| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
- fix the fu540-c000 device tree to avoid a schema check failure on the
DMA node name
- fix typo in the PolarFire SOC device tree
* tag 'riscv-for-linus-5.18-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: dts: microchip: fix gpio1 reg property typo
riscv: dts: sifive: fu540-c000: align dma node name with dtschema
|
|
Fix reg address typo in the gpio1 stanza.
Signed-off-by: Conor Paxton <conor.paxton@microchip.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Fixes: 528a5b1f2556 ("riscv: dts: microchip: add new peripherals to icicle kit device tree")
Link: https://lore.kernel.org/r/20220517104058.2004734-1-conor.paxton@microchip.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
Fixes dtbs_check warnings like:
dma@3000000: $nodename:0: 'dma@3000000' does not match '^dma-controller(@.*)?$'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20220407193856.18223-1-krzysztof.kozlowski@linaro.org
Fixes: c5ab54e9945b ("riscv: dts: add support for PDMA device of HiFive Unleashed Rev A00")
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fix from Palmer Dabbelt:
- A fix to relocate the DTB early in boot, in cases where the
bootloader doesn't put the DTB in a region that will end up
mapped by the kernel.
This manifests as a crash early in boot on a handful of
configurations.
* tag 'riscv-for-linus-5.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
RISC-V: relocate DTB if it's outside memory region
|
|
Pull kvm fixes from Paolo Bonzini:
"ARM:
- Take care of faults occuring between the PARange and IPA range by
injecting an exception
- Fix S2 faults taken from a host EL0 in protected mode
- Work around Oops caused by a PMU access from a 32bit guest when PMU
has been created. This is a temporary bodge until we fix it for
good.
x86:
- Fix potential races when walking host page table
- Fix shadow page table leak when KVM runs nested
- Work around bug in userspace when KVM synthesizes leaf 0x80000021
on older (pre-EPYC) or Intel processors
Generic (but affects only RISC-V):
- Fix bad user ABI for KVM_EXIT_SYSTEM_EVENT"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: work around QEMU issue with synthetic CPUID leaves
Revert "x86/mm: Introduce lookup_address_in_mm()"
KVM: x86/mmu: fix potential races when walking host page table
KVM: fix bad user ABI for KVM_EXIT_SYSTEM_EVENT
KVM: x86/mmu: Do not create SPTEs for GFNs that exceed host.MAXPHYADDR
KVM: arm64: Inject exception on out-of-IPA-range translation fault
KVM/arm64: Don't emulate a PMU for 32-bit guests if feature not set
KVM: arm64: Handle host stage-2 faults from 32-bit EL0
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A semi-large pile of clk driver fixes this time around.
Nothing is touching the core so these fixes are fairly well contained
to specific devices that use these clk drivers.
- Some Allwinner SoC fixes to gracefully handle errors and mark an
RTC clk as critical so that the RTC keeps ticking.
- Fix AXI bus clks and RTC clk design for Microchip PolarFire SoC
driver introduced this cycle. This has some devicetree bits acked
by riscv maintainers. We're fixing it now so that the prior
bindings aren't released in a major kernel version.
- Remove a reset on Microchip PolarFire SoCs that broke when enabling
CONFIG_PM.
- Set a min/max for the Qualcomm graphics clk. This got broken by the
clk rate range patches introduced this cycle"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: sunxi: sun9i-mmc: check return value after calling platform_get_resource()
clk: sunxi-ng: sun6i-rtc: Mark rtc-32k as critical
riscv: dts: microchip: reparent mpfs clocks
clk: microchip: mpfs: add RTCREF clock control
clk: microchip: mpfs: re-parent the configurable clocks
dt-bindings: rtc: add refclk to mpfs-rtc
dt-bindings: clk: mpfs: add defines for two new clocks
dt-bindings: clk: mpfs document msspll dri registers
riscv: dts: microchip: fix usage of fic clocks on mpfs
clk: microchip: mpfs: mark CLK_ATHENA as critical
clk: microchip: mpfs: fix parents for FIC clocks
clk: qcom: clk-rcg2: fix gfx3d frequency calculation
clk: microchip: mpfs: don't reset disabled peripherals
clk: sunxi-ng: fix not NULL terminated coccicheck error
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
- A fix to properly ensure a single CPU is running during patch_text().
- A defconfig update to include RPMSG_CTRL when RPMSG_CHAR was set,
necessary after a recent refactoring.
* tag 'riscv-for-linus-5.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
RISC-V: configs: Configs that had RPMSG_CHAR now get RPMSG_CTRL
riscv: patch_text: Fixup last cpu should be master
|
|
Fixes for (relatively) old bugs, to be merged in both the -rc and next
development trees:
* Fix potential races when walking host page table
* Fix bad user ABI for KVM_EXIT_SYSTEM_EVENT
* Fix shadow page table leak when KVM runs nested
|
|
When KVM_EXIT_SYSTEM_EVENT was introduced, it included a flags
member that at the time was unused. Unfortunately this extensibility
mechanism has several issues:
- x86 is not writing the member, so it would not be possible to use it
on x86 except for new events
- the member is not aligned to 64 bits, so the definition of the
uAPI struct is incorrect for 32- on 64-bit userspace. This is a
problem for RISC-V, which supports CONFIG_KVM_COMPAT, but fortunately
usage of flags was only introduced in 5.18.
Since padding has to be introduced, place a new field in there
that tells if the flags field is valid. To allow further extensibility,
in fact, change flags to an array of 16 values, and store how many
of the values are valid. The availability of the new ndata field
is tied to a system capability; all architectures are changed to
fill in the field.
To avoid breaking compilation of userspace that was using the flags
field, provide a userspace-only union to overlap flags with data[0].
The new field is placed at the same offset for both 32- and 64-bit
userspace.
Cc: Will Deacon <will@kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Peter Gonda <pgonda@google.com>
Cc: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reported-by: kernel test robot <lkp@intel.com>
Message-Id: <20220422103013.34832-1-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
In case the DTB provided by the bootloader/BootROM is before the kernel
image or outside /memory, we won't be able to access it through the
linear mapping, and get a segfault on setup_arch(). Currently OpenSBI
relocates DTB but that's not always the case (e.g. if FW_JUMP_FDT_ADDR
is not specified), and it's also not the most portable approach since
the default FW_JUMP_FDT_ADDR of the generic platform relocates the DTB
at a specific offset that may not be available. To avoid this situation
copy DTB so that it's visible through the linear mapping.
Signed-off-by: Nick Kossifidis <mick@ics.forth.gr>
Link: https://lore.kernel.org/r/20220322132839.3653682-1-mick@ics.forth.gr
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Fixes: f105aa940e78 ("riscv: add BUILTIN_DTB support for MMU-enabled targets")
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
In the commit 617d32938d1b ("rpmsg: Move the rpmsg control device
from rpmsg_char to rpmsg_ctrl"), we split the rpmsg_char driver in two.
By default give everyone who had the old driver enabled the rpmsg_ctrl
driver too.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Link: https://lore.kernel.org/r/20220404090527.582217-1-arnaud.pouliquen@foss.st.com
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
The 600M clock in the fabric is not the real reference, replace it with
a 125M clock which is the correct value for the icicle kit. Rename the
msspllclk node to mssrefclk since this is now the input to, not the
output of, the msspll clock. Control of the msspll clock has been moved
into the clock configurator, so add the register range for it to the clk
configurator. Finally, add a new output of the clock config block which
will provide the 1M reference clock for the MTIMER and the rtc.
Fixes: 528a5b1f2556 ("riscv: dts: microchip: add new peripherals to icicle kit device tree")
Fixes: 0fa6107eca41 ("RISC-V: Initial DTS for Microchip ICICLE board")
Reviewed-by: Daire McNamara <daire.mcnamara@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220413075835.3354193-10-conor.dooley@microchip.com
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The fic clocks passed to the pcie controller and other peripherals in
the device tree are not the clocks they actually run on. The fics are
actually clock domain crossers & the clock config blocks output is the
mss/cpu side input to the interconnect. The peripherals are actually
clocked by fixed frequency clocks embedded in the fpga fabric.
Fix the device tree so that these peripherals use the correct clocks.
The fabric side FIC0 & FIC1 inputs both use the same 125 MHz, so only
one clock is created for them.
Fixes: 528a5b1f2556 ("riscv: dts: microchip: add new peripherals to icicle kit device tree")
Reviewed-by: Daire McNamara <daire.mcnamara@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220413075835.3354193-4-conor.dooley@microchip.com
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Pull kvm fixes from Paolo Bonzini:
"The main and larger change here is a workaround for AMD's lack of
cache coherency for encrypted-memory guests.
I have another patch pending, but it's waiting for review from the
architecture maintainers.
RISC-V:
- Remove 's' & 'u' as valid ISA extension
- Do not allow disabling the base extensions 'i'/'m'/'a'/'c'
x86:
- Fix NMI watchdog in guests on AMD
- Fix for SEV cache incoherency issues
- Don't re-acquire SRCU lock in complete_emulated_io()
- Avoid NULL pointer deref if VM creation fails
- Fix race conditions between APICv disabling and vCPU creation
- Bugfixes for disabling of APICv
- Preserve BSP MSR_KVM_POLL_CONTROL across suspend/resume
selftests:
- Do not use bitfields larger than 32-bits, they differ between GCC
and clang"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: selftests: introduce and use more page size-related constants
kvm: selftests: do not use bitfields larger than 32-bits for PTEs
KVM: SEV: add cache flush to solve SEV cache incoherency issues
KVM: SVM: Flush when freeing encrypted pages even on SME_COHERENT CPUs
KVM: SVM: Simplify and harden helper to flush SEV guest page(s)
KVM: selftests: Silence compiler warning in the kvm_page_table_test
KVM: x86/pmu: Update AMD PMC sample period to fix guest NMI-watchdog
x86/kvm: Preserve BSP MSR_KVM_POLL_CONTROL across suspend/resume
KVM: SPDX style and spelling fixes
KVM: x86: Skip KVM_GUESTDBG_BLOCKIRQ APICv update if APICv is disabled
KVM: x86: Pend KVM_REQ_APICV_UPDATE during vCPU creation to fix a race
KVM: nVMX: Defer APICv updates while L2 is active until L1 is active
KVM: x86: Tag APICv DISABLE inhibit, not ABSENT, if APICv is disabled
KVM: Initialize debugfs_dentry when a VM is created to avoid NULL deref
KVM: Add helpers to wrap vcpu->srcu_idx and yell if it's abused
KVM: RISC-V: Use kvm_vcpu.srcu_idx, drop RISC-V's unnecessary copy
KVM: x86: Don't re-acquire SRCU lock in complete_emulated_io()
RISC-V: KVM: Restrict the extensions that can be disabled
RISC-V: KVM: Remove 's' & 'u' as valid ISA extension
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes Palmer Dabbelt:
- A pair of build fixes for the recent cpuidle driver
- A fix for systems without sv57 that manifests as a crash
early in boot
* tag 'riscv-for-linus-5.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
RISC-V: cpuidle: fix Kconfig select for RISCV_SBI_CPUIDLE
RISC-V: mm: Fix set_satp_mode() for platform not having Sv57
cpuidle: riscv: support non-SMP config
|
|
These patch_text implementations are using stop_machine_cpuslocked
infrastructure with atomic cpu_count. The original idea: When the
master CPU patch_text, the others should wait for it. But current
implementation is using the first CPU as master, which couldn't
guarantee the remaining CPUs are waiting. This patch changes the
last CPU as the master to solve the potential risk.
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Signed-off-by: Guo Ren <guoren@kernel.org>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Fixes: 043cb41a85de ("riscv: introduce interfaces to patch kernel code")
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
There can be lots of build errors when building cpuidle-riscv-sbi.o.
They are all caused by a kconfig problem with this warning:
WARNING: unmet direct dependencies detected for RISCV_SBI_CPUIDLE
Depends on [n]: CPU_IDLE [=y] && RISCV [=y] && RISCV_SBI [=n]
Selected by [y]:
- SOC_VIRT [=y] && CPU_IDLE [=y]
so make the 'select' of RISCV_SBI_CPUIDLE also depend on RISCV_SBI.
Fixes: c5179ef1ca0c ("RISC-V: Enable RISC-V SBI CPU Idle driver for QEMU virt machine")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
When Sv57 is not available the satp.MODE test in set_satp_mode() will
fail and lead to pgdir re-programming for Sv48. The pgdir re-programming
will fail as well due to pre-existing pgdir entry used for Sv57 and as
a result kernel fails to boot on RISC-V platform not having Sv57.
To fix above issue, we should clear the pgdir memory in set_satp_mode()
before re-programming.
Fixes: 011f09d12052 ("riscv: mm: Set sv57 on defaultly")
Reported-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
Add wrappers to acquire/release KVM's SRCU lock when stashing the index
in vcpu->src_idx, along with rudimentary detection of illegal usage,
e.g. re-acquiring SRCU and thus overwriting vcpu->src_idx. Because the
SRCU index is (currently) either 0 or 1, illegal nesting bugs can go
unnoticed for quite some time and only cause problems when the nested
lock happens to get a different index.
Wrap the WARNs in PROVE_RCU=y, and make them ONCE, otherwise KVM will
likely yell so loudly that it will bring the kernel to its knees.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Tested-by: Fabiano Rosas <farosas@linux.ibm.com>
Message-Id: <20220415004343.2203171-4-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Use the generic kvm_vcpu's srcu_idx instead of using an indentical field
in RISC-V's version of kvm_vcpu_arch. Generic KVM very intentionally
does not touch vcpu->srcu_idx, i.e. there's zero chance of running afoul
of common code.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220415004343.2203171-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Currently, the config isa register allows us to disable all allowed
single letter ISA extensions. It shouldn't be the case as vmm shouldn't
be able to disable base extensions (imac).
These extensions should always be enabled as long as they are enabled
in the host ISA.
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Fixes: 92ad82002c39 ("RISC-V: KVM: Implement
KVM_GET_ONE_REG/KVM_SET_ONE_REG ioctls")
|
|
There are no ISA extension defined as 's' & 'u' in RISC-V specifications.
The misa register defines 's' & 'u' bit as Supervisor/User privilege mode
enabled. But it should not appear in the ISA extension in the device tree.
Remove those from the allowed ISA extension for kvm.
Fixes: a33c72faf2d7 ("RISC-V: KVM: Implement VCPU create, init and
destroy functions")
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
|
|
vcpu_fp uses the riscv_isa_extension mechanism which gets
defined in hwcap.h but doesn't include that head file.
While it seems to work in most cases, in certain conditions
this can lead to build failures like
../arch/riscv/kvm/vcpu_fp.c: In function ‘kvm_riscv_vcpu_fp_reset’:
../arch/riscv/kvm/vcpu_fp.c:22:13: error: implicit declaration of function ‘riscv_isa_extension_available’ [-Werror=implicit-function-declaration]
22 | if (riscv_isa_extension_available(&isa, f) ||
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../arch/riscv/kvm/vcpu_fp.c:22:49: error: ‘f’ undeclared (first use in this function)
22 | if (riscv_isa_extension_available(&isa, f) ||
Fix this by simply including the necessary header.
Fixes: 0a86512dc113 ("RISC-V: KVM: Factor-out FP virtualization into separate
sources")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Anup Patel <anup@brainfault.org>
|
|
We might have RISC-V systems (such as QEMU) where VMID is not part
of the TLB entry tag so these systems will have to flush all TLB
entries upon any change in hgatp.VMID.
Currently, we zero-out hgatp CSR in kvm_arch_vcpu_put() and we
re-program hgatp CSR in kvm_arch_vcpu_load(). For above described
systems, this will flush all TLB entries whenever VCPU exits to
user-space hence reducing performance.
This patch fixes above described performance issue by not clearing
hgatp CSR in kvm_arch_vcpu_put().
Fixes: 34bde9d8b9e6 ("RISC-V: KVM: Implement VCPU world-switch")
Cc: stable@vger.kernel.org
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull more RISC-V updates from Palmer Dabbelt:
"This has a handful of new features:
- Support for CURRENT_STACK_POINTER, which enables some extra stack
debugging for HARDENED_USERCOPY.
- Support for the new SBI CPU idle extension, via cpuidle and suspend
drivers.
- Profiling has been enabled in the defconfigs.
but is mostly fixes and cleanups"
* tag 'riscv-for-linus-5.18-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (21 commits)
RISC-V: K210 defconfigs: Drop redundant MEMBARRIER=n
RISC-V: defconfig: Drop redundant SBI HVC and earlycon
Documentation: riscv: remove non-existent directory from table of contents
riscv: cpu.c: don't use kernel-doc markers for comments
RISC-V: Enable profiling by default
RISC-V: module: fix apply_r_riscv_rcv_branch_rela typo
RISC-V: Declare per cpu boot data as static
RISC-V: Fix a comment typo in riscv_of_parent_hartid()
riscv: Increase stack size under KASAN
riscv: Fix fill_callchain return value
riscv: dts: canaan: Fix SPI3 bus width
riscv: Rename "sp_in_global" to "current_stack_pointer"
riscv module: remove (NOLOAD)
RISC-V: Enable RISC-V SBI CPU Idle driver for QEMU virt machine
dt-bindings: Add common bindings for ARM and RISC-V idle states
cpuidle: Add RISC-V SBI CPU idle driver
cpuidle: Factor-out power domain related code from PSCI domain driver
RISC-V: Add SBI HSM suspend related defines
RISC-V: Add arch functions for non-retentive suspend entry/exit
RISC-V: Rename relocate() and make it global
...
|
|
As of 93917ad50972 ("RISC-V: Add support for restartable sequence") we
have support for restartable sequences, which default to enabled. These
select MEMBARRIER, so disabling it is now redundant.
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
As of 3938d5a2f936 ("riscv: default to CONFIG_RISCV_SBI_V01=n") we no
longer default to enabling SBI-0.1 support, so these dependent configs
no longer have any effect. Remove them to avoid clutter.
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
Repair kernel-doc build warnings caused by using "/**" kernel-doc
markers for comments that are not in kernel-doc format:
cpu.c:89: warning: cannot understand function prototype: 'struct riscv_isa_ext_data isa_ext_arr[] = '
cpu.c:114: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
Let us enable profiling by default in RV32 and RV64 defconfigs so
that we can use RISC-V PMU drivers on various RISC-V platforms.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
This function name was spelled incorrectly, likely to do a typo.
Signed-off-by: Wu Caize <zepan@sipeed.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
The per cpu boot data is only used within the cpu_ops_sbi.c. It can
be delcared as static.
Fixes: 9a2451f18663 ("RISC-V: Avoid using per cpu array for ordered booting")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
This fixes a typo in a comment that is both obvious and went unnoticed.
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Fixes: a9b202606c69 ("RISC-V: Improve /proc/cpuinfo output for ISA extensions")
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
KASAN requires more stack space because of compiler instrumentation.
Increase stack size as other arches do.
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
Reported-by: syzbot+0600986d88e2d4d7ebb8@syzkaller.appspotmail.com
Fixes: 8ad8b72721d0 ("riscv: Add KASAN support")
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
perf_callchain_store return 0 on success, -1 otherwise,
fix fill_callchain to return correct bool value.
Fixes: dbeb90b0c1eb ("riscv: Add perf callchain support")
Signed-off-by: Nikita Shubin <n.shubin@yadro.com>
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
According to the K210 Standalone SDK Programming guide:
https://canaan-creative.com/wp-content/uploads/2020/03/kendryte_standalone_programming_guide_20190311144158_en.pdf
Section 15.4.3.3:
SPI0 and SPI1 supports: standard, dual, quad and octal transfers.
SPI3 supports: standard, dual and quad transfers (octal is not supported).
In order to support quad transfers (Quad SPI), SPI3 must have four IO wires
connected to the SPI flash.
Update the device tree to specify the correct bus width.
Tested on maix bit, maix dock and maixduino, which all have the same
SPI flash (gd25lq128d) connected to SPI3. maix go is untested, but it
would not make sense for this k210 board to be designed differently.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Fixes: 8f5b0e79f3e5 ("riscv: Add SiPeed MAIXDUINO board device tree")
Fixes: 8194f08bda18 ("riscv: Add SiPeed MAIX GO board device tree")
Fixes: a40f920964c4 ("riscv: Add SiPeed MAIX DOCK board device tree")
Fixes: 97c279bcf813 ("riscv: Add SiPeed MAIX BiT board device tree")
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
This series adds RISC-V CPU Idle support using SBI HSM suspend function.
The RISC-V SBI CPU idle driver added by this series is highly inspired
from the ARM PSCI CPU idle driver.
Special thanks Sandeep Tripathy for providing early feeback on SBI HSM
support in all above projects (RISC-V SBI specification, OpenSBI, and
Linux RISC-V).
* palmer/riscv-idle:
RISC-V: Enable RISC-V SBI CPU Idle driver for QEMU virt machine
dt-bindings: Add common bindings for ARM and RISC-V idle states
cpuidle: Add RISC-V SBI CPU idle driver
cpuidle: Factor-out power domain related code from PSCI domain driver
RISC-V: Add SBI HSM suspend related defines
RISC-V: Add arch functions for non-retentive suspend entry/exit
RISC-V: Rename relocate() and make it global
RISC-V: Enable CPU_IDLE drivers
|
|
To follow the existing per-arch conventions, rename "sp_in_global" to
"current_stack_pointer". This will let it be used in non-arch places
(like HARDENED_USERCOPY).
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"There's one large change in the core clk framework here. We change how
clk_set_rate_range() works so that the frequency is re-evaulated each
time the rate is changed. Previously we wouldn't let clk providers see
a rate that was different if it was still within the range, which
could be bad for power if the clk could run slower when a range
expands. Now the clk provider can decide to do something differently
when the constraints change. This broke Nvidia's clk driver so we had
to wait for the fix for that to bake a little more in -next.
The rate range patch series also introduced a kunit suite for the clk
framework that we're going to extend in the next release. It already
made it easy to find corner cases in the rate range patches so I'm
excited to see it cover more clk code and increase our confidence in
core framework patches in the future. I also added a kunit test for
the basic clk gate code and that work will continue to cover more
basic clk types: muxes, dividers, etc.
Beyond the core code we have the usual set of clk driver updates and
additions. Qualcomm again dominates the diffstat here with lots more
SoCs being supported and i.MX follows afer that with a similar number
of SoCs gaining clk drivers. Beyond those large additions there's
drivers being modernized to use clk_parent_data so we can move away
from global string names for all the clks in an SoC. Finally there's
lots of little fixes all over the clk drivers for typos, warnings, and
missing clks that aren't critical and get batched up waiting for the
next merge window to open. Nothing super big stands out in the driver
pile. Full details are below.
Core:
- Make clk_set_rate_range() re-evaluate the limits each time
- Introduce various clk_set_rate_range() tests
- Add clk_drop_range() to drop a previously set range
New Drivers:
- i.MXRT1050 clock driver and bindings
- i.MX8DXL clock driver and bindings
- i.MX93 clock driver and bindings
- NCO blocks on Apple SoCs
- Audio clks on StarFive JH7100 RISC-V SoC
- Add support for the new Renesas RZ/V2L SoC
- Qualcomm SDX65 A7 PLL
- Qualcomm SM6350 GPU clks
- Qualcomm SM6125, SM6350, QCS2290 display clks
- Qualcomm MSM8226 multimedia clks
Updates:
- Kunit tests for clk-gate implementation
- Terminate arrays with sentinels and make that clearer
- Cleanup SPDX tags
- Fix typos in comments
- Mark mux table as const in clk-mux
- Make the all_lists array const
- Convert Cirrus Logic CS2000P driver to regmap, yamlify DT binding
and add support for dynamic mode
- Clock configuration on Microchip PolarFire SoCs
- Free allocations on probe error in Mediatek clk driver
- Modernize Mediatek clk driver by consolidating code
- Add watchdog (WDT), I2C, and pin function controller (PFC) clocks
on Renesas R-Car S4-8
- Improve the clocks for the Rockchip rk3568 display outputs
(parenting, pll-rates)
- Use of_device_get_match_data() instead of open-coding on Rockchip
rk3568
- Reintroduce the expected fractional-divider behaviour that
disappeared with the addition of CLK_FRAC_DIVIDER_POWER_OF_TWO_PS
- Remove SYS PLL 1/2 clock gates for i.MX8M*
- Remove AUDIO MCLK ROOT from i.MX7D
- Add fracn gppll clock type used by i.MX93
- Add new composite clock for i.MX93
- Add missing media mipi phy ref clock for i.MX8MP
- Fix off by one in imx_lpcg_parse_clks_from_dt()
- Rework for the imx pll14xx
- sama7g5: One low priority fix for GCLK of PDMC
- Add DMA engine (SYS-DMAC) clocks on Renesas R-Car S4-8
- Add MOST (MediaLB I/F) clocks on Renesas R-Car E3 and D3
- Add CAN-FD clocks on Renesas R-Car V3U
- Qualcomm SC8280XP RPMCC
- Add some missing clks on Qualcomm MSM8992/MSM8994/MSM8998 SoCs
- Rework Qualcomm GCC bindings and convert SDM845 camera bindig to
YAML
- Convert various Qualcomm drivers to use clk_parent_data
- Remove test clocks from various Qualcomm drivers
- Crypto engine clks on Qualcomm IPQ806x + more freqs for SDCC/NSS
- Qualcomm SM8150 EMAC, PCIe, UFS GDSCs
- Better pixel clk frequency support on Qualcomm RCG2 clks"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (227 commits)
clk: zynq: Update the parameters to zynq_clk_register_periph_clk
clk: zynq: trivial warning fix
clk: Drop the rate range on clk_put()
clk: test: Test clk_set_rate_range on orphan mux
clk: Initialize orphan req_rate
dt-bindings: clock: drop useless consumer example
dt-bindings: clock: renesas: Make example 'clocks' parsable
clk: qcom: gcc-msm8994: Fix gpll4 width
dt-bindings: clock: fix dt_binding_check error for qcom,gcc-other.yaml
clk: rs9: Add Renesas 9-series PCIe clock generator driver
clk: fixed-factor: Introduce devm_clk_hw_register_fixed_factor_index()
clk: visconti: prevent array overflow in visconti_clk_register_gates()
dt-bindings: clk: rs9: Add Renesas 9-series I2C PCIe clock generator
clk: sifive: Move all stuff into SoCs header files from C files
clk: sifive: Add SoCs prefix in each SoCs-dependent data
riscv: dts: Change the macro name of prci in each device node
dt-bindings: change the macro name of prci in header files and example
clk: sifive: duplicate the macro definitions for the time being
clk: qcom: sm6125-gcc: fix typos in comments
clk: ti: clkctrl: fix typos in comments
...
|
|
On ELF, (NOLOAD) sets the section type to SHT_NOBITS[1]. It is conceptually
inappropriate for .plt, .got, and .got.plt sections which are always
SHT_PROGBITS.
In GNU ld, if PLT entries are needed, .plt will be SHT_PROGBITS anyway
and (NOLOAD) will be essentially ignored. In ld.lld, since
https://reviews.llvm.org/D118840 ("[ELF] Support (TYPE=<value>) to
customize the output section type"), ld.lld will report a `section type
mismatch` error (later changed to a warning). Just remove (NOLOAD) to
fix the warning.
[1] https://lld.llvm.org/ELF/linker_script.html As of today, "The
section should be marked as not loadable" on
https://sourceware.org/binutils/docs/ld/Output-Section-Type.html is
outdated for ELF.
Link: https://github.com/ClangBuiltLinux/linux/issues/1597
Fixes: ab1ef68e5401 ("RISC-V: Add sections of PLT and GOT for kernel module")
Reported-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Fangrui Song <maskray@google.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
* clk-sifive:
clk: sifive: Move all stuff into SoCs header files from C files
clk: sifive: Add SoCs prefix in each SoCs-dependent data
riscv: dts: Change the macro name of prci in each device node
dt-bindings: change the macro name of prci in header files and example
clk: sifive: duplicate the macro definitions for the time being
* clk-visconti:
clk: visconti: prevent array overflow in visconti_clk_register_gates()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull ptrace cleanups from Eric Biederman:
"This set of changes removes tracehook.h, moves modification of all of
the ptrace fields inside of siglock to remove races, adds a missing
permission check to ptrace.c
The removal of tracehook.h is quite significant as it has been a major
source of confusion in recent years. Much of that confusion was around
task_work and TIF_NOTIFY_SIGNAL (which I have now decoupled making the
semantics clearer).
For people who don't know tracehook.h is a vestiage of an attempt to
implement uprobes like functionality that was never fully merged, and
was later superseeded by uprobes when uprobes was merged. For many
years now we have been removing what tracehook functionaly a little
bit at a time. To the point where anything left in tracehook.h was
some weird strange thing that was difficult to understand"
* tag 'ptrace-cleanups-for-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
ptrace: Remove duplicated include in ptrace.c
ptrace: Check PTRACE_O_SUSPEND_SECCOMP permission on PTRACE_SEIZE
ptrace: Return the signal to continue with from ptrace_stop
ptrace: Move setting/clearing ptrace_message into ptrace_stop
tracehook: Remove tracehook.h
resume_user_mode: Move to resume_user_mode.h
resume_user_mode: Remove #ifdef TIF_NOTIFY_RESUME in set_notify_resume
signal: Move set_notify_signal and clear_notify_signal into sched/signal.h
task_work: Decouple TIF_NOTIFY_SIGNAL and task_work
task_work: Call tracehook_notify_signal from get_signal on all architectures
task_work: Introduce task_work_pending
task_work: Remove unnecessary include from posix_timers.h
ptrace: Remove tracehook_signal_handler
ptrace: Remove arch_syscall_{enter,exit}_tracehook
ptrace: Create ptrace_report_syscall_{entry,exit} in ptrace.h
ptrace/arm: Rename tracehook_report_syscall report_syscall
ptrace: Move ptrace_report_syscall into ptrace.h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver updates from Greg KH:
"Here is the big set of char/misc and other small driver subsystem
updates for 5.18-rc1.
Included in here are merges from driver subsystems which contain:
- iio driver updates and new drivers
- fsi driver updates
- fpga driver updates
- habanalabs driver updates and support for new hardware
- soundwire driver updates and new drivers
- phy driver updates and new drivers
- coresight driver updates
- icc driver updates
Individual changes include:
- mei driver updates
- interconnect driver updates
- new PECI driver subsystem added
- vmci driver updates
- lots of tiny misc/char driver updates
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (556 commits)
firmware: google: Properly state IOMEM dependency
kgdbts: fix return value of __setup handler
firmware: sysfb: fix platform-device leak in error path
firmware: stratix10-svc: add missing callback parameter on RSU
arm64: dts: qcom: add non-secure domain property to fastrpc nodes
misc: fastrpc: Add dma handle implementation
misc: fastrpc: Add fdlist implementation
misc: fastrpc: Add helper function to get list and page
misc: fastrpc: Add support to secure memory map
dt-bindings: misc: add fastrpc domain vmid property
misc: fastrpc: check before loading process to the DSP
misc: fastrpc: add secure domain support
dt-bindings: misc: add property to support non-secure DSP
misc: fastrpc: Add support to get DSP capabilities
misc: fastrpc: add support for FASTRPC_IOCTL_MEM_MAP/UNMAP
misc: fastrpc: separate fastrpc device from channel context
dt-bindings: nvmem: brcm,nvram: add basic NVMEM cells
dt-bindings: nvmem: make "reg" property optional
nvmem: brcm_nvram: parse NVRAM content into NVMEM cells
nvmem: dt-bindings: Fix the error of dt-bindings check
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Palmer Dabbelt:
- Support for Sv57-based virtual memory.
- Various improvements for the MicroChip PolarFire SOC and the
associated Icicle dev board, which should allow upstream kernels to
boot without any additional modifications.
- An improved memmove() implementation.
- Support for the new Ssconfpmf and SBI PMU extensions, which allows
for a much more useful perf implementation on RISC-V systems.
- Support for restartable sequences.
* tag 'riscv-for-linus-5.18-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (36 commits)
rseq/selftests: Add support for RISC-V
RISC-V: Add support for restartable sequence
MAINTAINERS: Add entry for RISC-V PMU drivers
Documentation: riscv: Remove the old documentation
RISC-V: Add sscofpmf extension support
RISC-V: Add perf platform driver based on SBI PMU extension
RISC-V: Add RISC-V SBI PMU extension definitions
RISC-V: Add a simple platform driver for RISC-V legacy perf
RISC-V: Add a perf core library for pmu drivers
RISC-V: Add CSR encodings for all HPMCOUNTERS
RISC-V: Remove the current perf implementation
RISC-V: Improve /proc/cpuinfo output for ISA extensions
RISC-V: Do no continue isa string parsing without correct XLEN
RISC-V: Implement multi-letter ISA extension probing framework
RISC-V: Extract multi-letter extension names from "riscv, isa"
RISC-V: Minimal parser for "riscv, isa" strings
RISC-V: Correctly print supported extensions
riscv: Fixed misaligned memory access. Fixed pointer comparison.
MAINTAINERS: update riscv/microchip entry
riscv: dts: microchip: add new peripherals to icicle kit device tree
...
|
|
Merge more updates from Andrew Morton:
"Various misc subsystems, before getting into the post-linux-next
material.
41 patches.
Subsystems affected by this patch series: procfs, misc, core-kernel,
lib, checkpatch, init, pipe, minix, fat, cgroups, kexec, kdump,
taskstats, panic, kcov, resource, and ubsan"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (41 commits)
Revert "ubsan, kcsan: Don't combine sanitizer with kcov on clang"
kernel/resource: fix kfree() of bootmem memory again
kcov: properly handle subsequent mmap calls
kcov: split ioctl handling into locked and unlocked parts
panic: move panic_print before kmsg dumpers
panic: add option to dump all CPUs backtraces in panic_print
docs: sysctl/kernel: add missing bit to panic_print
taskstats: remove unneeded dead assignment
kasan: no need to unset panic_on_warn in end_report()
ubsan: no need to unset panic_on_warn in ubsan_epilogue()
panic: unset panic_on_warn inside panic()
docs: kdump: add scp example to write out the dump file
docs: kdump: update description about sysfs file system support
arm64: mm: use IS_ENABLED(CONFIG_KEXEC_CORE) instead of #ifdef
x86/setup: use IS_ENABLED(CONFIG_KEXEC_CORE) instead of #ifdef
riscv: mm: init: use IS_ENABLED(CONFIG_KEXEC_CORE) instead of #ifdef
kexec: make crashk_res, crashk_low_res and crash_notes symbols always visible
cgroup: use irqsave in cgroup_rstat_flush_locked().
fat: use pointer to simple type in put_user()
minix: fix bug when opening a file with O_DIRECT
...
|
|
Pull kvm updates from Paolo Bonzini:
"ARM:
- Proper emulation of the OSLock feature of the debug architecture
- Scalibility improvements for the MMU lock when dirty logging is on
- New VMID allocator, which will eventually help with SVA in VMs
- Better support for PMUs in heterogenous systems
- PSCI 1.1 support, enabling support for SYSTEM_RESET2
- Implement CONFIG_DEBUG_LIST at EL2
- Make CONFIG_ARM64_ERRATUM_2077057 default y
- Reduce the overhead of VM exit when no interrupt is pending
- Remove traces of 32bit ARM host support from the documentation
- Updated vgic selftests
- Various cleanups, doc updates and spelling fixes
RISC-V:
- Prevent KVM_COMPAT from being selected
- Optimize __kvm_riscv_switch_to() implementation
- RISC-V SBI v0.3 support
s390:
- memop selftest
- fix SCK locking
- adapter interruptions virtualization for secure guests
- add Claudio Imbrenda as maintainer
- first step to do proper storage key checking
x86:
- Continue switching kvm_x86_ops to static_call(); introduce
static_call_cond() and __static_call_ret0 when applicable.
- Cleanup unused arguments in several functions
- Synthesize AMD 0x80000021 leaf
- Fixes and optimization for Hyper-V sparse-bank hypercalls
- Implement Hyper-V's enlightened MSR bitmap for nested SVM
- Remove MMU auditing
- Eager splitting of page tables (new aka "TDP" MMU only) when dirty
page tracking is enabled
- Cleanup the implementation of the guest PGD cache
- Preparation for the implementation of Intel IPI virtualization
- Fix some segment descriptor checks in the emulator
- Allow AMD AVIC support on systems with physical APIC ID above 255
- Better API to disable virtualization quirks
- Fixes and optimizations for the zapping of page tables:
- Zap roots in two passes, avoiding RCU read-side critical
sections that last too long for very large guests backed by 4
KiB SPTEs.
- Zap invalid and defunct roots asynchronously via
concurrency-managed work queue.
- Allowing yielding when zapping TDP MMU roots in response to the
root's last reference being put.
- Batch more TLB flushes with an RCU trick. Whoever frees the
paging structure now holds RCU as a proxy for all vCPUs running
in the guest, i.e. to prolongs the grace period on their behalf.
It then kicks the the vCPUs out of guest mode before doing
rcu_read_unlock().
Generic:
- Introduce __vcalloc and use it for very large allocations that need
memcg accounting"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (246 commits)
KVM: use kvcalloc for array allocations
KVM: x86: Introduce KVM_CAP_DISABLE_QUIRKS2
kvm: x86: Require const tsc for RT
KVM: x86: synthesize CPUID leaf 0x80000021h if useful
KVM: x86: add support for CPUID leaf 0x80000021
KVM: x86: do not use KVM_X86_OP_OPTIONAL_RET0 for get_mt_mask
Revert "KVM: x86/mmu: Zap only TDP MMU leafs in kvm_zap_gfn_range()"
kvm: x86/mmu: Flush TLB before zap_gfn_range releases RCU
KVM: arm64: fix typos in comments
KVM: arm64: Generalise VM features into a set of flags
KVM: s390: selftests: Add error memop tests
KVM: s390: selftests: Add more copy memop tests
KVM: s390: selftests: Add named stages for memop test
KVM: s390: selftests: Add macro as abstraction for MEM_OP
KVM: s390: selftests: Split memop tests
KVM: s390x: fix SCK locking
RISC-V: KVM: Implement SBI HSM suspend call
RISC-V: KVM: Add common kvm_riscv_vcpu_wfi() function
RISC-V: Add SBI HSM suspend related defines
RISC-V: KVM: Implement SBI v0.3 SRST extension
...
|
|
Replace the conditional compilation using "#ifdef CONFIG_KEXEC_CORE" by a
check for "IS_ENABLED(CONFIG_KEXEC_CORE)", to simplify the code and
increase compile coverage.
Link: https://lkml.kernel.org/r/20211206160514.2000-3-jszhang@kernel.org
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Acked-by: Baoquan He <bhe@redhat.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Alexandre Ghiti <alex@ghiti.fr>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"There are three sets of updates for 5.18 in the asm-generic tree:
- The set_fs()/get_fs() infrastructure gets removed for good.
This was already gone from all major architectures, but now we can
finally remove it everywhere, which loses some particularly tricky
and error-prone code. There is a small merge conflict against a
parisc cleanup, the solution is to use their new version.
- The nds32 architecture ends its tenure in the Linux kernel.
The hardware is still used and the code is in reasonable shape, but
the mainline port is not actively maintained any more, as all
remaining users are thought to run vendor kernels that would never
be updated to a future release.
- A series from Masahiro Yamada cleans up some of the uapi header
files to pass the compile-time checks"
* tag 'asm-generic-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (27 commits)
nds32: Remove the architecture
uaccess: remove CONFIG_SET_FS
ia64: remove CONFIG_SET_FS support
sh: remove CONFIG_SET_FS support
sparc64: remove CONFIG_SET_FS support
lib/test_lockup: fix kernel pointer check for separate address spaces
uaccess: generalize access_ok()
uaccess: fix type mismatch warnings from access_ok()
arm64: simplify access_ok()
m68k: fix access_ok for coldfire
MIPS: use simpler access_ok()
MIPS: Handle address errors for accesses above CPU max virtual user address
uaccess: add generic __{get,put}_kernel_nofault
nios2: drop access_ok() check from __put_user()
x86: use more conventional access_ok() definition
x86: remove __range_not_ok()
sparc64: add __{get,put}_kernel_nofault()
nds32: fix access_ok() checks in get/put_user
uaccess: fix nios2 and microblaze get_user_8()
sparc64: fix building assembly files
...
|
|
Add support for RSEQ, restartable sequences, for RISC-V. This also adds
support for the related selftests.
Note: the selftests require a linker with 3e7bd7f2414 ("RISC-V: Fix
linker problems with tls copy relocs."), which was first released in
2.33 (from 2019).
* palmer/riscv-rseq:
rseq/selftests: Add support for RISC-V
RISC-V: Add support for restartable sequence
|
|
node_dev_init()
... and call node_dev_init() after memory_dev_init() from driver_init(),
so before any of the existing arch/subsys calls. All online nodes should
be known at that point: early during boot, arch code determines node and
zone ranges and sets the relevant nodes online; usually this happens in
setup_arch().
This is in line with memory_dev_init(), which initializes the memory
device subsystem and creates all memory block devices.
Similar to memory_dev_init(), panic() if anything goes wrong, we don't
want to continue with such basic initialization errors.
The important part is that node_dev_init() gets called after
memory_dev_init() and after cpu_dev_init(), but before any of the relevant
archs call register_cpu() to register the new cpu device under the node
device. The latter should be the case for the current users of
topology_init().
Link: https://lkml.kernel.org/r/20220203105212.30385-1-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Tested-by: Anatoly Pugachev <matorola@gmail.com> (sparc64)
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
ARCH_WANT_GENERAL_HUGETLB config has duplicate definitions on platforms
that subscribe it. Instead make it a generic config option which can be
selected on applicable platforms when required.
Link: https://lkml.kernel.org/r/1643718465-4324-1-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
