Age | Commit message (Collapse) | Author |
|
The default of 5ms is too low.
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This is needed for the 1LV Cyress WiFi module to probe correctly.
It also helps improve GNSS sensitivity.
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Some wifi cards need reset asserted until after the power supplies
have been enabled.
So wire up the W_DISABLE signal for the SDIO port (WIFI_REG_ON net) and
the BT_REG_ON net to use it for power sequencing.
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The redpine wifi card takes some time to wake up. Wait for it.
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Connect the wifi power regulator to the corresponding GPIO.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fix wrong pinctrl assignments.
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Suggested-by: Eric Kuzmenko <eric.kuzmenko@puri.sm>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add the missing description for the reset gpio to the panels DT
description.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
with dtschema
Align the name of operating-points node to dtschema to fix warnings like:
ddrc-opp-table: $nodename:0: 'ddrc-opp-table' does not match '^opp-table(-[a-z0-9]+)?$'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
There was an additional alias in the specifier it hogged line 27
instead of line 1.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
These sections should be read only as they contain important data.
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
IMX8MQ_AUDIO_PLL1 and IMX8MQ_AUDIO_PLL2 are setup to the same rates
right on the clock controller.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Expect all those regulators to be turned on initially.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This enables the Librem5's ft8006p based LCD panel driven by the
imx8mq's Northwest Logic DSI IP core and mxsfb display controller.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
It's a supply for to touch and LCD.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The tps65982 feeds the bq25895 charge controller on the Librem 5.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
With the pmic driver fixed we can now shut off the regulator in the gpc.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This is consistent with other IRQs and makes keeps currents low.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
According to commit e045f044e84e ("arm64: dts: imx8mq: Move usdhc clocks
assignment to board DT") add the clocks assignment to imx8mq-librem5.dtsi
too.
Fixes: e045f044e84e ("arm64: dts: imx8mq: Move usdhc clocks assignment to board DT")
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
In order for the touchscreen interrupt line to work, describe it properly.
Otherwise it can work if defaults are ok, but we cannot be sure.
Fixes: 8f0216b006e5 ("arm64: dts: Add a device tree for the Librem 5 phone")
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
buck7 is the supply here. Also, fix alphabetical ordering.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
dtschema expects GPIO hogs to end with 'hog' suffix.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Correct the name of property for GPIO specifier in GPIO hog.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW = 1 = IRQ_TYPE_EDGE_RISING
Correct the interrupt flags, assuming the author of the code wanted same
logical behavior behind the name "ACTIVE_xxx", this is:
ACTIVE_LOW => IRQ_TYPE_LEVEL_LOW
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-By: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The ti,tps6598x binding requires interrupt-names property. The driver
does not really use it but the hardware could have more interrupt lines
connected. This fixes dtbs_check warning:
arch/arm64/boot/dts/freescale/imx8mq-librem5-r2.dt.yaml: usb-pd@3f: 'interrupt-names' is a required property
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The 'interrupt-names' property is not described in dtschema, not used by
the driver and does not really make sense as its value is simple 'irq'.
Drop it to fix dtbs_check warnings like:
arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dt.yaml:
pmic@4b: 'interrupt-names' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Device tree schema expects regulator names to be lowercase. This fixes
dtbs_check warnings like:
pmic@4b: regulators:LDO1:regulator-name:0: 'LDO1' does not match '^ldo[1-7]$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add a devicetree description for the Librem 5 phone. 4 hardware revisions
have been available. Some revisions include changes that need different
software to be run. So far, r3 ("Dogwood") is one such example, see:
"Aspen" r0 not supported (very few devices exist)
"Birch" r1 supported by r2
"Chestnut" r2 added by this patch
"Dogwood" r3 added by this patch
"Evergreen" r4 tba / most likely supported by r3
See https://puri.sm/products/librem-5/ for more information.
This boots to a working console with working WWAN modem, wifi usdhc,
IMU sensor device, proximity sensor, haptic motor, gpio keys, GNSS and LEDs.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com> (for the audio part)
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|