Age | Commit message (Collapse) | Author |
|
Most arm board have a board-specific compatible string that allows e.g.
userspace to match specific firmware variants or apply specific
policies.
Add board-specific properties to both variants of the Clearfog GTR:
- solidrun,clearfog-gtr-l8
- solidrun,clearfog-gtr-s4
Introduction of a common parent (e.g. "solidrun,clearfog-gtr") is
omitted for brevity.
Since announcement of the two products no additional variants were added
it is assumed that there will always be just two.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Armada 388 Clearfog ("armada-388-clearfog.dts)" is a legacy filename for
the Armada 388 Clearfog Pro ("armada-388-clearfog-pro.dts").
The "Pro" suffix was only used when the smaller version, the "Base" got
released.
The two names refer to exactly the same hardware, therefore they should
share the same compatible strings.
Copy "solidrun,clearfog-pro-a1" compatible from the -pro dts and add it
to this legacy file.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
As the TWL6030 chip is the main power controller here, declare
it as system-power-controller
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Message-ID: <20240217082007.3238948-5-andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Configure the TWL6032 as system power controller to let the device
power off.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Message-ID: <20240217082007.3238948-4-andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Move the pending urls back to https:// and mark the ones that are no
longer accessible (http or https) as defunct.
Signed-off-by: Nishanth Menon <nm@ti.com>
Message-ID: <20240109195500.3833121-1-nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
for dra7 SoC
abb_{mpu,ivahd,dspeve,gpu} have 'reg' so they must have unit address to fix dtc
W=1 warnings:
Warning (unit_address_vs_reg): /ocp/regulator-abb-mpu: node has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): /ocp/regulator-abb-ivahd: node has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): /ocp/regulator-abb-dspeve: node has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): /ocp/regulator-abb-gpu: node has a reg or ranges property, but no unit name
Signed-off-by: Romain Naour <romain.naour@skf.com>
Message-ID: <20240123085551.733155-3-romain.naour@smile.fr>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
sys_32k_ck node have 'reg' so it must have unit address to fix dtc
W=1 warnings:
Warning (unit_address_vs_reg): /ocp/interconnect@4a000000/segment@0/target-module@2000/scm@0/scm_conf@0/clocks/clock-sys-32k: node has a reg or ranges property, but no unit name
Signed-off-by: Romain Naour <romain.naour@skf.com>
Message-ID: <20240123085551.733155-2-romain.naour@smile.fr>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
phy_gmii_sel node have 'reg' so it must have unit address to fix dtc
W=1 warnings:
Warning (unit_address_vs_reg): /ocp/interconnect@4a000000/segment@0/target-module@2000/scm@0/scm_conf@0/phy-gmii-sel: node has a reg or ranges property, but no unit name
Signed-off-by: Romain Naour <romain.naour@skf.com>
Message-ID: <20240123085551.733155-1-romain.naour@smile.fr>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
For the clksel clocks we are still using the legacy ti,bit-shift property
instead of the standard reg property. We can now use the reg property, so
let's do that for the clksel clocks.
To add the reg property, we switch to use #address-cells = <1>.
For now let's not update the clock-dss-tv-fck as it seems to share the same
register bit as the clock-dss-96m-fck and would introduce more warnings.
Cc: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
For the clksel clocks we are still using the legacy ti,bit-shift property
instead of the standard reg property. We can now use the reg property, so
let's do that for the clksel clocks.
To add the reg property, we switch to use #address-cells = <1>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
PJ4 is a v7 core that incorporates a iWMMXt coprocessor. However, GCC
does not support this combination (its iWMMXt configuration always
implies v5te), and so there is no v6/v7 user space that actually makes
use of this, beyond generic support for things like setjmp() that
preserve/restore the iWMMXt register file using generic LDC/STC
instructions emitted in assembler. As [0] appears to imply, this logic
is triggered for the init process at boot, and so most user threads will
have a iWMMXt register context associated with it, even though it is
never used.
At this point, it is highly unlikely that such GCC support will ever
materialize (and Clang does not implement support for iWMMXt to begin
with).
This means that advertising iWMMXt support on these cores results in
context switch overhead without any associated benefit, and so it is
better to simply ignore the iWMMXt unit on these systems. So rip out the
support. Doing so also fixes the issue reported in [0] related to UNDEF
handling of co-processor #0/#1 instructions issued from user space
running in Thumb2 mode.
The PJ4 cores are used in four platforms: Armada 370/xp, Dove (Cubox,
d2plug), MMP2 (xo-1.75) and Berlin (Google TV). Out of these, only the
first is still widely used, but that one actually doesn't have iWMMXt
but instead has only VFPV3-D16, and so it is not impacted by this
change.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218427 [0]
Fixes: 8bcba70cb5c22 ("ARM: entry: Disregard Thumb undef exception ...")
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Reviewed-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
DT node names should be generic, so replace "weim" node name with
"memory-controller" in all i.MX SoC DT files.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The canonical node name for touchscreens is "touchscreen",
so update the i.MX6UL "tsc" node accordingly.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Replace all "xnur-gpio" with "xnur-gpios" in the i.MX6UL(L) Touchscreen
node, since the -gpio suffix is deprecated. All known implementations of
this binding can handle -gpio and -gpios since day 1, so this should be
fully backwards compatible.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
fsl,anatop should only be added to the usbphy nodes.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
pinctrl node name must be either pinctrl or pinmux.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Per davicom,dm9000.yaml, the Ethernet node name should be 'ethernet'.
Change it to fix the following schema warning:
imx1-apf9328.dtb: eth@4,c00000: $nodename:0: 'eth@4,c00000' does not match '^ethernet(@.*)?$'
from schema $id: http://devicetree.org/schemas/net/davicom,dm9000.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Per at24.yaml, the node name should be 'eeprom'.
Change it accordingly to fix the following schema warning:
imx28-evk.dtb: at24@51: $nodename:0: 'at24@51' does not match '^eeprom@[0-9a-f]{1,2}$'
from schema $id: http://devicetree.org/schemas/eeprom/at24.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable USB3 HW LPM feature.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This fixes the display not working on colibri imx7, the driver fails to
load with the following error:
mxsfb 30730000.lcdif: error -ENODEV: Cannot connect bridge
NXP i.MX7 LCDIF is connected to both the Parallel LCD Display and to a
MIPI DSI IP block, currently it's not possible to describe the
connection to both.
Remove the port endpoint from the SOC dtsi to prevent regressions, this
would need to be defined on the board DTS.
Reported-by: Hiago De Franco <hiagofranco@gmail.com>
Closes: https://lore.kernel.org/r/34yzygh3mbwpqr2re7nxmhyxy3s7qmqy4vhxvoyxnoguktriur@z66m7gvpqlia/
Fixes: edbbae7fba49 ("ARM: dts: imx7: add MIPI-DSI support")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
We identified that the PHYs actually do not work since commit 7da7b84fee58
("ARM: dts: imx6dl-yapp4: Move phy reset into switch node") as
a coincidence of several circumstances.
The reset signal is kept asserted by a pull-down resistor on the board
unless it is deasserted by GPIO from the SoC. This is to keep the switch
dead until it is configured properly by the kernel and user space.
Prior to the referenced commit the switch was reset by the FEC driver
and the reset GPIO was actively deasserted. The mdio-bus was scanned
and the attached switch and its PHYs were found and configured.
With the referenced commit the switch is reset by the qca8k driver.
Because of another bug in the qca8k driver, functionality of the reset
pin depends on its pre-kernel configuration. See commit c44fc98f0a8f
("net: dsa: qca8k: fix illegal usage of GPIO")
The problem did not appear until we removed support for the switch
and configuration of its reset pin from the bootloader.
To fix that, properly describe the internal mdio-bus configuration of
the qca8334 switch. The PHYs are internal to the switch and sit on its
internal mdio-bus.
Fixes: 7da7b84fee58 ("ARM: dts: imx6dl-yapp4: Move phy reset into switch node")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This change does not have any functional effect. The switch works just
fine without this patch as it has full access to all the addresses
on the bus. This is simply a clean-up to set the node name address
and reg address to the same value.
Fixes: 15b43e497ffd ("ARM: dts: imx6dl-yapp4: Use correct pseudo PHY address for the switch")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This is no-op.
FRAME_POINTER is defined in lib/Kconfig.debug.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
The common pattern in arm is to emit a "8<--- cut here ---" line for
faults, but it was missing for do_PrefetchAbort(). Add it.
Cc: Wang Kefeng <wangkefeng.wang@huawei.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Under PAN emulation when dumping backtraces from things like the
LKDTM EXEC_USERSPACE test[1], a double fault (which would hang a CPU)
would happen because of dump_instr() attempting to read a userspace
address. Make sure copy_from_kernel_nofault() does not attempt this
any more.
Closes: https://lava.sirena.org.uk/scheduler/job/497571
Link: https://lore.kernel.org/all/202401181125.D48DCB4C@keescook/ [1]
Reported-by: Mark Brown <broonie@kernel.org>
Suggested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Mark Brown <broonie@kernel.org>
Cc: Wang Kefeng <wangkefeng.wang@huawei.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Every other architecture in Linux includes the line "Call trace:" before
backtraces. In some cases ARM would print "Backtrace:", but this was
only via 1 specific call path, and wasn't included in CPU Oops nor things
like KASAN, UBSAN, etc that called dump_stack(). Regularize this line
so CI systems and other things (like LKDTM) that depend on parsing
"Call trace:" out of dmesg will see it for ARM.
Before this patch:
UBSAN: array-index-out-of-bounds in ../drivers/misc/lkdtm/bugs.c:376:16
index 8 is out of range for type 'char [8]'
CPU: 0 PID: 1402 Comm: cat Not tainted 6.7.0-rc2 #1
Hardware name: Generic DT based system
dump_backtrace from show_stack+0x20/0x24
r7:00000042 r6:00000000 r5:60070013 r4:80cf5d7c
show_stack from dump_stack_lvl+0x88/0x98
dump_stack_lvl from dump_stack+0x18/0x1c
r7:00000042 r6:00000008 r5:00000008 r4:80fab118
dump_stack from ubsan_epilogue+0x10/0x3c
ubsan_epilogue from __ubsan_handle_out_of_bounds+0x80/0x84
...
After this patch:
UBSAN: array-index-out-of-bounds in ../drivers/misc/lkdtm/bugs.c:376:16
index 8 is out of range for type 'char [8]'
CPU: 0 PID: 1402 Comm: cat Not tainted 6.7.0-rc2 #1
Hardware name: Generic DT based system
Call trace:
dump_backtrace from show_stack+0x20/0x24
r7:00000042 r6:00000000 r5:60070013 r4:80cf5d7c
show_stack from dump_stack_lvl+0x88/0x98
dump_stack_lvl from dump_stack+0x18/0x1c
r7:00000042 r6:00000008 r5:00000008 r4:80fab118
dump_stack from ubsan_epilogue+0x10/0x3c
ubsan_epilogue from __ubsan_handle_out_of_bounds+0x80/0x84
...
Link: https://lore.kernel.org/r/20240110215554.work.460-kees@kernel.org
Reported-by: Mark Brown <broonie@kernel.org>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Vladimir Murzin <vladimir.murzin@arm.com>
Cc: Zhen Lei <thunder.leizhen@huawei.com>
Cc: Keith Packard <keithpac@amazon.com>
Cc: Haibo Li <haibo.li@mediatek.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Change the "/**" beginning of comment to the common "/*" comment
since the comment is not in kernel-doc format. This prevents a
kernel-doc warning:
arch/arm/mm/init.c:422: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* update_sections_early intended to be called only through stop_machine
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: patches@armlinux.org.uk
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Nathan reported below building error:
=====
$ curl -LSso .config https://git.alpinelinux.org/aports/plain/community/linux-edge/config-edge.armv7
$ make -skj"$(nproc)" ARCH=arm CROSS_COMPILE=arm-linux-gnueabi- olddefconfig all
..
arm-linux-gnueabi-ld: arch/arm/kernel/machine_kexec.o: in function `arch_crash_save_vmcoreinfo':
machine_kexec.c:(.text+0x488): undefined reference to `vmcoreinfo_append_str'
====
On architecutres, like arm, s390, ppc, sh, function
arch_crash_save_vmcoreinfo() is located in machine_kexec.c and it can
only be compiled in when CONFIG_KEXEC_CORE=y.
That's not right because arch_crash_save_vmcoreinfo() is used to export
arch specific vmcoreinfo. CONFIG_VMCORE_INFO is supposed to control its
compiling in. However, CONFIG_VMVCORE_INFO could be independent of
CONFIG_KEXEC_CORE, e.g CONFIG_PROC_KCORE=y will select CONFIG_VMVCORE_INFO.
Or CONFIG_KEXEC/CONFIG_KEXEC_FILE is set while CONFIG_CRASH_DUMP is
not set, it will report linking error.
So, on arm, s390, ppc and sh, move arch_crash_save_vmcoreinfo out to
a new file vmcore_info.c. Let CONFIG_VMCORE_INFO decide if compiling in
arch_crash_save_vmcoreinfo().
[akpm@linux-foundation.org: remove stray newlines at eof]
Link: https://lkml.kernel.org/r/20240129135033.157195-3-bhe@redhat.com
Signed-off-by: Baoquan He <bhe@redhat.com>
Reported-by: Nathan Chancellor <nathan@kernel.org>
Closes: https://lore.kernel.org/all/20240126045551.GA126645@dev-arch.thelio-3990X/T/#u
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Hari Bathini <hbathini@linux.ibm.com>
Cc: Klara Modin <klarasmodin@gmail.com>
Cc: Michael Kelley <mhklinux@outlook.com>
Cc: Pingfan Liu <piliu@redhat.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Now crash codes under kernel/ folder has been split out from kexec
code, crash dumping can be separated from kexec reboot in config
items on arm with some adjustments.
Here use CONFIG_CRASH_RESERVE ifdef to replace CONFIG_KEXEC ifdef.
Link: https://lkml.kernel.org/r/20240124051254.67105-14-bhe@redhat.com
Signed-off-by: Baoquan He <bhe@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Hari Bathini <hbathini@linux.ibm.com>
Cc: Pingfan Liu <piliu@redhat.com>
Cc: Klara Modin <klarasmodin@gmail.com>
Cc: Michael Kelley <mhklinux@outlook.com>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
clang-16 warns about casting between incompatible function types:
arch/arm/crypto/sha256_glue.c:37:5: error: cast from 'void (*)(u32 *, const void *, unsigned int)' (aka 'void (*)(unsigned int *, const void *, unsigned int)') to 'sha256_block_fn *' (aka 'void (*)(struct sha256_state *, const unsigned char *, int)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
37 | (sha256_block_fn *)sha256_block_data_order);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/arm/crypto/sha512-glue.c:34:3: error: cast from 'void (*)(u64 *, const u8 *, int)' (aka 'void (*)(unsigned long long *, const unsigned char *, int)') to 'sha512_block_fn *' (aka 'void (*)(struct sha512_state *, const unsigned char *, int)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
34 | (sha512_block_fn *)sha512_block_data_order);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fix the prototypes for the assembler functions to match the typedef.
The code already relies on the digest being the first part of the
state structure, so there is no change in behavior.
Fixes: c80ae7ca3726 ("crypto: arm/sha512 - accelerated SHA-512 using ARM generic ASM and NEON")
Fixes: b59e2ae3690c ("crypto: arm/sha256 - move SHA-224/256 ASM/NEON implementation to base layer")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
If a bootloader does not configure the MAC address, devices come up with
a random MAC at the moment.
ocotp provides registers for storing the mac-address.
Configure those for i.MX6UL and i.MX6ULL allows net/core to retrieve it from
there.
Signed-off-by: Manuel Traut <manuel.traut@mt.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The USB PHY in the Allwinner R40 SoC seems to rely on voltage on the
VCC-TVIN/OUT supply pins for proper operation, on top of its own supply
voltage on VCC-USB. Without a 3.3V voltage supplied to VCC-TV*, USB
operation becomes unstable and can result in disconnects.
The Forlinx FETA40i-C SoM connects both the VCC-TVOUT and VCC-TVIN pins
to the ALDO1 rail of the PMIC, so we need to enable that rail for USB
operation. Since there is no supply property in the DT bindings for
the USB core, we need to always enable the regulator.
This fixes unstable USB operation on boards using the Forlinx FETA40i-C
module.
Signed-off-by: Fuyao Kashizuku <fuyao@sjterm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/ZYqRZev1g_mztff2@debian.cyg
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
|
|
Add sama7g5 flexcom specific compatible in DT with fallbacks.
Signed-off-by: Balakrishnan Sambath <balakrishnan.s@microchip.com>
Link: https://lore.kernel.org/r/20240223-b4-sama5d2-flexcom-yaml-v2-1-7e96c60c7701@microchip.com
[claudiu.beznea: adapt for flexcom10]
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
|
|
Align dmas to the opening '<' to comply with the dts coding style,
indentation section, point 3: "For arrays spanning across lines, it is
preferred to align the continued entries with opening < from the first
line."
Link: https://lore.kernel.org/r/20240218151353.3612621-3-claudiu.beznea@tuxon.dev
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
|
|
Align dmas to the opening '<' to comply with the dts coding style,
indentation section, point 3: "For arrays spanning across lines, it is
preferred to align the continued entries with opening < from the first
line."
Link: https://lore.kernel.org/r/20240218151353.3612621-2-claudiu.beznea@tuxon.dev
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
|
|
Add initial device tree of the SAMA7G54 Curiosity board.
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
Link: https://lore.kernel.org/r/20240215091524.14732-4-mihai.sain@microchip.com
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
|
|
Add flexcom 10 node for usage on the SAMA7G54 Curiosity board.
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
Link: https://lore.kernel.org/r/20240215091524.14732-3-mihai.sain@microchip.com
[claudiu.beznea: align dmas to the opening '<']
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
|
|
The only difference made by CONFIG_THERMAL_WRITABLE_TRIPS is whether or
not the writable trips mask passed during thermal zone registration
will take any effect, but whoever passes a non-zero writable trips mask
to thermal_zone_device_register_with_trips() can be forgiven thinking
that it will always work.
Moreover, some thermal drivers expect user space to set trip temperature
values, so they select CONFIG_THERMAL_WRITABLE_TRIPS, possibly overriding
a manual choice to unset it and going against the design purportedly
allowing system integrators to decide on the writability of trip points
for the given kernel build. It is also set in one platform's defconfig.
Forthermore, CONFIG_THERMAL_WRITABLE_TRIPS only affects trip temperature,
because trip hysteresis is writable as long as the thermal zone provides
a callback to update it, regardless of the CONFIG_THERMAL_WRITABLE_TRIPS
value.
The above means that the symbol in question is used inconsistently and
its purpose is at least moot, so remove it and always take the writable
trip mask passed to thermal_zone_device_register_with_trips() into
account.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/fixes
Renesas fixes for v6.8
- Add missing #interrupt-cells to DA9063 nodes.
* tag 'renesas-fixes-for-v6.8-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
ARM: dts: renesas: rcar-gen2: Add missing #interrupt-cells to DA9063 nodes
Link: https://lore.kernel.org/r/cover.1708597150.git.geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add support for the MCIMXHDMICARD expansion card attached to the iMX53
QSB / QSRB platforms. This enables HDMI output on those devices.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Since commit bfac19e239a7 ("fbdev: mx3fb: Remove the driver") backlight
is no longer functional.
The fbdev mx3fb driver used to automatically select
CONFIG_BACKLIGHT_CLASS_DEVICE.
Now that the mx3fb driver has been removed, enable the
CONFIG_BACKLIGHT_CLASS_DEVICE option so that backlight can still work
by default.
Tested on a imx6dl-sabresd board.
Cc: stable@vger.kernel.org
Fixes: bfac19e239a7 ("fbdev: mx3fb: Remove the driver")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Tested-by: Francesco Dolcini <francesco.dolcini@toradex.com> # Toradex Colibri iMX7
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Now that the minimum supported version of LLVM for building the kernel has
been bumped to 13.0.1, the conditional expression added to get_current()
by commit c1e42efacb9b ("ARM: 9151/1: Thumb2: avoid
__builtin_thread_pointer() on Clang") is always true, as the build will
fail during the configuration stage for older LLVM versions. Remove it,
effectively reverting the aforementioned change.
Link: https://lkml.kernel.org/r/20240125-bump-min-llvm-ver-to-13-0-1-v1-4-f5ff9bda41c5@kernel.org
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: "Aneesh Kumar K.V (IBM)" <aneesh.kumar@kernel.org>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Borislav Petkov (AMD) <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Conor Dooley <conor@kernel.org>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: "Naveen N. Rao" <naveen.n.rao@linux.ibm.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Nicolas Schier <nicolas@fjasle.eu>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Introduce a generic way to query whether the data cache is virtually
aliased on all architectures. Its purpose is to ensure that subsystems
which are incompatible with virtually aliased data caches (e.g. FS_DAX)
can reliably query this.
For data cache aliasing, there are three scenarios dependending on the
architecture. Here is a breakdown based on my understanding:
A) The data cache is always aliasing:
* arc
* csky
* m68k (note: shared memory mappings are incoherent ? SHMLBA is missing there.)
* sh
* parisc
B) The data cache aliasing is statically known or depends on querying CPU
state at runtime:
* arm (cache_is_vivt() || cache_is_vipt_aliasing())
* mips (cpu_has_dc_aliases)
* nios2 (NIOS2_DCACHE_SIZE > PAGE_SIZE)
* sparc32 (vac_cache_size > PAGE_SIZE)
* sparc64 (L1DCACHE_SIZE > PAGE_SIZE)
* xtensa (DCACHE_WAY_SIZE > PAGE_SIZE)
C) The data cache is never aliasing:
* alpha
* arm64 (aarch64)
* hexagon
* loongarch (but with incoherent write buffers, which are disabled since
commit d23b7795 ("LoongArch: Change SHMLBA from SZ_64K to PAGE_SIZE"))
* microblaze
* openrisc
* powerpc
* riscv
* s390
* um
* x86
Require architectures in A) and B) to select ARCH_HAS_CPU_CACHE_ALIASING and
implement "cpu_dcache_is_aliasing()".
Architectures in C) don't select ARCH_HAS_CPU_CACHE_ALIASING, and thus
cpu_dcache_is_aliasing() simply evaluates to "false".
Note that this leaves "cpu_icache_is_aliasing()" to be implemented as future
work. This would be useful to gate features like XIP on architectures
which have aliasing CPU dcache-icache but not CPU dcache-dcache.
Use "cpu_dcache" and "cpu_cache" rather than just "dcache" and "cache"
to clarify that we really mean "CPU data cache" and "CPU cache" to
eliminate any possible confusion with VFS "dentry cache" and "page
cache".
Link: https://lore.kernel.org/lkml/20030910210416.GA24258@mail.jlokier.co.uk/
Link: https://lkml.kernel.org/r/20240215144633.96437-9-mathieu.desnoyers@efficios.com
Fixes: d92576f1167c ("dax: does not work correctly with virtual aliasing caches")
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: kernel test robot <lkp@intel.com>
Cc: Michael Sclafani <dm-devel@lists.linux.dev>
Cc: Mike Snitzer <snitzer@kernel.org>
Cc: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Let's use our handy helper now that it's available on all archs.
Link: https://lkml.kernel.org/r/20240129124649.189745-10-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Tested-by: Ryan Roberts <ryan.roberts@arm.com>
Reviewed-by: Mike Rapoport (IBM) <rppt@kernel.org>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Alexandre Ghiti <alexghiti@rivosinc.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: David S. Miller <davem@davemloft.net>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Naveen N. Rao <naveen.n.rao@linux.ibm.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Russell King (Oracle) <linux@armlinux.org.uk>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
We want to make use of pte_next_pfn() outside of set_ptes(). Let's simply
define PFN_PTE_SHIFT, required by pte_next_pfn().
Link: https://lkml.kernel.org/r/20240129124649.189745-3-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Tested-by: Ryan Roberts <ryan.roberts@arm.com>
Reviewed-by: Mike Rapoport (IBM) <rppt@kernel.org>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Alexandre Ghiti <alexghiti@rivosinc.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: David S. Miller <davem@davemloft.net>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Naveen N. Rao <naveen.n.rao@linux.ibm.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Russell King (Oracle) <linux@armlinux.org.uk>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Patch series "mm: ptdump: Refactor CONFIG_DEBUG_WX and check_wx_pages
debugfs attribute", v2.
This series refactors CONFIG_DEBUG_WX for the 5 architectures implementing
CONFIG_GENERIC_PTDUMP
First rename stuff in ARM which uses similar names while not implementing
CONFIG_GENERIC_PTDUMP.
Then define a generic version of debug_checkwx() that calls
ptdump_check_wx() when CONFIG_DEBUG_WX is set. Call it immediately after
calling mark_rodata_ro() instead of calling it at the end of every
mark_rodata_ro().
Then implement a debugfs attribute that can be used to trigger a W^X test
at anytime and regardless of CONFIG_DEBUG_WX
This patch (of 5):
CONFIG_DEBUG_WX is a core option defined in mm/Kconfig.debug
To avoid any future conflict, rename ARM version into CONFIG_ARM_DEBUG_WX.
Link: https://lore.kernel.org/lkml/20200422152656.GF676@willie-the-truck/T/#m802eaf33efd6f8d575939d157301b35ac0d4a64f
Link: https://github.com/KSPP/linux/issues/35
Link: https://lkml.kernel.org/r/cover.1706610398.git.christophe.leroy@csgroup.eu
Link: https://lkml.kernel.org/r/fa297aa90caeb61eee2b70c6c5897a2ab58a9562.1706610398.git.christophe.leroy@csgroup.eu
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: "Aneesh Kumar K.V (IBM)" <aneesh.kumar@kernel.org>
Cc: Borislav Petkov (AMD) <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Cc: Greg KH <greg@kroah.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: "Naveen N. Rao" <naveen.n.rao@linux.ibm.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Phong Tran <tranmanphong@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Steven Price <steven.price@arm.com>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Alexandre Ghiti <alexghiti@rivosinc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Add device-tree for LG Optimus 4X HD P880, which is a NVIDIA
Tegra30-based smartphone, originally running Android.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add device-tree for LG Optimus Vu P895, which is a NVIDIA
Tegra30-based smartphone, originally running Android.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
A recent rt5640 codec update requires mclk definition in the
device tree. Without mclk defined sound will not work.
Signed-off-by: Robert Eckelmann <longnoserob@gmail.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Sound Driver requires "reg-names" to get register info. Current driver
tries to get register info via "reg" instead of "reg-names" as backup
plan, but this support will be removed soon.
Use "reg-namess" for r8a7778 sound.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/87cyszpwmp.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|