add LS1046A DPAA FMan nodes")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update the compatibles to use jedec,spi-nor.
Also update the max-frequency to 50MHz and spi-tx-bus-width to 1.
Align the QSPI node with other similar boards like(ls1088ardb,
ls1046afrwy) as per bindings.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
layerscape otg function should be supported HNP SRP and ADP protocol
accroing to rm doc, but dwc3 code not realize it and use id pin to
detect who is host or device(0 is host 1 is device) this patch is to
enable OTG mode on ls1028ardb ls1088ardb and ls1046ardb in dts
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Use a generic node name for the m25p80 flashes on ls1043 and ls1046 boards.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
We will move the FSL QSPI driver to the SPI framework soon. To
prepare and to make sure the full buswidth is used (as it is with
the current driver), let's add the right properties.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The properties 'num-cs' and 'bus-num' were never read by the driver
and can be removed.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
dtc has new checks for I2C and SPI buses. Fix the SPI bus node names
and warnings in unit-addresses.
arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dtb: Warning (i2c_bus_reg): /soc/i2c@2180000/eeprom@57: I2C bus unit address format error, expected "53"
arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dtb: Warning (i2c_bus_reg): /soc/i2c@2180000/eeprom@56: I2C bus unit address format error, expected "52"
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Replace license text with corresponding SPDX identifiers and update the
format of existing SPDX identifiers to follow the new guideline
Documentation/process/license-rules.rst.
Note that some of the files mentioned X11 license previously but the
license text actually matches MIT license.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add the DPAA 1.x FMan device tree nodes for LS1046A boards.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This patch is to enable SD UHS-I mode and eMMC HS200 mode on
LS1046ARDB in dts. Also, the eSDHC peripheral clock must be used
instead of platform clock to support these modes.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Update the copyright claims to comply with company policy.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The LS1046A reference design board (RDB) is a high-performance computing,
evaluation, and development platform that supports the LS1046A SoC.
Signed-off-by: Mingkai Hu <Mingkai.Hu@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
