| Age | Commit message (Collapse) | Author |
|---|
|
Now that the common 8250 serial driver supports an "irqflags" field,
we don't need to patch in a custom define into the code.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Different arches use different names, so make sure we define both so
common code (like MTD_XIP) "just works".
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Mainline version of git merged support for Blackfin parts, but we now
need to propagate the gcc arch define to make it work.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
We have to use ioctl numbers that don't collide with common code.
Otherwise, these ones never even get called because the common fs
code swalled all invocations.
Reported-by: Kay Duenzer <kduenzer@maku.eu>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
This board has a SSM2603 codec, so make sure we have the right resources
declared for it.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The RX/TX address is always the same regardless of the size of the access.
That means there is no dedicated "16bit" or "32bit" MMR. Trying to use
these currently leads to compile errors. So change everything to use the
right MMR define.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Ashish Gupta <asg@thelearninglabs.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Since these boards can boot out of NAND, make sure we give u-boot its
own partition by default to avoid clobbering it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
If the kernel's init section is merged back into the main memory region
during boot (which it should since that is how we've laid out the kernel
linker map), we want to make sure that these aren't counted as independent
regions. Otherwise, if a large mapping is attempted which starts in the
init region and extends into the main memory region, the access_ok func
will deny it. This leads to weird messages during runtime like "unable
to map xxx library" from the ldso but upon running the application again,
everything works fine.
So if the address of the end of the init region is the same as the start
of the main memory region, simply enlarge the memory region to include
the init region.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Many Blackfin parts group sets of pins into a single functional unit.
This means you cannot use different pins within a group for different
peripherals. Our resource conflict checking thus far has been limited
to individual pins, so if someone tried to grab a different pin from
the same group, it would be allowed while silently changing the other
pins in the same group.
One common example is the pin set PG12 - PG15 on BF51x parts. They
may either be used with SPI0 (1st function), or they may be used with
PTP/PWM/AMS3 (3rd function). Ideally, we'd like to use PG12 - PG14
for SPI0 while using PG15 with AMS3, but the hardware does not permit
this. In the past, the software would allow the pins to be requested
this way, but ultimately things like the Blackfin SPI driver would
stop working when the hardware rerouted to a different peripheral.
Signed-off-by: steven miao <realmz6@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Reported-by: D Binderman <dcb314@hotmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Flushing caches sometimes requires anomaly workarounds which require
supervisor-only insns. Normally we don't need to flush caches from
userspace so this isn't a problem, but when gcc generates trampolines
on the stack, we do.
So add a new syscall for gcc to use modeled after the mips version.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The BF54x processor has a ton of on-chip peripherals and in order to
support them all, the u-boot image is quite large. So give it 512KiB
in all bootable flashes to make our lives easier.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: steven miao <realmz6@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Make sure we include EMAC_SYSTAT when showing errors.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The predefined i2c address 0x2c doesn't match the configuration of the
ad5280 PINs AD0 and AD1 on the tftlcd add-on board. Both AD0 and AD1
are of voltage 3.3V, which means the i2c address should be 0x2F.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Nothing actually needs to use these MMRs (as direct cache manipulation
is done with the DTEST MMRs), so simply hide the read funcs behind the
anomaly define. They're generally unusable anyways when this anomaly
is in effect.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Rather than use raw numbers for the GPIO pins, use proper GPIO defines.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
When apps run with their stack in L1, some system calls might be made
where a buffer is in the stack as an argument. So make sure the core
Blackfin access code does not reject this memory location.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
This board has an AD1836 codec, so make sure we have the right resources
declared for it.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
If an app is placing its stack in L1 scratchpad SRAM, make sure ptrace
is granted access to it so that gdb can do its thing.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The num_chipselect field for on-chip Blackfin SPI buses is supposed to
be 1 larger than the number of actual CSs available. This is because
the hardware starts counting at 1 and not 0. There is a field for "CS0",
but it is marked as "reserved" everywhere.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
We don't need our own header and structure to hook up the ad5398 part,
so drop the custom resources for it.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Rather than write our own ADP switch driver, use the existing fixed
regulator driver and rewrite the platform resources accordingly.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Some peripherals might generate an error interrupt shortly after the
data interrupt due to the fact that the peripheral isn't serviced fast
enough. In most cases this isn't a problem and is expected behavior.
This hasn't been a problem on most parts since you simply don't request
the error interrupt (or you leave it disabled while there is an expected
state) and do the peripheral status checking in the data interrupt.
The Blackfin SIC allows people to prioritize data and error interrupts,
and the Blackfin CEC allows interrupts of equal or higher priority to
nest. The current default settings gives error interrupts a higher
priority than data interrupts. So if an error occurs while processing
the data interrupt, it will be serviced immediately.
However, the error interrupt on the BF537 SIC cannot be enabled on a
per-peripheral basis. Once the error interrupt is enabled for one
peripheral, it is automatically enabled for all peripherals.
Therefore lower the default multiplexed error interrupt priority so
most people need not worry themselves with this issue.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The NAND platform driver expects the registers to have a "mem"
resource type rather than "io".
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
With the recent kernel update the isp1362-hcd driver evaluates the
IORESOURCE_IRQ resource flags and requests the irq with the given
polarity/edge settings. However the ISP1362 config requires low
level/edge interrupts. Most of the Blackfin boards use some random
flag or no flag at all. Make all boards use a know good flag
IORESOURCE_IRQ_LOWEDGE.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The NAND platform driver expects the registers to have a "mem"
resource type rather than "io".
Signed-off-by: Valentin Yakovenkov <yakovenkov@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Add platform resources for the on-chip CAN peripheral so we can use it.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Make sure we use the right Kconfig names and platform strings.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Now that we've rewritten the GPIO CS handling in the Blackfin SPI
peripheral, we need to update the platform resources accordingly.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Now that the common header defines everything and the SPI drivers are
using it, we can drop these duplicated global namespace polluters.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-2.6-irqflags:
Fix IRQ flag handling naming
MIPS: Add missing #inclusions of <linux/irq.h>
smc91x: Add missing #inclusion of <linux/irq.h>
Drop a couple of unnecessary asm/system.h inclusions
SH: Add missing consts to sys_execve() declaration
Blackfin: Rename IRQ flags handling functions
Blackfin: Add missing dep to asm/irqflags.h
Blackfin: Rename DES PC2() symbol to avoid collision
Blackfin: Split the BF532 BFIN_*_FIO_FLAG() functions to their own header
Blackfin: Split PLL code from mach-specific cdef headers
|
|
While combining things, also switch to the proper SPI bit define names.
This lets us punt the rarely used SPI defines.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The common SPI layers take care of detecting CS conflicts and preventing
two devices from claiming the same CS. This causes problems for the GPIO
CS support we currently have as we are using CS0 to mean "GPIO CS". But
if we have multiple devices using a GPIO CS, the common SPI layers see
multiple devices using the virtual "CS0" and reject any such attempts.
To make both work, we introduce an offset define. This represents the
max number of hardware CS values that the SPI peripheral supports. If
the CS is below this limit, we know we can use the hardware CS. If it's
above, we treat it as a GPIO CS. This keeps the CS unique as seen by
the common code and prevents conflicts.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Expand the BIT_CTL defines to use the naming convention of the hardware,
and expand the masks to cover all documented bits.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
As David points out, the cs_change_per_word option isn't standard, nor is
anyone actually using it. So punt all of the dead code considering it
makes up ~10% of the code size.
Reported-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Fix the IRQ flag handling naming. In linux/irqflags.h under one configuration,
it maps:
local_irq_enable() -> raw_local_irq_enable()
local_irq_disable() -> raw_local_irq_disable()
local_irq_save() -> raw_local_irq_save()
...
and under the other configuration, it maps:
raw_local_irq_enable() -> local_irq_enable()
raw_local_irq_disable() -> local_irq_disable()
raw_local_irq_save() -> local_irq_save()
...
This is quite confusing. There should be one set of names expected of the
arch, and this should be wrapped to give another set of names that are expected
by users of this facility.
Change this to have the arch provide:
flags = arch_local_save_flags()
flags = arch_local_irq_save()
arch_local_irq_restore(flags)
arch_local_irq_disable()
arch_local_irq_enable()
arch_irqs_disabled_flags(flags)
arch_irqs_disabled()
arch_safe_halt()
Then linux/irqflags.h wraps these to provide:
raw_local_save_flags(flags)
raw_local_irq_save(flags)
raw_local_irq_restore(flags)
raw_local_irq_disable()
raw_local_irq_enable()
raw_irqs_disabled_flags(flags)
raw_irqs_disabled()
raw_safe_halt()
with type checking on the flags 'arguments', and then wraps those to provide:
local_save_flags(flags)
local_irq_save(flags)
local_irq_restore(flags)
local_irq_disable()
local_irq_enable()
irqs_disabled_flags(flags)
irqs_disabled()
safe_halt()
with tracing included if enabled.
The arch functions can now all be inline functions rather than some of them
having to be macros.
Signed-off-by: David Howells <dhowells@redhat.com> [X86, FRV, MN10300]
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com> [Tile]
Signed-off-by: Michal Simek <monstr@monstr.eu> [Microblaze]
Tested-by: Catalin Marinas <catalin.marinas@arm.com> [ARM]
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> [AVR]
Acked-by: Tony Luck <tony.luck@intel.com> [IA-64]
Acked-by: Hirokazu Takata <takata@linux-m32r.org> [M32R]
Acked-by: Greg Ungerer <gerg@uclinux.org> [M68K/M68KNOMMU]
Acked-by: Ralf Baechle <ralf@linux-mips.org> [MIPS]
Acked-by: Kyle McMartin <kyle@mcmartin.ca> [PA-RISC]
Acked-by: Paul Mackerras <paulus@samba.org> [PowerPC]
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> [S390]
Acked-by: Chen Liqin <liqin.chen@sunplusct.com> [Score]
Acked-by: Matt Fleming <matt@console-pimps.org> [SH]
Acked-by: David S. Miller <davem@davemloft.net> [Sparc]
Acked-by: Chris Zankel <chris@zankel.net> [Xtensa]
Reviewed-by: Richard Henderson <rth@twiddle.net> [Alpha]
Reviewed-by: Yoshinori Sato <ysato@users.sourceforge.jp> [H8300]
Cc: starvik@axis.com [CRIS]
Cc: jesper.nilsson@axis.com [CRIS]
Cc: linux-cris-kernel@axis.com
|
|
Rename h/w IRQ flags handling functions to be in line with what is expected for
the irq renaming patch. This renames local_*_hw() to hard_local_*() using the
following perl command:
perl -pi -e 's/local_irq_(restore|enable|disable)_hw/hard_local_irq_\1/ or s/local_irq_save_hw([_a-z]*)[(]flags[)]/flags = hard_local_irq_save\1()/' `find arch/blackfin/ -name "*.[ch]"`
and then fixing up asm/irqflags.h manually.
Additionally, arch/hard_local_save_flags() and arch/hard_local_irq_save() both
return the flags rather than passing it through the argument list.
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
Add a missing dependency (mach/blackfin.h) to asm/irqflags.h so that
bfin_read_IMASK() can be used by inline functions.
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
Split the BF532 machine type BFIN_*_FIO_FLAG() functions to their own header
file to avoid circular #include problems as these functions require IRQ flag
handling, which requires asm/blackfin.h, which otherwise requires the header
file that defines these functions.
For good measure, also get rid of the inclusion of asm/blackfin.h from
mach/cdefBF532.h (which is circular) and defBF532.h (which is included by
asm/blackfin.h before including this header).
Signed-off-by: David Howells <dhowells@redhat.com>
|
