| Age | Commit message (Collapse) | Author |
|---|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The interrupt-map property used in the description of the Marvell
Armada 7K/8K PCIe controllers has a bogus extraneous 0 that causes the
interrupt conversion to not be done properly. This causes the PCIe PME
and AER root port service drivers to fail their initialization:
[ 5.019900] genirq: Setting trigger mode 7 for irq 114 failed (irq_chip_set_type_parent+0x0/0x30)
[ 5.028821] pcie_pme: probe of 0001:00:00.0:pcie001 failed with error -22
[ 5.035687] genirq: Setting trigger mode 7 for irq 114 failed (irq_chip_set_type_parent+0x0/0x30)
[ 5.044614] aer: probe of 0001:00:00.0:pcie002 failed with error -22
This problem was introduced when the interrupt description was
switched from using the GIC directly to using the ICU interrupt
controller. Indeed, the GIC has address-cells = <1>, which requires a
parent unit address, while the ICU has address-cells = <0>.
Fixes: 6ef84a827c37 ("arm64: dts: marvell: enable GICP and ICU on Armada 7K/8K")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Yehuda Yitschak <yehuday@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Extend the container size to 0x2000 to include the gpio controller at
offset 0x1040.
While at it, add start address notation to the gpio node name to match
its 'offset' property.
Fixes: 63dac0f4924b ("arm64: dts: marvell: add gpio support for Armada
7K/8K")
Cc: <stable@vger.kernel.org>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM/arm64 Devicetree updates from Olof Johansson:
"As usual, device tree updates is the bulk of our material in this
merge window. This time around, 559 patches affecting both 32- and
64-bit platforms.
Changes are too many to list individually, but some of the larger
ones:
New platform/SoC support:
- Automotive:
+ Renesas R-Car D3 (R8A77995)
+ TI DT76x
+ MediaTek mt2712e
- Communication-oriented:
+ Qualcomm IPQ8074
+ Broadcom Stingray
+ Marvell Armada 8080
- Set top box:
+ Uniphier PXs3
Besides some vendor reference boards for the SoC above, there are also
several new boards/machines:
- TI AM335x Moxa UC-8100-ME-T open platform
- TI AM57xx Beaglebone X15 Rev C
- Microchip/Atmel sama5d27 SoM1 EK
- Broadcom Raspberry Pi Zero W
- Gemini-based D-Link DIR-685 router
- Freescale i.MX6:
+ Toradex Apalis module + Apalis and Ixora carrier boards
+ Engicam GEAM6UL Starter Kit
- Freescale i.MX53-based Beckhoff CX9020 Embedded PC
- Mediatek mt7623-based BananaPi R2
- Several Allwinner-based single-board computers:
+ Cubietruck plus
+ Bananapi M3, M2M and M64
+ NanoPi A64
+ A64-OLinuXino
+ Pine64
- Rockchip RK3328 Pine64/Rock64 board support
- Rockchip RK3399 boards:
+ RK3399 Sapphire module on Excavator carrier (RK3399 reference design)
+ Theobroma Systems RK3399-Q7 SoM
- ZTE ZX296718 PCBOX Board"
* tag 'armsoc-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (559 commits)
ARM: dts: at91: at91sam9g45: add AC97
arm64: dts: marvell: mcbin: enable more networking ports
arm64: dts: marvell: add a reference to the sysctrl syscon in the ppv2 node
arm64: dts: marvell: add TX interrupts for PPv2.2
arm64: dts: uniphier: add PXs3 SoC support
ARM: dts: uniphier: add pinctrl groups of ethernet phy mode
ARM: dts: uniphier: fix size of sdctrl nodes
ARM: dts: uniphier: add AIDET nodes
arm64: dts: uniphier: fix size of sdctrl node
arm64: dts: uniphier: add AIDET nodes
Revert "ARM: dts: sun8i: h3: Enable dwmac-sun8i on the Beelink X2"
arm64: dts: uniphier: add reset controller node of analog amplifier
arm64: dts: marvell: add Device Tree files for Armada-8KP
arm64: dts: rockchip: add Haikou baseboard with RK3399-Q7 SoM
arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM
dt-bindings: add rk3399-q7 SoM
ARM: dts: rockchip: enable usb for rv1108-evb
ARM: dts: rockchip: add usb nodes for rv1108 SoCs
dt-bindings: update grf-binding for rv1108 SoCs
ARM: dts: aspeed-g4: fix AHB window size of the SMC controllers
...
|
|
The Armada AP806 has 20 pins, and therefore 20 GPIOs (from 0 to 19
included) and not 19 pins. Therefore, we fix the Device Tree
description for the GPIO controller.
Before this patch:
$ cat /sys/kernel/debug/pinctrl/f06f4000.system-controller:pinctrl/gpio-ranges
GPIO ranges handled:
0: mvebu-gpio GPIOS [0 - 19] PINS [0 - 19]
0: f06f4000.system-controller:gpio GPIOS [0 - 18] PINS [0 - 18]
After this patch:
$ cat /sys/kernel/debug/pinctrl/f06f4000.system-controller:pinctrl/gpio-ranges
GPIO ranges handled:
0: mvebu-gpio GPIOS [0 - 19] PINS [0 - 19]
0: f06f4000.system-controller:gpio GPIOS [0 - 19] PINS [0 - 19]
Fixes: 63dac0f4924b9 ("arm64: dts: marvell: add gpio support for Armada 7K/8K")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
This patch enables the two GE/SFP ports. They are configured in 10GKR
mode by default. To do this the cpm_xdmio is enabled as well, and two
phy descriptions are added.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The network driver on Marvell SoC (7k/8k) needs to access some registers
in the system controller to configure its ports at runtime. This patch
adds a phandle reference to the syscon system controller node in the
ppv2 node.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
This commit updates the Marvell Armada 7K/8K Device Tree to describe
the TX interrupts of the Ethernet controllers, in both the master and
slave CP110s.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
This commit adds the base Device Tree files for the Armada 8KPlus.
The Armada 8KP SoCs include several hardware blocks, and this
commit only adds support for the AP810 block, that contains the CPU
core and basic peripherals.
AP810 is a high-performance die, includes octal core application
processor based ARMv8-A architecture, two standard high speed DDR4
interface, and GIC-600 interrupt controller.
AP810 Built as part of Marvell’s MoChi AP family products.
Armada-8080 (8KPlus family), include an AP810 block that contains
the CPU core and basic peripherals.
This commit creates the following hierarchy:
* armada-ap810-ap0.dtsi - definitions common to AP810
* armada-ap810-ap0-octa-core.dtsi - description of the octa cores
* armada-8080.dtsi - description of the 8080 SoC
* armada-8080-db.dts - description of the 8080 board
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Enable USB host on Armada-8040-DB by adding USB PHY nodes for the
following ports:
- host 0 and 1 of CPM
- host 0 of CPS
These PHY are enabled by lanes coming from regulators based on two
I2C expanders.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Add I2C expander and USB host PHY (host 0 and host 1) to enable
USB VBUS on USB ports of type A on Armada-7040-DB.
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The NAND controller used in A7K/A8K is present on the CP110. It is
compatible with the pxa-nand driver.
However, due to the limiation of the pins available this controller is
only usable on the CPM for A7K and on the CPS for A8K.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The ESPRESSObin board exposes one of the SDHCI interfaces
via J1 uSD slot. This patch enables it.
Tested-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Zbigniew Bodek <zbodek@gmail.com>
[gregory.clement@free-electrons.com: removed "no-1-8-v"]
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Since the introduction of the CP110 dt files, the sata node was
misplaced. Move it at the right place. Thanks to this, the files are
completely ordered.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
In both the CP110 master and slave description, the node describing
the RTC was at the wrong place when taking into account increasing
register addresses. Interestingly, it was not even at the same (wrong)
place in both files.
This commit adjusts that, making the master and slave descriptions
more aligned.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
This patch adds an stdout-path to the mcbin device tree. This allows to
use earlycon.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Add support for PCIe with the the PCIe reset signal wired up to the
appropriate GPIO pin.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
(excepted the reset part)
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The MACCHIATOBin board has a PCA9548 I2C mux for the SFP ports on
CP100 master I2C bus 1. Add the DT description for it.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Due to the lack of GPIO support, the USB3 regulator definition was
left unfinished in the MacchiatoBin DT description. Now that GPIO
support is available, this commit adjusts the Device Tree to properly
describe the USB3 regulator.
[gregory.clement@free-electrons.com: use commit log from Thomas]
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Add pinctrl nodes to describe the CPM I2C0 and CPS SPI1 settings.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Add the GPIO interrupts for the CP110.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The Espressobin SBC has a USB2 interface available on J8. Let's
enable it.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The Cortex-A53s that power the Armada-37xx SoCs are equipped with
a PMUv3, just like most ARMv8 cores.
Advertise the PMUv3 presence in the device tree, and wire its
interrupt. This allows the perf subsystem to work correctly.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The Cortex-A53s that power the Armada-37xx SoCs are equipped with
a GIC CPU interface that gets enabled when coupled with a GICv3
interrupt controller, such as the GIC-500 on the this SoC.
Advertise the MMIO ranges provided by the CPUs, which enables
(among other things) GICv2 guests to run under a hypervisor such
as KVM.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The GIC-500 integrated in the Armada-37xx SoCs is compliant with
the GICv3 architecture, and thus provides a maintenance interrupt
that is required for hypervisors to function correctly.
With the interrupt provided in the DT, KVM now works as it should.
Tested on an Espressobin system.
Fixes: adbc3695d9e4 ("arm64: dts: add the Marvell Armada 3700 family and
a development board")
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The number of pins in South Bridge is 30 and not 29. There is a fix for
the driver for the pinctrl, but a fix is also need at device tree level
for the GPIO.
Fixes: afda007feda5 ("ARM64: dts: marvell: Add pinctrl nodes for Armada
3700")
Cc: <stable@vger.kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The crypto engines found on the cp110 master and slave are dma coherent.
This patch adds the relevant property to their dt nodes.
Cc: stable@vger.kernel.org # v4.12+
Fixes: 973020fd9498 ("arm64: marvell: dts: add crypto engine description for 7k/8k")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
When the conversion of the Marvell CP110 Device Tree description from
using GIC interrupts to using ICU interrupts was done, the RTC on the
slave CP110 was left unchanged. This commit fixes that, so that all
devices on the CP properly get their interrupt through the ICU.
Fixes: 6ef84a827c375 ("arm64: dts: marvell: enable GICP and ICU on Armada 7K/8K")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
next/dt64
Pull "late dt64 for 4.13" from Gregory CLEMENT:
It is actually a patch that missed the end of the 4.12 merge
window. The patch itself fix a bogus definition of the timer for the
Armada 37xx SoCs.
* tag 'mvebu-dt64-4.13-3' of git://git.infradead.org/linux-mvebu:
ARM64: dts: marvell: armada37xx: Fix timer interrupt specifiers
|
|
Contrary to popular belief, PPIs connected to a GICv3 to not have
an affinity field similar to that of GICv2. That is consistent
with the fact that GICv3 is designed to accomodate thousands of
CPUs, and fitting them as a bitmap in a byte is... difficult.
Fixes: adbc3695d9e4 ("arm64: dts: add the Marvell Armada 3700 family and
a development board")
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
As I found by chance while merging another patch, the usage of
a dma-mask in this DT node is wrong for multiple reasons:
- dma-masks are a Linux specific concept, not a general
hardware feature
- In DT, we use the "dma-ranges" property to describe how DMA
addresses related between devices.
- The 40-bit mask appears to be completely unnecessary here, as
the SoC cannot address that much memory anyway, so simply
asking for a 64-bit mask (as supported by the device) should
succeed anyway.
The patch to remove the parsing of the property is getting merged
through the crypto tree.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
next/dt64
mvebu fixes for 4.12
Fix the interrupt description of the crypto node for device tree of
the Armada 7K/8K SoCs
* tag 'mvebu-fixes-4.12-1' of git://git.infradead.org/linux-mvebu:
arm64: marvell: dts: fix interrupts in 7k/8k crypto nodes
|
|
This commit modifies the Marvell EBU Armada 7K and 8K Device Tree files
to describe the ICU and GICP units, and use ICU interrupts for all
devices in the CP110 blocks.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Enable gpio support for CP and AP on the Marvell Armada 7K/8K SoCs.
The Armada 8K has two CP110 blocks, each having two GPIO controllers.
However, in each CP110 block, one of the GPIO controller cannot be
used: in the master CP110, only the second GPIO controller can be used,
while on the slave CP110, only the first GPIO controller can be used.
On the other side, the Armada 7K has only one CP110, but both its GPIO
controllers can be used.
For this reason, the GPIO controllers are marked as "disabled" in the
armada-cp110-master.dtsi and armada-cp110-slave.dtsi files, and only
enabled in the per-SoC dtsi files.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Enable pinctrl support for CP and AP on the Armada 7K/8K SoCs.
The CP master being different between Armada 7k and Armada 8k. This
commit introduces the intermediates files armada-70x0.dtsi and
armada-80x0.dtsi.
These new files will provide different compatible strings depending of
the SoC family. They will also be the location for the pinmux
configuration at the SoC level.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The new binding for the system controller on cp110 moved the clock
controller into a subnode. This preliminary step will allow to add gpio
and pinctrl subnodes.
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The *-clock-output-names of the cp110-system-controller0 node are not
used anymore, so remove them.
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
New bindings are used for the system controller on the ap806, which
means all clock properties must be converted. Use the new bindings in
the xor nodes.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Since the mdio nodes are disabled by default now, we should explicitly
enable these nodes at the board level when they are used. Enable the
cpm_mdio node for the 8040-mcbin.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Add the description of the xMDIO bus for the Marvell Armada 7k and
Marvell Armada 8k; for both CP110 slave and master. This bus is found
on Marvell Ethernet controllers and provides an interface with the
xMDIO bus.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The cryptographic engine found on the cp110 slave is disabled by default
because of some known limitations. Add a comment to explain why it is
disabled by default.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The cryptographic engine on the master cp110 is now enabled by default
at the SoC level. Remove its dts nodes that were only enabling it.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Enable the cryptographic engine at the SoC level on the master cp110.
This engine is always present and do not depends on any pinmux
configuration.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
By adding this regulator, the SD cards are usable at higher speed
protocols such as SDR104.
This patch was tested with an SD HC card compatible with UHS-I.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The Armada 37xx SoCs has 2 SDHCI interfaces. This patch adds the second
one.
Moreover, the Armada 37xx DB v2 board populates the 2 SDHCI interfaces.
The second interface is using pluggable module that can either
have an SD connector or eMMC on it.
This patch adds support for SD module in the device DT.
[ gregory.clement@free-electrons.com:
- Add more detail in commit log
- Sort the dt node in address order
- Document the SD slot in the dts ]
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
When several groups of register address and size are used with reg, then
surround each one by angle bracket.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
This cosmetic patch aligns the compatible string when there are on
several lines.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The initial device tree file was for the board V1.4. Now the V2.0 board
is also available. The same dtb will work for both, but the CON number
have changed, so update the comment in the dts to reflect this.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Sort the reference nodes in alphabetical order to ease the merge of
future nodes.
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Disable the mdio nodes by default in the cp110 slave and master dtsi as
they're not wired on every board.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
