| Age | Commit message (Collapse) | Author |
|---|
|
nxp,fspi-dll-slvdly is not documented nor used anywhere.
Drop this invalid property.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
'pinctrl-assert-gpios' is not a valid property.
Remove it to fix the following schema warning:
imx8dxl-evk.dtb: spi@5a030000: Unevaluated properties are not allowed ('pinctrl-assert-gpios' was unexpected)
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The 'fsl,spi-num-chipselects' property is not a valid one, so remove it.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Pull ARM SoC devicetree updates from Arnd Bergmann:
"The devicetree changes overall are again dominated by the Qualcomm
Snapdragon platform that weighs in at over 300 changesets, but there
are many updates across other platforms as well, notably Mediatek,
NXP, Rockchips, Renesas, TI, Samsung and ST Microelectronics. These
all add new features for existing machines, as well as new machines
and SoCs.
The newly added SoCs are:
- Allwinner T113-s, an Cortex-A7 based variant of the RISC-V based D1
chip.
- StarFive JH7110, a RISC-V SoC based on the Sifive U74 core like its
JH7100 predecessor, but with additional CPU cores and a GPU.
- Apple M2 as used in current Macbook Air/Pro and Mac Mini gets
added, with comparable support as its M1 predecessor.
- Unisoc UMS512 (Tiger T610) is a midrange smartphone SoC
- Qualcomm IPQ5332 and IPQ9574 are Wi-Fi 7 networking SoCs, based on
the Cortex-A53 and Cortex-A73 cores, respectively.
- Qualcomm sa8775p is an automotive SoC derived from the Snapdragon
family.
Including the initial board support for the added SoC platforms, there
are 52 new machines. The largest group are 19 boards industrial
embedded boards based on the NXP i.MX6 (32-bit) and i.MX8 (64-bit)
families.
Others include:
- Two boards based on the Allwinner f1c200s ultra-low-cost chip
- Three 'Banana Pi' variants based on the Amlogic g12b (A311D, S922X)
SoC.
- The Gl.Inet mv1000 router based on Marvell Armada 3720
- A Wifi/LTE Dongle based on Qualcomm msm8916
- Two robotics boards based on Qualcomm QRB chips
- Three Snapdragon based phones made by Xiaomi
- Five developments boards based on various Rockchip SoCs, including
the rk3588s-khadas-edge2 and a few NanoPi models
- The AM625 Beagleplay industrial SBC
Another 14 machines get removed: both boards for the obsolete 'oxnas'
platform, three boards for the Renesas r8a77950 SoC that were only for
pre-production chips, and various chromebook models based on the
Qualcomm Sc7180 'trogdor' design that were never part of products"
* tag 'soc-dt-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (836 commits)
arm64: dts: rockchip: Add support for volume keys to rk3399-pinephone-pro
arm64: dts: rockchip: Add vdd_cpu_big regulators to rk3588-rock-5b
arm64: dts: rockchip: Use generic name for es8316 on Pinebook Pro and Rock 5B
arm64: dts: rockchip: Drop RTC clock-frequency on rk3588-rock-5b
arm64: dts: apple: t8112: Add PWM controller
arm64: dts: apple: t600x: Add PWM controller
arm64: dts: apple: t8103: Add PWM controller
arm64: dts: rockchip: Add pinctrl gpio-ranges for rk356x
ARM: dts: nomadik: Replace deprecated spi-gpio properties
ARM: dts: aspeed-g6: Add UDMA node
ARM: dts: aspeed: greatlakes: add mctp device
ARM: dts: aspeed: greatlakes: Add gpio names
ARM: dts: aspeed: p10bmc: Change power supply info
arm64: dts: mediatek: mt6795-xperia-m5: Add Bosch BMM050 Magnetometer
arm64: dts: mediatek: mt6795-xperia-m5: Add Bosch BMA255 Accelerometer
arm64: dts: mediatek: mt6795: Add tertiary PWM node
arm64: dts: rockchip: add panel to Anbernic RG353 series
dt-bindings: arm: Add Data Modul i.MX8M Plus eDM SBC
dt-bindings: arm: fsl: Add chargebyte Tarragon
dt-bindings: vendor-prefixes: add chargebyte
...
|
|
Bindings expect thermal node names to end with '-thermal':
imx8qxp-mek.dtb: thermal-zones: 'pmic-thermal0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-]{1,12}-thermal$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The deprecated property is named snps,reset-gpio, but this devicetree
used snps,reset-gpios instead which results in the reset not being used
and the following make dtbs_check error:
./arch/arm64/boot/dts/freescale/imx8dxl-evk.dtb: ethernet@5b050000: 'snps,reset-gpio' is a dependency of 'snps,reset-delays-us'
From schema: ./Documentation/devicetree/bindings/net/snps,dwmac.yaml
Use the preferred method of defining the reset gpio in the phy node
itself. Note that this drops the 10 us pre-delay, but prior this wasn't
used at all and a pre-delay doesn't make much sense in this context so
it should be fine.
Fixes: 8dd495d12374 ("arm64: dts: freescale: add support for i.MX8DXL EVK board")
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The hibernation mode of AR8031 PHY defaults to be enabled after hardware
reset. When the cable is unplugged, the PHY will enter hibernation mode
after about 10 senconds and the PHY clocks will be stopped to save
power. However, due to the design of EQOS, the mac needs the RX_CLK of
PHY for software reset to complete. Otherwise the software reset of EQOS
will be failed and do not work correctly. The only way is to disable
hibernation mode of AR8031 PHY for EQOS, the "qca,disable-hibernation-mode"
property is used for this purpose and has already been submitted to the
upstream, for more details please refer to the below link:
https://lore.kernel.org/netdev/20220818030054.1010660-2-wei.fang@nxp.com/
This issue is easy to reproduce, just unplug the cable and "ifconfig eth0
down", after about 10 senconds, then "ifconfig eth0 up", you will see
failure log on the serial port. The log is shown as following:
root@imx8dxlevk:~#
[34.941970] imx-dwmac 5b050000.ethernet eth0: Link is Down
root@imx8dxlevk:~# ifconfig eth0 down
[35.437814] imx-dwmac 5b050000.ethernet eth0: FPE workqueue stop
[35.507913] imx-dwmac 5b050000.ethernet eth0: PHY [stmmac-1:00] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL)
[35.518613] imx-dwmac 5b050000.ethernet eth0: configuring for phy/rgmii-id link mode
root@imx8dxlevk:~# ifconfig eth0 up
[71.143044] imx-dwmac 5b050000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[71.215855] imx-dwmac 5b050000.ethernet eth0: PHY [stmmac-1:00] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL)
[72.230417] imx-dwmac 5b050000.ethernet: Failed to reset the dma
[72.236512] imx-dwmac 5b050000.ethernet eth0: stmmac_hw_setup: DMA engine initialization failed
[72.245258] imx-dwmac 5b050000.ethernet eth0: __stmmac_open: Hw setup failed
SIOCSIFFLAGS: Connection timed out
After applying this patch, the software reset of EQOS will be
successful. And the log is shown as below.
root@imx8dxlevk:~# ifconfig eth0 up
[96.114344] imx-dwmac 5b050000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[96.171466] imx-dwmac 5b050000.ethernet eth0: PHY [stmmac-1:00] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL)
[96.188883] imx-dwmac 5b050000.ethernet eth0: No Safety Features support found
[96.196221] imx-dwmac 5b050000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[96.204846] imx-dwmac 5b050000.ethernet eth0: registered PTP clock
[96.225558] imx-dwmac 5b050000.ethernet eth0: FPE workqueue start
[96.236858] imx-dwmac 5b050000.ethernet eth0: configuring for phy/rgmii-id link mode
[96.249358] 8021q: adding VLAN 0 to HW filter on device eth0
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable lpspi0 at imx8dxl_evk boards dts.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable flexspi0 at imx8dxl_evk boards dts.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable adc0 at imx8dxl_evk boards dts.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The mii_select node is used to determine the fec1's interface
type. Using "enable-active-high" property to configure the
interface type as "RMII". Deleting the property as "RGMII".
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
There are two chipidea usb controller in 8dxl.
Add usb node at common connect subsystem.
Enable two usb at imx8dxl_evk boards dts.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This is to support the EVK (Evaluation Kit Board) for the i.MX8DXL.
The patch has enabled the serial console, SD/EMMC interface, and
the eqos and fec ethernet network.
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
