| Age | Commit message (Collapse) | Author |
|---|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
These changes based on work by Steven King <sfking@fdwdc.com> to support
the i2c hardware modules on ColdFire SoC family devices.
This is the per SoC hardware support. Contains a common platform device
setup. Each of the SoC family members tends to have some minor local
setup required to initialize the module. But all ColdFire family members
use the same i2c hardware module.
This i2c hardware module is the same as used in the Freescale iMX ARM
based family of SoC devices. Steven's original patches were based on using
a new and different i2c-coldfire.c driver. But this is not neccessary as
we can use the existing Linux i2c-imx.c driver with no change required to
it. And this patch is now based on using the existing i2c-imx driver.
This patch only contains the ColdFire platform changes.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Tested-by: Angelo Dureghello <angelo@sysam.it>
|
|
The inclusion of multiple FEC ethernet platform devices is based around
the FEC address definitions in the platform headers. The ColdFire m527x
platform is defining 2 FEC modules, but the 5271 SoC only has a single
FEC hardware module. The attempt to probe and init a second FEC module
causes a trap and dump on boot on this platform.
Fix the definitions so that only the 5275 SoC platform (which has 2 FEC
hardware modules) defines the second base address.
Reported-by: ertheb <3rth3bnospam@ethe.fr>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Fix tab broken address defines to be consistent with others in this file.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Remove the last address definitions relative to the IPSBAR peripheral region
for the ColdFire 527x family. This involved cleaning up some magic numbers
used in the code part, and making them proper register definitions in the 527x
specific header.
This is part of the process of cleaning up the ColdFire register definitions
to make them consistently use absolute addresses for the primary registers.
This will reduce the occasional bugs caused by inconsistent definition of
the register addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
use MCF_IRQ_PIT1 instead of MCFINT_VECBASE + MCFINT_PIT1 so we can support
those parts that have the pit1 interrupt on other than the first interrupt
controller.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
If we make all MCF_RCR (CPU reset register) addressing consistent across all
ColdFire CPU family members that use it then we will be able to remove the
duplicated copies of the code that use it.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
If we make all QSPI (SPI protocol) addressing consistent across all ColdFire
family members then we will be able to remove the duplicated plaform data
and code and use a single setup for all.
So modify the ColdFire 527x QSPI addressing so that:
. base addresses are absolute (not relative to MBAR peripheral register)
. use a common name for IRQs used
. move chip select definitions (CS) to appropriate header
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
If we make all FEC (ethernet) addressing consistent across all ColdFire
family members then we will be able to remove the duplicated plaform data
and use a single setup for all.
So modify the ColdFire 527x FEC addressing so that:
. FECs are numbered from 0 up
. base addresses are absolute (not relative to MBAR peripheral register)
. use a common name for IRQs used
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
If we make all UART addressing consistent across all ColdFire family members
then we will be able to remove the duplicated plaform data and use a single
setup for all.
So modify the ColdFire 527x UART addressing so that:
. UARTs are numbered from 0 up
. use a common name for IRQs used
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
|
|
The EDGE Port module of some ColdFire parts using the intc-2 interrupt
controller provides support for 7 external interrupts. These interrupts
go off-chip (that is they are not for internal peripherals). They need
some special handling and have some extra setup registers. Add code to
support them.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The reality is that you do not need the abiltity to configure the
clock divider for ColdFire CPUs. It is a fixed ratio on any given
ColdFire family member. It is not the same for all ColdFire parts,
but it is always the same in a model range. So hard define the divider
for each supported ColdFire CPU type and remove the Kconfig option.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
In some of the RAM size autodetection code on ColdFire CPU startup
we reference DRAM registers relative to the MBAR register. Not all of
the supported ColdFire CPUs have an MBAR, and currently this works
because we fake an MBAR address on those registers. In an effort to
clean this up, and eventually remove the fake MBAR setting make the
DRAM register address definitions actually contain the MBAR (or IPSBAR
as appropriate) value as required.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The base addresses of the ColdFire DMA unit registers belong with
all the other address definitions in the per-cpu headers. The current
definitions assume they are relative to an MBAR register. Not all
ColdFire CPUs have an MBAR register. A clean address define can only
be acheived in the per-cpu headers along with all the other chips
peripheral base addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The ColdFire 527x family of CPUs does not have an MBAR register, so don't
define its peripheral addresses relative to one. Its internal peripherals
are relative to the IPSBAR register, so make sure to use that.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The PIT hardware timer module used in some ColdFire CPU's is not always
addressed relative to an IPSBAR register. Parts like the ColdFire 5207 and
5208 have fixed peripheral addresses. So lets not define the register
addresses of the PIT relative to an IPSBAR definition. Move the base
address definitions into the per-part headers. This is a lot more consistent
since all the other peripheral base addresses are defined in the per-part
header files already.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The ColdFire 54xx family shares the same interrupt controller used
on the 523x, 527x and 528x ColdFire parts, but it isn't offset
relative to the IPSBAR register. The 54xx doesn't have an IPSBAR
register.
By including the base address of the peripheral registers in the register
definitions (MCFICM_INTC0 and MCFICM_INTC1 in this case) we can avoid
having to define a fake IPSBAR for the 54xx. And this makes the register
address definitions of these more consistent, the majority of the other
register address defines include the peripheral base address already.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The version 2 ColdFire CPU based cores all contain a similar cache
controller unit. Create a set of bit flag definitions for the supporting
registers.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The ColdFire UART base addresses varies between the different ColdFire
family members. Instead of keeping the base addresses with the UART
definitions keep them with the other addresses definitions for each
ColdFire part.
The motivation for this move is so that when we add new ColdFire
part definitions, they are all in a single file (and we shouldn't
normally need to modify the UART definitions in mcfuart.h at all).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The instruction timings of the ColdFire 54xx family parts are
different to other version 4 parts (or version 2 or 3 parts for
that matter too).
Move the instruction timing setting into the ColdFire part
specific headers, and set the 54xx value appropriately.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Move the ColdFire CPU names out of setup.c and into their repsective
headers. That way when we add new ones we won't need to modify
setup.c any more.
Add the missing 548x CPU name.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Since Grant has added the coldfire-qspi driver to next-spi, here is the
platform support for the parts that have qspi hardware. This sets up
gpio to do the spi chip select using the default chip select pins; it should
be trivial for boards that require different or additional spi chip selects to
use other gpios as needed.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Add support for the 5271 & 5275.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Merge header files for m68k and m68knommu to the single location:
arch/m68k/include/asm
The majority of this patch was the result of the
script that is included in the changelog below.
The script was originally written by Arnd Bergman and
exten by me to cover a few more files.
When the header files differed the script uses the following:
The original m68k file is named <file>_mm.h [mm for memory manager]
The m68knommu file is named <file>_no.h [no for no memory manager]
The files uses the following include guard:
This include gaurd works as the m68knommu toolchain set
the __uClinux__ symbol - so this should work in userspace too.
Merging the header files for m68k and m68knommu exposes the
(unexpected?) ABI differences thus it is easier to actually
identify these and thus to fix them.
The commit has been build tested with both a m68k and
a m68knommu toolchain - with success.
The commit has also been tested with "make headers_check"
and this patch fixes make headers_check for m68knommu.
The script used:
TARGET=arch/m68k/include/asm
SOURCE=arch/m68knommu/include/asm
INCLUDE="cachectl.h errno.h fcntl.h hwtest.h ioctls.h ipcbuf.h \
linkage.h math-emu.h md.h mman.h movs.h msgbuf.h openprom.h \
oplib.h poll.h posix_types.h resource.h rtc.h sembuf.h shmbuf.h \
shm.h shmparam.h socket.h sockios.h spinlock.h statfs.h stat.h \
termbits.h termios.h tlb.h types.h user.h"
EQUAL="auxvec.h cputime.h device.h emergency-restart.h futex.h \
ioctl.h irq_regs.h kdebug.h local.h mutex.h percpu.h \
sections.h topology.h"
NOMUUFILES="anchor.h bootstd.h coldfire.h commproc.h dbg.h \
elia.h flat.h m5206sim.h m520xsim.h m523xsim.h m5249sim.h \
m5272sim.h m527xsim.h m528xsim.h m5307sim.h m532xsim.h \
m5407sim.h m68360_enet.h m68360.h m68360_pram.h m68360_quicc.h \
m68360_regs.h MC68328.h MC68332.h MC68EZ328.h MC68VZ328.h \
mcfcache.h mcfdma.h mcfmbus.h mcfne.h mcfpci.h mcfpit.h \
mcfsim.h mcfsmc.h mcftimer.h mcfuart.h mcfwdebug.h \
nettel.h quicc_simple.h smp.h"
FILES="atomic.h bitops.h bootinfo.h bug.h bugs.h byteorder.h cache.h \
cacheflush.h checksum.h current.h delay.h div64.h \
dma-mapping.h dma.h elf.h entry.h fb.h fpu.h hardirq.h hw_irq.h io.h \
irq.h kmap_types.h machdep.h mc146818rtc.h mmu.h mmu_context.h \
module.h page.h page_offset.h param.h pci.h pgalloc.h \
pgtable.h processor.h ptrace.h scatterlist.h segment.h \
setup.h sigcontext.h siginfo.h signal.h string.h system.h swab.h \
thread_info.h timex.h tlbflush.h traps.h uaccess.h ucontext.h \
unaligned.h unistd.h"
mergefile() {
BASE=${1%.h}
git mv ${SOURCE}/$1 ${TARGET}/${BASE}_no.h
git mv ${TARGET}/$1 ${TARGET}/${BASE}_mm.h
cat << EOF > ${TARGET}/$1
EOF
git add ${TARGET}/$1
}
set -e
mkdir -p ${TARGET}
git mv include/asm-m68k/* ${TARGET}
rmdir include/asm-m68k
git rm ${SOURCE}/Kbuild
for F in $INCLUDE $EQUAL; do
git rm ${SOURCE}/$F
done
for F in $NOMUUFILES; do
git mv ${SOURCE}/$F ${TARGET}/$F
done
for F in $FILES ; do
mergefile $F
done
rmdir arch/m68knommu/include/asm
rmdir arch/m68knommu/include
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
