| Age | Commit message (Collapse) | Author |
|---|
|
This is the lowest frequency supported by older iMX8MQ SoC
revisions.
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
According to imx8mq errata (ERR007805):
> To meet the clock low period requirement in fast speed mode,
> SCL must be configured to 384KHz or less.
Note that the imx i2c driver already implements this erratum and works
around it. This is only for the description to reflect reality.
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
0.8V is outside of the operating voltage specified for imx8mq, see
chapter 3.1.4 "Operating ranges" of the IMX8MDQLQCEC document.
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This reduces power consumption in system suspend by about 10%.
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Based on tests with my left ear (which appears to require lower levels
than the right one), one Birch, one Dogwood and three Evergreens.
It seems that the sensor reacts very weakly to hair, so let's make
the thresholds rather generous to compensate.
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
RS9116 card already limits itself to 50MHz by being a high-speed card,
while AP6275S can work at 100MHz just fine (technically it should work
at 200MHz as well since it's a SDR104 card, but it doesn't appear to be
the case in practice and further research will be needed to find out why).
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Userland needs the mount matrix to know the correct orientation of
the part.
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
They're still in the operating range according to i.MX 8M Quad
datasheet. There's some headroom added over minimal values to
account for voltage drop.
Operational ranges (min - typ - max [selected]):
- VDD_SOC (BUCK1): 0.81 - 0.9 - 0.99 [0.88]
- VDD_ARM (BUCK2): 0.81 - 0.9 - 1.05 [0.84] (1000MHz)
0.90 - 1.0 - 1.05 [0.93] (1500MHz)
- VDD_GPU (BUCK3): 0.81 - 0.9 - 1.05 [0.85] (800MHz)
0.90 - 1.0 - 1.05 [ -- ] (1000MHz)
- VDD_VPU (BUCK4): 0.81 - 0.9 - 1.05 [ -- ] (550/500/588MHz)
0.90 - 1.0 - 1.05 [0.93] (660/600/800MHz)
Idle power consumption doesn't appear to be influenced much,
but a simple load test (`cat /dev/urandom | pigz - > /dev/null`
combined with running Animatch) seems to show about 0.3W of
difference.
Care is advised, as there may be differences between each
units in how low can they be undervolted - in my experience,
reaching that point usually makes the phone fail to boot.
In my case, it appears that my Birch phone can go down the most.
This is a somewhat conservative set of values that I've seen
working well on all my devices; I haven't tried very hard to
optimize it, so more experiments are welcome.
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Correctly set regulation-voltage, termination-current and charge-current
for the different librem 5 board revisions.
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add brightness-levels and default-brightness-level properties to
the librem5 board description that have been used for a long time.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
No functional change, but it describes the hardware better.
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fix the regulator name for the audio-1v8 regulator.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The CLKO2 clock is used for both camera CSI interfaces as the
driving clock for the connected sensors. In order for it to be
available, use this hog. We can't simply add it to 2 different
sensor descriptions.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
No frames are streamed when using the default frequencies. I'm not yet
sure why the fastest ones don't work here but we've been using these
frequencies successfully for a long time now.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Bindings expect thermal node names to end with '-thermal':
imx8qxp-mek.dtb: thermal-zones: 'pmic-thermal0' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-]{1,12}-thermal$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
These buttons are capable of waking up a suspended system, add the
appropriate property for both.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
TPM1/TPM3 are missing, add them.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This adds support for the 4 USB3 host ports on the board, which are
connected to the i.MX8MP SoC via a Realtek RTS5411 hub.
As the schematic for the board is not available, I could not validate
that this really reflects the reality, but I modeled things after the
hacked in usage of the GPIOs in the downstream kernel.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add FlexSPI node for i.MX93.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Align the clock and reg properties order with example bindings
and the rest of the imx8mp.dtsi . No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This block should not be compatible with simple-bus and misuse it that way.
Instead, the driver should scan its subnodes and bind drivers to them.
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Liu Ying <victor.liu@nxp.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Fixes: 94e6197dadc9 ("arm64: dts: imx8mp: Add LCDIF2 & LDB nodes")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
UART ports have DMA capability. Describe the UART DMA properties.
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The i.MX8MP DHCOM SoM may come with either external RGMII PHY or
LAN8740Ai RMII PHY on the SoM attached to FEC MAC. Add pin mux
settings for both options, so that DT overlay can override these
settings on SoM variant with the LAN8740Ai PHY.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The i.MX8MP DHCOM SoM may come with either KSZ9131RNXI RGMII PHY
or LAN8740Ai RMII PHY on the SoM attached to EQoS MAC. Add pin
mux settings for both options, so that DT overlay can override
these settings on SoM variant with the LAN8740Ai PHY.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The current variant of the SoM has LAN8740Ai PHY connected to EQoS
strapped to MDIO address 0 , adjust the MDIO address to match the
hardware.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fix copy-paste error in the EQoS reset comment, align with SoM schematic.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The PHY nodes may be activated via DTO in case another SoM variant
is populated into the development kit. Do not delete the nodes.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
DHCOM and PDK2
The GPIO M SoM pin is connected to CLKOUT1, while CLKOUT2 is used as a supply
for TC9595 bridge chip clock. Update the comment. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
PDK2
Add PCIe support for DH electronics i.MX8M Plus DHCOM SoM on PDK2 carrier board.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The I2C4 bus is exposed on the camera connector. Add and select the
corresponding pinmux entries and set the default frequency. The device
is left disabled, to be enabled from camera overlays.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add i.MX8MP PCIe EP support.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add i.MX8MQ PCIe EP support.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add i.MX8MM PCIe EP support.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add the bbnsm node for RTC & ON/OFF button support
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Use the serdev feature to load the driver for the 88W8997 bluetooth
driver.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The GICv3 ITS is an MSI controller, therefore its node name should be
'msi-controller'.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Capitalise Yavia in comment and add missing whitespace.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add PCIe support on the Verdin iMX8M Plus.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The previous patch added the device tree to support Toradex Apalis
iMX8 [1] aka QuadMax a computer on module which can be used on
different carrier boards which this patch introduces.
The module consists of an NXP i.MX 8 family SoC (either i.MX 8QuadMax or
8QuadPlus), two PF8100 PMICs, a KSZ9131 Gigabit Ethernet PHY, 2, 4 or 8
GB of LPDDR4 RAM, an eMMC, an SGTL5000 analogue audio codec, an USB3503A
USB HSIC hub, an optional I2C EEPROM plus an optional Bluetooth/Wi-Fi
module.
Anything that is not self-contained on the module is disabled by
default.
The carrier board device trees contained in this patch include the
module's device tree and enable the supported peripherals of the
carrier board.
Some level of display functionality just landed upstream but requires
further integration/testing on our side. Therefore, currently only
basic console UART, eMMC and Ethernet functionality work fine.
As there is no i.MX 8QuadPlus device tree upstream those have been
dropped. However, apart from an error message during boot about it
failing to bring up the second Cortex-A72 core this boots fine on
QuadPlus' as well.
[1] https://www.toradex.com/computer-on-modules/apalis-arm-family/nxp-imx-8
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This patch adds the device tree to support Toradex Apalis iMX8 [1] aka
QuadMax a computer on module which can be used on different carrier
boards.
The module consists of an NXP i.MX 8 family SoC (either i.MX 8QuadMax or
8QuadPlus), two PF8100 PMICs, a KSZ9131 Gigabit Ethernet PHY, 2, 4 or 8
GB of LPDDR4 RAM, an eMMC, an SGTL5000 analogue audio codec, an USB3503A
USB HSIC hub, an optional I2C EEPROM plus an optional Bluetooth/Wi-Fi
module.
Anything that is not self-contained on the module is disabled by
default.
The carrier board device trees in the next patch will include the
module's device tree and enable the supported peripherals of the
carrier board.
Some level of display functionality just landed upstream but requires
further integration/testing on our side. Therefore, currently only
basic console UART, eMMC and Ethernet functionality work fine.
As there is no i.MX 8QuadPlus device tree upstream those have been
dropped. However, apart from an error message during boot about it
failing to bring up the second Cortex-A72 core this boots fine on
QuadPlus' as well.
[1] https://www.toradex.com/computer-on-modules/apalis-arm-family/nxp-imx-8
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable VPU decoder and encoder functionality.
Signed-off-by: Zhou Peng <eagle.zhou@nxp.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add CAN node for imx8qm in devicetree.
Unlike on the i.MX 8QXP where the flexcan clocks are shared between
multiple CAN instances, the i.MX 8QM has separate flexcan clock slices.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add FlexCAN decive in adma subsystem.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> # TQMa8XQP
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
60MHz is the maximum frequency mentioned in the datasheet for
master mode. Set that to 60MHz to match lpspi2.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This commit adds io-channel-cells property to the ADC nodes. This
property is required in order for an IIO consumer driver to work.
Especially required for Apalis iMX8 QM, as the touchscreen driver
uses ADC channels with the ADC driver based on IIO framework.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for lsio_pwm0-3.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- Add dedicated kmem_cache for typical/small skb->head, avoid having
to access struct page at kfree time, and improve memory use.
- Introduce sysctl to set default RPS configuration for new netdevs.
- Define Netlink protocol specification format which can be used to
describe messages used by each family and auto-generate parsers.
Add tools for generating kernel data structures and uAPI headers.
- Expose all net/core sysctls inside netns.
- Remove 4s sleep in netpoll if carrier is instantly detected on
boot.
- Add configurable limit of MDB entries per port, and port-vlan.
- Continue populating drop reasons throughout the stack.
- Retire a handful of legacy Qdiscs and classifiers.
Protocols:
- Support IPv4 big TCP (TSO frames larger than 64kB).
- Add IP_LOCAL_PORT_RANGE socket option, to control local port range
on socket by socket basis.
- Track and report in procfs number of MPTCP sockets used.
- Support mixing IPv4 and IPv6 flows in the in-kernel MPTCP path
manager.
- IPv6: don't check net.ipv6.route.max_size and rely on garbage
collection to free memory (similarly to IPv4).
- Support Penultimate Segment Pop (PSP) flavor in SRv6 (RFC8986).
- ICMP: add per-rate limit counters.
- Add support for user scanning requests in ieee802154.
- Remove static WEP support.
- Support minimal Wi-Fi 7 Extremely High Throughput (EHT) rate
reporting.
- WiFi 7 EHT channel puncturing support (client & AP).
BPF:
- Add a rbtree data structure following the "next-gen data structure"
precedent set by recently added linked list, that is, by using
kfunc + kptr instead of adding a new BPF map type.
- Expose XDP hints via kfuncs with initial support for RX hash and
timestamp metadata.
- Add BPF_F_NO_TUNNEL_KEY extension to bpf_skb_set_tunnel_key to
better support decap on GRE tunnel devices not operating in collect
metadata.
- Improve x86 JIT's codegen for PROBE_MEM runtime error checks.
- Remove the need for trace_printk_lock for bpf_trace_printk and
bpf_trace_vprintk helpers.
- Extend libbpf's bpf_tracing.h support for tracing arguments of
kprobes/uprobes and syscall as a special case.
- Significantly reduce the search time for module symbols by
livepatch and BPF.
- Enable cpumasks to be used as kptrs, which is useful for tracing
programs tracking which tasks end up running on which CPUs in
different time intervals.
- Add support for BPF trampoline on s390x and riscv64.
- Add capability to export the XDP features supported by the NIC.
- Add __bpf_kfunc tag for marking kernel functions as kfuncs.
- Add cgroup.memory=nobpf kernel parameter option to disable BPF
memory accounting for container environments.
Netfilter:
- Remove the CLUSTERIP target. It has been marked as obsolete for
years, and we still have WARN splats wrt races of the out-of-band
/proc interface installed by this target.
- Add 'destroy' commands to nf_tables. They are identical to the
existing 'delete' commands, but do not return an error if the
referenced object (set, chain, rule...) did not exist.
Driver API:
- Improve cpumask_local_spread() locality to help NICs set the right
IRQ affinity on AMD platforms.
- Separate C22 and C45 MDIO bus transactions more clearly.
- Introduce new DCB table to control DSCP rewrite on egress.
- Support configuration of Physical Layer Collision Avoidance (PLCA)
Reconciliation Sublayer (RS) (802.3cg-2019). Modern version of
shared medium Ethernet.
- Support for MAC Merge layer (IEEE 802.3-2018 clause 99). Allowing
preemption of low priority frames by high priority frames.
- Add support for controlling MACSec offload using netlink SET.
- Rework devlink instance refcounts to allow registration and
de-registration under the instance lock. Split the code into
multiple files, drop some of the unnecessarily granular locks and
factor out common parts of netlink operation handling.
- Add TX frame aggregation parameters (for USB drivers).
- Add a new attr TCA_EXT_WARN_MSG to report TC (offload) warning
messages with notifications for debug.
- Allow offloading of UDP NEW connections via act_ct.
- Add support for per action HW stats in TC.
- Support hardware miss to TC action (continue processing in SW from
a specific point in the action chain).
- Warn if old Wireless Extension user space interface is used with
modern cfg80211/mac80211 drivers. Do not support Wireless
Extensions for Wi-Fi 7 devices at all. Everyone should switch to
using nl80211 interface instead.
- Improve the CAN bit timing configuration. Use extack to return
error messages directly to user space, update the SJW handling,
including the definition of a new default value that will benefit
CAN-FD controllers, by increasing their oscillator tolerance.
New hardware / drivers:
- Ethernet:
- nVidia BlueField-3 support (control traffic driver)
- Ethernet support for imx93 SoCs
- Motorcomm yt8531 gigabit Ethernet PHY
- onsemi NCN26000 10BASE-T1S PHY (with support for PLCA)
- Microchip LAN8841 PHY (incl. cable diagnostics and PTP)
- Amlogic gxl MDIO mux
- WiFi:
- RealTek RTL8188EU (rtl8xxxu)
- Qualcomm Wi-Fi 7 devices (ath12k)
- CAN:
- Renesas R-Car V4H
Drivers:
- Bluetooth:
- Set Per Platform Antenna Gain (PPAG) for Intel controllers.
- Ethernet NICs:
- Intel (1G, igc):
- support TSN / Qbv / packet scheduling features of i226 model
- Intel (100G, ice):
- use GNSS subsystem instead of TTY
- multi-buffer XDP support
- extend support for GPIO pins to E823 devices
- nVidia/Mellanox:
- update the shared buffer configuration on PFC commands
- implement PTP adjphase function for HW offset control
- TC support for Geneve and GRE with VF tunnel offload
- more efficient crypto key management method
- multi-port eswitch support
- Netronome/Corigine:
- add DCB IEEE support
- support IPsec offloading for NFP3800
- Freescale/NXP (enetc):
- support XDP_REDIRECT for XDP non-linear buffers
- improve reconfig, avoid link flap and waiting for idle
- support MAC Merge layer
- Other NICs:
- sfc/ef100: add basic devlink support for ef100
- ionic: rx_push mode operation (writing descriptors via MMIO)
- bnxt: use the auxiliary bus abstraction for RDMA
- r8169: disable ASPM and reset bus in case of tx timeout
- cpsw: support QSGMII mode for J721e CPSW9G
- cpts: support pulse-per-second output
- ngbe: add an mdio bus driver
- usbnet: optimize usbnet_bh() by avoiding unnecessary queuing
- r8152: handle devices with FW with NCM support
- amd-xgbe: support 10Mbps, 2.5GbE speeds and rx-adaptation
- virtio-net: support multi buffer XDP
- virtio/vsock: replace virtio_vsock_pkt with sk_buff
- tsnep: XDP support
- Ethernet high-speed switches:
- nVidia/Mellanox (mlxsw):
- add support for latency TLV (in FW control messages)
- Microchip (sparx5):
- separate explicit and implicit traffic forwarding rules, make
the implicit rules always active
- add support for egress DSCP rewrite
- IS0 VCAP support (Ingress Classification)
- IS2 VCAP filters (protos, L3 addrs, L4 ports, flags, ToS
etc.)
- ES2 VCAP support (Egress Access Control)
- support for Per-Stream Filtering and Policing (802.1Q,
8.6.5.1)
- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- add MAB (port auth) offload support
- enable PTP receive for mv88e6390
- NXP (ocelot):
- support MAC Merge layer
- support for the the vsc7512 internal copper phys
- Microchip:
- lan9303: convert to PHYLINK
- lan966x: support TC flower filter statistics
- lan937x: PTP support for KSZ9563/KSZ8563 and LAN937x
- lan937x: support Credit Based Shaper configuration
- ksz9477: support Energy Efficient Ethernet
- other:
- qca8k: convert to regmap read/write API, use bulk operations
- rswitch: Improve TX timestamp accuracy
- Intel WiFi (iwlwifi):
- EHT (Wi-Fi 7) rate reporting
- STEP equalizer support: transfer some STEP (connection to radio
on platforms with integrated wifi) related parameters from the
BIOS to the firmware.
- Qualcomm 802.11ax WiFi (ath11k):
- IPQ5018 support
- Fine Timing Measurement (FTM) responder role support
- channel 177 support
- MediaTek WiFi (mt76):
- per-PHY LED support
- mt7996: EHT (Wi-Fi 7) support
- Wireless Ethernet Dispatch (WED) reset support
- switch to using page pool allocator
- RealTek WiFi (rtw89):
- support new version of Bluetooth co-existance
- Mobile:
- rmnet: support TX aggregation"
* tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1872 commits)
page_pool: add a comment explaining the fragment counter usage
net: ethtool: fix __ethtool_dev_mm_supported() implementation
ethtool: pse-pd: Fix double word in comments
xsk: add linux/vmalloc.h to xsk.c
sefltests: netdevsim: wait for devlink instance after netns removal
selftest: fib_tests: Always cleanup before exit
net/mlx5e: Align IPsec ASO result memory to be as required by hardware
net/mlx5e: TC, Set CT miss to the specific ct action instance
net/mlx5e: Rename CHAIN_TO_REG to MAPPED_OBJ_TO_REG
net/mlx5: Refactor tc miss handling to a single function
net/mlx5: Kconfig: Make tc offload depend on tc skb extension
net/sched: flower: Support hardware miss to tc action
net/sched: flower: Move filter handle initialization earlier
net/sched: cls_api: Support hardware miss to tc action
net/sched: Rename user cookie and act cookie
sfc: fix builds without CONFIG_RTC_LIB
sfc: clean up some inconsistent indentings
net/mlx4_en: Introduce flexible array to silence overflow warning
net: lan966x: Fix possible deadlock inside PTP
net/ulp: Remove redundant ->clone() test in inet_clone_ulp().
...
|
|
Pull SoC DT updates from Arnd Bergmann:
"About a quarter of the changes are for 32-bit arm, mostly filling in
device support for existing machines and adding minor cleanups, mostly
for Qualcomm and Samsung based machines.
Two new 32-bit SoCs are added, both are quad-core Cortex-A7 chips from
Rockchips that have been around for a while but were lacking kernel
support so far: RV1126 is a Vision SoC with an NPU and is used in the
Edgeble Neural Compute Module 2(Neu2) board, while RK3128 is design
for TV boxes and so far only comes with a dts for its refernece
design.
The other 32-bit boards that were added are two ASpeed AST2600 based
BMC boards, the Microchip sam9x60_curiosity development board (Armv5
based!), the Enclustra PE1 FPGA-SoM baseboard, and a few more boards
for i.MX53 and i.MX6ULL.
On the RISC-V side, there are fewer patches, but a total of ten new
single-board computers based on variations of the Allwinner D1/T113
chip, plus one more board based on Microchip Polarfire.
As usual, arm64 has by far the most changes here, with over 700
non-merge changesets, among them over 400 alone for Qualcomm. The
newly added SoCs this time are all recent high-end embedded SoCs for
various markets, each on comes with support for its reference board:
- Qualcomm SM8550 (Snapdragon 8 Gen 2) for mobile phones
- Qualcomm QDU1000/QRU1000 5G RAN platform
- Rockchips RK3588/RK3588s for tablets, chromebooks and SBCs
- TI J784S4 for industrial and automotive applications
In total, there are 46 new arm64 machines:
- Reference platforms for each of the five new SoCs
- Three Amlogic based development boards
- Six embedded machines based on NXP i.MX8MM and i.MX8MP
- The Mediatek mt7986a based Banana Pi R3 router
- Six tablets based on Qualcomm MSM8916 (Snapdragon 410), SM6115
(Snapdragon 662) and SM8250 (Snapdragon 865)
- Two LTE dongles, also based on MSM8916
- Seven mobile phones, based on Qualcomm MSM8953 (Snapdragon 610),
SDM450 and SDM632
- Three chromebooks based on Qualcomm SC7280 (Snapdragon 7c)
- Nine development boards based on Rockchips RK3588, RK3568, RK3566
and RK3328.
- Five development machines based on TI K3 (AM642/AM654/AM68/AM69)
The cleanup of dtc warnings continues across all platforms, adding to
the total number of changes"
* tag 'soc-dt-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (1035 commits)
dt-bindings: riscv: correct starfive visionfive 2 compatibles
ARM: dts: socfpga: Add enclustra PE1 devicetree
dt-bindings: altera: Add enclustra mercury PE1
arm64: dts: qcom: msm8996: align RPM G-Link clock-controller node with bindings
arm64: dts: qcom: qcs404: align RPM G-Link node with bindings
arm64: dts: qcom: ipq6018: align RPM G-Link node with bindings
arm64: dts: qcom: sm8550: remove invalid interconnect property from cryptobam
arm64: dts: qcom: sc7280: Adjust zombie PWM frequency
arm64: dts: qcom: sc8280xp-pmics: Specify interrupt parent explicitly
arm64: dts: qcom: sm7225-fairphone-fp4: enable remaining i2c busses
arm64: dts: qcom: sm7225-fairphone-fp4: move status property down
arm64: dts: qcom: pmk8350: Use the correct PON compatible
arm64: dts: qcom: sc8280xp-x13s: Enable external display
arm64: dts: qcom: sc8280xp-crd: Introduce pmic_glink
arm64: dts: qcom: sc8280xp: Add USB-C-related DP blocks
arm64: dts: qcom: sm8350-hdk: enable GPU
arm64: dts: qcom: sm8350: add GPU, GMU, GPU CC and SMMU nodes
arm64: dts: qcom: sm8350: finish reordering nodes
arm64: dts: qcom: sm8350: move more nodes to correct place
arm64: dts: qcom: sm8350: reorder device nodes
...
|
|
net/core/gro.c
7d2c89b32587 ("skb: Do mix page pool and page referenced frags in GRO")
b1a78b9b9886 ("net: add support for ipv4 big tcp")
https://lore.kernel.org/all/20230203094454.5766f160@canb.auug.org.au/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
net10 is connected to an SFP module. Unfortunately, the I2C lines are
not connected due to an address conflict. Now that DPAA uses phylink, we
can use in-band-status. This lets us determine whether the link is up or
down instead of assuming it is up all the time. Also fix the phy mode
while we're here.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
