Age | Commit message (Collapse) | Author |
|
Add missing whitespace between node name/label and opening {.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230705145912.293315-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
I2C aliases are not a property of a SoC. They belong to board files
where they are named accordingly in the schematics.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220825071022.7864-3-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Describe all Ethernet PHY reset GPIOs on R-Car Gen3 boards, to avoid
relying solely on boot loaders to bring PHYs out of reset.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/3e6fd765850e8ef0980d8e98bc5f2126538d626f.1631177442.git.geert+renesas@glider.be
|
|
Add compatible values to Ethernet PHY subnodes representing Micrel
KSZ9031 PHYs on R-Car Gen3 boards. This allows software to identify the
PHY model at any time, regardless of the state of the PHY reset line.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/07bd7e04dda9e84cde0664980f0b1a6d69e03109.1631174218.git.geert+renesas@glider.be
|
|
The V3MSK board has 2 GiB RAM according to the datasheet and schematics.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
[geert: Verified schematics]
Fixes: cc3e267e9bb0ce7f ("arm64: dts: renesas: initial V3MSK board device tree")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210326121050.1578460-1-geert+renesas@glider.be
|
|
Some EtherAVB variants support internal clock delay configuration, which
can add larger delays than the delays that are typically supported by
the PHY (using an "rgmii-*id" PHY mode, and/or "[rt]xc-skew-ps"
properties).
Historically, the EtherAVB driver configured these delays based on the
"rgmii-*id" PHY mode. This was wrong, as these are meant solely for the
PHY, not for the MAC. Hence properties were introduced for explicit
configuration of these delays.
Convert the R-Car Gen3 DTS files from the old to the new scheme:
- Add default "rx-internal-delay-ps" and "tx-internal-delay-ps"
properties to the SoC .dtsi files, to be overridden by board files
where needed,
- Convert board files from "rgmii-*id" PHY modes to "rgmii", adding
the appropriate "rx-internal-delay-ps" and/or "tx-internal-delay-ps"
overrides.
Notes:
- R-Car E3 and D3 do not support TX internal delay handling,
- On R-Car D3, TX internal delay handling must always be enabled,
hence this fixes a bug on Draak,
- On R-Car V3H, RX internal delay handling must always be enabled.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200819134344.27813-7-geert+renesas@glider.be
|
|
Define the Eagle/V3MSK board dependent parts of the RPC-IF device node.
Add device nodes for Spansion S25FS512S SPI flash and MTD partitions on it.
Based on the original patches by Dmitry Shifrin.
Signed-off-by: Dmitry Shifrin <dmitry.shifrin@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Link: https://lore.kernel.org/r/fca1d012-29bf-eead-1c0d-4dd837c0bc68@cogentembedded.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Small fixes to make these DTs compliant with the adi,adv7511w binding.
r8a77970-eagle.dts,
r8a77970-v3msk.dts,
r8a77980-condor.dts,
r8a77980-v3hsk.dts,
r8a77990-ebisu.dts:
Remove the adi,input-style and adi,input-justification properties.
r8a77995-draak.dts:
Reorder the I2C slave addresses of the hdmi-encoder@39 node and
remove the adi,input-style and adi,input-justification properties.
Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200511110611.3142-2-ricardo.canuelo@collabora.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Specify EtherAVB PHY IRQ in the V3M Starter Kit board's device tree, now
that we have the GPIO support (previously phylib had to resort to polling).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add the eMMC chip support for the V3M Started Kit board.
Based on the original (and large) patches by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Define the V3M Starter Kit board dependent part of the DU and LVDS device
nodes. Also add the device nodes for Thine THC63LVD1024 LVDS decoder and
Analog Devices ADV7511W HDMI transmitter...
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add the (previously omitted) EtherAVB pin data to the V3M Starter Kit
board's device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add the (previously omitted) SCIF0 pin data to the V3M Starter Kit board's
device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
As the PHY interface installed on the V3MSK board provides TX and RX
channels delays, make the "phy-mode" property a board-specific one,
meant to override the one specified in the SoC DTSI.
Follow up patches will reset the r8a77970 SoC DTSI to use "rgmii"
mode and let the board file override that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Define the V3M Starter Kit board dependent part of the EtherAVB
device node.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add the initial device tree for the V3M Starter Kit board.
The board has 1 debug serial port (SCIF0); include support for it,
so that the serial console can work.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|