| Age | Commit message (Collapse) | Author |
|---|
|
No functional changes.
Adjust to comply with dt-schema requirements
and make possible to validate values.
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW = 1 = IRQ_TYPE_EDGE_RISING
Correct the interrupt flags, assuming the author of the code wanted same
logical behavior behind the name "ACTIVE_xxx", this is:
ACTIVE_LOW => IRQ_TYPE_LEVEL_LOW
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-By: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Device tree schema expects pin configuration groups to end with 'grp'
suffix, otherwise dtbs_check complain with a warning like:
... do not match any of the regexes: 'grp$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Use preferred properties of phy node instead of deprecated
phy-reset-gpios (and others). This avoids copying deprecated code into
future DTSes.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
i.MX8MQ Phanbell board uses Realtek RTL8211FD as Ethernet PHY.
Its datasheet states that the proper post reset duration should be at least 50 ms.
Fixes: f34d4bfab354 ("arm64: dts: imx8mq-phanbell: Add support for ethernet")
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
It was based on Google Source Code for Coral Edge TPU Mendel release:
https://coral.googlesource.com/linux-imx/
It was tested on Coral Dev Board using this command:
sudo stress --cpu 4 --timeout 3600
Signed-off-by: Vitor Massaru Iha <vitor@massaru.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for ethernet on Google's i.MX 8MQ Phanbell
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Tested-by: Vitor Massaru Iha <vitor@massaru.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This patch adds the device tree to support Google Coral Edge TPU,
historicaly named as fsl-imx8mq-phanbell, a computer on module
which can be used for AI/ML propose.
It introduces a minimal enablement support for this module and
was totally based on the NXP i.MX 8MQ EVK board and i.MX 8MQ Phanbell
Google Source Code for Coral Edge TPU Mendel release:
https://coral.googlesource.com/linux-imx/
Tested components:
- PMIC;
- USB-C OTG;
- USB-C PWR;
- micro-USB;
- USB.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
