| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Add SFP module support for Clearfog using the SFP phylink support.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
All the devices on I2C0 support fast mode, so increase the bus speed
to match. The Armada 388 is known to have a timing issue when in
standard mode, which we believe causes the ficticious device at 0x64
to appear.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Move the uart nodes over to use the label form to reference the serial
devices, rather than replicating the device node path.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Move the ethernet, buffer manager, and mdio nodes over to use label form
to reference the devices rather than replicating the device path.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Move the I2C nodes over to use the label form to reference the I2C
controllers, rather than replicating the device node path.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Move the device specific pinctrl nodes over to use the label form to
reference the pin mux controller, rather than replicating the device
node path.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Add the DTS file to describe the clearfog pro model - we update the
platform name and compatible string compared to the original version.
The original version remains for compatibility for the time being as
the name of the file has become established, and the machine name
and/or compatible may be used by userspace.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Add the DTS file to describe the clearfog base model.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Move the rear button support into the clearfog pro support file.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Move the SPI CS1 configuration to the clearfog .dts file as this is only
present on pro models.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Move the second PCIe port to the clearfog .dts file as this is only
present on the pro models.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Move the DSA switch configuration to the clearfog .dts file as this is
only present on the pro models.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
There are two versions of the clearfog - a base and a pro model. The
base model has an additional PHY on eth1, replacing the DSA switch on
the pro model. MPP assignments are slightly different. The base model
also omits the second PCIe, and footprint for a PIC microcontroller.
In order to cater for these differences, move all the existing clearfog
support to a dtsi file before starting to modify it, to make the
following changes more clear.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Move the SDHCI pinctrl node to the microsom file - the microsom can have
optional eMMC support which uses these same pinctrl settings, so it is
sensible to have these here.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
The optional SPI flash is fitted to the microsom, not the clearfog
board, so it should be specified in the microsom DTS include file.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
The SPI flash #size-cells is specified in the binding documentation to
have value 1, but we were setting it to zero. This wasn't causing any
problem as we do not list any partitions, but it's worth specifying
correctly if we're going to specify it at all.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Final batch of SoC fixes
A few fixes that have trickled in over the last week, all fixing minor
errors in devicetrees -- UART pin assignment on Allwinner H3,
correcting number of SATA ports on a Marvell-based Linkstation
platform and a display clock fix for Freescale/NXP i.MX7D that fixes a
freeze when starting up X"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: orion5x: fix number of sata port for linkstation ls-gl
ARM: dts: imx7d: fix LCDIF clock assignment
dts: sun8i-h3: correct UART3 pin definitions
|
|
Bug report from Debian [0] shows there's minor changed model of
Linkstation LS-GL that uses the 2nd SATA port of the SoC.
So it's necessary to enable two SATA ports, though for that specific
model only the 2nd one is used.
[0] https://bugs.debian.org/845611
Fixes: b1742ffa9ddb ("ARM: dts: orion5x: add device tree for buffalo linkstation ls-gl")
Reported-by: Ryan Tandy <ryan@nardis.ca>
Tested-by: Ryan Tandy <ryan@nardis.ca>
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The eLCDIF IP of the i.MX 7 SoC knows multiple clocks and lists them
separately:
Clock Clock Root Description
apb_clk MAIN_AXI_CLK_ROOT AXI clock
pix_clk LCDIF_PIXEL_CLK_ROOT Pixel clock
ipg_clk_s MAIN_AXI_CLK_ROOT Peripheral access clock
All of them are switched by a single gate, which is part of the
IMX7D_LCDIF_PIXEL_ROOT_CLK clock. Hence using that clock also for
the AXI bus clock (clock-name "axi") makes sure the gate gets
enabled when accessing registers.
There seem to be no separate AXI display clock, and the clock is
optional. Hence remove the dummy clock.
This fixes kernel freezes when starting the X-Server (which
disables/re-enables the display controller).
Fixes: e8ed73f691bd ("ARM: dts: imx7d: add lcdif support")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
In a previous commit, I made a copy/paste error in the pinmux
definitions of UART3: PG{13,14} instead of PA{13,14}. This commit takes
care of that. I have tested this commit on Orange Pi PC and Orange Pi
Plus, and it works for these boards.
Fixes: e3d11d3c45c5 ("dts: sun8i-h3: add pinmux definitions for
UART2-3")
Signed-off-by: Jorik Jonker <jorik@kippendief.biz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"This should be the last set of bugfixes for arm-soc in v4.9. None of
these are critical regressions, but it would be nice to still get them
merged.
- On the Juno platform, the idle latency was described wrong, leading
to suboptimal cpuidle tuning.
- Also on the same platform, PCI I/O space was set up incorrectly and
could not work.
- On the sti platform, a syntactically incorrect DT entry caused
warnings.
- The newly added 'gr8' platform has somewhat confusing file names,
which we rename for consistency"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: dts: juno: fix cluster sleep state entry latency on all SoC versions
arm64: dts: juno: Correct PCI IO window
ARM: dts: STiH407-family: fix i2c nodes
ARM: gr8: Rename the DTSI and relevant DTS
|
|
Pull ARM fix from Russell King:
"This resolves the ksyms issues by reverting the commit which
introduced the breakage"
There was what I consider to be a better fix, but it's late in the rc
game, so I'll take the revert.
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
Revert "arm: move exports to definitions"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti into fixes
Pull "STi DT fix" from Patrice Chotard:
The I2C nodes are missing #address-cells and #size-cells.
This is causing warning at device tree compilation when
some I2C device sub-nodes are defined.
* tag 'sti-dt-for-v4.9-rc-round2' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti:
ARM: dts: STiH407-family: fix i2c nodes
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Pull "Allwinner fixes for 4.9, second iteration" from Maxime Ripard:
A renaming of the GR8 DTSI and DTS to make it explicitly part of the sun5i
family.
* tag 'sunxi-fixes-for-4.9-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: gr8: Rename the DTSI and relevant DTS
|
|
This reverts commit 4dd1837d7589f468ed109556513f476e7a7f9121.
Moving the exports for assembly code into the assembly files breaks
KSYM trimming, but also breaks modversions.
While fixing the KSYM trimming is trivial, fixing modversions brings
us to a technically worse position that we had prior to the above
change:
- We end up with the prototype definitions divorsed from everything
else, which means that adding or removing assembly level ksyms
become more fragile:
* if adding a new assembly ksyms export, a missed prototype in
asm-prototypes.h results in a successful build if no module in
the selected configuration makes use of the symbol.
* when removing a ksyms export, asm-prototypes.h will get forgotten,
with armksyms.c, you'll get a build error if you forget to touch
the file.
- We end up with the same amount of include files and prototypes,
they're just in a header file instead of a .c file with their
exports.
As for lines of code, we don't get much of a size reduction:
(original commit)
47 files changed, 131 insertions(+), 208 deletions(-)
(fix for ksyms trimming)
7 files changed, 18 insertions(+), 5 deletions(-)
(two fixes for modversions)
1 file changed, 34 insertions(+)
3 files changed, 7 insertions(+), 2 deletions(-)
which results in a net total of only 25 lines deleted.
As there does not seem to be much benefit from this change of approach,
revert the change.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
The I2C nodes are missing #address-cells and #size-cells. This is
causing warning at device tree compilation when some I2C device
sub-nodes are defined.
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
|
|
Reviews have found that sun5i was a better prefix after all for the GR8.
Rename the relevant device trees before it's too late.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Pull ARM fixes from Russell King:
"A few more ARM fixes:
- the assembly backtrace code suffers problems with the new printk()
implementation which assumes that kernel messages without KERN_CONT
should have newlines inserted between them. Fix this.
- fix a section naming error - ".init.text" rather than ".text.init"
- preallocate DMA debug memory at core_initcall() time rather than
fs_initcall(), as we have some core drivers that need to use DMA
mapping - and that triggers a kernel warning from the DMA debug
code.
- fix XIP kernels after the ro_after_init changes made this data
permanently read-only"
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: Fix XIP kernels
ARM: 8628/1: dma-mapping: preallocate DMA-debug hash tables in core_initcall
ARM: 8624/1: proc-v7m.S: fix init section name
ARM: fix backtrace
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Allwinner fixes for 4.9
A fix to reintroduce missing pinmux options that turned out not to be
optional.
* tag 'sunxi-fixes-for-4.9' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: dts: sun8i: fix the pinmux for UART1
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti into fixes
STi DT fix:
Fix typo cs-gpio to cs-gpios
* tag 'sti-dt-for-v4.9-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti:
ARM: dts: STiH410-b2260: Fix typo in spi0 chipselect definition
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.9, 2nd round:
It fixes a boot failure on imx53-qsb board with a DA9053 PMIC, which is
caused by the regulator core change, commit fa93fd4ecc9c ("regulator:
core: Ensure we are at least in bounds for our constraints").
* tag 'imx-fixes-4.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx53-qsb: Fix regulator constraints
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for v4.9-rc cycle. Except for the omap3 fix for the SoC
features printed, all these are quite trivial and tiny. The omap5 jack
detection and gpadc patches are not strictly fixes, but I wanted to get
binding document typo fixed before it pops up on other boards. The
gpadc one liner was in the same series and I applied and pushed it out
already before noticing it could have waited. The list of changes is:
- Fix omap3 SoC features printed
- Make sure OMAP_INTERCONNECT is selected for am43xx only configurations
- Add missing memory node for torpedo
- Initialize uart4_mask properly to avoid writing garbage to PRM registers
- Fix NULL pointer dereference for omap4 volt_data
- Add alias for omap5 gpadc needed by iio drivers
- Enable omap5 jack headset jack detection and fix it's binding typo
- Add missing memory node for logicpd-som-lv
- Fix wrong SMPS6 voltage for VDD-DDR3 for omap5
* tag 'omap-for-v4.9/fixes-for-rc-cycle' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap5: board-common: fix wrong SMPS6 (VDD-DDR3) voltage
ARM: omap3: Add missing memory node in SOM-LV
ASoC: omap-abe-twl6040: fix typo in bindings documentation
dts: omap5: board-common: enable twl6040 headset jack detection
dts: omap5: board-common: add phandle to reference Palmas gpadc
ARM: OMAP2+: avoid NULL pointer dereference
ARM: OMAP2+: PRM: initialize en_uart4_mask and grpsel_uart4_mask
ARM: dts: omap3: Fix memory node in Torpedo board
ARM: AM43XX: Select OMAP_INTERCONNECT in Kconfig
ARM: OMAP3: Fix formatting of features printed
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Commit 7619751f8c90 ("ARM: 8595/2: apply more __ro_after_init") caused
a regression with XIP kernels by moving the __ro_after_init data into
the read-only section. With XIP kernels, the read-only section is
located in read-only memory from the very beginning.
Work around this by moving the __ro_after_init data back into the .data
section, which will be in RAM, and hence will be writable.
It should be noted that in doing so, this remains writable after init.
Fixes: 7619751f8c90 ("ARM: 8595/2: apply more __ro_after_init")
Reported-by: Andrea Merello <andrea.merello@gmail.com>
Tested-by: Andrea Merello <andrea.merello@gmail.com> [ XIP stm32 ]
Tested-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
fs_initcall is definitely too late to initialize DMA-debug hash tables,
because some drivers might get probed and use DMA mapping framework
already in core_initcall. Late initialization of DMA-debug results in
false warning about accessing memory, that was not allocated, like this
one:
------------[ cut here ]------------
WARNING: CPU: 5 PID: 1 at lib/dma-debug.c:1104 check_unmap+0xa1c/0xe50
exynos-sysmmu 10a60000.sysmmu: DMA-API: device driver tries to free DMA memory it has not allocated [device
address=0x000000006ebd0000] [size=16384 bytes]
Modules linked in:
CPU: 5 PID: 1 Comm: swapper/0 Not tainted 4.9.0-rc5-00028-g39dde3d-dirty #44
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[<c0119dd4>] (unwind_backtrace) from [<c01122bc>] (show_stack+0x20/0x24)
[<c01122bc>] (show_stack) from [<c062714c>] (dump_stack+0x84/0xa0)
[<c062714c>] (dump_stack) from [<c0132560>] (__warn+0x14c/0x180)
[<c0132560>] (__warn) from [<c01325dc>] (warn_slowpath_fmt+0x48/0x50)
[<c01325dc>] (warn_slowpath_fmt) from [<c06814f8>] (check_unmap+0xa1c/0xe50)
[<c06814f8>] (check_unmap) from [<c06819c4>] (debug_dma_unmap_page+0x98/0xc8)
[<c06819c4>] (debug_dma_unmap_page) from [<c076c3e8>] (exynos_iommu_domain_free+0x158/0x380)
[<c076c3e8>] (exynos_iommu_domain_free) from [<c0764a30>] (iommu_domain_free+0x34/0x60)
[<c0764a30>] (iommu_domain_free) from [<c011f168>] (release_iommu_mapping+0x30/0xb8)
[<c011f168>] (release_iommu_mapping) from [<c011f23c>] (arm_iommu_release_mapping+0x4c/0x50)
[<c011f23c>] (arm_iommu_release_mapping) from [<c0b061ac>] (s5p_mfc_probe+0x640/0x80c)
[<c0b061ac>] (s5p_mfc_probe) from [<c07e6750>] (platform_drv_probe+0x70/0x148)
[<c07e6750>] (platform_drv_probe) from [<c07e25c0>] (driver_probe_device+0x12c/0x6b0)
[<c07e25c0>] (driver_probe_device) from [<c07e2c6c>] (__driver_attach+0x128/0x17c)
[<c07e2c6c>] (__driver_attach) from [<c07df74c>] (bus_for_each_dev+0x88/0xc8)
[<c07df74c>] (bus_for_each_dev) from [<c07e1b6c>] (driver_attach+0x34/0x58)
[<c07e1b6c>] (driver_attach) from [<c07e1350>] (bus_add_driver+0x18c/0x32c)
[<c07e1350>] (bus_add_driver) from [<c07e4198>] (driver_register+0x98/0x148)
[<c07e4198>] (driver_register) from [<c07e5cb0>] (__platform_driver_register+0x58/0x74)
[<c07e5cb0>] (__platform_driver_register) from [<c174cb30>] (s5p_mfc_driver_init+0x1c/0x20)
[<c174cb30>] (s5p_mfc_driver_init) from [<c0102690>] (do_one_initcall+0x64/0x258)
[<c0102690>] (do_one_initcall) from [<c17014c0>] (kernel_init_freeable+0x3d0/0x4d0)
[<c17014c0>] (kernel_init_freeable) from [<c116eeb4>] (kernel_init+0x18/0x134)
[<c116eeb4>] (kernel_init) from [<c010bbd8>] (ret_from_fork+0x14/0x3c)
---[ end trace dc54c54bd3581296 ]---
This patch moves initialization of DMA-debug to core_initcall. This is
safe from the initialization perspective. dma_debug_do_init() internally calls
debugfs functions and debugfs also gets initialised at core_initcall(), and
that is earlier than arch code in the link order, so it will get initialized
just before the DMA-debug.
Reported-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
There is no .text.init sections.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Recent kernels have changed their behaviour to be more inconsistent
when handling printk continuations. With todays kernels, the output
looks sane on the console, but dmesg splits individual printk()s which
do not have the KERN_CONT prefix into separate lines.
Since the assembly code is not trivial to add the KERN_CONT, and we
ideally want to avoid using KERN_CONT (as multiple printk()s can race
between different threads), convert the assembly dumping the register
values to C code, and have the C code build the output a line at a
time before dumping to the console.
This avoids the KERN_CONT issue, and also avoids situations where the
output is intermixed with other console activity.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Change cs-gpio to cs-gpios.
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
|
|
DDR3L is usually specified as
JEDEC standard 1.35V(1.28V~1.45V) & 1.5V(1.425V~1.575V)
Therefore setting smps6 regulator to 1.2V is definitively below
minimum. It appears that real world chips are more forgiving than
data sheets indicate, but let's set the regulator right.
Note: a board that uses other voltages (DDR with 1.5V) can
overwrite by referencing &smps6_reg.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/ARM updates for v4.9-rc4
- Kick the vcpu when a pending interrupt becomes pending again
- Prevent access to invalid interrupt registers
- Invalid TLBs when two vcpus from the same VM share a CPU
|
|
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e141 arm64: dts: kill skeleton.dtsi").
commit ("766a1fe78fc3 ARM: omap3: Add missing memory node") had
fixes for Torpedo and Overo boards, but this SOM-LV was missed.
This should help prevent the DTC warning:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Will be needed for iio based drivers.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
For OMAP4, volt_data is set in omap44xx_voltagedomains_init.
If the SoC is neither OMAP443X or OMAP446X, we end up with a
NULL in volt_data which causes a kernel oops.
This is the case when booting OMAP4470.
Signed-off-by: Nicolae Rosia <Nicolae_Rosia@mentor.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
In the case where has_uart4 is false, en_uart4_mask and grpsel_uart4_mask
are not initialized and so any garbage value is being logically or'd into
the write of PM_WKEN and OMAP3430_PM_MPUGRPSEL. Fix this by initializing
these masks to zero.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit ("766a1fe78fc3 ARM: omap3: Add missing memory node") added
the memory node, but the patch didn't have the correct starting address.
This patch fixes the correct starting address.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
AM437x makes use of the omap_l3_noc driver so explicitly select
OMAP_INTERCONNECT in the Kconfig for SOC_AM43XX to ensure it gets enabled
for AM43XX only builds.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
With the printk cleanups merged into v4.9-rc1, we now get the omap
revision printed on multiple lines. Let's fix that and also remove the
extra empty space at the end of the features. And let's update things
to use scnprintf as suggested by Ivaylo Dimitrov
<ivo.g.dimitrov.75@gmail.com>.
Reported-by: Adam Ford <aford173@gmail.com>
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Since commit fa93fd4ecc9c ("regulator: core: Ensure we are at least in
bounds for our constraints") the imx53-qsb board populated with a Dialog
DA9053 PMIC fails to boot:
LDO3: Bringing 3300000uV into 1800000-1800000uV
The LDO3 voltage constraints passed in the device tree do not match
the valid range according to the datasheet, so fix this accordingly to
allow the board booting again.
While at it, fix the other voltage constraints as well.
Cc: <stable@vger.kernel.org> # 4.7.x
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
