| Age | Commit message (Collapse) | Author |
|---|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Pull "Rockchip dts32 updates for 4.15 part2" from Heiko Stübner:
CEC support for the two rk3288-firefly variants and general hdmi support
for the firefly-reload. A lot of additions and corrections for the
rk3288-vyasa and thermal support for the rv1108.
* tag 'v4.15-rockchip-dts32-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: enable the hdmi output on the rk3288-firefly-reload
ARM: dts: rockchip: define the two possible rk3288 CEC pins
ARM: dts: rockchip: add the cec clk for dw-hdmi on rk3288
ARM: dts: rockchip: Add io domains for rk3288-vyasa
ARM: dts: rockchip: Add usb otg for rk3288-vyasa
ARM: dts: rockchip: Add usb host for rk3288-vyasa
ARM: dts: rockchip: Add gmac support for rk3288-vyasa board
ARM: dts: rockchip: Add regulators for rk3288-vyasa
ARM: dts: rockchip: Use vmmc-supply from PMIC on rk3288-vyasa
ARM: dts: rockchip: Remove vdd_log from rk808, DCDC_REG1 on rk3288-vyasa
ARM: dts: rockchip: enable tsadc module on RV1108 evaluation board
ARM: dts: rockchip: add thermal nodes for RV1108 SoC
ARM: dts: rockchip: add tsadc node for RV1108 SoC
ARM: dts: rockchip: add RGA device node for RK3288
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Pull "Allwinner DT changes for 4.15, take 2" from Maxime Ripard:
Here are a few commits that would be great to get in 4.15, given how
long they've been hanging around.
The first and most important one is the reintroduction of the EMAC DT
changes after they've been reverted at the last minute in 4.13.
There's a arm64 patch that crept in because the H5 and H3 share a
common DTSI that is located in arch/arm, and merging that patch
through the arm64 PR, especially given the pull requests that have
already been sent, would just have generated too many conflicts.
* tag 'sunxi-dt-for-4.15-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: a711: Enable USB OTG
ARM: dts: sun8i: a711: Add regulator support
ARM: dts: sun8i: a83t: bananapi-m3: Enable AP6212 WiFi on mmc1
ARM: dts: sun8i: a83t: cubietruck-plus: Enable AP6330 WiFi on mmc1
ARM: dts: sun8i: a83t: Move mmc1 pinctrl setting to dtsi file
ARM: dts: sun8i: a83t: allwinner-h8homlet-v2: Add AXP818 regulator nodes
ARM: dts: sun8i: a83t: bananapi-m3: Add AXP813 regulator nodes
ARM: dts: sun8i: a83t: cubietruck-plus: Add AXP818 regulator nodes
ARM: dts: sunxi: Add dtsi for AXP81x PMIC
arm64: dts: allwinner: H5: Restore EMAC changes
ARM: dts: sunxi: Restore EMAC changes (boards)
ARM: dts: sunxi: h3/h5: represent the mdio switch used by sun8i-h3-emac
arm: dts: sunxi: h3/h5: Restore EMAC changes
dt-bindings: net: dwmac-sun8i: update documentation about integrated PHY
dt-bindings: net: Restore sun8i dwmac binding
|
|
into next/dt
Pull "Mediatek: 32-bit DTS updates for v4.15" from Matthias Brugger:
- mt7623 update nodes to binding description
- mt2701 add display pwn nodes
- mt2701 update audio node description
* tag 'v4.14-next-dts32-2' of https://github.com/mbgg/linux-mediatek:
arm: dts: mt7623: remove unused compatible string for pio node
arm: dts: mt7623: update usb related nodes
arm: dts: mt7623: update crypto node
arm: dts: mediatek: update audio node for mt2701 and mt7623
arm: dts: mt2701: enable display pwm backlight
arm: dts: mt2701: add pwm backlight device node
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-actions into next/dt
Pull "Actions Semi ARM based SoC DT for v4.15" from Andreas Färber:
This updates the Guitar board DT with a clock node for the debug UART
and adds a new DT for the CubieBoard6.
It also updates the S500 DT with CPU power domains.
* tag 'actions-arm-dt-for-4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-actions:
ARM: dts: owl-s500: Add CubieBoard6
dt-bindings: arm: actions: Add CubieBoard6
ARM: dts: owl-s500-guitar-bb-rev-b: Add fake uart3 clock
ARM: dts: owl-s500: Set power domains for CPU2 and CPU3
|
|
Add a Device Tree for Cubietech CubieBoard6.
Cc: support@cubietech.com
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
Add a fixed-clock for baudrate 115200.
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
CPU2 has its own power domain PD_CPU2, and CPU3 has PD_CPU3.
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
MT7623 has its own compatible in pinctrl driver so we don't need the
backward compatible for it.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
The current usb related nodes are out-of-date, so we make them be
consistent with the binding documents.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
This patch updates compatible string and clocks for the crypto node.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
The TBS A711 has a micro-USB connector that can be used in OTG mode. Enable
it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The TBS A711 is using an AXP813 PMIC. Let's add all the regulators for that
board, and migrate the current, dumb, regulators to the actual ones.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The WiFi side of the AP6212 WiFi/BT combo module is connected to
mmc1. There are also GPIOs for enable and interrupts. An external
clock from the AC100 RTC is also used.
Enable WiFi on this board by enabling mmc1 and adding the power
sequencing clocks and GPIO, as well as the chip's interrupt line.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The WiFi side of the AP6330 WiFi/BT combo module is connected to
mmc1. There are also GPIOs for enable and interrupts. An external
clock from the AC100 RTC is also used.
Enable WiFi on this board by enabling mmc1 and adding the power
sequencing clocks and GPIO, as well as the chip's interrupt line.
For the WiFi module to correctly detect the frequency of its main
oscillator, the external low power clock must be set to 32768 Hz.
Their does not seem to be proper out-of-band interrupt support
for the BCM4330 chip within the AP6330 module. This part is left
out for now.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
mmc1 only has 1 possible pinmux setting.
Move any settings to the dtsi file and set it by default.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
This patch adds device nodes for all the regulators of the AXP818 PMIC.
Sunxi common regulators are removed, and USB VBUS regulators are added.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
This patch adds device nodes for all the regulators of the AXP813 PMIC.
Sunxi common regulators are removed, and USB VBUS regulators are added.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
This patch adds device nodes for all the regulators of the AXP818 PMIC.
Sunxi common regulators are removed, and USB VBUS regulators are added.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The AXP81x family of PMIC is used with the Allwinner A83T and H8 SoCs.
This includes the AXP813 and AXP818. There is no discernible difference
except the labeling. The AXP813 is paired with the A83T, while the
AXP818 is paired with the H8.
This patch adds a dtsi file for all the common bindings for these two
PMICs. Currently this is just listing all the regulator nodes. The
regulators are initialized based on their device node names.
In the future this would be expanded to include power supplies and
GPIO controllers.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The original dwmac-sun8i DT bindings have some issue on how to handle
integrated PHY and was reverted in last RC of 4.13.
But now we have a solution so we need to get back that was reverted.
This patch restore all boards DT about dwmac-sun8i
This reverts partially commit fe45174b72ae ("arm: dts: sunxi: Revert EMAC changes")
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Since dwmac-sun8i could use either an integrated PHY or an external PHY
(which could be at same MDIO address), we need to represent this selection
by a MDIO switch.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The original dwmac-sun8i DT bindings have some issue on how to handle
integrated PHY and was reverted in last RC of 4.13.
But now we have a solution so we need to get back that was reverted.
This patch restore sunxi-h3-h5.dtsi
This reverts partially commit fe45174b72ae ("arm: dts: sunxi: Revert EMAC changes")
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt
Pull "Amlogic 64-bit platforms: DT updates for v4.15" from Kevin Hilman:
- new SoC support: A113D
- new boards: Tronsmart Vega S96, Khadas vim2
- reserved memory fixups
- gpio-names cleanups
- MMC cleanups, enable high-speed modes
- misc cleanups
* tag 'amlogic-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
arm64: dts: meson-axg: add initial A113D SoC DT support
dt-bindings: arm: amlogic: Add Meson AXG binding
ARM64: dts: meson-gx: remove unnecessary uart compatible
ARM64: dts: meson-gx: remove unnecessary clocks properties
ARM64: dts: meson-gxl: Add alternate ARM Trusted Firmware reserved memory zone
ARM64: dts: meson-gxm: enable HS400 on the vim2
ARM64: dts: meson-gxbb-nexbox-a95x: Enable USB Nodes
dt-bindings: arm: amlogic: Add Tronsmart Vega S96 binding
ARM64: dts: meson-gxm: Add Vega S96 board
ARM64: dts: meson-gxm: Add support for Khadas VIM2
ARM64: dts: meson-gxl: Take eMMC data strobe out of eMMC pins
ARM64: dts: meson-gxl: adjust libretech-cc gpio-line-names
ARM64: dts: meson-gxl: adjust kvim gpio-line-names
ARM64: dts: meson-gxbb: adjust odroid-c2 gpio-line-names
ARM64: dts: meson-gxbb: adjust nanopi-k2 gpio-line-names
ARM64: dts: meson-gx: adjust gpio-ranges for TEST_N
ARM64: dts: meson-gx: remove gpio offset
ARM: dts: meson8: remove gpio offset
ARM64: dts: meson-gxl-libretech-cc: enable internal phy leds
ARM64: dts: meson-gxl-libretech-cc: enable saradc
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt
Pull "Amlogic 32-bit DT updates for v4.15, round 2" from Kevin Hilman:
- enable new GPIO IRQ controller
- add efuse node
* tag 'amlogic-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM: dts: meson: add the efuse node
ARM: dts: meson8b: enable gpio interrupt controller
ARM: dts: meson8b: add support for booting the secondary CPU cores
ARM: dts: meson8: add support for booting the secondary CPU cores
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/dt
Pull" ARM: at91: DT for 4.15" from Alexandre Belloni:
- sama5d2 xplained: add charger and SD card power supply
- sama5d27_som1_ek: many adjustments
- at91sam9x25ek: add pwm0 and can1
* tag 'at91-ab-4.15-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: dts: at91: at91sam9x5ek: use DMA for USART0
ARM: dts: at91: at91sam9x25ek: add pwm0
ARM: dts: at91: at91sam9x25ek: add CAN1 interface
ARM: dts: at91: sama5d2_xplained: remove pull-up on SD/MMC lines
ARM: dts: at91: sama5d2_xplained: add pinmuxing for pwm0
ARM: dts: at91: sama5d2_xplained: set PB_USER as wakeup source
ARM: dts: at91: sama5d27_som1_ek: remove pull-up on SD/MMC lines
ARM: dts: at91: sama5d27_som1_ek: remove not connected CAN0
ARM: dts: at91: sama5d27_som1_ek: add pinmuxing for pwm0
ARM: dts: at91: sama5d27_som1_ek: add aliases for i2c
ARM: dts: at91: sama5d27_som1_ek: set USER button as a wakeup source
ARM: dts: at91: sama5d27_som1_ek: update serial aliases
ARM: dts: at91: sama5d27_som1_ek: enable i2c2
ARM: dts: at91: sama5d27_som1_ek: add disabled status
ARM: dts: at91: usb_a9g20: fix rtc node
ARM: dts: at91: sama5d2 Xplained: Describe the SD card power supply
ARM: dts: at91: sama5d2_xplained: Add charger node
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Pull "i.MX device tree updates for 4.15" from Shawn Guo:
- New board support: i.MX51 ZII RDU1, i.MX53 GE Healthcare PPD, i.MX6
TX modules for MB7 from Ka-Ro Electronics, i.MX6 Wandboard revd1
variants, i.MX6 LWN DISPLAY5 board, Pistachio i.MX6Q board, i.MX6SX
Vining-2000 board.
- Use the 'vpcie-supply' property for PCIe device for boards
imx6qdl-sabresd, imx6q-novena and imx6q-cm-fx6.
- A series from Jagan Teki to update imx6qdl-icore board with audio,
touch and CAN support.
- Switch to nvmem for accessing OCOTP from tempmon for i.MX6SX and add
tempmon support for i.MX6UL.
- A bunch of patches from Lothar Waßmann updating Ka-Ro i.MX28, i.MX53
and i.MX6 TX modules.
- Fix DTC warnings in i.MX device trees, dropping leading zeros from
unit address, correcting display nodes notation and display port
names, fixing nodes with unit name and no reg property.
- Other random device updates for various board support.
* tag 'imx-dt-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (63 commits)
ARM: dts: imx53-tx53: fix interrupt flags
ARM: dts: imx28-tx28: fix interrupt flags
ARM: dts: display5: Device tree description of LWN's DISPLAY5 board
ARM: dts: imx53-qsb-common: Fix 'led_gpio7_7@0' node with unit name and no reg property
ARM: dts: imx53-m53evk: Fix 'led_gpio@0' node with unit name and no reg property
ARM: dts: imx53: Fix 'usbphy@x' node with unit name and no reg property
ARM: dts: imx51-ts4800: Fix 'port@0' node with unit name and no reg property
ARM: dts: imx51-apf51dev: Fix 'backlight@bl1' node with unit name and no reg property
ARM: dts: imx: add ZII RDU1 board
ARM: dts: imx: add support for TX6 modules on MB7 baseboard
ARM: dts: imx: add support for TX6QP
ARM: dts: imx6-tx6: add a .dtsi file for the MB7 baseboard
ARM: dts: imx6-tx6: move display configuration to .dtsi file
ARM: dts: imx6-tx6: add support for I2C bus recovery
ARM: dts: imx6-tx6: convert to using simple-audio-card
ARM: dts: imx6-tx6: specify ethernet phy reset post-delay
ARM: dts: imx6-tx6: improve ethernet related pinctrl setup
ARM: dts: imx6-tx6: add trickle-charge config for DS1339
ARM: dts: imx6-tx6: remove obsolete ipu1 alias
ARM: dts: imx6-tx6: remove obsolete eeti,egalax_ts
...
[arnd: made sure we have no new leading zeroes in unit address during merge]
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into next/dt
Pull "UniPhier ARM SoC DT updates for v4.15" from Masahiro Yamada:
- add thermal monitor and thermal zone nodes
- fix W=2 warnings
- add GPIO controller nodes and related properties
- add resets properties
* tag 'uniphier-dt-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
ARM: dts: uniphier: add resets properties
ARM: dts: uniphier: add GPIO hog definition
ARM: dts: uniphier: route on-board device IRQ to GPIO controller
ARM: dts: uniphier: add GPIO controller nodes
ARM: dts: uniphier: fix W=2 build warnings
ARM: dts: uniphier: add nodes of thermal monitor and thermal zone for PXs2
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt
Pull "Amlogic 32-bit platforms: DT updates for v4.15"
- add SDIO MMC controller
- reserved memory fixes
- SoC info driver nodes
- enable USB host controller
* tag 'amlogic-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM: dts: meson: add the SDIO MMC controller
ARM: dts: meson8b: add reserved memory zone to fix silent freezes
ARM: dts: meson: add SoC information nodes
dt-bindings: Amlogic: add documentation for the SoC info register areas
ARM: dts: meson: fixing USB support on Meson6, Meson8 and Meson8b
ARM: dts: meson: enabling the USB Host controller on Odroid-C1/C1+ board
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/dt
Pull "ARM: Keystone DTS update for 4.15" from Santosh Shilimkar:
- McASP support for K2G EVM
- I2C support for K2G EVM
- USB support for K2G EVM
- SPI & SPI NOR flash support for K2G EVM
- ECAP PWM support for K2G EVM
* tag 'keystone_dts_for_4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: dts: keystone-k2g-evm: add bindings for SPI NOR flash
ARM: dts: keystone-k2g: Add SPI nodes
ARM: dts: keystone-k2g-evm: Enable PWM ECAP0
ARM: dts: keystone-k2g: Add ECAP PWM DT nodes
ARM: dts: k2g-evm: Enable USB 0 and 1
ARM: dts: k2g: Add USB instances
ARM: dts: keystone-k2g-evm: Add I2C EEPROM DT entry
ARM: dts: keystone-k2g: Add I2C nodes
ARM: dts: keystone-k2g: Add McASP nodes
|
|
http://github.com/Broadcom/stblinux into next/dt
Pull "Broadcom devicetree changes for 4.15" from Florian Fainelli:
This pull request contains Broadcom ARM-based Device Tree changes for 4.15,
please pull the following:
- Eric adds support for the CLCD and PWM controller on Cygnus chis
- Loic fixes the console path on the Raspberry Pi 3 (already submitted as
fixes) and then proceeds with enabling the BCM43438 bluetooth chip on
the Raspberry Pi 3
- Rafal specifies the USB ports on the Luxul XWR-1200
- Dan adds support for the Luxul ABR-4500 based on BCM47094, the Luxul XAP-810
and XAP-1440 both based on BCM53573
- Florian adds support for the Broadcom Hurricane 2 SoC by adding general
machine binding, clock binding, SoC DTS include file and a DTS for the
Ubiquiti Networks UniFi Switch 8
* tag 'arm-soc/for-4.15/devicetree' of http://github.com/Broadcom/stblinux:
ARM: dts: Hurricane 2: Add basic support for Ubiquiti UniFi Switch 8
dt-bindings: Add Ubiquiti Networks vendor prefix
ARM: dts: Add Broadcom Hurricane 2 DTS include file
dt-bindings: Document Broadcom Hurricane 2 clocks
dt-bindings: Add documentation for Broadcom Hurricane 2 SoCs
ARM: dts: BCM53573: Add DT for Luxul XAP-1440
ARM: dts: BCM53573: Add DT for Luxul XAP-810
ARM: dts: BCM5301X: Add DT for Luxul ABR-4500
ARM: dts: BCM5301X: Add DT for Luxul XBR-4500
ARM: dts: BCM5301X: Specify USB ports for USB LED of Luxul XWR-1200
ARM: dts: bcm2837-rpi-3-b: Add bcm43438 serial slave
ARM: dts: bcm283x: Fix console path on RPi3
ARM: dts: cygnus: Add the PWM node
ARM: dts: cygnus: Add the CLCD controller
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
Pull "ARM: tegra: Device tree changes for v4.15-rc1" from Thierry Reding:
Adds support for the CEC controller found on Tegra124 and enables it on
Tegra K1.
* tag 'tegra-for-4.15-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Enable CEC support on Jetson TK1
ARM: tegra: Add CEC support for Tegra124
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Pull "Second Round of Renesas ARM Based SoC DT Updates for v4.15" from Simon Horman:
* r8a77430 (RZ/G1M) SoC
- Add XHCI support to SoC DT. Boards may enable this as appropriate
* All Renesas ARM based SoCs
- Add missing clocks for ARM CPU cores
Geert Uytterhoeven says "This series improves DT hardware descriptions
for Renesas arm32 SoCs by adding missing clocks properties to the
device nodes corresponding to ARM CPU cores."
* R-Car Gen 1 and 2, and RZ/G SoCs
- Use R-Car Fallback compat strings for GPIO
Simon Horman says "Use newly added R-Car GPIO Gen 1, 2 and 3 fallback
compat strings in peace of now deprecated non-generation specific R-Car
GPIO fallback compat string in the DT of Renesas ARM and arm64 based
SoCs.
As noted in the changelogs for the r8a777[89] changes, this introduces
an incompatibility with pre-v4.14 kernels used with new DTBs. There is
no run-time effect for other SoCs updated by this changeset."
* r7s72100 (RZ/A1H) GR-Peach board
- Add pin configuration subnode for ETHER pin group.
This avoids relying on boot-loader configuration of these pins.
- Enable ostm0 and ostm1 timers
Jacopo Mondi says these are "to be used as clock source and clockevent
source. The timers provides greater accuracy than the already enabled
mtu2 one."
- Correct leds node name indent
- Enable MTU2 timer pulse unit
Jacopo Mondi says "MTU2 multi-function/multi-channel timer/counter is
not enabled for GR-Peach board. The timer is used as clock event source
to schedule wake-ups, and without this enabled all sleeps not performed
through busy waiting hang the board."
* r8a7743 (RZ/G1M) iW-RainboW-G20M-Qseven SoM
- Add USB function support
* r8a7745 (RZ/G1E) iW-RainboW-G22D development platform
- Add USB2.0 Host support
* r8a7743 (RZ/G1M) iW-RainboW-G20D-Qseven development platform
- Rework DT architecture and add DT for camera DB
Fabrizio Castro says "Some of the serial interfaces are exposed on the
camera daughter board. The camera daughter board can be connected to
the carrier board by means of expansion connectors 1, 2 and 3. The
carrier board may host an RZ/G1M or an RZ/G1N based SoM.
While adding support for the serial interfaces on the camera daughter
board we faced the dilemma of how to properly describe all of the
possible HW configurations and how to maximize code reuse.
The best option would be to use device tree overlays, however there is
still some work to be done on that front before actually using them,
therefore for the time being we decided to provide .dtsi files to
describe the carrier board and the camera daughter board, and provide
.dts files to describe the HW configurations we need to support."
* r8a779[0-4] R-Car Gen2 SoCs
- Use generic node name for VSP1 nodes
Geert Uytterhoeven says "This patch series replaces the specific node
names used for the VSP1 nodes by the preferred generic node names, cfr.
commit 0e1bfb72b076b07d ("v4l: vsp1: Use generic node name")."
* tag 'renesas-dt2-for-v4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (42 commits)
ARM: dts: r8a7743: Add xhci support to SoC dtsi
ARM: dts: r7s72100: Add clock for CA9 CPU core
dt-bindings: clk: r7s72100: Add missing I and G clocks
ARM: dts: sh73a0: Add clocks for CA9 CPU cores
ARM: dts: r8a7794: Add missing clock for secondary CA7 CPU core
ARM: dts: r8a7793: Add missing clock for secondary CA15 CPU core
ARM: dts: r8a7792: Add missing clock for secondary CA15 CPU core
ARM: dts: r8a7791: Add missing clock for secondary CA15 CPU core
ARM: dts: r8a7790: Add clocks for CA7 CPU cores
ARM: dts: r8a7790: Add missing clocks for secondary CA15 CPU cores
ARM: dts: r8a7779: Add clocks for CA9 CPU cores
ARM: dts: r8a7778: Add clock for CA9 CPU core
ARM: dts: r8a7743: Add missing clock for secondary CA15 CPU core
ARM: dts: r8a73a4: Add clock for CA15 CPU0 core
ARM: dts: r8a7794: Use R-Car GPIO Gen2 fallback compat string
ARM: dts: r8a7793: Use R-Car GPIO Gen2 fallback compat string
ARM: dts: r8a7792: Use R-Car GPIO Gen2 fallback compat string
ARM: dts: r8a7791: Use R-Car GPIO Gen2 fallback compat string
ARM: dts: r8a7790: Use R-Car GPIO Gen2 fallback compat string
ARM: dts: r8a7743: Use R-Car GPIO Gen2 fallback compat string
...
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Pull "Allwinner DT changes for 4.15" from Maxime Ripard:
The most notable changes are:
- Conversion to the last SoC (A10, A20) to the new clock framework
- HDMI and dual pipeline support for the A10, A20 and A31 DRM driver
- Support for the various power supplies on a number of boards
- Fix of DTC warnings on a number of SoCs, but most of them still need
some work
- New boards: A20-OLinuXino-MICRO-eMMC, TBS A711, Banana Pi M2 Berry,
Banana Pi M2 Ultra
- New R40 SoC support
* tag 'sunxi-dt-for-4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (63 commits)
ARM: sun8i: r40: enable USB host for Banana Pi M2 Ultra
ARM: sun8i: v40: add 5V regulator for Banana Pi M2 Berry
ARM: sun8i: r40: add 5V regulator for Banana Pi M2 Ultra
ARM: sun8i: r40: add USB host port nodes for R40
ARM: dts: sun4i: Enable HDMI support on some A10 devices
ARM: dts: sun7i: Enable HDMI support on some A20 devices
ARM: dts: sun7i: Add device nodes for display pipelines
ARM: dts: sun4i: Add device nodes for display pipelines
ARM: dts: sun8i: r40: add watchdog device node
ARM: dts: sun5i: reference-design-tablet: Enable AXP209 AC and battery
ARM: dts: sun9i: Change node names to remove underscores
ARM: dts: sun9i: Change node names to remove underscores
ARM: dts: sun4i: Remove underscores from nodes names
ARM: dts: sun4i: Provide default muxing for relevant controllers
ARM: dts: sun4i: Change pinctrl nodes to avoid warning
ARM: dts: sun6i: Enable HDMI support on some A31/A31s devices
ARM: dts: sun6i: Add device node for HDMI controller
ARM: dts: sun4i: Change LRADC node names to avoid warnings
ARM: dts: sun4i: Remove skeleton and memory to avoid warnings
ARM: dts: sun4i: Remove gpio-keys warnings
...
|
|
Meson6, Meson8 and Meson8b use a similar IP block which has access to
512 bytes of efuse data.
During SoC manufacturing some calibration settings for the CVBS
connector and the internal temperature sensor are written to this efuse.
On some boards it additionally stores for example the MAC addresses.
The efuse is enabled on Meson8 and Meson8b but kept disabled on Meson6
since we do not have a clock driver there (which is required to read
data from the efuse).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add gpio interrupt controller node to the meson8b boards
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Booting the secondary CPU cores involves the following nodes/devices:
- SCU (Snoop-Control-Unit, for which we already have a DT node)
- a reset line for each CPU core, provided by the reset-controller
which is built into the clock-controller
- the PMU (power management unit) which controls the power of the CPU
cores
- a range in the SRAM specifically reserved for booting secondary CPU
cores
- the "enable-method" which activates booting the secondary CPU cores
This adds all required nodes and properties to boot the secondary CPU
cores.
Signed-off-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Booting the secondary CPU cores involves the following nodes/devices:
- SCU (Snoop-Control-Unit, for which we already have a DT node)
- a reset line for each CPU core, provided by the reset-controller
which is built into the clock-controller
- the PMU (power management unit) which controls the power of the CPU
cores
- a range in the SRAM specifically reserved for booting secondary CPU
cores
- the "enable-method" which activates booting the secondary CPU cores
This adds all required nodes and properties to boot the secondary CPU
cores.
Suggested-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Some interrupts properties are given '0' as the flags argument or no
flags argument at all.
Change them to use the appropriate interrupt flags.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Some interrupts properties are given '0' as the flags argument.
Change them to use the appropriate interrupt flags.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add resets properties to all nodes that have reset lines.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Interrupt lines from on-board devices are connected to the GPIO
controller. Add GPIO hogging so that the corresponding GPIO line
is automatically requested.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Interrupt lines from on-board devices are connected to the GPIO
controller. Handle this correctly.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The GPIO controller also acts as an interrupt controller and the
interrupt lines are connected to the AIDET block.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This commit adds device tree description of Liebherr's Display5 board.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
reg property
The following build warning is seen with W=1:
Warning (unit_address_vs_reg): Node /soc/aips@50000000/iomuxc@53fa8000/imx53-qsb/led_gpio7_7@0 has a unit name, but no reg property
Fix this warning by removing '@0' from such node.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The following build warning is seen with W=1:
Warning (unit_address_vs_reg): Node /soc/aips@50000000/iomuxc@53fa8000/imx53-m53evk/led_gpio@0 has a unit name, but no reg property
Fix this warning by removing '@0' from such node.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The following build warnings are seen with W=1:
Warning (unit_address_vs_reg): Node /soc/aips@50000000/usbphy@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /soc/aips@50000000/usbphy@1 has a unit name, but no reg property
Fix these warnings by changing '@' to '-'.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The following build warning is seen with W=1:
Warning (unit_address_vs_reg): Node /display-di0/port@0 has a unit name,
but no reg property
Fix this warning by removing '@' from such node.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
property
The following build warning is seen with W=1:
Warning (unit_address_vs_reg): Node /backlight@bl1 has a unit name, but no reg property
Fix this warning by removing '@bl1'from such node and change 'bl1grp' to
'backlightgrp', once there is only one backlight in this dts.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This adds support for the Zodiac Inflight Innovations RDU1 board,
which is based on the i.MX51.
It is the predecessor of the already supported ZII RDU2 board and
relies on the bootloader in the same way to enable correct display
and touchscreen nodes.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
