| Age | Commit message (Collapse) | Author |
|---|
|
This adds support for the Turris Mox board from CZ.NIC.
Turris Mox is as modular router based on the Armada 3720 SOC (same as
EspressoBin).
The basic board can be extended by different modules.
If those are connected, U-Boot lets the kernel know via device-tree.
Since modules can be connected in different order and some modules can
be connected multiple times (up to three modules containing 8-port
ethernet switch in DSA configuration can be connected) we decided
against using device-tree overlays, because it got complicated rather
quickly. (For example the SFP module can be connected directly to the
CPU, or after a switch module. There are four cases and all would need
different SFP overlay. There are two types of switch modules (8-port
with pass-through and 4-port with no pass-through). For those we would
again need at least 6 more overlays.)
We therefore decided to put all the possibly connected devices in one
device-tree and disable them by default. When U-Boot finds out which
modules are connected, it fixes the loaded device-tree accordingly just
before boot. By Rob Herring's suggestion we also made it so that U-Boot
completely removes nodes which are disabled after this fixup.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Rob Herring <robh@kernel.org>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
This adds pinctrl node for the GPIO to be used as SPI chip select 1.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Add cpu clock node on AP
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Update Aramda 7k/8k DTs to use the phy-supply property of the (recent)
generic PHY framework instead of the (legacy) usb-phy preperty. Both
enable the supply when the PHY is enabled.
The COMPHY nodes only provide SERDES lanes configuration. The power
supply that is represented by the phy-supply property is just a
regulator wired to the USB connector, hence the creation of connector
nodes as child of the COMPHY nodes and the supply attached to it.
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Fill-in the missing PCIe phys/phy-names DT properties of Armada 7k/8k
based boards.
The MacchiatoBin is a bit particular as the Armada8k-PCI IP supports
x4 link widths and in this case the PHY for each lane must be
referenced.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Fill-in the missing USB3 phys/phy-names DT properties of Armada 7k/8k
based boards. Only update nodes actually enabling USB3 in the default
(mainline) configuration. A few USB nodes are enabled but there is
only USB2 working on them.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Fill-in the missing SATA phys/phy-names DT properties of Armada 7k/8k
based boards.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Declare the three clocks feeding the COMPHY block.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
This adds the rWTM BIU mailbox node for communication with the secure
processor. The driver already exists in
drivers/mailbox/armada-37xx-rwtm-mailbox.c.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Gregory Clement <gregory.clement@bootlin.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The GPIO interrupt controllers are missing their required
specified in DT.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Armada 7040-db USB ports deliver 500mA by default while they
could deliver up to 900mA (usually, for USB3 devices).
The board embeds a GPIO controlled regulator on each port which can be
configured to deliver each amount of current.
Add a vin-supply property to the USB3 Vbus nodes for this purpose. The
regulator will be automatically 'enabled', ie. set to limit at 900mA
instead of 500mA.
Suggested-by: Alex Leibovich <alexl@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The manufacturer of this board, ships it with various SPI NOR chips and
increments U-Boot bootloader version along the time. There is no way to
tell which is placed on the board since no revision bump takes place.
This creates two issues.
The first, cosmetic. Since the NOR chip may differ, there's message on
boot stating that kernel expected w25q32dw and found different one. To
correct this, remove optional device-specific compatible string. Being
here lets replace bogus "spi-flash" compatible string with proper one.
The second is linked to partitions layout, it changed after commit:
81e7251252 ("arm64: mvebu: config: move env to the end of the 4MB boot
device") in Marvells downstream U-Boot fork [1], shifting environment
location to the end of boot device. Since the new boards will have U-Boot
with this change, it'll lead to improper results writing or reading from
these partitions. We can't tell if users will update bootloader to recent
version provided on manufacturer website, so lets drop partitons layout.
1. https://github.com/MarvellEmbeddedProcessors/u-boot-marvell.git
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
While AP I2C bus was available to users in early revisions of the SoC,
this is not the case anymore since eMMC was connected to the AP. Most
users do not have access to this I2C bus so do not enable it in the
board device tree.
As there are three I2C buses enabled on this board, add an alias to be
sure the two other buses keep their initial numbering.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
[<miquel.raynal@bootlin.com>: Reword commit message, add alias]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Avoid critical temperatures in the AP806 by adding the relevant trip
points/cooling-maps using CPUfreq as cooling device.
So far, when the temperature reaches 100°C in the thermal IP of the
AP806 (close enough from the 2/4 cores) an overheat interrupt is
raised. The thermal core then shutdowns the system to avoid damaging
the hardware.
Adding CPUfreq as a cooling device could help avoiding such very
critical situation. For that, we enable thermal throttling by
defining, for each CPU, two trip points with the corresponding cooling
'intensity'. CPU0 and CPU1 are in the same cluster and are driven by
the same clock. Same applies for CPU2 and CPU3, if available. So
changing the frequency of one will also change the frequency of the
other one, hence the use of two cooling devices per core.
The heat map is as follow:
- Below 85°C: the cluster runs at the highest frequency
(e.g: 1200MHz).
- Between 85°C and 95°C: there are two trip points at half
(e.g: 600MHz) and a third (e.g: 400MHz) of the highest frequency.
- Above 95°C the cluster runs at a quarter of the highest frequency
(e.g: 300MHz).
- At 100°C the platform is shutdown.
Suggested-by: Omri Itach <omrii@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
When adding thermal nodes, the CPUs have been named from 1 to 4 while
usually everywhere else they are referred as 0-3. Let's change this to
be consistent with later changes when we will use CPUfreq and CPU
phandles as cooling devices to avoid inconsistencies in the nodes
numbering.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The Clearfog GT-8K board is capable of supplying power up to 2W to SFP
modules. Make that explicit in the device-tree. Without this property
current kernel does not allow SFP modules that require more than 1W.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Running a graphics adapter on the MACCHIATObin fails due to an
insufficiently sized memory window.
Enlarge the memory window for the PCIe slot to 512 MiB.
With the patch I am able to use a GT710 graphics adapter with 1 GB onboard
memory.
These are the mapped memory areas that the graphics adapter is actually
using:
Region 0: Memory at cc000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at c0000000 (64-bit, prefetchable) [size=128M]
Region 3: Memory at c8000000 (64-bit, prefetchable) [size=32M]
Region 5: I/O ports at 1000 [size=128]
Expansion ROM at ca000000 [disabled] [size=512K]
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
There is currently no DT binding for GPIO rfkill signals. To make
mini-PCIe attached WiFi devices work, use gpio-hog to hold the
wlan_disable signal de-asserted.
Signed-off-by: Thomas Schreiber <tschreibe@gmail.com>
[baruch: add pinctrl node; rename tag]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Pull ARM SoC device tree updates from Arnd Bergmann:
"This is a smaller update than the past few times, but with just over
500 non-merge changesets still dwarfes the rest of the SoC tree.
Three new SoC platforms get added, each one a follow-up to an existing
product, and added here in combination with a reference platform:
- Renesas RZ/A2M (R7S9210) 32-bit Cortex-A9 Real-time imaging
processor:
https://www.renesas.com/eu/en/products/microcontrollers-microprocessors/rz/rza/rza2m.html
- Renesas RZ/G2E (r8a774c0) 64-bit Cortex-A53 SoC "for Rich Graphics
Applications":
https://www.renesas.com/eu/en/products/microcontrollers-microprocessors/rz/rzg/rzg2e.html
- NXP i.MX8QuadXPlus 64-bit Cortex-A35 SoC:
https://www.nxp.com/products/processors-and-microcontrollers/arm-based-processors-and-mcus/i.mx-applications-processors/i.mx-8-processors/i.mx-8x-family-arm-cortex-a35-3d-graphics-4k-video-dsp-error-correcting-code-on-ddr:i.MX8X
These are actual commercial products we now support with an in-kernel
device tree source file:
- Bosch Guardian is a product made by Bosch Power Tools GmbH, based
on the Texas Instruments AM335x chip
- Winterland IceBoard is a Texas Instruments AM3874 based machine
used in telescopes at the south pole and elsewhere, see commit
d031773169df2 for some pointers:
- Inspur on5263m5 is an x86 server platform with an Aspeed ast2500
baseboard management controller. This is for running on the BMC.
- Zodiac Digital Tapping Unit, apparently a kind of ethernet switch
used in airplanes.
- Phicomm K3 is a WiFi router based on Broadcom bcm47094
- Methode Electronics uDPU FTTdp distribution point unit
- X96 Max, a generic TV box based on Amlogic G12a (S905X2)
- NVIDIA Shield TV (Darcy) based on Tegra210
And then there are several new SBC, evaluation, development or modular
systems that we add:
- Three new Rockchips rk3399 based boards:
- FriendlyElec NanoPC-T4 and NanoPi M4
- Radxa ROCK Pi 4
- Five new i.MX6 family SoM modules and boards for industrial
products:
- Logic PD i.MX6QD SoM and evaluation baseboad
- Y Soft IOTA Draco/Hydra/Ursa family boards based on i.MX6DL
- Phytec phyCORE i.MX6 UltraLite SoM and evaluation module
- MYIR Tech MYD-LPC4357 development based on the NXP lpc4357
microcontroller
- Chameleon96, an Intel/Altera Cyclone5 based FPGA development system
in 96boards form factor
- Arm Fixed Virtual Platforms(FVP) Base RevC, a purely virtual
platform for corresponding to the latest "fast model"
- Another Raspberry Pi variant: Model 3 A+, supported both in 32-bit
and 64-bit mode.
- Oxalis Evalkit V100 based on NXP Layerscape LS1012a, in 96Boards
enterprise form factor
- Elgin RV1108 R1 development board based on 32-bit Rockchips RV1108
For already supported boards and SoCs, we often add support for new
devices after merging the drivers. This time, the largest changes
include updates for
- STMicroelectronics stm32mp1, which was now formally launched last
week
- Qualcomm Snapdragon 845, a high-end phone and low-end laptop chip
- Action Semi S700
- TI AM654x, their recently merged 64-bit SoC from the OMAP family
- Various Amlogic Meson SoCs
- Mediatek MT2712
- NVIDIA Tegra186 and Tegra210
- The ancient NXP lpc32xx family
- Samsung s5pv210, used in some older mobile phones
Many other chips see smaller updates and bugfixes beyond that"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (506 commits)
ARM: dts: exynos: Fix max voltage for buck8 regulator on Odroid XU3/XU4
dt-bindings: net: ti: deprecate cpsw-phy-sel bindings
ARM: dts: am335x: switch to use phy-gmii-sel
ARM: dts: am4372: switch to use phy-gmii-sel
ARM: dts: dm814x: switch to use phy-gmii-sel
ARM: dts: dra7: switch to use phy-gmii-sel
arch: arm: dts: kirkwood-rd88f6281: Remove disabled marvell,dsa reference
ARM: dts: exynos: Add support for secondary DAI to Odroid XU4
ARM: dts: exynos: Add support for secondary DAI to Odroid XU3
ARM: dts: exynos: Disable ARM PMU on Odroid XU3-lite
ARM: dts: exynos: Add stdout path property to Arndale board
ARM: dts: exynos: Add minimal clkout parameters to Exynos3250 PMU
ARM: dts: exynos: Enable ADC on Odroid HC1
arm64: dts: sprd: Remove wildcard compatible string
arm64: dts: sprd: Add SC27XX fuel gauge device
arm64: dts: sprd: Add SC2731 charger device
arm64: dts: sprd: Add ADC calibration support
arm64: dts: sprd: Remove PMIC INTC irq trigger type
arm64: dts: rockchip: Enable tsadc device on rock960
ARM: dts: rockchip: add chosen node on veyron devices
...
|
|
The PHY reset signal goes to mpp43 on CP0.
Fixes: babc5544c293 ("arm64: dts: clearfog-gt-8k: 1G eth PHY reset signal")
Reported-by: Denis Odintsov <oversun@me.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
mvebu dt64 for 5.1 (part 1)
- Interrupt support to Armada 7K/8K thermal nodes
- Armada 37xx related patches allowing to enable suspend to RAM
(USB2, USB3, PCIe, SATA, DSA)
- uDPU board support (Armada-3720 based):single-port FTTdp
distribution point unit
- Fixes for EspressoBin Ethernet support when using U-Boot mainline
- cleanup for partitions under flashes nodes
* tag 'mvebu-dt64-5.1-1' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: armada-37xx: link USB hosts with their PHYs
arm64: dts: marvell: armada-3720-espressobin: declare SATA PHY property
arm64: dts: marvell: armada-3720-espressobin: declare PCIe PHY
arm64: dts: marvell: armada-37xx: declare the COMPHY node
arm64: dts: marvell: Remove unnecessary #address-cells/#size-cells under flashes
arm64: dts: armada-3720-espressobin: Set mv88e6341 cpu port as RGMII-ID
arm64: dts: armada-3720-espressobin: Configure RGMII and SMI pins
arm64: dts: marvell: Add device tree for uDPU board
arm64: dts: marvell: armada-3720-espressobin: declare PCIe warm reset pin
arm64: dts: marvell: armada-37xx: declare PCIe reset pin
arm64: dts: marvell: armada-37xx: declare USB2 UTMI PHYs
arm64: dts: marvell: armada-37xx: fix USB2 memory region
arm64: dts: marvell: armada-37xx: declare SATA clock
arm64: dts: marvell: armada-37xx: fix SATA node scope
arm64: dts: marvell: add interrupt support to cp110 thermal node
arm64: dts: marvell: add interrupt support to ap806 thermal node
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Reference the PHY nodes from the USB controller nodes.
The USB3 host controller is wired to:
* the first PHY of the COMPHY IP
* the OTG-capable UTMI PHY
The USB2 host controller is wired to:
* the host-only UTMI PHY
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The SATA node is wired to the third PHY of the COMPHY IP.
Suggested-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The PCIe node is wired to the second PHY of the COMPHY IP.
Suggested-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Describe the A3700 COMPHY node. It has three PHYs that can be
configured as follow:
* PCIe or GbE
* USB3 or GbE
* SATA or USB3
Each of them has its own memory area.
Suggested-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
By using the new binding for the partitions for the flashes we don't need
anymore to use #size-cells and #address-cells at the flash node level.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The mv88e6341 ethernet switch needs the cpu port control register to be
set with TX and RX internal delay in order to work.
This fixes ethernet support on system booted via a bootloader that
has not already configured this register (e.g. mainline u-boot, or
vendor u-boot compiled without ethernet support).
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
In order to be able to communicate with the 88e6341 switch some pins
have to be repurposed as RGMII and SMI pins.
This fixes ethernet support on system booted via a bootloader that
has not already configured those pins (e.g. mainline u-boot, or vendor
u-boot compiled without ethernet support).
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
This adds initial support for micro-DPU (uDPU) board which is based on
Armada-3720 SoC. micro-DPU is the single-port FTTdp distribution point
unit made by Methode Electronics which offers complete modularity with
replaceable SFP modules both for uplink and downlink (G.hn over
twisted-pair, G.hn over coax, 1G and 2.5G Ethernet over Cat-5e cable).
On-board features:
- 512 MiB DDR3
- 2 x 2.5G SFP via HSGMII SERDES interface to the A3720 SoC
- USB 2.0 Type-C connector
- 4GB eMMC
- ETSI TS 101548 reverse powering via twisted pair (RJ45) or coax (F Type)
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Luis Torres <luis.torres@methode.com>
Cc: Scott Roberts <scott.roberts@telus.com>
Cc: Paul Arola <paul.arola@telus.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Gregory Clement <gregory.clement@bootlin.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Ensure the PCIe endpoint card reset that is toggled by the PCIe
controller itself is muxed correctly on the EspressoBin.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
One pin can be muxed as PCIe endpoint card reset.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
On Marvell Armada 3700 SoCs there are two USB2 UTMI PHYs. They are
both very similar but only one has OTG/charging capabilities.
Because there are USB host registers and PHY registers mixed in a
single area, a system controller is also created and referenced from
both the USB host node and the PHY node.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The specification splits the USB2 memory region into three sections:
1/ 0xD005E000-0xD005EFFF: USB2 Host Controller Registers
2/ 0xD005F000-0xD005F7FF: USB2 UTMI PHY Registers
3/ 0xD005F800-0xD005FFFF: USB2 Host Miscellaneous Registers
Section 1/ belongs to the USB2 node but section 2/ belongs to the UTMI
PHY node. Section 3/ can be accessed by both the USB controller and
the PHY because of the miscaellaneous nature of the registers inside
so a specific node will be created to cover the area and a handle to
it will be added in both the USB controller and the PHY node.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The SATA IP get its clock from the north-bridge.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Fix the SATA IP memory area which is only 0x178 bytes long (from
Marvell A3700 specification). Actually, starting from the offset
0xe0178, there is an area dedicated to the COMPHY driver.
Suggested-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Add interrupt properties in the thermal node as well as a critical trip
point in the thermal-zone.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Add interrupt properties in the thermal node as well as a critical trip
point in the thermal-zone.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The 'arm,armv8' compatible string is only for software models. It adds
little value otherwise and is inconsistently used as a fallback on some
platforms. Remove it from those platforms.
This fixes warnings generated by the DT schema.
Reported-by: Michal Simek <michal.simek@xilinx.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Chanho Min <chanho.min@lge.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Wei Xu <xuwei5@hisilicon.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Acked-by: Robert Richter <rrichter@cavium.com>
Acked-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The MPP52 signal is on the seconds GPIO instance of CP0, which
corresponds to the &cp0_gpio2 handle.
Rename the property name to the standard '-gpios' suffix while at it.
Fixes: b83e1669adce6 ("arm64: dts: marvell: mcbin: add support for PCIe")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The memory area [0x4000000-0x4200000[ is occupied by the PSCI firmware. Any
attempt to access it from Linux leads to an immediate crash.
So let's make the same memory reservation as the vendor kernel.
[gregory: added as comment that this region matches the mainline U-boot]
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM Device-tree updates from Olof Johansson:
"As usual, this is where the bulk of our changes end up landing each
merge window.
The individual updates are too many to enumerate, many many platforms
have seen additions of device descriptions such that they are
functionally more complete (in fact, this is often the bulk of updates
we see).
Instead I've mostly focused on highlighting the new platforms below as
they are introduced. Sometimes the introduction is of mostly a
fragment, that later gets filled in on later releases, and in some
cases it's near-complete platform support. The latter is more common
for derivative platforms that already has similar support in-tree.
Two SoCs are slight outliers from the usual range of additions.
Allwinner support for F1C100s, a quite old SoC (ARMv5-based) shipping
in the Lychee Pi Nano platform. At the other end is NXP Layerscape
LX2160A, a 16-core 2.2GHz Cortex-A72 SoC with a large amount of I/O
aimed at infrastructure/networking.
TI updates stick out in the diff stats too, in particular because they
have moved the description of their L4 on-chip interconnect to
devicetree, which opens up for removal of even more of their
platform-specific 'hwmod' description tables over the next few
releases.
SoCs:
- Qualcomm QCS404 (4x Cortex-A53)
- Allwinner T3 (rebranded R40) and f1c100s (armv5)
- NXP i.MX7ULP (1x Cortex-A7 + 1x Cortex-M4)
- NXP LS1028A (2x Cortex-A72), LX2160A (16x Cortex-A72)
New platforms:
- Rockchip: Gru Scarlet (RK3188 Tablet)
- Amlogic: Phicomm N1 (S905D), Libretech S805-AC
- Broadcom: Linksys EA6500 v2 Wi-Fi router (BCM4708)
- Qualcomm: QCS404 base platform and EVB
- Qualcomm: Remove of Arrow SD600
- PXA: First PXA3xx DT board: Raumfeld
- Aspeed: Facebook Backpack-CMM BMC
- Renesas iWave G20D-Q7 (RZ/G1N)
- Allwinner t3-cqa3t-bv3 (T3/R40) and Lichee Pi Nano (F1C100s)
- Allwinner Emlid Neutis N5, Mapleboard MP130
- Marvell Macchiatobin Single Shot (Armada 8040, no 10GbE)
- i.MX: mtrion emCON-MX6, imx6ul-pico-pi, imx7d-sdb-reva
- VF610: Liebherr's BK4 device, ZII SCU4 AIB board
- i.MX7D PICO Hobbit baseboard
- i.MX7ULP EVK board
- NXP LX2160AQDS and LX2160ARDB boards
Other:
- Coresight binding updates across the board
- CPU cooling maps updates across the board"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (648 commits)
ARM: dts: suniv: Fix improper bindings include patch
ARM: dts: sunxi: Enable Broadcom-based Bluetooth for multiple boards
arm64: dts: allwinner: a64: bananapi-m64: Add Bluetooth device node
ARM: dts: suniv: Fix improper bindings include patch
arm64: dts: Add spi-[tx/rx]-bus-width for the FSL QSPI controller
arm64: dts: Remove unused properties from FSL QSPI driver nodes
ARM: dts: Add spi-[tx/rx]-bus-width for the FSL QSPI controller
ARM: dts: imx6sx-sdb: Fix the reg properties for the FSL QSPI nodes
ARM: dts: Remove unused properties from FSL QSPI driver nodes
arm64: dts: ti: k3-am654: Enable main domain McSPI0
arm64: dts: ti: k3-am654: Add McSPI DT nodes
arm64: dts: ti: k3-am654: Populate power-domain property for UART nodes
arm64: dts: ti: k3-am654-base-board: Enable ECAP PWM
arm64: dts: ti: k3-am65-main: Add ECAP PWM node
arm64: dts: ti: k3-am654-base-board: Add I2C nodes
arm64: dts: ti: am654-base-board: Add pinmux for main uart0
arm64: dts: ti: k3-am65: Add pinctrl regions
dt-bindings: pinctrl: k3: Introduce pinmux definitions
ARM: dts: exynos: Specify I2S assigned clocks in proper node
ARM: dts: exynos: Add missing CPUs in cooling maps for Odroid X2
...
|
|
Enable the USB3 peripheral that is wired to CON2 on the Clearfog GT-8K
board.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Add DT support for the Macchiatobin Single Shot board from SolidRun,
which is similar to the Double Shot board, but does not have the
10G 3310 PHYs - the two ethernet ports are instead connected directly
to the SFP+ cages.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The ESPRESSObin board has a emmc interface available on U11: declare it
and let the bootloader enable it if the emmc is present.
[gregory.clement@bootlin.com: disable the emmc by default]
Signed-off-by: Ding Tao <miyatsu@qq.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
This reverts commit 8ed46368776b3bc93d74c1f8f2bfb9fd8a9ad805.
This commit breaks boot on Armada 8K based systems. Reverting it makes
affected systems boot again.
Reported-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Add emmc/sdio pinctrl definition for marvell armada37xx SoCs.
Signed-off-by: Ding Tao <miyatsu@qq.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Deassert the reset and wireless disable signals on the CON2 mini-PCIe
socket. That allows the host to detect USB devices on the mini-PCIe
socket.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
This reset signal controls the Marvell 1512 1G PHY.
Note that current implementation queries the PHY over the MDIO bus
(get_phy_device() call from of_mdiobus_register_phy()) before reset
signal deassert. If the PHY reset signal is asserted at boot time, PHY
registration fails. So current code relies on the bootloader to deassert
the reset signal.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The fixed regulator driver ignores the gpio flags, so this change has
no practical effect in the current implementation. Fix it anyway to
correct the hardware description.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
This adds support for the PCIe interface on the CON4 mini-PCIe
connector.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
