| Age | Commit message (Collapse) | Author |
|---|
|
For now, there wasn't any in-tree users of the dtsi files for the
Kontron SMARC-sAMX6i board. Let's add device trees, for this board on a
Kontron SMARC Eval 2.0 Carrier.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Remove the "wake-up-gpio" property within the PCIe controller node.
There is no such property, thus just remove it. This will also make the
schema validation happy.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The PCIe reset line is active low. Fix it.
Fixes: 2a51f9dae13d ("ARM: dts: imx6qdl-kontron-samx6i: Add iMX6-based Kontron SMARC-sAMX6i module")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Rename the nodes according to the schema. In particular, rename the bit
bang I2C controller to "i2c-N" and the mux nodes of the audmux to
"mux-*". While at it, fix the typo "adu", which should have been "aud".
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The module can enable/disable the SD card power supply and has
it's dedicated pin SDIO_PWR_EN for that reason. This is esp.
useful to be able to reset the SD card if it was in an UHS mode.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
There are no variants of this module without an eMMC.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The correct name of the product is "Kontron SMARC-sAMX6i". See also
https://www.kontron.com/en/products/smarc-samx6i/p89810
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
There is a comment in the imx6q variant dtsi claiming that these
modules will have one more chip select than the imx6dl variant.
This is wrong. Ordinary GPIOs are used for chip selects and both
variants of the module share the very same PCB and both have this
GPIO routed to the SPI0_CS1# pin of the SMARC connector.
Fix it by moving the third chip select description to the common dtsi.
Fixes: 2125212785c9 ("ARM: dts: imx6qdl-kontron-samx6i: add Kontron SMARC SoM Support")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Remove the comment, remove the unused phandle name for the
VGEN5 output. VGEN5 is not used at all.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
On i.MX6 the board is reset by the watchdog. But in turn to do a
complete board reset, we have to assert the WDOG_B output which is
routed also to the CPLD which then do a complete power-cycle of the
board.
Fixes: 2125212785c9 ("ARM: dts: imx6qdl-kontron-samx6i: add Kontron SMARC SoM Support")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The PHY reset line is connected to both the SoC (GPIO1_25) and
the CPLD. We must not use the GPIO1_25 as it will drive against
the output buffer of the CPLD. Instead there is another GPIO
(GPIO2_01), an input to the CPLD, which will tell the CPLD to
assert the PHY reset line.
Fixes: 2a51f9dae13d ("ARM: dts: imx6qdl-kontron-samx6i: Add iMX6-based Kontron SMARC-sAMX6i module")
Fixes: 5694eed98cca ("ARM: dts: imx6qdl-kontron-samx6i: move phy reset into phy-node")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The i.MX6 cannot add any RGMII delays. The PHY has to add both the RX
and TX delays on the RGMII interface. Fix the interface mode. While at
it, use the new phy-connection-type property name.
Fixes: 5694eed98cca ("ARM: dts: imx6qdl-kontron-samx6i: move phy reset into phy-node")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Use cleaner (and non-deprecated) bindings syntax. See commit
bd912c991d2e ("dt-bindings: nvmem: layouts: add fixed-layout") for
details.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
There is a ti,enable-id-detection property in the Extcon Palmas
(extcon-palmas), but not in the Extcon USB GPIO binding and driver.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202406152004.F2fNnorG-lkp@intel.com/
Link: https://lore.kernel.org/r/20240615174904.39012-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
|
DT schema expects panel timings node to follow certain pattern,
dtbs_check warnings:
am335x-pdu001.dtb: display-timings: '240x320p16' does not match any of the regexes: '^timing', 'pinctrl-[0-9]+'
Linux drivers do not care about node name, so this should not have
effect on Linux.
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> # For DaVinci
Link: https://lore.kernel.org/r/20240509104813.216655-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
|
Add regulators used by the framebuffer of Motorola Moto G 4G (2013).
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240617-peregrine-v2-3-c8835d2da7af@apitzsch.eu
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add alert interrupt for the temperature sensor of Motorola Moto G 4G
(2013), although not used by the driver yet.
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240617-peregrine-v2-2-c8835d2da7af@apitzsch.eu
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
regulator
Add the accelerometer, magnetometer and regulator that are present on
the Motorola Moto G 4G (2013) device.
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240617-peregrine-v2-1-c8835d2da7af@apitzsch.eu
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Enable the hdmi_sound node and add i2s0 as sound source
for mk808 hdmi.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/aa79ff87-ea94-4f6d-a81b-5110724243f4@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
On some devicetrees, the drive-strength property gets assigned a
MTK_DRIVE_(x)_mA definition, which matches with (x).
For example, MTK_DRIVE_8mA equals to 8 and MTK_DRIVE_30mA equals
to 30.
Also keeping in mind that the drive-strength property is, by
(binding) definition, taking a number in milliamperes unit,
change all devicetrees to avoid the usage of any MTK_DRIVE_(x)
definition.
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20240620101656.1096374-3-angelogioacchino.delregno@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
|
|
Drop auto-selecting the driver, so it can be built either as a module or
built-in.
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240620083115.204362-8-antonio.borneo@foss.st.com
|
|
With the smsm bindings and driver finally supporting mboxes, switch to
that and stop using apcs as syscon.
Signed-off-by: Luca Weiss <luca@lucaweiss.eu>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240619-smsm-mbox-dts-v1-1-268ab7eef779@lucaweiss.eu
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
SD cards would exhibit errors similar to ones described in commit
27fe0fc05f35 ("ARM: dts: msm8974-FP2: Increase load on l20 for sdhci")
This patch applies the same change to the regulator for sdhc2.
Signed-off-by: Valeriy Klimin <vdos63@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240621-sony-aries-v2-3-dddf10722522@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add the dts for the Z3 Compact. This is currently almost the same
as the plain Z3 as they share almost the same hardware and
nothing device-specific is currently supported.
Signed-off-by: Valeriy Klimin <vdos63@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240621-sony-aries-v2-2-dddf10722522@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add the Serial Flash Controller and it's pincontrols.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Link: https://lore.kernel.org/r/20240606143401.32454-7-knaerzche@gmail.com
[reference HCLK_SFC by its numeric id to prevent conflicts with the
clock binding/controller changes]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Use recommended generic node names for the Adreno GPU and QFPROM fused
values device nodes.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240623120707.45764-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add hdmi-sound node to rk3066a.dtsi, so that it
can be reused by boards with HDMI support.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/5fe7c2fe-4a38-436a-8017-66989959329a@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The SoC has a S/PDIF TX controller which is fully compatible with older
generation Rockchip SoCs.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Link: https://lore.kernel.org/r/20240506155103.206592-3-knaerzche@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
RK3128 SoCs have two i2s controllers. i2s_8ch has 8 tx and 2 rx channels
and is internally hard-wired to the hdmi-controller respectivly the SoC's
analog codec. i2s_2ch has 2 tx and 2 rx channels and can also be used
externally as it's pins are exposed though pinctrl.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Link: https://lore.kernel.org/r/20240506155103.206592-2-knaerzche@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add the Designware MIPI DSI controller and it's port nodes.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Link: https://lore.kernel.org/r/20240509140653.168591-8-knaerzche@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The InnoSilicon D-PHY found in RK3128 SoCs supports DSI/LVDS/TTL with a
maximum transfer rate of 1 Gbps per lane. While adding it, also add it's
clocks to RK3128_PD_VIO powerdomain as the phy is part of it.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Link: https://lore.kernel.org/r/20240509140653.168591-7-knaerzche@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Build the proper driver by selecting the appropriate config flag.
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240620083115.204362-3-antonio.borneo@foss.st.com
|
|
The standard node name for I2C buses is 'i2c'.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20240531193115.3814887-1-robh@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
|
The standard node name for I2C buses is 'i2c'.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20240531193104.3814663-1-robh@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
|
The watchdog appears to be an ARM SP805, add the full compatible
and the needed clocks properties. Leave this disabled for now
as functionality is not fully tested.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240612151314.27967-2-afd@ti.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
|
Fixes the following DTB check warning:
> node has a reg or ranges property, but no unit name
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240612151314.27967-1-afd@ti.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC fixes from Arnd Bergmann:
"There are seven oneline patches that each address a distinct problem
on the NXP i.MX platform, mostly the popular i.MX8M variant.
The only other two fixes are for error handling on the psci firmware
driver and SD card support on the milkv duo riscv board"
* tag 'arm-fixes-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
firmware: psci: Fix return value from psci_system_suspend()
riscv: dts: sophgo: disable write-protection for milkv duo
arm64: dts: imx8qm-mek: fix gpio number for reg_usdhc2_vmmc
arm64: dts: freescale: imx8mm-verdin: enable hysteresis on slow input pin
arm64: dts: imx93-11x11-evk: Remove the 'no-sdio' property
arm64: dts: freescale: imx8mp-venice-gw73xx-2x: fix BT shutdown GPIO
arm: dts: imx53-qsb-hdmi: Disable panel instead of deleting node
arm64: dts: imx8mp: Fix TC9595 input clock on DH i.MX8M Plus DHCOM SoM
arm64: dts: freescale: imx8mm-verdin: Fix GPU speed
|
|
The crc32/crc32c implementations using the scalar CRC32 instructions are
accessed via indirect calls, and so they must be annotated with type ids
in order to execute correctly when kCFI is enabled.
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Kees Cook <kees@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
With ARCH=arm, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in arch/arm/crypto/aes-arm-bs.o
WARNING: modpost: missing MODULE_DESCRIPTION() in arch/arm/crypto/crc32-arm-ce.o
Add the missing invocation of the MODULE_DESCRIPTION() macro to all
files which have a MODULE_LICENSE().
This includes crct10dif-ce-glue.c and curve25519-glue.c which,
although they did not produce a warning with the arm allmodconfig
configuration, may cause this warning with other configurations.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
With ARCH=arm, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in arch/arm/crypto/poly1305-arm.o
Add the missing invocation of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
In the combined DT of rk3066a/rk3188 the emac node uses as place holder
the compatible string "snps,arc-emac". The last real user nSIM_700
of the "snps,arc-emac" compatible string in a driver was removed in 2019.
Rockchip emac nodes don't make use of this common fall back string.
In order to removed unused driver code replace this string with
"rockchip,rk3066-emac".
As we are there remove the blank lines and sort.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 6.10:
- Fix GPIO number for reg_usdhc2_vmmc on imx8qm-mek board.
- Enable hysteresis for SODIMM_17 pin on imx8mm-verdin board to increase
immunity against noise.
- Remove 'no-sdio' property for uSDHC2 on imx93-11x11-evk board, so that
SDIO cards could also work.
- Fix BT shutdown GPIO for imx8mp-venice-gw73xx-2x board.
- Fix panel node deleting on imx53-qsb-hdmi, as /delete-node/ directive
doesn't really delete a node in a DT overlay.
- Fix TC9595 input clock on DH i.MX8M Plus DHCOM SoM.
- Fix GPU speed for imx8mm-verdin board by enabling overdrive mode in
the SOM dtsi.
* tag 'imx-fixes-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: imx8qm-mek: fix gpio number for reg_usdhc2_vmmc
arm64: dts: freescale: imx8mm-verdin: enable hysteresis on slow input pin
arm64: dts: imx93-11x11-evk: Remove the 'no-sdio' property
arm64: dts: freescale: imx8mp-venice-gw73xx-2x: fix BT shutdown GPIO
arm: dts: imx53-qsb-hdmi: Disable panel instead of deleting node
arm64: dts: imx8mp: Fix TC9595 input clock on DH i.MX8M Plus DHCOM SoM
arm64: dts: freescale: imx8mm-verdin: Fix GPU speed
Link: https://lore.kernel.org/r/Zm+xVUmFtaOnYBb4@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi
Pull EFI fixes from Ard Biesheuvel:
"Another small set of EFI fixes. Only the x86 one is likely to affect
any actual users (and has a cc:stable), but the issue it fixes was
only observed in an unusual context (kexec in a confidential VM).
- Ensure that EFI runtime services are not unmapped by PAN on ARM
- Avoid freeing the memory holding the EFI memory map inadvertently
on x86
- Avoid a false positive kmemleak warning on arm64"
* tag 'efi-fixes-for-v6.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
efi/arm64: Fix kmemleak false positive in arm64_efi_rt_init()
efi/x86: Free EFI memory map only when installing a new one.
efi/arm: Disable LPAE PAN when calling EFI runtime services
|
|
'#sound-dai-cells' is required to properly interpret
the list of DAI specified in the 'sound-dai' property,
so add them to the 'hdmi' node for 'rk3066a.dtsi'.
Fixes: fadc78062477 ("ARM: dts: rockchip: add rk3066 hdmi nodes")
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/8b229dcc-94e4-4bbc-9efc-9d5ddd694532@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Since commit fa2d0aa96941
("mmc: core: Allow setting slot index via device tree alias")
mmc numbering are changed, confusing boot scripts. Fix that by adding
proper aliases
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable the LVDS-to-HDMI bridge and the HDMI display connector drivers
used on the iMX53 QSB and QSRB boards with the HDMI mezzanine.
Cc: Chris Healy <cphealy@gmail.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable drivers for devices/features used on MBa7x.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Describe LVDS data mapping of the LVDS-to-DPI decoder input port.
This fixes a warning reported by lvds-codec driver:
"
lvds-codec lvds-decoder: missing 'data-mapping' DT property
"
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
EFI runtime services are remapped into the lower 1 GiB of virtual
address space at boot, so they are guaranteed to be able to co-exist
with the kernel virtual mappings without the need to allocate space for
them in the kernel's vmalloc region, which is rather small.
This means those mappings are covered by TTBR0 when LPAE PAN is enabled,
and so 'user' access must be enabled while such calls are in progress.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
We cannot use /delete-node/ directive to delete a node in a DT
overlay. The node won't be deleted effectively. Instead, set
the node's status property to "disabled" to achieve something
similar.
Fixes: eeb403df953f ("ARM: dts: imx53-qsb: add support for the HDMI expander")
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
