| Age | Commit message (Collapse) | Author |
|---|
|
On pseries LPAR when an empty slot is assigned to partition OR in single
LPAR mode, kdump kernel crashes during issuing PHB reset.
In the kdump scenario, we traverse all PHBs and issue reset using the
pe_config_addr of the first child device present under each PHB. However
the code assumes that none of the PHB slots can be empty and uses
list_first_entry() to get the first child device under the PHB. Since
list_first_entry() expects the list to be non-empty, it returns an
invalid pci_dn entry and ends up accessing NULL phb pointer under
pci_dn->phb causing kdump kernel crash.
This patch fixes the below kdump kernel crash by skipping empty slots:
audit: initializing netlink subsys (disabled)
thermal_sys: Registered thermal governor 'fair_share'
thermal_sys: Registered thermal governor 'step_wise'
cpuidle: using governor menu
pstore: Registered nvram as persistent store backend
Issue PHB reset ...
audit: type=2000 audit(1631267818.000:1): state=initialized audit_enabled=0 res=1
BUG: Kernel NULL pointer dereference on read at 0x00000268
Faulting instruction address: 0xc000000008101fb0
Oops: Kernel access of bad area, sig: 7 [#1]
LE PAGE_SIZE=64K MMU=Radix SMP NR_CPUS=2048 NUMA pSeries
Modules linked in:
CPU: 7 PID: 1 Comm: swapper/7 Not tainted 5.14.0 #1
NIP: c000000008101fb0 LR: c000000009284ccc CTR: c000000008029d70
REGS: c00000001161b840 TRAP: 0300 Not tainted (5.14.0)
MSR: 8000000002009033 <SF,VEC,EE,ME,IR,DR,RI,LE> CR: 28000224 XER: 20040002
CFAR: c000000008101f0c DAR: 0000000000000268 DSISR: 00080000 IRQMASK: 0
...
NIP pseries_eeh_get_pe_config_addr+0x100/0x1b0
LR __machine_initcall_pseries_eeh_pseries_init+0x2cc/0x350
Call Trace:
0xc00000001161bb80 (unreliable)
__machine_initcall_pseries_eeh_pseries_init+0x2cc/0x350
do_one_initcall+0x60/0x2d0
kernel_init_freeable+0x350/0x3f8
kernel_init+0x3c/0x17c
ret_from_kernel_thread+0x5c/0x64
Fixes: 5a090f7c363fd ("powerpc/pseries: PCIE PHB reset")
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.ibm.com>
[mpe: Tweak wording and trim oops]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/163215558252.413351.8600189949820258982.stgit@jupiter
|
|
The IPR drivers tests for MSI support at probe time with MSI vector 0
and when done, frees the IRQ with free_irq(). This test was introduced
by 95fecd90397e ("ipr: add test for MSI interrupt support") as an
improvement of commit 5a9ef25b14d3 ("[SCSI] ipr: add MSI support")
because a boot failure was reported on a Bimini PowerPC system:
https://lore.kernel.org/r/1242926159.3007.5.camel@localhost.localdomain
It was finally decided to remove MSI support on Bimini systems in
6eb0ac03899a ("powerpc/maple: Add a quirk to disable MSI for IPR on
Bimini").
Linux 5.15-rc1 added MSI domain support to the pseries machine and
when free_irq is called() in the driver, msi_domain_deactivate() also
is. This resets the MSI table entry of the associate vector by calling
__pci_write_msi_msg() with an empty message and breaks any further
activation of the same vector. In the case of the IPR driver, it
breaks the initialization sequence of the IOA.
Introduce an empty irq_write_msi_msg() handler in the MSI domain of
the pseries machine to avoid clearing the MSI vector entry. Updating
the entry is not strictly necessary since it is initialized by the
underlying hypervisor, PowerVM or QEMU/KVM.
Fixes: a5f3d2c17b07 ("powerpc/pseries/pci: Add MSI domains")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Tested-by: Mahesh Salgaonkar <mahesh@linux.ibm.com>
[mpe: Tweak comment wording and formatting slightly]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210930102535.1047230-1-clg@kaod.org
|
|
Merge more updates from Andrew Morton:
"147 patches, based on 7d2a07b769330c34b4deabeed939325c77a7ec2f.
Subsystems affected by this patch series: mm (memory-hotplug, rmap,
ioremap, highmem, cleanups, secretmem, kfence, damon, and vmscan),
alpha, percpu, procfs, misc, core-kernel, MAINTAINERS, lib,
checkpatch, epoll, init, nilfs2, coredump, fork, pids, criu, kconfig,
selftests, ipc, and scripts"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (94 commits)
scripts: check_extable: fix typo in user error message
mm/workingset: correct kernel-doc notations
ipc: replace costly bailout check in sysvipc_find_ipc()
selftests/memfd: remove unused variable
Kconfig.debug: drop selecting non-existing HARDLOCKUP_DETECTOR_ARCH
configs: remove the obsolete CONFIG_INPUT_POLLDEV
prctl: allow to setup brk for et_dyn executables
pid: cleanup the stale comment mentioning pidmap_init().
kernel/fork.c: unexport get_{mm,task}_exe_file
coredump: fix memleak in dump_vma_snapshot()
fs/coredump.c: log if a core dump is aborted due to changed file permissions
nilfs2: use refcount_dec_and_lock() to fix potential UAF
nilfs2: fix memory leak in nilfs_sysfs_delete_snapshot_group
nilfs2: fix memory leak in nilfs_sysfs_create_snapshot_group
nilfs2: fix memory leak in nilfs_sysfs_delete_##name##_group
nilfs2: fix memory leak in nilfs_sysfs_create_##name##_group
nilfs2: fix NULL pointer in nilfs_##name##_attr_release
nilfs2: fix memory leak in nilfs_sysfs_create_device_group
trap: cleanup trap_init()
init: move usermodehelper_enable() to populate_rootfs()
...
|
|
There is only a single user remaining. We can simply lookup the nid only
used for node offlining purposes when walking our memory blocks. We don't
expect to remove multi-nid ranges; and if we'd ever do, we most probably
don't care about removing multi-nid ranges that actually result in empty
nodes.
If ever required, we can detect the "multi-nid" scenario and simply try
offlining all online nodes.
Link: https://lkml.kernel.org/r/20210712124052.26491-4-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Nathan Lynch <nathanl@linux.ibm.com>
Cc: Laurent Dufour <ldufour@linux.ibm.com>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.ibm.com>
Cc: Scott Cheloha <cheloha@linux.ibm.com>
Cc: Anton Blanchard <anton@ozlabs.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Baoquan He <bhe@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jia He <justin.he@arm.com>
Cc: Joe Perches <joe@perches.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Michel Lespinasse <michel@lespinasse.org>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Pankaj Gupta <pankaj.gupta@ionos.com>
Cc: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Pierre Morel <pmorel@linux.ibm.com>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Rich Felker <dalias@libc.org>
Cc: Sergei Trofimovich <slyfox@gentoo.org>
Cc: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Wei Yang <richard.weiyang@linux.alibaba.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Convert pseries & powernv to use MSI IRQ domains.
- Rework the pseries CPU numbering so that CPUs that are removed, and
later re-added, are given a CPU number on the same node as
previously, when possible.
- Add support for a new more flexible device-tree format for specifying
NUMA distances.
- Convert powerpc to GENERIC_PTDUMP.
- Retire sbc8548 and sbc8641d board support.
- Various other small features and fixes.
Thanks to Alexey Kardashevskiy, Aneesh Kumar K.V, Anton Blanchard,
Cédric Le Goater, Christophe Leroy, Emmanuel Gil Peyrot, Fabiano Rosas,
Fangrui Song, Finn Thain, Gautham R. Shenoy, Hari Bathini, Joel
Stanley, Jordan Niethe, Kajol Jain, Laurent Dufour, Leonardo Bras, Lukas
Bulwahn, Marc Zyngier, Masahiro Yamada, Michal Suchanek, Nathan
Chancellor, Nicholas Piggin, Parth Shah, Paul Gortmaker, Pratik R.
Sampat, Randy Dunlap, Sebastian Andrzej Siewior, Srikar Dronamraju, Wan
Jiabing, Xiongwei Song, and Zheng Yongjun.
* tag 'powerpc-5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (154 commits)
powerpc/bug: Cast to unsigned long before passing to inline asm
powerpc/ptdump: Fix generic ptdump for 64-bit
KVM: PPC: Fix clearing never mapped TCEs in realmode
powerpc/pseries/iommu: Rename "direct window" to "dma window"
powerpc/pseries/iommu: Make use of DDW for indirect mapping
powerpc/pseries/iommu: Find existing DDW with given property name
powerpc/pseries/iommu: Update remove_dma_window() to accept property name
powerpc/pseries/iommu: Reorganize iommu_table_setparms*() with new helper
powerpc/pseries/iommu: Add ddw_property_create() and refactor enable_ddw()
powerpc/pseries/iommu: Allow DDW windows starting at 0x00
powerpc/pseries/iommu: Add ddw_list_new_entry() helper
powerpc/pseries/iommu: Add iommu_pseries_alloc_table() helper
powerpc/kernel/iommu: Add new iommu_table_in_use() helper
powerpc/pseries/iommu: Replace hard-coded page shift
powerpc/numa: Update cpu_cpu_map on CPU online/offline
powerpc/numa: Print debug statements only when required
powerpc/numa: convert printk to pr_xxx
powerpc/numa: Drop dbg in favour of pr_debug
powerpc/smp: Enable CACHE domain for shared processor
powerpc/smp: Update cpu_core_map on all PowerPc systems
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb
Pull swiotlb updates from Konrad Rzeszutek Wilk:
"A new feature called restricted DMA pools. It allows SWIOTLB to
utilize per-device (or per-platform) allocated memory pools instead of
using the global one.
The first big user of this is ARM Confidential Computing where the
memory for DMA operations can be set per platform"
* 'stable/for-linus-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb: (23 commits)
swiotlb: use depends on for DMA_RESTRICTED_POOL
of: restricted dma: Don't fail device probe on rmem init failure
of: Move of_dma_set_restricted_buffer() into device.c
powerpc/svm: Don't issue ultracalls if !mem_encrypt_active()
s390/pv: fix the forcing of the swiotlb
swiotlb: Free tbl memory in swiotlb_exit()
swiotlb: Emit diagnostic in swiotlb_exit()
swiotlb: Convert io_default_tlb_mem to static allocation
of: Return success from of_dma_set_restricted_buffer() when !OF_ADDRESS
swiotlb: add overflow checks to swiotlb_bounce
swiotlb: fix implicit debugfs declarations
of: Add plumbing for restricted DMA pool
dt-bindings: of: Add restricted DMA pool
swiotlb: Add restricted DMA pool initialization
swiotlb: Add restricted DMA alloc/free support
swiotlb: Refactor swiotlb_tbl_unmap_single
swiotlb: Move alloc_size to swiotlb_find_slots
swiotlb: Use is_swiotlb_force_bounce for swiotlb data bouncing
swiotlb: Update is_swiotlb_active to add a struct device argument
swiotlb: Update is_swiotlb_buffer to add a struct device argument
...
|
|
Merge misc updates from Andrew Morton:
"173 patches.
Subsystems affected by this series: ia64, ocfs2, block, and mm (debug,
pagecache, gup, swap, shmem, memcg, selftests, pagemap, mremap,
bootmem, sparsemem, vmalloc, kasan, pagealloc, memory-failure,
hugetlb, userfaultfd, vmscan, compaction, mempolicy, memblock,
oom-kill, migration, ksm, percpu, vmstat, and madvise)"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (173 commits)
mm/madvise: add MADV_WILLNEED to process_madvise()
mm/vmstat: remove unneeded return value
mm/vmstat: simplify the array size calculation
mm/vmstat: correct some wrong comments
mm/percpu,c: remove obsolete comments of pcpu_chunk_populated()
selftests: vm: add COW time test for KSM pages
selftests: vm: add KSM merging time test
mm: KSM: fix data type
selftests: vm: add KSM merging across nodes test
selftests: vm: add KSM zero page merging test
selftests: vm: add KSM unmerge test
selftests: vm: add KSM merge test
mm/migrate: correct kernel-doc notation
mm: wire up syscall process_mrelease
mm: introduce process_mrelease system call
memblock: make memblock_find_in_range method private
mm/mempolicy.c: use in_task() in mempolicy_slab_node()
mm/mempolicy: unify the create() func for bind/interleave/prefer-many policies
mm/mempolicy: advertise new MPOL_PREFERRED_MANY
mm/hugetlb: add support for mempolicy MPOL_PREFERRED_MANY
...
|
|
With CONFIG_SPARSEMEM_EXTREME enabled, __section_nr() which converts
mem_section to section_nr could be costly since it iterates all section
roots to check if the given mem_section is in its range.
On the other hand, __nr_to_section() which converts section_nr to
mem_section can be done in O(1).
Let's pass section_nr instead of mem_section ptr to find_memory_block() in
order to reduce needless iterations.
Link: https://lkml.kernel.org/r/20210707150212.855-3-ohoono.kwon@samsung.com
Signed-off-by: Ohhoon Kwon <ohoono.kwon@samsung.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Merge our fixes branch into next.
That lets us resolve a conflict in arch/powerpc/sysdev/xive/common.c.
Between cbc06f051c52 ("powerpc/xive: Do not skip CPU-less nodes when
creating the IPIs"), which moved request_irq() out of xive_init_ipis(),
and 17df41fec5b8 ("powerpc: use IRQF_NO_DEBUG for IPIs") which added
IRQF_NO_DEBUG to that request_irq() call, which has now moved.
|
|
Pull dma-mapping updates from Christoph Hellwig:
- fix debugfs initialization order (Anthony Iliopoulos)
- use memory_intersects() directly (Kefeng Wang)
- allow to return specific errors from ->map_sg (Logan Gunthorpe,
Martin Oliveira)
- turn the dma_map_sg return value into an unsigned int (me)
- provide a common global coherent pool іmplementation (me)
* tag 'dma-mapping-5.15' of git://git.infradead.org/users/hch/dma-mapping: (31 commits)
hexagon: use the generic global coherent pool
dma-mapping: make the global coherent pool conditional
dma-mapping: add a dma_init_global_coherent helper
dma-mapping: simplify dma_init_coherent_memory
dma-mapping: allow using the global coherent pool for !ARM
ARM/nommu: use the generic dma-direct code for non-coherent devices
dma-direct: add support for dma_coherent_default_memory
dma-mapping: return an unsigned int from dma_map_sg{,_attrs}
dma-mapping: disallow .map_sg operations from returning zero on error
dma-mapping: return error code from dma_dummy_map_sg()
x86/amd_gart: don't set failed sg dma_address to DMA_MAPPING_ERROR
x86/amd_gart: return error code from gart_map_sg()
xen: swiotlb: return error code from xen_swiotlb_map_sg()
parisc: return error code from .map_sg() ops
sparc/iommu: don't set failed sg dma_address to DMA_MAPPING_ERROR
sparc/iommu: return error codes from .map_sg() ops
s390/pci: don't set failed sg dma_address to DMA_MAPPING_ERROR
s390/pci: return error code from s390_dma_map_sg()
powerpc/iommu: don't set failed sg dma_address to DMA_MAPPING_ERROR
powerpc/iommu: return error code from .map_sg() ops
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big set of driver core patches for 5.15-rc1.
These do change a number of different things across different
subsystems, and because of that, there were 2 stable tags created that
might have already come into your tree from different pulls that did
the following
- changed the bus remove callback to return void
- sysfs iomem_get_mapping rework
Other than those two things, there's only a few small things in here:
- kernfs performance improvements for huge numbers of sysfs users at
once
- tiny api cleanups
- other minor changes
All of these have been in linux-next for a while with no reported
problems, other than the before-mentioned merge issue"
* tag 'driver-core-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (33 commits)
MAINTAINERS: Add dri-devel for component.[hc]
driver core: platform: Remove platform_device_add_properties()
ARM: tegra: paz00: Handle device properties with software node API
bitmap: extend comment to bitmap_print_bitmask/list_to_buf
drivers/base/node.c: use bin_attribute to break the size limitation of cpumap ABI
topology: use bin_attribute to break the size limitation of cpumap ABI
lib: test_bitmap: add bitmap_print_bitmask/list_to_buf test cases
cpumask: introduce cpumap_print_list/bitmask_to_buf to support large bitmask and list
sysfs: Rename struct bin_attribute member to f_mapping
sysfs: Invoke iomem_get_mapping() from the sysfs open callback
debugfs: Return error during {full/open}_proxy_open() on rmmod
zorro: Drop useless (and hardly used) .driver member in struct zorro_dev
zorro: Simplify remove callback
sh: superhyway: Simplify check in remove callback
nubus: Simplify check in remove callback
nubus: Make struct nubus_driver::remove return void
kernfs: dont call d_splice_alias() under kernfs node lock
kernfs: use i_lock to protect concurrent inode updates
kernfs: switch kernfs to use an rwsem
kernfs: use VFS negative dentry caching
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"Updates to the interrupt core and driver subsystems:
Core changes:
- The usual set of small fixes and improvements all over the place,
but nothing stands out
MSI changes:
- Further consolidation of the PCI/MSI interrupt chip code
- Make MSI sysfs code independent of PCI/MSI and expose the MSI
interrupts of platform devices in the same way as PCI exposes them.
Driver changes:
- Support for ARM GICv3 EPPI partitions
- Treewide conversion to generic_handle_domain_irq() for all chained
interrupt controllers
- Conversion to bitmap_zalloc() throughout the irq chip drivers
- The usual set of small fixes and improvements"
* tag 'irq-core-2021-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (57 commits)
platform-msi: Add ABI to show msi_irqs of platform devices
genirq/msi: Move MSI sysfs handling from PCI to MSI core
genirq/cpuhotplug: Demote debug printk to KERN_DEBUG
irqchip/qcom-pdc: Trim unused levels of the interrupt hierarchy
irqdomain: Export irq_domain_disconnect_hierarchy()
irqchip/gic-v3: Fix priority comparison when non-secure priorities are used
irqchip/apple-aic: Fix irq_disable from within irq handlers
pinctrl/rockchip: drop the gpio related codes
gpio/rockchip: drop irq_gc_lock/irq_gc_unlock for irq set type
gpio/rockchip: support next version gpio controller
gpio/rockchip: use struct rockchip_gpio_regs for gpio controller
gpio/rockchip: add driver for rockchip gpio
dt-bindings: gpio: change items restriction of clock for rockchip,gpio-bank
pinctrl/rockchip: add pinctrl device to gpio bank struct
pinctrl/rockchip: separate struct rockchip_pin_bank to a head file
pinctrl/rockchip: always enable clock for gpio controller
genirq: Fix kernel doc indentation
EDAC/altera: Convert to generic_handle_domain_irq()
powerpc: Bulk conversion to generic_handle_domain_irq()
nios2: Bulk conversion to generic_handle_domain_irq()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates from Marc Zyngier:
- API updates:
- Treewide conversion to generic_handle_domain_irq() for anything
that looks like a chained interrupt controller
- Update the irqdomain documentation
- Use of bitmap_zalloc() throughout the tree
- New functionalities:
- Support for GICv3 EPPI partitions
- Fixes:
- Qualcomm PDC hierarchy fixes
- Yet another priority decoding fix for the GICv3 pseudo-NMIs
- Fix the apple-aic driver irq_eoi() callback to always unmask
the interrupt
- Properly handle edge interrupts on loongson-pch-pic
- Let the mtk-sysirq driver advertise IRQCHIP_SKIP_SET_WAKE
Link: https://lore.kernel.org/r/20210828121013.2647964-1-maz@kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix scv implicit soft-mask table for relocated (eg. kdump) kernels
- Re-enable ARCH_ENABLE_SPLIT_PMD_PTLOCK, which was disabled due to a
typo
Thanks to Lukas Bulwahn, Nicholas Piggin, and Daniel Axtens.
* tag 'powerpc-5.14-7' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64s: Fix scv implicit soft-mask table for relocated kernels
powerpc: Re-enable ARCH_ENABLE_SPLIT_PMD_PTLOCK
|
|
A previous change introduced the usage of DDW as a bigger indirect DMA
mapping when the DDW available size does not map the whole partition.
As most of the code that manipulates direct mappings was reused for
indirect mappings, it's necessary to rename all names and debug/info
messages to reflect that it can be used for both kinds of mapping.
This should cause no behavioural change, just adjust naming.
Signed-off-by: Leonardo Bras <leobras.c@gmail.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210817063929.38701-12-leobras.c@gmail.com
|
|
So far it's assumed possible to map the guest RAM 1:1 to the bus, which
works with a small number of devices. SRIOV changes it as the user can
configure hundreds VFs and since phyp preallocates TCEs and does not
allow IOMMU pages bigger than 64K, it has to limit the number of TCEs
per a PE to limit waste of physical pages.
As of today, if the assumed direct mapping is not possible, DDW creation
is skipped and the default DMA window "ibm,dma-window" is used instead.
By using DDW, indirect mapping can get more TCEs than available for the
default DMA window, and also get access to using much larger pagesizes
(16MB as implemented in qemu vs 4k from default DMA window), causing a
significant increase on the maximum amount of memory that can be IOMMU
mapped at the same time.
Indirect mapping will only be used if direct mapping is not a
possibility.
For indirect mapping, it's necessary to re-create the iommu_table with
the new DMA window parameters, so iommu_alloc() can use it.
Removing the default DMA window for using DDW with indirect mapping
is only allowed if there is no current IOMMU memory allocated in
the iommu_table. enable_ddw() is aborted otherwise.
Even though there won't be both direct and indirect mappings at the
same time, we can't reuse the DIRECT64_PROPNAME property name, or else
an older kexec()ed kernel can assume direct mapping, and skip
iommu_alloc(), causing undesirable behavior.
So a new property name DMA64_PROPNAME "linux,dma64-ddr-window-info"
was created to represent a DDW that does not allow direct mapping.
Signed-off-by: Leonardo Bras <leobras.c@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210817063929.38701-11-leobras.c@gmail.com
|
|
At the moment pseries stores information about created directly mapped
DDW window in DIRECT64_PROPNAME.
With the objective of implementing indirect DMA mapping with DDW, it's
necessary to have another propriety name to make sure kexec'ing into older
kernels does not break, as it would if we reuse DIRECT64_PROPNAME.
In order to have this, find_existing_ddw_windows() needs to be able to
look for different property names.
Extract find_existing_ddw_windows() into find_existing_ddw_windows_named()
and calls it with current property name.
Signed-off-by: Leonardo Bras <leobras.c@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210817063929.38701-10-leobras.c@gmail.com
|
|
Update remove_dma_window() so it can be used to remove DDW with a given
property name.
This enables the creation of new property names for DDW, so we can
have different usage for it, like indirect mapping.
Also, add return values to it so we can check if the property was found
while removing the active DDW. This allows skipping the remaining property
names while reducing the impact of multiple property names.
Signed-off-by: Leonardo Bras <leobras.c@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210817063929.38701-9-leobras.c@gmail.com
|
|
Add a new helper _iommu_table_setparms(), and use it in
iommu_table_setparms() and iommu_table_setparms_lpar() to avoid duplicated
code.
Also, setting tbl->it_ops was happening outsite iommu_table_setparms*(),
so move it to the new helper. Since we need the iommu_table_ops to be
declared before used, declare iommu_table_lpar_multi_ops and
iommu_table_pseries_ops to before their respective iommu_table_setparms*().
Signed-off-by: Leonardo Bras <leobras.c@gmail.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210817063929.38701-8-leobras.c@gmail.com
|
|
Code used to create a ddw property that was previously scattered in
enable_ddw() is now gathered in ddw_property_create(), which deals with
allocation and filling the property, letting it ready for
of_property_add(), which now occurs in sequence.
This created an opportunity to reorganize the second part of enable_ddw():
Without this patch enable_ddw() does, in order:
kzalloc() property & members, create_ddw(), fill ddwprop inside property,
ddw_list_new_entry(), do tce_setrange_multi_pSeriesLP_walk in all memory,
of_add_property(), and list_add().
With this patch enable_ddw() does, in order:
create_ddw(), ddw_property_create(), of_add_property(),
ddw_list_new_entry(), do tce_setrange_multi_pSeriesLP_walk in all memory,
and list_add().
This change requires of_remove_property() in case anything fails after
of_add_property(), but we get to do tce_setrange_multi_pSeriesLP_walk
in all memory, which looks the most expensive operation, only if
everything else succeeds.
Also, the error path got remove_ddw() replaced by a new helper
__remove_dma_window(), which only removes the new DDW with an rtas-call.
For this, a new helper clean_dma_window() was needed to clean anything
that could left if walk_system_ram_range() fails.
Signed-off-by: Leonardo Bras <leobras.c@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210817063929.38701-7-leobras.c@gmail.com
|
|
enable_ddw() currently returns the address of the DMA window, which is
considered invalid if has the value 0x00.
Also, it only considers valid an address returned from find_existing_ddw
if it's not 0x00.
Changing this behavior makes sense, given the users of enable_ddw() only
need to know if direct mapping is possible. It can also allow a DMA window
starting at 0x00 to be used.
This will be helpful for using a DDW with indirect mapping, as the window
address will be different than 0x00, but it will not map the whole
partition.
Signed-off-by: Leonardo Bras <leobras.c@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210817063929.38701-6-leobras.c@gmail.com
|
|
There are two functions creating direct_window_list entries in a
similar way, so create a ddw_list_new_entry() to avoid duplicity and
simplify those functions.
Signed-off-by: Leonardo Bras <leobras.c@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210817063929.38701-5-leobras.c@gmail.com
|
|
Creates a helper to allow allocating a new iommu_table without the need
to reallocate the iommu_group.
This will be helpful for replacing the iommu_table for the new DMA window,
after we remove the old one with iommu_tce_table_put().
Signed-off-by: Leonardo Bras <leobras.c@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210817063929.38701-4-leobras.c@gmail.com
|
|
Some functions assume IOMMU page size can only be 4K (pageshift == 12).
Update them to accept any page size passed, so we can use 64K pages.
In the process, some defines like TCE_SHIFT were made obsolete, and then
removed.
IODA3 Revision 3.0_prd1 (OpenPowerFoundation), Figures 3.4 and 3.5 show
a RPN of 52-bit, and considers a 12-bit pageshift, so there should be
no need of using TCE_RPN_MASK, which masks out any bit after 40 in rpn.
It's usage removed from tce_build_pSeries(), tce_build_pSeriesLP(), and
tce_buildmulti_pSeriesLP().
Most places had a tbl struct, so using tbl->it_page_shift was simple.
tce_free_pSeriesLP() was a special case, since callers not always have a
tbl struct, so adding a tceshift parameter seems the right thing to do.
Signed-off-by: Leonardo Bras <leobras.c@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210817063929.38701-2-leobras.c@gmail.com
|
|
Merge the changes to retire the legacy WR sbc8548 and sbc8641 platforms
from Paul. These were sent as a pull request, but I rebased them onto
rc2 so as not to pull too many unrelated changes in to my next.
Description from Paul's pull request follows:
In v2.6.27 (2008, 917f0af9e5a9) the sbc8260 support was implicitly
retired by not being carried forward through the ppc --> powerpc
device tree transition.
Then, in v3.6 (2012, b048b4e17cbb) we retired the support for the
sbc8560 boards.
Next, in v4.18 (2017, 3bc6cf5a86e5) we retired the support for the
2006 vintage sbc834x boards.
The sbc8548 and sbc8641d boards were maybe 1-2 years newer than the
sbc834x boards, but it is also 3+ years later, so it makes sense to
now retire them as well - which is what is done here.
These two remaining WR boards were based on the Freescale MPC8548-CDS
and the MPC8641D-HPCN reference board implementations. Having had the
chance to use these and many other Fsl ref boards, I know this: The
Freescale reference boards were typically produced in limited quantity
and primarily available to BSP developers and hardware designers, and
not likely to have found a 2nd life with hobbyists and/or collectors.
It was good to have that BSP code subjected to mainline review and
hence also widely available back in the day. But given the above, we
should probably also be giving serious consideration to retiring
additional similar age/type reference board platforms as well.
I've always felt it is important for us to be proactive in retiring
old code, since it has a genuine non-zero carrying cost, as described
in the 930d52c012b8 merge log. But for the here and now, we just
clean up the remaining BSP code that I had added for SBC platforms.
Link: https://lore.kernel.org/r/20210824174209.GB160508@windriver.com
|
|
The support was for this was added to mainline over 12 years ago, in
v2.6.26 [4e8aae89a35d] just around the ppc --> powerpc migration.
I believe the board was introduced shortly after the sbc8548 board,
making it roughly a 14 year old platform - with the CPU speed and
memory size typical for that era.
I haven't had one of these boards for several years, and availability
was discontinued several years before that.
Given that, there is no point in adding a burden to testing coverage
that builds all possible defconfigs, so it makes sense to remove it.
Of course it will remain in the git history forever, for anyone who
happens to find a functional board and wants to tinker with it.
Acked-by: Scott Wood <oss@buserror.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The support was for this was mainlined 13 years ago, in v2.6.25
[0e0fffe88767] just around the ppc --> powerpc migration.
I believe the board was introduced a year or two before that, so it
is roughly a 15 year old platform - with the CPU speed and memory size
that was typical for that era.
I haven't had one of these boards for several years, and availability
was discontinued several years before that.
Given that, there is no point in adding a burden to testing coverage
that builds all possible defconfigs, so it makes sense to remove it.
Of course it will remain in the git history forever, for anyone who
happens to find a functional board and wants to tinker with it.
Acked-by: Scott Wood <oss@buserror.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Merge some KVM patches we are keeping in a topic branch in case there
are any merge conflicts that need resolving.
|
|
40x and BOOKE don't have MSR_RI therefore all tests involving
MSR_RI may be problematic on those plateforms.
Create helpers to check or set MSR_RI in regs, and use them
in common code.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/c2fb93708196734f4176dda334aaa3055f213b89.1629707037.git.christophe.leroy@csgroup.eu
|
|
Create an anonymous union for dsisr and esr regsiters, we can reference
esr to get the exception detail when CONFIG_4xx=y or CONFIG_BOOKE=y.
Otherwise, reference dsisr. This makes code more clear.
Signed-off-by: Xiongwei Song <sxwjean@gmail.com>
[mpe: Reword commit title]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210807010239.416055-2-sxwjean@me.com
|
|
This register is not architected and not implemented in POWER9 or 10,
it just reads back zeroes for compatibility.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Link: https://lore.kernel.org/r/20210811160134.904987-11-npiggin@gmail.com
|
|
This fixes a compile error with W=1.
Fixes: 6d0aaf5e0de0 ("powerpc/pseries/vas: Setup IRQ and fault handling")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210819125656.14498-3-clg@kaod.org
|
|
Commit 66f24fa766e3 ("mm: drop redundant ARCH_ENABLE_SPLIT_PMD_PTLOCK")
broke PMD split page table lock for powerpc.
It selects the non-existent config ARCH_ENABLE_PMD_SPLIT_PTLOCK in
arch/powerpc/platforms/Kconfig.cputype, but clearly intended to
select ARCH_ENABLE_SPLIT_PMD_PTLOCK (notice the word swapping!), as
that commit did for all other architectures.
Fix it by selecting the correct symbol ARCH_ENABLE_SPLIT_PMD_PTLOCK.
Fixes: 66f24fa766e3 ("mm: drop redundant ARCH_ENABLE_SPLIT_PMD_PTLOCK")
Cc: stable@vger.kernel.org # v5.13+
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Daniel Axtens <dja@axtens.net>
[mpe: Reword change log to make it clear this is a bug fix]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210819113954.17515-3-lukas.bulwahn@gmail.com
|
|
As reported by lkp, if NUMA=n we see a build error:
arch/powerpc/platforms/pseries/hotplug-cpu.c: In function 'pseries_cpu_hotplug_init':
arch/powerpc/platforms/pseries/hotplug-cpu.c:1022:8: error: 'node_to_cpumask_map' undeclared
1022 | node_to_cpumask_map[node]);
Use cpumask_of_node() which has an empty stub for NUMA=n, and when
NUMA=y does a lookup from node_to_cpumask_map[].
Fixes: bd1dd4c5f528 ("powerpc/pseries: Prevent free CPU ids being reused on another node")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210816041032.2839343-1-mpe@ellerman.id.au
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix crashes coming out of nap on 32-bit Book3s (eg. powerbooks).
- Fix critical and debug interrupts on BookE, seen as crashes when
using ptrace.
- Fix an oops when running an SMP kernel on a UP system.
- Update pseries LPAR security flavor after partition migration.
- Fix an oops when using kprobes on BookE.
- Fix oops on 32-bit pmac by not calling do_IRQ() from
timer_interrupt().
- Fix softlockups on CPU hotplug into a CPU-less node with xive (P9).
Thanks to Cédric Le Goater, Christophe Leroy, Finn Thain, Geetika
Moolchandani, Laurent Dufour, Laurent Vivier, Nicholas Piggin, Pu Lehui,
Radu Rendec, Srikar Dronamraju, and Stan Johnson.
* tag 'powerpc-5.14-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/xive: Do not skip CPU-less nodes when creating the IPIs
powerpc/interrupt: Do not call single_step_exception() from other exceptions
powerpc/interrupt: Fix OOPS by not calling do_IRQ() from timer_interrupt()
powerpc/kprobes: Fix kprobe Oops happens in booke
powerpc/pseries: Fix update of LPAR security flavor after LPM
powerpc/smp: Fix OOPS in topology_init()
powerpc/32: Fix critical and debug interrupts on BOOKE
powerpc/32s: Fix napping restore in data storage interrupt (DSI)
|
|
PAPR interface currently supports two different ways of communicating resource
grouping details to the OS. These are referred to as Form 0 and Form 1
associativity grouping. Form 0 is the older format and is now considered
deprecated. This patch adds another resource grouping named FORM2.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210812132223.225214-6-aneesh.kumar@linux.ibm.com
|
|
This helper is only used with the dispatch trace log collection.
A later patch will add Form2 affinity support and this change helps
in keeping that simpler. Also add a comment explaining we don't expect
the code to be called with FORM0
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210812132223.225214-5-aneesh.kumar@linux.ibm.com
|
|
The associativity details of the newly added resourced are collected from
the hypervisor via "ibm,configure-connector" rtas call. Update the numa
distance details of the newly added numa node after the above call.
Instead of updating NUMA distance every time we lookup a node id
from the associativity property, add helpers that can be used
during boot which does this only once. Also remove the distance
update from node id lookup helpers.
Currently, we duplicate parsing code for ibm,associativity and
ibm,associativity-lookup-arrays in the kernel. The associativity array provided
by these device tree properties are very similar and hence can use
a helper to parse the node id and numa distance details.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210812132223.225214-4-aneesh.kumar@linux.ibm.com
|
|
Also make related code cleanup that will allow adding FORM2_AFFINITY in
later patches. No functional change in this patch.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210812132223.225214-3-aneesh.kumar@linux.ibm.com
|
|
No functional change in this patch. arch_debugfs_dir is the generic kernel
name declared in linux/debugfs.h for arch-specific debugfs directory.
Architectures like x86/s390 already use the name. Rename powerpc
specific powerpc_debugfs_root to arch_debugfs_dir.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210812132831.233794-2-aneesh.kumar@linux.ibm.com
|
|
Wherever possible, replace constructs that match either
generic_handle_irq(irq_find_mapping()) or
generic_handle_irq(irq_linear_revmap()) to a single call to
generic_handle_domain_irq().
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
Wherever possible, replace constructs that match either
generic_handle_irq(irq_find_mapping()) or
generic_handle_irq(irq_linear_revmap()) to a single call to
generic_handle_domain_irq().
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210802162630.2219813-13-maz@kernel.org
|
|
pnv_opal_pci_msi_eoi() is called from KVM to EOI passthrough interrupts
when in real mode. Adding MSI domain broke the hack using the
'ioda.irq_chip' field to deduce the owning PHB. Fix that by using the
IRQ chip data in the MSI domain.
The 'ioda.irq_chip' field is now unused and could be removed from the
pnv_phb struct.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210701132750.1475580-30-clg@kaod.org
|
|
Before MSI domains, the default IRQ chip of PHB3 MSIs was patched by
pnv_set_msi_irq_chip() with the custom EOI handler pnv_ioda2_msi_eoi()
and the owning PHB was deduced from the 'ioda.irq_chip' field. This
path has been deprecated by the MSI domains but it is still in use by
the P8 CAPI 'cxl' driver.
Rewriting this driver to support MSI would be a waste of time.
Nevertheless, we can still remove the IRQ chip patch and set the IRQ
chip data instead. This is cleaner.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210701132750.1475580-29-clg@kaod.org
|
|
The pnv_ioda2_msi_eoi() chip handler is not used anymore for MSIs.
Simply use the check on the PSI-MSI chip.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210701132750.1475580-27-clg@kaod.org
|
|
MSIs should be fully managed by the PCI and IRQ subsystems now.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210701132750.1475580-26-clg@kaod.org
|
|
MSIs should be fully managed by the PCI and IRQ subsystems now.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210701132750.1475580-25-clg@kaod.org
|
|
The PowerNV and pSeries platforms now have support for both the XICS
and XIVE IRQ domains.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210701132750.1475580-23-clg@kaod.org
|
|
PHB3s need an extra OPAL call to EOI the interrupt. The call takes an
OPAL HW IRQ number but it is translated into a vector number in OPAL.
Here, we directly use the vector number of the in-the-middle "PNV-MSI"
domain instead of grabbing the OPAL HW IRQ number in the XICS parent
domain.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210701132750.1475580-22-clg@kaod.org
|
|
Passthrough PCI MSI interrupts are detected in KVM with a check on a
specific EOI handler (P8) or on XIVE (P9). We can now check the
PCI-MSI IRQ chip which is cleaner.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210701132750.1475580-14-clg@kaod.org
|
