| Age | Commit message (Collapse) | Author |
|---|
|
"simple-panel" compatible is not documented and nothing in Linux kernel
binds to it:
imx8mq-mnt-reform2.dtb: panel: compatible: ['innolux,n125hce-gn1', 'simple-panel'] is too long
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Move the PCIe clock-names property from various DTs into SoC dtsi to
reduce duplication. In case of a couple of boards, reorder the clock
so they match the order in yaml DT bindings.
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com> # imx8mq.dtsi, imx8mq-tqma8mq-mba8mx.dts
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Avoid the following checkpatch warning:
arch/arm/boot/dts/imx8mq-mnt-reform2.dts:213: check: Please don't use
multiple blank lines
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The i.MX8MQ has the same PWM IP as i.MX6 / i.MX7. This IP and the driver
supporting pwm polarity inversion. Switch CPU device tree fragment to
use 3 pwm-cells and correct board device trees.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The slew rate and drive-strength of the i2c3 pads were much too
high. Bring them down to avoid signal quality issues.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This adds support for the internal display of the Reform2 Laptop, which
is connected to the i.MX8MQ via a MIPI-DSI->eDP bridge chip. Clocking
is derived from a system PLL, which provides quite good rate matching
for the single supported display mode and keeps the video PLL free for
usage with the external display, which isn't supported yet.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
A new 'chassis-type' root node property has recently been approved for
the device-tree specification, in order to provide a simple way for
userspace to detect the device form factor and adjust their behavior
accordingly.
This patch fills in this property for end-user devices (such as laptops,
smartphones and tablets) based on NXP ARM64 processors.
Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The SD card slot on the Reform 2 uses the card detect pad routed to
the uSDHC2 module as intended. This is currently working as it is the
default mux setting for this pad, but better be explicit and add it
to the pinctrl node.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This adds sound support to the Reform2.
It differs from the downstream implementation in that the codec
is used as the BCLK and FSYNC master and the i.MX8MQ only supplies
a fixed 25MHz MCLK from the oscillator. This allows to support
a wider range of audio rates by using the codec PLL and to shut
down the audio PLLs on the i.MX8MQ SoC side.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This adds a basic devicetree for the MNT Reform2 DIY laptop. Not all
of the board periperals are enabled yet, as some of them still require
kernel patches to work properly. The nodes for those peripherals will
be added as soon as the required patches are upstream.
The following has been tested to work:
- UART console
- SD card
- eMMC
- Gigabit Ethernet
- USB (internal Keyboard, Mouse, external ports)
- M.2 PCIe port
Co-developed-by: Lukas F. Hartmann <lukas@mntre.com>
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
