| Age | Commit message (Collapse) | Author |
|---|
|
Conflicts:
include/linux/compiler-clang.h
include/linux/compiler-gcc.h
include/linux/compiler-intel.h
include/uapi/linux/stddef.h
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
to READ_ONCE()/WRITE_ONCE()
Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.
However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:
----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()
// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Memory hot unplug on PowerNV radix hosts is broken. Our memory block
size is 256MB but since we map the linear region with very large
pages, each pte we tear down maps 1GB.
A hot unplug of one 256MB memory block results in 768MB of memory
getting unintentionally unmapped. At this point we are likely to oops.
Fix this by increasing our memory block size to 1GB on PowerNV radix
hosts.
Fixes: 4b5d62ca17a1 ("powerpc/mm: add radix__remove_section_mapping()")
Cc: stable@vger.kernel.org # v4.11+
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
A reference to the parent device node is held by add_dt_node() for the
node to be added. If the call to dlpar_configure_connector() fails
add_dt_node() returns ENOENT and that reference is not freed.
Add a call to of_node_put(parent_dn) prior to bailing out after a
failed dlpar_configure_connector() call.
Fixes: 8d5ff320766f ("powerpc/pseries: Make dlpar_configure_connector parent node aware")
Cc: stable@vger.kernel.org # v3.12+
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Commit 215ee763f8cb ("powerpc: pseries: remove dlpar_attach_node
dependency on full path") reworked dlpar_attach_node() to no longer
look up the parent node "/cpus", but instead to have the parent node
passed by the caller in the function parameter list.
As a result dlpar_attach_node() is no longer responsible for freeing
the reference to the parent node. However, commit 215ee763f8cb failed
to remove the of_node_put(parent) call in dlpar_attach_node(), or to
take into account that the reference to the parent in the caller
dlpar_cpu_add() needs to be held until after dlpar_attach_node()
returns.
As a result doing repeated cpu add/remove dlpar operations will
eventually result in the following error:
OF: ERROR: Bad of_node_put() on /cpus
CPU: 0 PID: 10896 Comm: drmgr Not tainted 4.13.0-autotest #1
Call Trace:
dump_stack+0x15c/0x1f8 (unreliable)
of_node_release+0x1a4/0x1c0
kobject_put+0x1a8/0x310
kobject_del+0xbc/0xf0
__of_detach_node_sysfs+0x144/0x210
of_detach_node+0xf0/0x180
dlpar_detach_node+0xc4/0x120
dlpar_cpu_remove+0x280/0x560
dlpar_cpu_release+0xbc/0x1b0
arch_cpu_release+0x6c/0xb0
cpu_release_store+0xa0/0x100
dev_attr_store+0x68/0xa0
sysfs_kf_write+0xa8/0xf0
kernfs_fop_write+0x2cc/0x400
__vfs_write+0x5c/0x340
vfs_write+0x1a8/0x3d0
SyS_write+0xa8/0x1a0
system_call+0x58/0x6c
Fix the issue by removing the of_node_put(parent) call from
dlpar_attach_node(), and ensuring that the reference to the parent
node is properly held and released by the caller dlpar_cpu_add().
Fixes: 215ee763f8cb ("powerpc: pseries: remove dlpar_attach_node dependency on full path")
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
[mpe: Add a comment in the code and frob the change log slightly]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Commit 24be85a23d1f ("powerpc/powernv: Clear PECE1 in LPCR via
stop-api only on Hotplug") clears the PECE1 bit of the LPCR via
stop-api during CPU-Hotplug to prevent wakeup due to a decrementer on
an offlined CPU which is in a deep stop state.
In the case where the stop-api support is found to be lacking, the
commit 785a12afdb4a ("powerpc/powernv/idle: Disable LOSE_FULL_CONTEXT
states when stop-api fails") disables deep states that lose hypervisor
context. Thus in this case, the offlined CPU will be put to some
shallow idle state.
However, we currently unconditionally clear the PECE1 in LPCR via
stop-api during CPU-Hotplug even when deep states are disabled due to
stop-api failure.
Fix this by clearing PECE1 of LPCR via stop-api during CPU-Hotplug
*only* when the offlined CPU will be put to a deep state that loses
hypervisor context.
Fixes: 24be85a23d1f ("powerpc/powernv: Clear PECE1 in LPCR via stop-api only on Hotplug")
Reported-by: Pavithra Prakash <pavirampu@linux.vnet.ibm.com>
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Tested-by: Pavithra Prakash <pavrampu@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
GFP_TEMPORARY was introduced by commit e12ba74d8ff3 ("Group short-lived
and reclaimable kernel allocations") along with __GFP_RECLAIMABLE. It's
primary motivation was to allow users to tell that an allocation is
short lived and so the allocator can try to place such allocations close
together and prevent long term fragmentation. As much as this sounds
like a reasonable semantic it becomes much less clear when to use the
highlevel GFP_TEMPORARY allocation flag. How long is temporary? Can the
context holding that memory sleep? Can it take locks? It seems there is
no good answer for those questions.
The current implementation of GFP_TEMPORARY is basically GFP_KERNEL |
__GFP_RECLAIMABLE which in itself is tricky because basically none of
the existing caller provide a way to reclaim the allocated memory. So
this is rather misleading and hard to evaluate for any benefits.
I have checked some random users and none of them has added the flag
with a specific justification. I suspect most of them just copied from
other existing users and others just thought it might be a good idea to
use without any measuring. This suggests that GFP_TEMPORARY just
motivates for cargo cult usage without any reasoning.
I believe that our gfp flags are quite complex already and especially
those with highlevel semantic should be clearly defined to prevent from
confusion and abuse. Therefore I propose dropping GFP_TEMPORARY and
replace all existing users to simply use GFP_KERNEL. Please note that
SLAB users with shrinkers will still get __GFP_RECLAIMABLE heuristic and
so they will be placed properly for memory fragmentation prevention.
I can see reasons we might want some gfp flag to reflect shorterm
allocations but I propose starting from a clear semantic definition and
only then add users with proper justification.
This was been brought up before LSF this year by Matthew [1] and it
turned out that GFP_TEMPORARY really doesn't have a clear semantic. It
seems to be a heuristic without any measured advantage for most (if not
all) its current users. The follow up discussion has revealed that
opinions on what might be temporary allocation differ a lot between
developers. So rather than trying to tweak existing users into a
semantic which they haven't expected I propose to simply remove the flag
and start from scratch if we really need a semantic for short term
allocations.
[1] http://lkml.kernel.org/r/20170118054945.GD18349@bombadil.infradead.org
[akpm@linux-foundation.org: fix typo]
[akpm@linux-foundation.org: coding-style fixes]
[sfr@canb.auug.org.au: drm/i915: fix up]
Link: http://lkml.kernel.org/r/20170816144703.378d4f4d@canb.auug.org.au
Link: http://lkml.kernel.org/r/20170728091904.14627-1-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Mel Gorman <mgorman@suse.de>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Neil Brown <neilb@suse.de>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Nothing really major this release, despite quite a lot of activity.
Just lots of things all over the place.
Some things of note include:
- Access via perf to a new type of PMU (IMC) on Power9, which can
count both core events as well as nest unit events (Memory
controller etc).
- Optimisations to the radix MMU TLB flushing, mostly to avoid
unnecessary Page Walk Cache (PWC) flushes when the structure of the
tree is not changing.
- Reworks/cleanups of do_page_fault() to modernise it and bring it
closer to other architectures where possible.
- Rework of our page table walking so that THP updates only need to
send IPIs to CPUs where the affected mm has run, rather than all
CPUs.
- The size of our vmalloc area is increased to 56T on 64-bit hash MMU
systems. This avoids problems with the percpu allocator on systems
with very sparse NUMA layouts.
- STRICT_KERNEL_RWX support on PPC32.
- A new sched domain topology for Power9, to capture the fact that
pairs of cores may share an L2 cache.
- Power9 support for VAS, which is a new mechanism for accessing
coprocessors, and initial support for using it with the NX
compression accelerator.
- Major work on the instruction emulation support, adding support for
many new instructions, and reworking it so it can be used to
implement the emulation needed to fixup alignment faults.
- Support for guests under PowerVM to use the Power9 XIVE interrupt
controller.
And probably that many things again that are almost as interesting,
but I had to keep the list short. Plus the usual fixes and cleanups as
always.
Thanks to: Alexey Kardashevskiy, Alistair Popple, Andreas Schwab,
Aneesh Kumar K.V, Anju T Sudhakar, Arvind Yadav, Balbir Singh,
Benjamin Herrenschmidt, Bhumika Goyal, Breno Leitao, Bryant G. Ly,
Christophe Leroy, Cédric Le Goater, Dan Carpenter, Dou Liyang,
Frederic Barrat, Gautham R. Shenoy, Geliang Tang, Geoff Levand, Hannes
Reinecke, Haren Myneni, Ivan Mikhaylov, John Allen, Julia Lawall,
LABBE Corentin, Laurentiu Tudor, Madhavan Srinivasan, Markus Elfring,
Masahiro Yamada, Matt Brown, Michael Neuling, Murilo Opsfelder Araujo,
Nathan Fontenot, Naveen N. Rao, Nicholas Piggin, Oliver O'Halloran,
Paul Mackerras, Rashmica Gupta, Rob Herring, Rui Teng, Sam Bobroff,
Santosh Sivaraj, Scott Wood, Shilpasri G Bhat, Sukadev Bhattiprolu,
Suraj Jitindar Singh, Tobin C. Harding, Victor Aoqui"
* tag 'powerpc-4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (321 commits)
powerpc/xive: Fix section __init warning
powerpc: Fix kernel crash in emulation of vector loads and stores
powerpc/xive: improve debugging macros
powerpc/xive: add XIVE Exploitation Mode to CAS
powerpc/xive: introduce H_INT_ESB hcall
powerpc/xive: add the HW IRQ number under xive_irq_data
powerpc/xive: introduce xive_esb_write()
powerpc/xive: rename xive_poke_esb() in xive_esb_read()
powerpc/xive: guest exploitation of the XIVE interrupt controller
powerpc/xive: introduce a common routine xive_queue_page_alloc()
powerpc/sstep: Avoid used uninitialized error
axonram: Return directly after a failed kzalloc() in axon_ram_probe()
axonram: Improve a size determination in axon_ram_probe()
axonram: Delete an error message for a failed memory allocation in axon_ram_probe()
powerpc/powernv/npu: Move tlb flush before launching ATSD
powerpc/macintosh: constify wf_sensor_ops structures
powerpc/iommu: Use permission-specific DEVICE_ATTR variants
powerpc/eeh: Delete an error out of memory message at init time
powerpc/mm: Use seq_putc() in two functions
macintosh: Convert to using %pOF instead of full_name
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux
Pull writeback error handling updates from Jeff Layton:
"This pile continues the work from last cycle on better tracking
writeback errors. In v4.13 we added some basic errseq_t infrastructure
and converted a few filesystems to use it.
This set continues refining that infrastructure, adds documentation,
and converts most of the other filesystems to use it. The main
exception at this point is the NFS client"
* tag 'wberr-v4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux:
ecryptfs: convert to file_write_and_wait in ->fsync
mm: remove optimizations based on i_size in mapping writeback waits
fs: convert a pile of fsync routines to errseq_t based reporting
gfs2: convert to errseq_t based writeback error reporting for fsync
fs: convert sync_file_range to use errseq_t based error-tracking
mm: add file_fdatawait_range and file_write_and_wait
fuse: convert to errseq_t based error tracking for fsync
mm: consolidate dax / non-dax checks for writeback
Documentation: add some docs for errseq_t
errseq: rename __errseq_set to errseq_set
|
|
This is the framework for using XIVE in a PowerVM guest. The support
is very similar to the native one in a much simpler form.
Each source is associated with an Event State Buffer (ESB). This is a
two bit state machine which is used to trigger events. The bits are
named "P" (pending) and "Q" (queued) and can be controlled by MMIO.
The Guest OS registers event (or notifications) queues on which the HW
will post event data for a target to notify.
Instead of OPAL calls, a set of Hypervisors call are used to configure
the interrupt sources and the event/notification queues of the guest:
- H_INT_GET_SOURCE_INFO
used to obtain the address of the MMIO page of the Event State
Buffer (PQ bits) entry associated with the source.
- H_INT_SET_SOURCE_CONFIG
assigns a source to a "target".
- H_INT_GET_SOURCE_CONFIG
determines to which "target" and "priority" is assigned to a source
- H_INT_GET_QUEUE_INFO
returns the address of the notification management page associated
with the specified "target" and "priority".
- H_INT_SET_QUEUE_CONFIG
sets or resets the event queue for a given "target" and "priority".
It is also used to set the notification config associated with the
queue, only unconditional notification for the moment. Reset is
performed with a queue size of 0 and queueing is disabled in that
case.
- H_INT_GET_QUEUE_CONFIG
returns the queue settings for a given "target" and "priority".
- H_INT_RESET
resets all of the partition's interrupt exploitation structures to
their initial state, losing all configuration set via the hcalls
H_INT_SET_SOURCE_CONFIG and H_INT_SET_QUEUE_CONFIG.
- H_INT_SYNC
issue a synchronisation on a source to make sure sure all
notifications have reached their queue.
As for XICS, the XIVE interface for the guest is described in the
device tree under the "interrupt-controller" node. A couple of new
properties are specific to XIVE :
- "reg"
contains the base address and size of the thread interrupt
managnement areas (TIMA), also called rings, for the User level and
for the Guest OS level. Only the Guest OS level is taken into
account today.
- "ibm,xive-eq-sizes"
the size of the event queues. One cell per size supported, contains
log2 of size, in ascending order.
- "ibm,xive-lisn-ranges"
the interrupt numbers ranges assigned to the guest. These are
allocated using a simple bitmap.
and also :
- "/ibm,plat-res-int-priorities"
contains a list of priorities that the hypervisor has reserved for
its own use.
Tested with a QEMU XIVE model for pseries and with the Power hypervisor.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The nest MMU tlb flush needs to happen before the GPU translation
shootdown is launched to avoid the GPU refilling its tlb with stale
nmmu translations prior to the nmmu flush completing.
Fixes: 1ab66d1fbada ("powerpc/powernv: Introduce address translation services for Nvlink2")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Calls to mmu_notifier_invalidate_page() were replaced by calls to
mmu_notifier_invalidate_range() and now are bracketed by calls to
mmu_notifier_invalidate_range_start()/end()
Remove now useless invalidate_page callback.
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Alistair Popple <alistair@popple.id.au>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
assigned lmbs
Check if an LMB is assigned before attempting to call dlpar_acquire_drc
in order to avoid any unnecessary rtas calls. This substantially
reduces the running time of memory hot add on lpars with large amounts
of memory.
[mpe: We need to explicitly set rc to 0 in the success case, otherwise
the compiler might think we use rc without initialising it.]
Fixes: c21f515c7436 ("powerpc/pseries: Make the acquire/release of the drc for memory a seperate step")
Cc: stable@vger.kernel.org # v4.11+
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
struct platform_suspend_ops are not supposed to change at runtime.
Functions suspend_set_ops working with const platform_suspend_ops. So
mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
.llong is an undocumented PPC specific directive. The generic
equivalent is .quad, but even better (because it's self describing) is
.8byte.
Convert all .llong directives to .8byte.
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Remove unneeded variables and assignments.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Define interfaces (wrappers) to the 'copy' and 'paste'
instructions (which are new in PowerISA 3.0). These are intended to be
used to by NX driver(s) to submit Coprocessor Request Blocks (CRBs) to
the NX hardware engines.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Define an interface to open a VAS send window. This interface is
intended to be used the Nest Accelerator (NX) driver(s) to open
a send window and use it to submit compression/encryption requests
to a VAS receive window.
The receive window, identified by the [vasid, cop] parameters, must
already be open in VAS (i.e connected to an NX engine).
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Define the vas_win_close() interface which should be used to close a
send or receive windows.
While the hardware configurations required to open send and receive
windows differ, the configuration to close a window is the same for
both. So we use a single interface to close the window.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Define the vas_rx_win_open() interface. This interface is intended to
be used by the Nest Accelerator (NX) driver(s) to setup receive
windows for one or more NX engines (which implement compression &
encryption algorithms in the hardware).
Follow-on patches will provide an interface to close the window and to
open a send window that kernel subsystems can use to access the NX
engines.
The interface to open a receive window is expected to be invoked for
each instance of VAS in the system.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Define helpers to allocate/free VAS window objects. These will be used
in follow-on patches when opening/closing windows.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Define helpers to initialize window context registers of the VAS
hardware. These will be used in follow-on patches when opening/closing
VAS windows.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Define some helper functions to access the MMIO regions. We use these
in follow-on patches to read/write VAS hardware registers. They are
also used to later issue 'paste' instructions to submit requests to
the NX hardware engines.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Implement vas_init() and vas_exit() functions for a new VAS module.
This VAS module is essentially a library for other device drivers
and kernel users of the NX coprocessors like NX-842 and NX-GZIP.
In the future this will be extended to add support for user space
to access the NX coprocessors.
VAS is currently only supported with 64K page size.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Define macros for the VAS hardware registers and bit-fields as well
as couple of data structures needed by the VAS driver.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
[mpe: Fixup include guard to use _ASM_POWERPC_VAS_H]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The check_req() helper uses pci_get_pdn() to get an OF node pointer.
pci_get_pdn() returns a pci_dn pointer which either:
1) from the OF node returned by pci_device_to_OF_node();
2) from the parent child_list where entries don't have OF node pointers.
Since check_req() does not care about 2), it can call
pci_device_to_OF_node() directly, hence the change.
The find_pe_dn() helper uses embedded pci_dn to get an OF node which is
also stored in edev->pdev so let's take a shortcut and call
pci_device_to_OF_node() directly.
With these 2 changes, we can finally get rid of the OF node back pointer.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The eeh_dev struct hold a config space address of an associated node
and the very same address is also stored in the pci_dn struct which
is always present during the eeh_dev lifetime.
This uses bus:devfn directly from pci_dn instead of cached and packed
config_addr.
Since config_addr is made from device's bus:dev.fn, there is no point
in keeping it in the debugfs either so remove that too.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The eeh_dev struct already holds a pointer to pci_dn which it does not
exist without and pci_dn itself holds the very same pointer so just
use it.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
arch/powerpc/kernel/eeh_dev.c:57 is the only legit place where edev
is allocated; other 2 places allocate it on stack and in the heap for
a very short period of time to use eeh_pe_get() as takes edev.
This changes eeh_pe_get() to receive required parameters explicitly.
This removes unnecessary temporary allocation of edev.
This uses the "pe_no" name instead of the "pe_config_addr" name as
it actually is a PE number and not a config space address as it seemed.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
clk_div_tables are not supposed to change at runtime.
mpc512x_clk_divtable function working with const clk_div_table. So
mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
There is a cut and paste error here so we use sizeof(struct mpc83xx_pmc)
to remap the memory for "clock_regs". That sizeof() is 20 bytes and we
only need to remap 12 bytes. It presumably doesn't affect run time too
much...
I changed them to both use sizeof(*variable_name) because that's the
preferred kernel style these days.
Fixes: d49747bdfb2d ("powerpc/mpc83xx: Power Management support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
[mpe: It will map at least one page anyway, but still a good cleanup]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
There are quite a few machine check exceptions that can be caused by
kernel bugs. To make debugging easier, use the kernel crash path in
cases of synchronous machine checks that occur in kernel mode, if that
would not result in the machine going straight to panic or crash dump.
There is a downside here that die()ing the process in kernel mode can
still leave the system unstable. panic_on_oops will always force the
system to fail-stop, so systems where that behaviour is important will
still do the right thing.
As a test, when triggering an i-side 0111b error (ifetch from foreign
address) in kernel mode process context on POWER9, the kernel currently
dies quickly like this:
Severe Machine check interrupt [Not recovered]
NIP [ffff000000000000]: 0xffff000000000000
Initiator: CPU
Error type: Real address [Instruction fetch (foreign)]
[ 127.426651616,0] OPAL: Reboot requested due to Platform error.
Effective[ 127.426693712,3] OPAL: Reboot requested due to Platform error. address: ffff000000000000
opal: Reboot type 1 not supported
Kernel panic - not syncing: PowerNV Unrecovered Machine Check
CPU: 56 PID: 4425 Comm: syscall Tainted: G M 4.12.0-rc1-13857-ga4700a261072-dirty #35
Call Trace:
[ 128.017988928,4] IPMI: BUG: Dropping ESEL on the floor due to
buggy/mising code in OPAL for this BMC
Rebooting in 10 seconds..
Trying to free IRQ 496 from IRQ context!
After this patch, the process is killed and the kernel continues with
this message, which gives enough information to identify the offending
branch (i.e., with CFAR):
Severe Machine check interrupt [Not recovered]
NIP [ffff000000000000]: 0xffff000000000000
Initiator: CPU
Error type: Real address [Instruction fetch (foreign)]
Effective address: ffff000000000000
Oops: Machine check, sig: 7 [#1]
SMP NR_CPUS=2048
NUMA
PowerNV
Modules linked in: iptable_mangle ipt_MASQUERADE nf_nat_masquerade_ipv4 ...
CPU: 22 PID: 4436 Comm: syscall Tainted: G M 4.12.0-rc1-13857-ga4700a261072-dirty #36
task: c000000932300000 task.stack: c000000932380000
NIP: ffff000000000000 LR: 00000000217706a4 CTR: ffff000000000000
REGS: c00000000fc8fd80 TRAP: 0200 Tainted: G M (4.12.0-rc1-13857-ga4700a261072-dirty)
MSR: 90000000001c1003 <SF,HV,ME,RI,LE>
CR: 24000484 XER: 20000000
CFAR: c000000000004c80 DAR: 0000000021770a90 DSISR: 0a000000 SOFTE: 1
GPR00: 0000000000001ebe 00007fffce4818b0 0000000021797f00 0000000000000000
GPR04: 00007fff8007ac24 0000000044000484 0000000000004000 00007fff801405e8
GPR08: 900000000280f033 0000000024000484 0000000000000000 0000000000000030
GPR12: 9000000000001003 00007fff801bc370 0000000000000000 0000000000000000
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR24: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR28: 00007fff801b0000 0000000000000000 00000000217707a0 00007fffce481918
NIP [ffff000000000000] 0xffff000000000000
LR [00000000217706a4] 0x217706a4
Call Trace:
Instruction dump:
XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Unrecovered MCE and HMI errors are sent through a special restart OPAL
call to log the platform error. The downside is that they don't go
through normal Linux crash paths, so they don't give much information
to the Linux console.
Change this by providing a special crash function which does some of
the console flushing from the panic() path before calling firmware to
reboot.
The downside of this is a little more code to execute before reaching
the firmware reboot. However in practice, it's critical to get the
Linux console messages output in order to debug a problem. So this is
a desirable tradeoff.
Note on the implementation: It is difficult to plumb a custom reboot
handler into the panic path, because panic does a little bit too much
work. For example, it will try to delay with the timebase, but that
may be corrupted in some cases resulting in a hang without reaching
the platform reboot. Another problem is that panic can invoke the
crash dump code which is not what we want in the case of a hardware
platform error. Long-term the best solution will be to rework the
panic path so it can be suitable for this kind of panic, but for now
we just duplicate a bit of the code.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Some PowerVM firmware when delivering a system reset interrupt to a
little endian OS will mess up SRR registers. They are byteswapped, and
SRR1 is incorrect. An example from a crash:
NIP: 14dd0900000000c0
MSR: 1000000200000080
It's possible to detect this pattern in SRR1 (that would never happen
in normal operation), and at least fix the NIP. After this patch, the
same interrupt reports NIP properly:
NIP [c00000000009dd14] plpar_hcall_norets+0x1c/0x28
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
If fadump is not registered, and no other crash or debug handlers are
registered, the powerpc panic handler stops the guest before the
generic panic code can push out debug information to the console.
Currently, system reset injection causes the guest to silently stop.
Stop calling ppc_md.panic in the panic notifier. crash_fadump already
does rtas_os_term() to terminate the guest if fadump is registered.
Remove ppc_md.panic. Move fadump panic notifier into fadump code.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Remove incorrect comment about real mode address restrictions on
powernv (bare metal), and unnecessary clamping to ppc64_rma_size.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
When building a random powerpc kernel I hit this build error:
arch/powerpc/platforms/powernv/opal-imc.c:130:13: error : assignment
discards « const » qualifier from pointer target type
[-Werror=discarded-qualifiers]
l_cpumask = cpumask_of_node(nid);
^
This happens because when CONFIG_NUMA=n cpumask_of_node() returns a
const pointer.
This patch simply adds const to l_cpumask to fix this issue.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
[mpe: Flesh out change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The hardware trace macro feature requires access to a chunk of real
memory. This patch provides a debugfs interface to do this. By
writing an integer containing the size of memory to be unplugged into
/sys/kernel/debug/powerpc/memtrace/enable, the code will attempt to
remove that much memory from the end of each NUMA node.
This patch also adds additional debugsfs files for each node that
allows the tracer to interact with the removed memory, as well as
a trace file that allows userspace to read the generated trace.
Note that this patch does not invoke the hardware trace macro, it
only allows memory to be removed during runtime for the trace macro
to utilise.
Signed-off-by: Rashmica Gupta <rashmica.g@gmail.com>
[mpe: Minor formatting etc fixups]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
In preparation to stop storing the full node path in full_name, remove the
dependency on full_name from dlpar_attach_node(). Callers of
dlpar_attach_node() already have the parent device_node, so just pass the
parent node into dlpar_attach_node instead of the path. This avoids doing
a lookup of the parent node by the path.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Scott Wood <oss@buserror.net>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linuxppc-dev@lists.ozlabs.org
Reviewed-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Currently in the vio.c code we use a comparision against the parent
device node's full path to decide if the device is a PFO or VIO family
device.
Both the ibm,platform-facilities and vdevice nodes are defined by PAPR,
and must have a matching device_type. So instead of using the path we
can instead compare the device_type.
I've checked Qemu and kvmtool both do this correctly, and all the
PowerVM systems I have access to do also. So it seems to be safe.
This removes the dependency on full_name, which is being removed
upstream.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
There's a non-trivial dependency between some commits we want to put in
next and the KVM prefetch work around that went into fixes. So merge
fixes into next.
|
|
Declare bin_attribute structures as const as they are only passed as an
argument to the function sysfs_create_bin_file. This argument is of
type const, so declare the structure as const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Normally the values in the resource field and the argument to ARRAY_SIZE
in the num_resources are the same. In this case, the value in the reousrce
field is the same as the one in the previous platform_device structure, and
appears to be a copy-paste error. Replace the value in the resource field
with the argument to the local call to ARRAY_SIZE.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Commit 968159c0031ac ("powerpc/8xx: Getting rid of remaining use of
CONFIG_8xx") removed all but 2 references to 8xx in Kconfigs.
This patch removes the two remaining ones.
Fixes: 968159c0031a ("powerpc/8xx: Getting rid of remaining use of CONFIG_8xx")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Two config options exist to define powerpc MPC8xx:
* CONFIG_PPC_8xx
* CONFIG_8xx
arch/powerpc/platforms/Kconfig.cputype has contained the following
comment about CONFIG_8xx item for some years:
"# this is temp to handle compat with arch=ppc"
There is no more users of CONFIG_8xx, so remove it.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Two config options exist to define powerpc MPC8xx:
* CONFIG_PPC_8xx
* CONFIG_8xx
arch/powerpc/platforms/Kconfig.cputype has contained the following
comment about CONFIG_8xx item for some years:
"# this is temp to handle compat with arch=ppc"
arch/powerpc is now the only place with remaining use of
CONFIG_8xx: get rid of them.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
mpc8xx_pic.c is dedicated to the 8xx, so move it to platform/8xx
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
In the same spirit as what was done for 4xx and 44x, move
the 8xx machine check into platforms/8xx
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
