| Age | Commit message (Collapse) | Author |
|---|
|
Export pcibios_free_controller(), so it can be used by the cxl module to
free virtual PHBs.
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Revert dff22d2054b5 ("PCI: Call pci_read_bridge_bases() from core instead
of arch code").
Reading PCI bridge windows is not arch-specific in itself, but there is PCI
core code that doesn't work correctly if we read them too early. For
example, Hannes found this case on an ARM Freescale i.mx6 board:
pci_bus 0000:00: root bus resource [mem 0x01000000-0x01efffff]
pci 0000:00:00.0: PCI bridge to [bus 01-ff]
pci 0000:00:00.0: BAR 8: no space for [mem size 0x01000000] (mem window)
pci 0000:01:00.0: BAR 2: failed to assign [mem size 0x00200000]
pci 0000:01:00.0: BAR 1: failed to assign [mem size 0x00004000]
pci 0000:01:00.0: BAR 0: failed to assign [mem size 0x00000100]
The 00:00.0 mem window needs to be at least 3MB: the 01:00.0 device needs
0x204100 of space, and mem windows are megabyte-aligned.
Bus sizing can increase a bridge window size, but never *decrease* it (see
d65245c3297a ("PCI: don't shrink bridge resources")). Prior to
dff22d2054b5, ARM didn't read bridge windows at all, so the "original size"
was zero, and we assigned a 3MB window.
After dff22d2054b5, we read the bridge windows before sizing the bus. The
firmware programmed a 16MB window (size 0x01000000) in 00:00.0, and since
we never decrease the size, we kept 16MB even though we only needed 3MB.
But 16MB doesn't fit in the host bridge aperture, so we failed to assign
space for the window and the downstream devices.
I think this is a defect in the PCI core: we shouldn't rely on the firmware
to assign sensible windows.
Ray reported a similar problem, also on ARM, with Broadcom iProc.
Issues like this are too hard to fix right now, so revert dff22d2054b5.
Reported-by: Hannes <oe5hpm@gmail.com>
Reported-by: Ray Jui <rjui@broadcom.com>
Link: http://lkml.kernel.org/r/CAAa04yFQEUJm7Jj1qMT57-LG7ZGtnhNDBe=PpSRa70Mj+XhW-A@mail.gmail.com
Link: http://lkml.kernel.org/r/55F75BB8.4070405@broadcom.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- support "hybrid" iommu/direct DMA ops for coherent_mask < dma_mask
from Benjamin Herrenschmidt
- EEH fixes for SRIOV from Gavin
- introduce rtas_get_sensor_fast() for IRQ handlers from Thomas Huth
- use hardware RNG for arch_get_random_seed_* not arch_get_random_*
from Paul Mackerras
- seccomp filter support from Michael Ellerman
- opal_cec_reboot2() handling for HMIs & machine checks from Mahesh
Salgaonkar
- add powerpc timebase as a trace clock source from Naveen N. Rao
- misc cleanups in the xmon, signal & SLB code from Anshuman Khandual
- add an inline function to update POWER8 HID0 from Gautham R. Shenoy
- fix pte_pagesize_index() crash on 4K w/64K hash from Michael Ellerman
- drop support for 64K local store on 4K kernels from Michael Ellerman
- move dma_get_required_mask() from pnv_phb to pci_controller_ops from
Andrew Donnellan
- initialize distance lookup table from drconf path from Nikunj A
Dadhania
- enable RTC class support from Vaibhav Jain
- disable automatically blocked PCI config from Gavin Shan
- add LEDs driver for PowerNV platform from Vasant Hegde
- fix endianness issues in the HVSI driver from Laurent Dufour
- kexec endian fixes from Samuel Mendoza-Jonas
- fix corrupted pdn list from Gavin Shan
- fix fenced PHB caused by eeh_slot_error_detail() from Gavin Shan
- Freescale updates from Scott: Highlights include 32-bit memcpy/memset
optimizations, checksum optimizations, 85xx config fragments and
updates, device tree updates, e6500 fixes for non-SMP, and misc
cleanup and minor fixes.
- a ton of cxl updates & fixes:
- add explicit precision specifiers from Rasmus Villemoes
- use more common format specifier from Rasmus Villemoes
- destroy cxl_adapter_idr on module_exit from Johannes Thumshirn
- destroy afu->contexts_idr on release of an afu from Johannes
Thumshirn
- compile with -Werror from Daniel Axtens
- EEH support from Daniel Axtens
- plug irq_bitmap getting leaked in cxl_context from Vaibhav Jain
- add alternate MMIO error handling from Ian Munsie
- allow release of contexts which have been OPENED but not STARTED
from Andrew Donnellan
- remove use of macro DEFINE_PCI_DEVICE_TABLE from Vaishali Thakkar
- release irqs if memory allocation fails from Vaibhav Jain
- remove racy attempt to force EEH invocation in reset from Daniel
Axtens
- fix + cleanup error paths in cxl_dev_context_init from Ian Munsie
- fix force unmapping mmaps of contexts allocated through the kernel
api from Ian Munsie
- set up and enable PSL Timebase from Philippe Bergheaud
* tag 'powerpc-4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (140 commits)
cxl: Set up and enable PSL Timebase
cxl: Fix force unmapping mmaps of contexts allocated through the kernel api
cxl: Fix + cleanup error paths in cxl_dev_context_init
powerpc/eeh: Fix fenced PHB caused by eeh_slot_error_detail()
powerpc/pseries: Cleanup on pci_dn_reconfig_notifier()
powerpc/pseries: Fix corrupted pdn list
powerpc/powernv: Enable LEDS support
powerpc/iommu: Set default DMA offset in dma_dev_setup
cxl: Remove racy attempt to force EEH invocation in reset
cxl: Release irqs if memory allocation fails
cxl: Remove use of macro DEFINE_PCI_DEVICE_TABLE
powerpc/powernv: Fix mis-merge of OPAL support for LEDS driver
powerpc/powernv: Reset HILE before kexec_sequence()
powerpc/kexec: Reset secondary cpu endianness before kexec
powerpc/hvsi: Fix endianness issues in the HVSI driver
leds/powernv: Add driver for PowerNV platform
powerpc/powernv: Create LED platform device
powerpc/powernv: Add OPAL interfaces for accessing and modifying system LED states
powerpc/powernv: Fix the log message when disabling VF
cxl: Allow release of contexts which have been OPENED but not STARTED
...
|
|
Use %pR to simplify the debug code. This also make the debug info more
readable.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
[mpe: Unsplit multi-line printk strings]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
When we scan a PCI bus, we read PCI-PCI bridge window registers with
pci_read_bridge_bases() so we can validate the resource hierarchy. Most
architectures call pci_read_bridge_bases() from pcibios_fixup_bus(), but
PCI-PCI bridges are not arch-specific, so this doesn't need to be in
arch-specific code.
Call pci_read_bridge_bases() directly from the PCI core instead of from
arch code.
For alpha and mips, we now call pci_read_bridge_bases() always; previously
we only called it if PCI_PROBE_ONLY was set.
[bhelgaas: changelog]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Ralf Baechle <ralf@linux-mips.org>
CC: James E.J. Bottomley <jejb@parisc-linux.org>
CC: Michael Ellerman <mpe@ellerman.id.au>
CC: Bjorn Helgaas <bhelgaas@google.com>
CC: Richard Henderson <rth@twiddle.net>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: David Howells <dhowells@redhat.com>
CC: Russell King <linux@arm.linux.org.uk>
CC: Tony Luck <tony.luck@intel.com>
CC: David S. Miller <davem@davemloft.net>
CC: Ingo Molnar <mingo@redhat.com>
CC: Guenter Roeck <linux@roeck-us.net>
CC: Michal Simek <monstr@monstr.eu>
CC: Chris Zankel <chris@zankel.net>
|
|
This adds a hook into the powerpc pci code for pci_disable_device() calls. The
generic code already provides a weak pcibios_disable_device() symbol, so we
just need to provide our own in powerpc and it'll get picked up.
This is passed directly to the phb controller ops, provided one exists.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Export pcibios_claim_one_bus, pcibios_scan_phb and pcibios_alloc_controller.
These will be used by the CXL driver.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc into next
Merge Richard's work to support SR-IOV on PowerNV. All generic PCI
patches acked by Bjorn.
Some minor conflicts with Daniel's pci_controller_ops work.
Conflicts:
arch/powerpc/include/asm/machdep.h
arch/powerpc/platforms/powernv/pci-ioda.c
|
|
Remove shims, patch callsites to use pci_controller_ops
versions instead.
Also move back the probe mode defines, as explained in the patch
for pci_probe_mode.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Add pci_controller_ops.reset_secondary_bus,
shadowing ppc_md.pcibios_reset_secondary_bus.
Add a shim, and changes the callsites to use the shim.
Use pcibios_reset_secondary_bus_shim, as both
pcibios_reset_secondary_bus and pci_reset_secondary_bus
are already taken.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Add pci_controller_ops.window_alignment,
shadowing ppc_md.pcibios_window_alignment.
Add a shim, and changes the callsites to use the shim.
Here, we use pci_window_alignment, as pcibios_window_alignment is
already taken.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Add pci_controller_ops.enable_device_hook,
shadowing ppc_md.pcibios_enable_device_hook.
Add a shim, and changes the callsites to use the shim.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Add pci_controller_ops.probe_mode, shadowing ppc_md.pci_probe_mode.
Add a shim, and changes the callsites to use the shim.
We also need to move the probe mode defines to pci-bridge.h from pci.h.
They are required by the shim in order to return a sensible default.
Previously, the were defined in pci.h, but pci.h includes pci-bridge.h
before the relevant #defines. This means the definitions are absent
if pci.h is included before pci-bridge.h. This occurs in some drivers.
So, move the definitons now, and move them back when we remove the shim.
Anything that wants the defines would have had to include pci.h, and
since pci.h includes pci-bridge.h, nothing will lose access to the
defines.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Add pci_controller_ops.dma_bus_setup, shadowing ppc_md.pci_dma_bus_setup.
Add a shim, and changes the callsites to use the shim.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Introduces the pci_controller_ops structure.
Add pci_controller_ops.dma_dev_setup, shadowing ppc_md.pci_dma_dev_setup.
Add a shim, and change the callsites to use the shim.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
pcibios_enable_device_hook returned an int. Every implementation
returned either -EINVAL or 0. The return value wasn't propagated by
the caller: any non-zero return value caused pcibios_enable_device
to return -EINVAL itself. Therefore, make the hook return a bool.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
We have a powerpc specific global called mem_init_done which is "set on
boot once kmalloc can be called".
But that's not *quite* true. We set it at the bottom of mem_init(), and
rely on the fact that mm_init() calls kmem_cache_init() immediately
after that, and nothing is running in parallel.
So replace it with the generic and 100% correct slab_is_available().
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Implement pcibios_iov_resource_alignment() on powernv platform.
On PowerNV platform, there are 3 cases for the IOV BAR:
1. initial state, the IOV BAR size is multiple times of VF BAR size
2. after expanded, the IOV BAR size is expanded to meet the M64 segment size
3. sizing stage, the IOV BAR is truncated to 0
pnv_pci_iov_resource_alignment() handle these three cases respectively.
[bhelgaas: adjust to drop "align" parameter, return pci_iov_resource_size()
if no ppc_md machdep_call version]
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
number of total_pe
On PHB3, PF IOV BAR will be covered by M64 BAR to have better PE isolation.
M64 BAR is a type of hardware resource in PHB3, which could map a range of
MMIO to PE numbers on powernv platform. And this range is divided equally
by the number of total_pe with each divided range mapping to a PE number.
Also, the M64 BAR must map a MMIO range with power-of-two size.
The total_pe number is usually different from total_VFs, which can lead to
a conflict between MMIO space and the PE number.
For example, if total_VFs is 128 and total_pe is 256, the second half of
M64 BAR will be part of other PCI device, which may already belong to other
PEs.
This patch prevents the conflict by reserving additional space for the PF
IOV BAR, which is total_pe number of VF's BAR size.
[bhelgaas: make dev_printk() output more consistent, index resource[]
conventionally]
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Flag PCI_REASSIGN_ALL_RSRC is used to ignore resources information setup by
firmware, so that kernel would re-assign all resources of pci devices.
On powerpc arch, this happens in a header fixup function
pcibios_fixup_resources(), which will clean up the resources if this flag
is set. This works fine for PFs, since after clean up, kernel will
re-assign the resources in pcibios_resource_survey().
Below is a simple call flow on how it works:
pcibios_init
pcibios_scan_phb
pci_scan_child_bus
...
pci_device_add
pci_fixup_device(pci_fixup_header)
pcibios_fixup_resources # header fixup
for (i = 0; i < DEVICE_COUNT_RESOURCE; i++)
dev->resource[i].start = 0
pcibios_resource_survey # re-assign
pcibios_allocate_resources
However, the VF resources won't be re-assigned, since the VF resources are
completely determined by the PF resources, and the PF resources have
already been reassigned. This means we need to leave VF's resources
un-cleared in pcibios_fixup_resources().
In this patch, we skip the resource unset process in
pcibios_fixup_resources(), if the pci_dev is a VF.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Every PCI-PCI bridge window should fit inside an upstream bridge window
because orphaned address space is unreachable from the primary side of the
upstream bridge. If we inherit invalid bridge windows that overlap an
upstream window from firmware, clip them to fit and update the bridge
accordingly.
[bhelgaas: changelog]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=85491
Reported-by: Marek Kordik <kordikmarek@gmail.com>
Fixes: 5b28541552ef ("PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Paul Mackerras <paulus@samba.org>
CC: Michael Ellerman <mpe@ellerman.id.au>
CC: Gavin Shan <gwshan@linux.vnet.ibm.com>
CC: Anton Blanchard <anton@samba.org>
CC: Sebastian Ott <sebott@linux.vnet.ibm.com>
CC: Wei Yang <weiyang@linux.vnet.ibm.com>
CC: Andrew Murray <amurray@embedded-bits.co.uk>
CC: linuxppc-dev@lists.ozlabs.org
|
|
Although we are now selecting NO_BOOTMEM, we still have some traces of
bootmem lying around. That is because even with NO_BOOTMEM there is
still a shim that converts bootmem calls into memblock calls, but
ultimately we want to remove all traces of bootmem.
Most of the patch is conversions from alloc_bootmem() to
memblock_virt_alloc(). In general a call such as:
p = (struct foo *)alloc_bootmem(x);
Becomes:
p = memblock_virt_alloc(x, 0);
We don't need the cast because memblock_virt_alloc() returns a void *.
The alignment value of zero tells memblock to use the default alignment,
which is SMP_CACHE_BYTES, the same value alloc_bootmem() uses.
We remove a number of NULL checks on the result of
memblock_virt_alloc(). That is because memblock_virt_alloc() will panic
if it can't allocate, in exactly the same way as alloc_bootmem(), so the
NULL checks are and always have been redundant.
The memory returned by memblock_virt_alloc() is already zeroed, so we
remove several memsets of the result of memblock_virt_alloc().
Finally we convert a few uses of __alloc_bootmem(x, y, MAX_DMA_ADDRESS)
to just plain memblock_virt_alloc(). We don't use memblock_alloc_base()
because MAX_DMA_ADDRESS is ~0ul on powerpc, so limiting the allocation
to that is pointless, 16XB ought to be enough for anyone.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Newer POWER designs do not implement PCI I/O space, so we
expect to see a number of these.
Reduce the severity of the warning so it doesn't mask other
real issues.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Commit 0b0b0893d49b "of/pci: Fix the conversion of IO ranges into IO
resources" changed the behaviour of of_pci_range_to_resource().
Previously it simply populated the resource based on the arguments. Now
it calls pci_register_io_range() and pci_address_to_pio(). These both
have two implementations depending on whether PCI_IOBASE is defined,
which it is not for powerpc.
Further complicating matters, both routines are weak, and powerpc
implements it's own version of one - pci_address_to_pio(). However
powerpc's implementation depends on other initialisations which are done
later in boot.
The end result is incorrectly initialised IO space. Often we can get
away with that, because we don't make much use of IO space. However
virtio requires it, so we see eg:
pci_bus 0000:00: root bus resource [io 0xffff] (bus address [0xffffffffffffffff-0xffffffffffffffff])
PCI: Cannot allocate resource region 0 of device 0000:00:01.0, will remap
virtio-pci 0000:00:01.0: can't enable device: BAR 0 [io size 0x0020] not assigned
The simplest fix for now is to just stop using of_pci_range_to_resource(),
and open-code the original implementation, that's all we want it to do.
Fixes: 0b0b0893d49b ("of/pci: Fix the conversion of IO ranges into IO resources")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
pci_bus_find_capability() is decleared in pci.h, so it is not necessary to do
it again.
This patch removes it.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Since the logic to reset PCI secondary bus by PCI config register
PCI_BRIDGE_CTL_BUS_RESET is included in pci_reset_secondary_bus(), we
needn't implement another one.
Remove the duplicate implementation and call pci_reset_secondary_bus().
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc updates from Ben Herrenschmidt:
"Here is the bulk of the powerpc changes for this merge window. It got
a bit delayed in part because I wasn't paying attention, and in part
because I discovered I had a core PCI change without a PCI maintainer
ack in it. Bjorn eventually agreed it was ok to merge it though we'll
probably improve it later and I didn't want to rebase to add his ack.
There is going to be a bit more next week, essentially fixes that I
still want to sort through and test.
The biggest item this time is the support to build the ppc64 LE kernel
with our new v2 ABI. We previously supported v2 userspace but the
kernel itself was a tougher nut to crack. This is now sorted mostly
thanks to Anton and Rusty.
We also have a fairly big series from Cedric that add support for
64-bit LE zImage boot wrapper. This was made harder by the fact that
traditionally our zImage wrapper was always 32-bit, but our new LE
toolchains don't really support 32-bit anymore (it's somewhat there
but not really "supported") so we didn't want to rely on it. This
meant more churn that just endian fixes.
This brings some more LE bits as well, such as the ability to run in
LE mode without a hypervisor (ie. under OPAL firmware) by doing the
right OPAL call to reinitialize the CPU to take HV interrupts in the
right mode and the usual pile of endian fixes.
There's another series from Gavin adding EEH improvements (one day we
*will* have a release with less than 20 EEH patches, I promise!).
Another highlight is the support for the "Split core" functionality on
P8 by Michael. This allows a P8 core to be split into "sub cores" of
4 threads which allows the subcores to run different guests under KVM
(the HW still doesn't support a partition per thread).
And then the usual misc bits and fixes ..."
[ Further delayed by gmail deciding that BenH is a dirty spammer.
Google knows. ]
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (155 commits)
powerpc/powernv: Add missing include to LPC code
selftests/powerpc: Test the THP bug we fixed in the previous commit
powerpc/mm: Check paca psize is up to date for huge mappings
powerpc/powernv: Pass buffer size to OPAL validate flash call
powerpc/pseries: hcall functions are exported to modules, need _GLOBAL_TOC()
powerpc: Exported functions __clear_user and copy_page use r2 so need _GLOBAL_TOC()
powerpc/powernv: Set memory_block_size_bytes to 256MB
powerpc: Allow ppc_md platform hook to override memory_block_size_bytes
powerpc/powernv: Fix endian issues in memory error handling code
powerpc/eeh: Skip eeh sysfs when eeh is disabled
powerpc: 64bit sendfile is capped at 2GB
powerpc/powernv: Provide debugfs access to the LPC bus via OPAL
powerpc/serial: Use saner flags when creating legacy ports
powerpc: Add cpu family documentation
powerpc/xmon: Fix up xmon format strings
powerpc/powernv: Add calls to support little endian host
powerpc: Document sysfs DSCR interface
powerpc: Fix regression of per-CPU DSCR setting
powerpc: Split __SYSFS_SPRSETUP macro
arch: powerpc/fadump: Cleaning up inconsistent NULL checks
...
|
|
Move the devspec OF attribute to PCI common code's set of device attributes
since it's not architecture dependent. As a side effect microblaze and
powerpc no longer need to use pcibios_add_platform_entries().
[bhelgaas: fold in #include for compile error]
Link: https://lkml.kernel.org/r/alpine.LFD.2.11.1404141101500.1529@denkbrett
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This patch updates the implementation of pci_process_bridge_OF_ranges to use
the of_pci_range_parser helpers.
Signed-off-by: Andrew Murray <amurray@embedded-bits.co.uk>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The problem was initially reported by Wendy who tried pass through
IPR adapter, which was connected to PHB root port directly, to KVM
based guest. When doing that, pci_reset_bridge_secondary_bus() was
called by VFIO driver and linkDown was detected by the root port.
That caused all PEs to be frozen.
The patch fixes the issue by routing the reset for the secondary bus
of root port to underly firmware. For that, one more weak function
pci_reset_secondary_bus() is introduced so that the individual platforms
can override that and do specific reset for bridge's secondary bus.
Reported-by: Wendy Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
These interfaces:
pcibios_resource_to_bus(struct pci_dev *dev, *bus_region, *resource)
pcibios_bus_to_resource(struct pci_dev *dev, *resource, *bus_region)
took a pci_dev, but they really depend only on the pci_bus. And we want to
use them in resource allocation paths where we have the bus but not a
device, so this patch converts them to take the pci_bus instead of the
pci_dev:
pcibios_resource_to_bus(struct pci_bus *bus, *bus_region, *resource)
pcibios_bus_to_resource(struct pci_bus *bus, *resource, *bus_region)
In fact, with standard PCI-PCI bridges, they only depend on the host
bridge, because that's the only place address translation occurs, but
we aren't going that far yet.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
All the callers of irq_create_of_mapping() pass the contents of a struct
of_phandle_args structure to the function. Since all the callers already
have an of_phandle_args pointer, why not pass it directly to
irq_create_of_mapping()?
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Michal Simek <monstr@monstr.eu>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
struct of_irq and struct of_phandle_args are exactly the same structure.
This patch makes the kernel use of_phandle_args everywhere. This in
itself isn't a big deal, but it makes some follow-on patches simpler.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Michal Simek <monstr@monstr.eu>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The OF irq handling code has been overloading the term 'map' to refer to
both parsing the data in the device tree and mapping it to the internal
linux irq system. This is probably because the device tree does have the
concept of an 'interrupt-map' function for translating interrupt
references from one node to another, but 'map' is still confusing when
the primary purpose of some of the functions are to parse the DT data.
This patch renames all the of_irq_map_* functions to of_irq_parse_*
which makes it clear that there is a difference between the parsing
phase and the mapping phase. Kernel code can make use of just the
parsing or just the mapping support as needed by the subsystem.
The patch was generated mechanically with a handful of sed commands.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Michal Simek <monstr@monstr.eu>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc updates from Ben Herrenschmidt:
"Here's the powerpc batch for this merge window. Some of the
highlights are:
- A bunch of endian fixes ! We don't have full LE support yet in that
release but this contains a lot of fixes all over arch/powerpc to
use the proper accessors, call the firmware with the right endian
mode, etc...
- A few updates to our "powernv" platform (non-virtualized, the one
to run KVM on), among other, support for bridging the P8 LPC bus
for UARTs, support and some EEH fixes.
- Some mpc51xx clock API cleanups in preparation for a clock API
overhaul
- A pile of cleanups of our old math emulation code, including better
support for using it to emulate optional FP instructions on
embedded chips that otherwise have a HW FPU.
- Some infrastructure in selftest, for powerpc now, but could be
generalized, initially used by some tests for our perf instruction
counting code.
- A pile of fixes for hotplug on pseries (that was seriously
bitrotting)
- The usual slew of freescale embedded updates, new boards, 64-bit
hiberation support, e6500 core PMU support, etc..."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (146 commits)
powerpc: Correct FSCR bit definitions
powerpc/xmon: Fix printing of set of CPUs in xmon
powerpc/pseries: Move lparcfg.c to platforms/pseries
powerpc/powernv: Return secondary CPUs to firmware on kexec
powerpc/btext: Fix CONFIG_PPC_EARLY_DEBUG_BOOTX on ppc32
powerpc: Cleanup handling of the DSCR bit in the FSCR register
powerpc/pseries: Child nodes are not detached by dlpar_detach_node
powerpc/pseries: Add mising of_node_put in delete_dt_node
powerpc/pseries: Make dlpar_configure_connector parent node aware
powerpc/pseries: Do all node initialization in dlpar_parse_cc_node
powerpc/pseries: Fix parsing of initial node path in update_dt_node
powerpc/pseries: Pack update_props_workarea to map correctly to rtas buffer header
powerpc/pseries: Fix over writing of rtas return code in update_dt_node
powerpc/pseries: Fix creation of loop in device node property list
powerpc: Skip emulating & leave interrupts off for kernel program checks
powerpc: Add more exception trampolines for hypervisor exceptions
powerpc: Fix location and rename exception trampolines
powerpc: Add more trap names to xmon
powerpc/pseries: Add a warning in the case of cross-cpu VPA registration
powerpc: Update the 00-Index in Documentation/powerpc
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
PCI device hotplug:
- Use PCIe native hotplug, not ACPI hotplug, when possible (Neil Horman)
- Assign resources on per-host bridge basis (Yinghai Lu)
MPS (Max Payload Size):
- Allow larger MPS settings below hotplug-capable Root Port (Yijing Wang)
- Add warnings about unsafe MPS settings (Yijing Wang)
- Simplify interface and messages (Bjorn Helgaas)
SR-IOV:
- Return -ENOSYS on non-SR-IOV devices (Stefan Assmann)
- Update NumVFs register when disabling SR-IOV (Yijing Wang)
Virtualization:
- Add bus and slot reset support (Alex Williamson)
- Fix ACS (Access Control Services) issues (Alex Williamson)
Miscellaneous:
- Simplify PCIe Capability accessors (Bjorn Helgaas)
- Add pcibios_pm_ops for arch-specific hibernate stuff (Sebastian Ott)
- Disable decoding during BAR sizing only when necessary (Zoltan Kiss)
- Delay enabling bridges until they're needed (Yinghai Lu)
- Split Designware support into Synopsys and Exynos parts (Jingoo Han)
- Convert class code to use dev_groups (Greg Kroah-Hartman)
- Cleanup Designware and Exynos I/O access wrappers (Seungwon Jeon)
- Fix bridge I/O window alignment (Bjorn Helgaas)
- Add pci_wait_for_pending_transaction() (Casey Leedom)
- Use devm_ioremap_resource() in Marvell driver (Tushar Behera)
* tag 'pci-v3.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (63 commits)
PCI/ACPI: Fix _OSC ordering to allow PCIe hotplug use when available
PCI: exynos: Add I/O access wrappers
PCI: designware: Drop "addr" arg from dw_pcie_readl_rc()/dw_pcie_writel_rc()
PCI: Remove pcie_cap_has_devctl()
PCI: Support PCIe Capability Slot registers only for ports with slots
PCI: Remove PCIe Capability version checks
PCI: Allow PCIe Capability link-related register access for switches
PCI: Add offsets of PCIe capability registers
PCI: Tidy bitmasks and spacing of PCIe capability definitions
PCI: Remove obsolete comment reference to pci_pcie_cap2()
PCI: Clarify PCI_EXP_TYPE_PCI_BRIDGE comment
PCI: Rename PCIe capability definitions to follow convention
PCI: Warn if unsafe MPS settings detected
PCI: Fix MPS peer-to-peer DMA comment syntax
PCI: Disable decoding for BAR sizing only when it was actually enabled
PCI: Add comment about needing pci_msi_off() even when CONFIG_PCI_MSI=n
PCI: Add pcibios_pm_ops for optional arch-specific hibernate functionality
PCI: Don't restrict MPS for slots below Root Ports
PCI: Simplify MPS test for Downstream Port
PCI: Remove unnecessary check for pcie_get_mps() failure
...
|
|
Based on a patch by Jon Mason (see URL below).
All users of pcie_bus_configure_settings() pass arguments of the form
"bus, bus->self->pcie_mpss". The "mpss" argument is redundant since we
can easily look it up internally. In addition, all callers check
"bus->self" for NULL, which we can also do internally.
This patch simplifies the interface and the callers. No functional change.
Reference: http://lkml.kernel.org/r/1317048850-30728-2-git-send-email-mason@myri.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
pci_read_bridge_bases() already checks if the PCI bus is root
bus or not, so we needn't do same check in pcibios_fixup_bus()
and just remove it.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Address some of the trivial sparse warnings in arch/powerpc.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
When EEH error happens to one specific PE, the device drivers
of its attached EEH devices (PCI devices) are checked to see
the further action: reset with complete hotplug, or reset without
hotplug. However, that's not enough for those PCI devices whose
drivers can't support EEH, or those PCI devices without driver.
So we need do so-called "partial hotplug" on basis of PCI devices.
In the situation, part of PCI devices of the specific PE are
unplugged and plugged again after PE reset.
The patch changes pcibios_add_pci_devices() so that it can support
full hotplug and so-called "partial" hotplug based on device-tree
or real hardware. It's notable that pci_of_scan.c has been changed
for a bit in order to support the "partial" hotplug based on dev-tree.
Most of the generic code already supports that, we just need to
plumb it properly on our side.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Commit 37f02195b (powerpc/pci: fix PCI-e devices rescan issue on powerpc
platform) fixes a problem with interrupt and DMA initialization on hot
plugged devices. With this commit, interrupt and DMA initialization for
hot plugged devices is handled in the pci device enable function.
This approach has a couple of drawbacks. First, it creates two code paths
for device initialization, one for hot plugged devices and another for devices
known during the initial PCI scan. Second, the initialization code for hot
plugged devices is only called when the device is enabled, ie typically
in the probe function. Also, the platform specific setup code is called each
time pci_enable_device() is called, not only once during device discovery,
meaning it is actually called multiple times, once for devices discovered
during the initial scan and again each time a driver is re-loaded.
The visible result is that interrupt pins are only assigned to hot plugged
devices when the device driver is loaded. Effectively this changes the PCI
probe API, since pci_dev->irq and the device's dma configuration will now
only be valid after pci_enable() was called at least once. A more subtle
change is that platform specific PCI device setup is moved from device
discovery into the driver's probe function, more specifically into the
pci_enable_device() call.
To fix the inconsistencies, add new function pcibios_add_device.
Call pcibios_setup_device from pcibios_setup_bus_devices if device setup
is not complete, and from pcibios_add_device if bus setup is complete.
With this change, device setup code is moved back into device initialization,
and called exactly once for both static and hot plugged devices.
[ This also fixes a regression introduced by the above patch which
causes dev->irq to be overwritten under some cirumstances after
MSIs have been enabled for the device which leads to crashes due
to the MSI core "hijacking" dev->irq to store the base MSI number
and not the LSI. --BenH
]
Cc: Yuanquan Chen <Yuanquan.Chen@freescale.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Hiroo Matsumoto <matsumoto.hiroo@jp.fujitsu.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
pcibios_fixup_resources
If a BAR has the value of 0, we would assume that it is unset yet and
then mark the resource as unset and would reassign it later. But after
commit 6c5705fe (powerpc/PCI: get rid of device resource fixups)
the pcibios_fixup_resources is invoked after the bus address was
translated to linux resource. So the value of res->start is resource
address. And since the resource and bus address may be different, we
should translate it to the bus address before doing the check.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The codes which ever used these two variables have gone. Throw away
them too.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
These comments already don't apply to the current code. So just remove
them.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The message is only meant to be displayed if resource 0 is empty,
but was displayed if any is.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The PCI core supports an offset per aperture nowadays but our arch
code still has a single offset per host bridge representing the
difference betwen CPU memory addresses and PCI MMIO addresses.
This is a problem as new machines and hypervisor versions are
coming out where the 64-bit windows will have a different offset
(basically mapped 1:1) from the 32-bit windows.
This fixes it by using separate offsets. In the long run, we probably
want to get rid of that intermediary struct pci_controller and have
those directly stored into the pci_host_bridge as they are parsed
but this will be a more invasive change.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
When converting to use the new pci_add_resource_offset() we didn't
properly account for empty resources (0 flags) and add those bogons
to the PHBs. The result is some annoying messages in the log.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
