| Age | Commit message (Collapse) | Author |
|---|
|
When the platform detects an error on a PCI function or a service action
has been performed it is put in the error state and an error event
notification is provided to the OS.
Currently we treat all error event notifications the same and simply set
pdev->error_state = pci_channel_io_perm_failure requiring user
intervention such as use of the recover attribute to get the device
usable again. Despite requiring a manual step this also has the
disadvantage that the device is completely torn down and recreated
resulting in higher level devices such as a block or network device
being recreated. In case of a block device this also means that it may
need to be removed and added to a software raid even if that could
otherwise survive with a temporary degradation.
This is of course not ideal more so since an error notification with PEC
0x3A indicates that the platform already performed error recovery
successfully or that the error state was caused by a service action that
is now finished.
At least in this case we can assume that the error state can be reset
and the function made usable again. So as not to have the disadvantage
of a full tear down and recreation we need to coordinate this recovery
with the driver. Thankfully there is already a well defined recovery
flow for this described in Documentation/PCI/pci-error-recovery.rst.
The implementation of this is somewhat straight forward and simplified
by the fact that our recovery flow is defined per PCI function. As
a reset we use the newly introduced zpci_hot_reset_device() which also
takes the PCI function out of the error state.
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Acked-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
This is done by adding a zpci_hot_reset_device() call which does a low
level reset of the PCI function without changing its higher level
function state. This way it can be used while the zPCI function is bound
to a driver and with DMA tables being controlled either through the
IOMMU or DMA APIs which is prohibited when using zpci_disable_device()
as that drop existing DMA translations.
As this reset, unlike a normal FLR, also calls zpci_clear_irq() we need
to implement arch_restore_msi_irqs() and make sure we re-enable IRQs for
the PCI function if they were previously disabled.
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
The function handle of a PCI function is updated when disabling or
enabling it as well as when the function's availability changes or it
enters the error state.
Until now this only occurred either while there is no struct pci_dev
associated with the function yet or the function became unavailable.
This meant that leaving a stale function handle in the iomap either
didn't happen because there was no iomap yet or it lead to errors on PCI
access but so would the correct disabled function handle.
In the future a CLP Set PCI Function Disable/Enable cycle during PCI
device recovery may be done while the device is bound to a driver. In
this case we must update the iomap associated with the now-stale
function handle to ensure that the resulting zPCI instruction references
an accurate function handle.
Since the function handle is accessed by the PCI accessor helpers
without locking use READ_ONCE()/WRITE_ONCE() to mark this access and
prevent compiler optimizations that would move the load/store.
With that infrastructure in place let's also properly update the
function handle in the existing cases. This makes sure that in the
future debugging of a zPCI function access through the handle will
show an up to date handle reducing the chance of confusion. Also it
makes sure we have one single place where a zPCI function handle is
updated after initialization.
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Vasily Gorbik:
- Add support for ftrace with direct call and ftrace direct call
samples.
- Add support for kernel command lines longer than current 896 bytes
and make its length configurable.
- Add support for BEAR enhancement facility to improve last breaking
event instruction tracking.
- Add kprobes sanity checks and testcases to prevent kprobe in the mid
of an instruction.
- Allow concurrent access to /dev/hwc for the CPUMF users.
- Various ftrace / jump label improvements.
- Convert unwinder tests to KUnit.
- Add s390_iommu_aperture kernel parameter to tweak the limits on
concurrently usable DMA mappings.
- Add ap.useirq AP module option which can be used to disable interrupt
use.
- Add add_disk() error handling support to block device drivers.
- Drop arch specific and use generic implementation of strlcpy and
strrchr.
- Several __pa/__va usages fixes.
- Various cio, crypto, pci, kernel doc and other small fixes and
improvements all over the code.
[ Merge fixup as per https://lore.kernel.org/all/YXAqZ%2FEszRisunQw@osiris/ ]
* tag 's390-5.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (63 commits)
s390: make command line configurable
s390: support command lines longer than 896 bytes
s390/kexec_file: move kernel image size check
s390/pci: add s390_iommu_aperture kernel parameter
s390/spinlock: remove incorrect kernel doc indicator
s390/string: use generic strlcpy
s390/string: use generic strrchr
s390/ap: function rework based on compiler warning
s390/cio: make ccw_device_dma_* more robust
s390/vfio-ap: s390/crypto: fix all kernel-doc warnings
s390/hmcdrv: fix kernel doc comments
s390/ap: new module option ap.useirq
s390/cpumf: Allow multiple processes to access /dev/hwc
s390/bitops: return true/false (not 1/0) from bool functions
s390: add support for BEAR enhancement facility
s390: introduce nospec_uses_trampoline()
s390: rename last_break to pgm_last_break
s390/ptrace: add last_break member to pt_regs
s390/sclp: sort out physical vs virtual pointers usage
s390/setup: convert start and end initrd pointers to virtual
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Conserve IRQs by setting up portdrv IRQs only when there are users
(Jan Kiszka)
- Rework and simplify _OSC negotiation for control of PCIe features
(Joerg Roedel)
- Remove struct pci_dev.driver pointer since it's redundant with the
struct device.driver pointer (Uwe Kleine-König)
Resource management:
- Coalesce contiguous host bridge apertures from _CRS to accommodate
BARs that cover more than one aperture (Kai-Heng Feng)
Sysfs:
- Check CAP_SYS_ADMIN before parsing user input (Krzysztof
Wilczyński)
- Return -EINVAL consistently from "store" functions (Krzysztof
Wilczyński)
- Use sysfs_emit() in endpoint "show" functions to avoid buffer
overruns (Kunihiko Hayashi)
PCIe native device hotplug:
- Ignore Link Down/Up caused by resets during error recovery so
endpoint drivers can remain bound to the device (Lukas Wunner)
Virtualization:
- Avoid bus resets on Atheros QCA6174, where they hang the device
(Ingmar Klein)
- Work around Pericom PI7C9X2G switch packet drop erratum by using
store and forward mode instead of cut-through (Nathan Rossi)
- Avoid trying to enable AtomicOps on VFs; the PF setting applies to
all VFs (Selvin Xavier)
MSI:
- Document that /sys/bus/pci/devices/.../irq contains the legacy INTx
interrupt or the IRQ of the first MSI (not MSI-X) vector (Barry
Song)
VPD:
- Add pci_read_vpd_any() and pci_write_vpd_any() to access anywhere
in the possible VPD space; use these to simplify the cxgb3 driver
(Heiner Kallweit)
Peer-to-peer DMA:
- Add (not subtract) the bus offset when calculating DMA address
(Wang Lu)
ASPM:
- Re-enable LTR at Downstream Ports so they don't report Unsupported
Requests when reset or hot-added devices send LTR messages
(Mingchuang Qiao)
Apple PCIe controller driver:
- Add driver for Apple M1 PCIe controller (Alyssa Rosenzweig, Marc
Zyngier)
Cadence PCIe controller driver:
- Return success when probe succeeds instead of falling into error
path (Li Chen)
HiSilicon Kirin PCIe controller driver:
- Reorganize PHY logic and add support for external PHY drivers
(Mauro Carvalho Chehab)
- Support PERST# GPIOs for HiKey970 external PEX 8606 bridge (Mauro
Carvalho Chehab)
- Add Kirin 970 support (Mauro Carvalho Chehab)
- Make driver removable (Mauro Carvalho Chehab)
Intel VMD host bridge driver:
- If IOMMU supports interrupt remapping, leave VMD MSI-X remapping
enabled (Adrian Huang)
- Number each controller so we can tell them apart in
/proc/interrupts (Chunguang Xu)
- Avoid building on UML because VMD depends on x86 bare metal APIs
(Johannes Berg)
Marvell Aardvark PCIe controller driver:
- Define macros for PCI_EXP_DEVCTL_PAYLOAD_* (Pali Rohár)
- Set Max Payload Size to 512 bytes per Marvell spec (Pali Rohár)
- Downgrade PIO Response Status messages to debug level (Marek Behún)
- Preserve CRS SV (Config Request Retry Software Visibility) bit in
emulated Root Control register (Pali Rohár)
- Fix issue in configuring reference clock (Pali Rohár)
- Don't clear status bits for masked interrupts (Pali Rohár)
- Don't mask unused interrupts (Pali Rohár)
- Avoid code repetition in advk_pcie_rd_conf() (Marek Behún)
- Retry config accesses on CRS response (Pali Rohár)
- Simplify emulated Root Capabilities initialization (Pali Rohár)
- Fix several link training issues (Pali Rohár)
- Fix link-up checking via LTSSM (Pali Rohár)
- Fix reporting of Data Link Layer Link Active (Pali Rohár)
- Fix emulation of W1C bits (Marek Behún)
- Fix MSI domain .alloc() method to return zero on success (Marek
Behún)
- Read entire 16-bit MSI vector in MSI handler, not just low 8 bits
(Marek Behún)
- Clear Root Port I/O Space, Memory Space, and Bus Master Enable bits
at startup; PCI core will set those as necessary (Pali Rohár)
- When operating as a Root Port, set class code to "PCI Bridge"
instead of the default "Mass Storage Controller" (Pali Rohár)
- Add emulation for PCI_BRIDGE_CTL_BUS_RESET since aardvark doesn't
implement this per spec (Pali Rohár)
- Add emulation of option ROM BAR since aardvark doesn't implement
this per spec (Pali Rohár)
MediaTek MT7621 PCIe controller driver:
- Add MediaTek MT7621 PCIe host controller driver and DT binding
(Sergio Paracuellos)
Qualcomm PCIe controller driver:
- Add SC8180x compatible string (Bjorn Andersson)
- Add endpoint controller driver and DT binding (Manivannan
Sadhasivam)
- Restructure to use of_device_get_match_data() (Prasad Malisetty)
- Add SC7280-specific pcie_1_pipe_clk_src handling (Prasad Malisetty)
Renesas R-Car PCIe controller driver:
- Remove unnecessary includes (Geert Uytterhoeven)
Rockchip DesignWare PCIe controller driver:
- Add DT binding (Simon Xue)
Socionext UniPhier Pro5 controller driver:
- Serialize INTx masking/unmasking (Kunihiko Hayashi)
Synopsys DesignWare PCIe controller driver:
- Run dwc .host_init() method before registering MSI interrupt
handler so we can deal with pending interrupts left by bootloader
(Bjorn Andersson)
- Clean up Kconfig dependencies (Andy Shevchenko)
- Export symbols to allow more modular drivers (Luca Ceresoli)
TI DRA7xx PCIe controller driver:
- Allow host and endpoint drivers to be modules (Luca Ceresoli)
- Enable external clock if present (Luca Ceresoli)
TI J721E PCIe driver:
- Disable PHY when probe fails after initializing it (Christophe
JAILLET)
MicroSemi Switchtec management driver:
- Return error to application when command execution fails because an
out-of-band reset has cleared the device BARs, Memory Space Enable,
etc (Kelvin Cao)
- Fix MRPC error status handling issue (Kelvin Cao)
- Mask out other bits when reading of management VEP instance ID
(Kelvin Cao)
- Return EOPNOTSUPP instead of ENOTSUPP from sysfs show functions
(Kelvin Cao)
- Add check of event support (Logan Gunthorpe)
Miscellaneous:
- Remove unused pci_pool wrappers, which have been replaced by
dma_pool (Cai Huoqing)
- Use 'unsigned int' instead of bare 'unsigned' (Krzysztof
Wilczyński)
- Use kstrtobool() directly, sans strtobool() wrapper (Krzysztof
Wilczyński)
- Fix some sscanf(), sprintf() format mismatches (Krzysztof
Wilczyński)
- Update PCI subsystem information in MAINTAINERS (Krzysztof
Wilczyński)
- Correct some misspellings (Krzysztof Wilczyński)"
* tag 'pci-v5.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (137 commits)
PCI: Add ACS quirk for Pericom PI7C9X2G switches
PCI: apple: Configure RID to SID mapper on device addition
iommu/dart: Exclude MSI doorbell from PCIe device IOVA range
PCI: apple: Implement MSI support
PCI: apple: Add INTx and per-port interrupt support
PCI: kirin: Allow removing the driver
PCI: kirin: De-init the dwc driver
PCI: kirin: Disable clkreq during poweroff sequence
PCI: kirin: Move the power-off code to a common routine
PCI: kirin: Add power_off support for Kirin 960 PHY
PCI: kirin: Allow building it as a module
PCI: kirin: Add MODULE_* macros
PCI: kirin: Add Kirin 970 compatible
PCI: kirin: Support PERST# GPIOs for HiKey970 external PEX 8606 bridge
PCI: apple: Set up reference clocks when probing
PCI: apple: Add initial hardware bring-up
PCI: of: Allow matching of an interrupt-map local to a PCI device
of/irq: Allow matching of an interrupt-map local to an interrupt controller
irqdomain: Make of_phandle_args_to_fwspec() generally available
PCI: Do not enable AtomicOps on VFs
...
|
|
Some applications map the same memory area for DMA multiple times while
also mapping significant amounts of memory. With our current DMA code
these applications will run out of DMA addresses after mapping half of
the available memory because the number of DMA mappings is constrained
by the number of concurrently active DMA addresses we support which in
turn is limited by the minimum of hardware constraints and high_memory.
Limiting the number of active DMA addresses to high_memory is only
a heuristic to save memory used by the iommu_bitmap and DMA page tables
however. This was added under the assumption that it rarely makes sense
to DMA map more than system memory.
To accommodate special applications which insist on double mapping, which
works on other platforms, allow specifying a factor of how many times
installed memory is available as DMA address space. Use 0 as a special
value to apply no constraints beyond what hardware dictates at the
expense of significantly more memory use.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
pci and string functions changes on features depend on changes from the
fixes branch.
* fixes:
s390: add Alexander Gordeev as reviewer
s390: fix strrchr() implementation
vfio-ccw: step down as maintainer
KVM: s390: remove myself as reviewer
s390/pci: fix zpci_zdev_put() on reserve
bpf, s390: Fix potential memory leak about jit_data
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
We often need to figure out what operations were performed in response
to an error or availability event. The operations are easily accessible
in s390dbf/pci_msg but the events have to be correlated with these from
either the kernel log or s390dbf/pci_err. Improve this situation by
logging the most important data from error and availability events that
is the FID, PEC and FH together with the operations.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Since commit 8256adda1f44 ("s390/pci: handle FH state mismatch only on
disable") zpci_disable_device() returns -EINVAL when the platform
detects an attempt to disable a PCI function that it sees as already
disabled.
In most situations we want to abort whenever this happens and abort is
possible since it either means that the device vanished but we haven't
gotten an availability event yet, or the FH got out of sync which should
not happen.
Unfortunately there is an inconsistency between the LPAR and z/VM
hypervisors on whether error events for PCI functions contain an
an enabled or a general handle. So under z/VM it can happen that our
most up to date function handle is enabled but trying to disable the
function results in the aforementioned error.
Since recover is designed to be used to recover functions from the error
state let's make it robust to this inconsistency by explicitly treating
it as a successful disable.
Acked-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Since commit 2a671f77ee49 ("s390/pci: fix use after free of zpci_dev")
the reference count of a zpci_dev is incremented between
pcibios_add_device() and pcibios_release_device() which was supposed to
prevent the zpci_dev from being freed while the common PCI code has
access to it. It was missed however that the handling of zPCI
availability events assumed that once zpci_zdev_put() was called no
later availability event would still see the device. With the previously
mentioned commit however this assumption no longer holds and we must
make sure that we only drop the initial long-lived reference the zPCI
subsystem holds exactly once.
Do so by introducing a zpci_device_reserved() function that handles when
a device is reserved. Here we make sure the zpci_dev will not be
considered for further events by removing it from the zpci_list.
This also means that the device actually stays in the
ZPCI_FN_STATE_RESERVED state between the time we know it has been
reserved and the final reference going away. We thus need to consider it
a real state instead of just a conceptual state after the removal. The
final cleanup of PCI resources, removal from zbus, and destruction of
the IOMMU stays in zpci_release_device() to make sure holders of the
reference do see valid data until the release.
Fixes: 2a671f77ee49 ("s390/pci: fix use after free of zpci_dev")
Cc: stable@vger.kernel.org
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
The general convention for pcibios_* hooks is that they're named after the
corresponding pci_* function they provide a hook for. The exception is
pcibios_add_device() which provides a hook for pci_device_add().
Rename pcibios_add_device() to pcibios_device_add() so it matches
pci_device_add().
Also, remove the export of the microblaze version. The only caller must be
compiled as a built-in so there's no reason for the export.
Link: https://lore.kernel.org/r/20210913152709.48013-1-oohall@gmail.com
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Niklas Schnelle <schnelle@linux.ibm.com> # s390
|
|
We should not walk/touch page tables outside of VMA boundaries when
holding only the mmap sem in read mode. Evil user space can modify the
VMA layout just before this function runs and e.g., trigger races with
page table removal code since commit dd2283f2605e ("mm: mmap: zap pages
with read mmap_sem in munmap").
find_vma() does not check if the address is >= the VMA start address;
use vma_lookup() instead.
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Fixes: dd2283f2605e ("mm: mmap: zap pages with read mmap_sem in munmap")
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull more s390 updates from Heiko Carstens:
"Except for the xpram device driver removal it is all about fixes and
cleanups.
- Fix topology update on cpu hotplug, so notifiers see expected
masks. This bug was uncovered with SCHED_CORE support.
- Fix stack unwinding so that the correct number of entries are
omitted like expected by common code. This fixes KCSAN selftests.
- Add kmemleak annotation to stack_alloc to avoid false positive
kmemleak warnings.
- Avoid layering violation in common I/O code and don't unregister
subchannel from child-drivers.
- Remove xpram device driver for which no real use case exists since
the kernel is 64 bit only. Also all hypervisors got required
support removed in the meantime, which means the xpram device
driver is dead code.
- Fix -ENODEV handling of clp_get_state in our PCI code.
- Enable KFENCE in debug defconfig.
- Cleanup hugetlbfs s390 specific Kconfig dependency.
- Quite a lot of trivial fixes to get rid of "W=1" warnings, and and
other simple cleanups"
* tag 's390-5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
hugetlbfs: s390 is always 64bit
s390/ftrace: remove incorrect __va usage
s390/zcrypt: remove incorrect kernel doc indicators
scsi: zfcp: fix kernel doc comments
s390/sclp: add __nonstring annotation
s390/hmcdrv_ftp: fix kernel doc comment
s390: remove xpram device driver
s390/pci: read clp_list_pci_req only once
s390/pci: fix clp_get_state() handling of -ENODEV
s390/cio: fix kernel doc comment
s390/ctrlchar: fix kernel doc comment
s390/con3270: use proper type for tasklet function
s390/cpum_cf: move array from header to C file
s390/mm: fix kernel doc comments
s390/topology: fix topology information when calling cpu hotplug notifiers
s390/unwind: use current_frame_address() to unwind current task
s390/configs: enable CONFIG_KFENCE in debug_defconfig
s390/entry: make oklabel within CHKSTG macro local
s390: add kmemleak annotation in stack_alloc()
s390/cio: dont unregister subchannel from child-drivers
|
|
We do not have to reset the fh_list in the loop.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
With commit cc049eecfb7a ("s390/pci: simplify CLP List PCI handling")
clp_get_state() was changed to make use of the new clp_find_pci() helper
function to query a specific function. This however returns -ENODEV when
the device is not found at all and this error was passed to the caller.
It was missed however that the callers actually expect a success return
from clp_get_state() if the device is gone.
Fix this by handling the -ENODEV return of clp_find_pci() explicitly in
clp_get_state() returning success and setting the state parameter to
ZPCI_FN_STATE_RESERVED matching the design concept that a PCI function
that disappeared must have been resverved elsewhere. For all other error
returns continue to just pass them on to the caller.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Fixes: cc049eecfb7a ("s390/pci: simplify CLP List PCI handling")
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Pull dma-mapping updates from Christoph Hellwig:
- fix debugfs initialization order (Anthony Iliopoulos)
- use memory_intersects() directly (Kefeng Wang)
- allow to return specific errors from ->map_sg (Logan Gunthorpe,
Martin Oliveira)
- turn the dma_map_sg return value into an unsigned int (me)
- provide a common global coherent pool іmplementation (me)
* tag 'dma-mapping-5.15' of git://git.infradead.org/users/hch/dma-mapping: (31 commits)
hexagon: use the generic global coherent pool
dma-mapping: make the global coherent pool conditional
dma-mapping: add a dma_init_global_coherent helper
dma-mapping: simplify dma_init_coherent_memory
dma-mapping: allow using the global coherent pool for !ARM
ARM/nommu: use the generic dma-direct code for non-coherent devices
dma-direct: add support for dma_coherent_default_memory
dma-mapping: return an unsigned int from dma_map_sg{,_attrs}
dma-mapping: disallow .map_sg operations from returning zero on error
dma-mapping: return error code from dma_dummy_map_sg()
x86/amd_gart: don't set failed sg dma_address to DMA_MAPPING_ERROR
x86/amd_gart: return error code from gart_map_sg()
xen: swiotlb: return error code from xen_swiotlb_map_sg()
parisc: return error code from .map_sg() ops
sparc/iommu: don't set failed sg dma_address to DMA_MAPPING_ERROR
sparc/iommu: return error codes from .map_sg() ops
s390/pci: don't set failed sg dma_address to DMA_MAPPING_ERROR
s390/pci: return error code from s390_dma_map_sg()
powerpc/iommu: don't set failed sg dma_address to DMA_MAPPING_ERROR
powerpc/iommu: return error code from .map_sg() ops
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"Updates to the interrupt core and driver subsystems:
Core changes:
- The usual set of small fixes and improvements all over the place,
but nothing stands out
MSI changes:
- Further consolidation of the PCI/MSI interrupt chip code
- Make MSI sysfs code independent of PCI/MSI and expose the MSI
interrupts of platform devices in the same way as PCI exposes them.
Driver changes:
- Support for ARM GICv3 EPPI partitions
- Treewide conversion to generic_handle_domain_irq() for all chained
interrupt controllers
- Conversion to bitmap_zalloc() throughout the irq chip drivers
- The usual set of small fixes and improvements"
* tag 'irq-core-2021-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (57 commits)
platform-msi: Add ABI to show msi_irqs of platform devices
genirq/msi: Move MSI sysfs handling from PCI to MSI core
genirq/cpuhotplug: Demote debug printk to KERN_DEBUG
irqchip/qcom-pdc: Trim unused levels of the interrupt hierarchy
irqdomain: Export irq_domain_disconnect_hierarchy()
irqchip/gic-v3: Fix priority comparison when non-secure priorities are used
irqchip/apple-aic: Fix irq_disable from within irq handlers
pinctrl/rockchip: drop the gpio related codes
gpio/rockchip: drop irq_gc_lock/irq_gc_unlock for irq set type
gpio/rockchip: support next version gpio controller
gpio/rockchip: use struct rockchip_gpio_regs for gpio controller
gpio/rockchip: add driver for rockchip gpio
dt-bindings: gpio: change items restriction of clock for rockchip,gpio-bank
pinctrl/rockchip: add pinctrl device to gpio bank struct
pinctrl/rockchip: separate struct rockchip_pin_bank to a head file
pinctrl/rockchip: always enable clock for gpio controller
genirq: Fix kernel doc indentation
EDAC/altera: Convert to generic_handle_domain_irq()
powerpc: Bulk conversion to generic_handle_domain_irq()
nios2: Bulk conversion to generic_handle_domain_irq()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Heiko Carstens:
- Improve ftrace code patching so that stop_machine is not required
anymore. This requires a small common code patch acked by Steven
Rostedt:
https://lore.kernel.org/linux-s390/20210730220741.4da6fdf6@oasis.local.home/
- Enable KCSAN for s390. This comes with a small common code change to
fix a compile warning. Acked by Marco Elver:
https://lore.kernel.org/r/20210729142811.1309391-1-hca@linux.ibm.com
- Add KFENCE support for s390. This also comes with a minimal x86 patch
from Marco Elver who said also this can be carried via the s390 tree:
https://lore.kernel.org/linux-s390/YQJdarx6XSUQ1tFZ@elver.google.com/
- More changes to prepare the decompressor for relocation.
- Enable DAT also for CPU restart path.
- Final set of register asm removal patches; leaving only three
locations where needed and sane.
- Add NNPA, Vector-Packed-Decimal-Enhancement Facility 2, PCI MIO
support to hwcaps flags.
- Cleanup hwcaps implementation.
- Add new instructions to in-kernel disassembler.
- Various QDIO cleanups.
- Add SCLP debug feature.
- Various other cleanups and improvements all over the place.
* tag 's390-5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (105 commits)
s390: remove SCHED_CORE from defconfigs
s390/smp: do not use nodat_stack for secondary CPU start
s390/smp: enable DAT before CPU restart callback is called
s390: update defconfigs
s390/ap: fix state machine hang after failure to enable irq
KVM: s390: generate kvm hypercall functions
s390/sclp: add tracing of SCLP interactions
s390/debug: add early tracing support
s390/debug: fix debug area life cycle
s390/debug: keep debug data on resize
s390/diag: make restart_part2 a local label
s390/mm,pageattr: fix walk_pte_level() early exit
s390: fix typo in linker script
s390: remove do_signal() prototype and do_notify_resume() function
s390/crypto: fix all kernel-doc warnings in vfio_ap_ops.c
s390/pci: improve DMA translation init and exit
s390/pci: simplify CLP List PCI handling
s390/pci: handle FH state mismatch only on disable
s390/pci: fix misleading rc in clp_set_pci_fn()
s390/boot: factor out offset_vmlinux_info() function
...
|
|
Currently zpci_dma_init_device()/zpci_dma_exit_device() is called as
part of zpci_enable_device()/zpci_disable_device() and errors for
zpci_dma_exit_device() are always ignored even if we could abort.
Improve upon this by moving zpci_dma_exit_device() out of
zpci_disable_device() and check for errors whenever we have a way to
abort the current operation. Note that for example in
zpci_event_hard_deconfigured() the device is expected to be gone so we
really can't abort and proceed even in case of error.
Similarly move the cc == 3 special case out of zpci_unregister_ioat()
and into the callers allowing to abort when finding an already disabled
devices precludes proceeding with the operation.
While we are at it log IOAT register/unregister errors in the s390
debugfs log,
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Currently clp_get_state() and clp_refresh_fh() awkwardly use the
clp_list_pci() callback mechanism to find the entry for a specific FID
and update its zdev, respectively return its state.
This is both needlessly complex and means we are always going through
the entire PCI function list even if the FID has already been found.
Instead lets introduce a clp_find_pci() function to find a specific
entry and share the CLP List PCI request handling code with
clp_list_pci().
With that in place we can also easily make the function handle a simple
out parameter instead of directly altering the zdev allowing easier
access to the updated function handle by the caller.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Instead of always treating CLP_RC_SETPCIFN_ALRDY as success and blindly
updating the function handle restrict this special handling to the
disable case by moving it into zpci_disable_device() and still treating
it as an error while also updating the function handle such that
a subsequent zpci_disable_device() succeeds or the caller can ignore the
error when aborting is not an option such as for zPCI event 0x304.
Also print this occurrence to the log such that an admin can tell why
a disable operation returned an error.
A mismatch between the state of the underlying device and our view of it
can naturally happen when the device suddenly enters the error state but
we haven't gotten the error notification yet, it must not happen on
enable though.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Currently clp_set_pci_fn() always returns 0 as long as the CLP request
itself succeeds even if the operation itself returns a response code
other than CLP_RC_OK or CLP_RC_SETPCIFN_ALRDY. This is highly misleading
because calling code assumes that a zero rc means that the operation was
successful.
Fix this by returning the response code or cc on failure with the
exception of the special handling for CLP_RC_SETPCIFN_ALRDY. Also let's
not assume that the returned function handle for CLP_RC_SETPCIFN_ALRDY
is 0, we don't need it anyway.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
On failure to register a struct zpci_dev with a struct zpci_bus we left
a dangling pointer in zdev->zbus. As zpci_create_device() bails if
zpci_bus_device_register() fails this is of no consequence but still bad
practice.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
It's currently safe to call zpci_cleanup_bus_resources() even if the
resources were never created but it makes no sense so check
zdev->has_resources before we call zpci_cleanup_bus_resources() in
zpci_release_device().
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Acked-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
The struct pci_dev uses reference counting but zPCI assumed erroneously
that the last reference would always be the local reference after
calling pci_stop_and_remove_bus_device(). This is usually the case but
not how reference counting works and thus inherently fragile.
In fact one case where this causes a NULL pointer dereference when on an
SRIOV device the function 0 was hot unplugged before another function of
the same multi-function device. In this case the second function's
pdev->sriov->dev reference keeps the struct pci_dev of function 0 alive
even after the unplug. This bug was previously hidden by the fact that
we were leaking the struct pci_dev which in turn means that it always
outlived the struct zpci_dev. This was fixed in commit 0b13525c20fe
("s390/pci: fix leak of PCI device structure") exposing the broken
behavior.
Fix this by accounting for the long living reference a struct pci_dev
has to its underlying struct zpci_dev via the zbus->function[] array and
only release that in pcibios_release_device() ensuring that the struct
pci_dev is not left with a dangling reference. This is a minimal fix in
the future it would probably better to use fine grained reference
counting for struct zpci_dev.
Fixes: 05bc1be6db4b2 ("s390/pci: create zPCI bus")
Cc: stable@vger.kernel.org
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
The PCI core already ensures that the MSI[-X] state is correct when MSI[-X]
is disabled. For MSI the reset state is all entries unmasked and for MSI-X
all vectors are masked.
S390 masks all MSI entries and masks the already masked MSI-X entries
again. Remove it and let the device in the correct state.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Niklas Schnelle <schnelle@linux.ibm.com>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Acked-by: Niklas Schnelle <schnelle@linux.ibm.com>
Link: https://lore.kernel.org/r/20210729222542.939798136@linutronix.de
|
|
Setting the ->dma_address to DMA_MAPPING_ERROR is not part of
the ->map_sg calling convention, so remove it.
Link: https://lore.kernel.org/linux-mips/20210716063241.GC13345@lst.de/
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Cc: Niklas Schnelle <schnelle@linux.ibm.com>
Cc: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The .map_sg() op now expects an error code instead of zero on failure.
So propagate the error from __s390_dma_map_sg() up. __s390_dma_map_sg()
returns either -ENOMEM on allocation failure or -EINVAL which is
the same as what's expected by dma_map_sgtable().
Signed-off-by: Martin Oliveira <martin.oliveira@eideticom.com>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Niklas Schnelle <schnelle@linux.ibm.com>
Cc: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Kernel support for the newer PCI mio instructions can be toggled off
with the pci=nomio command line option which needs to integrate with
common code PCI option parsing. However this option then toggles static
branches which can't be toggled yet in an early_param() call.
Thus commit 9964f396f1d0 ("s390: fix setting of mio addressing control")
moved toggling the static branches to the PCI init routine.
With this setup however we can't check for mio support outside the PCI
code during early boot, i.e. before switching the static branches, which
we need to be able to export this as an ELF HWCAP.
Improve on this by turning mio availability into a machine flag that
gets initially set based on CONFIG_PCI and the facility bit and gets
toggled off if pci=nomio is found during PCI option parsing allowing
simple access to this machine flag after early init.
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Pull the directed vs floating IRQ check into common
zpci_set_irq()/zpci_clear_irq() functions and expose them for the rest
of the zPCI subsystem. Furthermore we add a zdev flag bit to easily
check if IRQs are registered. This is needed for use in resetting a zPCI
function.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
The PCIs event with PEC 0x0303 or 0x0304 are a request to deconfigure
a PCI function, respectively an indication that it was already
deconfigured by the platform. If such an event is queued during boot it
may happen that the platform has already adjusted the configuration flag
of the relevant function in the CLP List PCI Functions result. In this
case we might not have configured the PCI function at all and should
thus ignore the event. Note that no locking is necessary as event
handling only starts after we have fully initialized the zPCI subsystem
and scanned all PCI devices listed in the CLP result.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Acked-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
With zpci_configure_device() now always called on a device that has
already been configured on the platform level its name has become
misleading. Rename it to zpci_scan_configured_device() to signify that
the function now only handles the correct scanning of a newly configured
PCI function taking care of the special handling necessary for function
0 and functions parked waiting for a PCI bus that can't be created
without first seeing function 0.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
On s390 each PCI device has a user-defined ID (UID) exposed under
/sys/bus/pci/devices/<dev>/uid. This ID was designed to serve as the PCI
device's primary index and to match the device within Linux to the
device configured in the hypervisor. To serve as a primary identifier
the UID must be unique within the Linux instance, this is guaranteed by
the platform if and only if the UID Uniqueness Checking flag is set
within the CLP List PCI Functions response.
In this sense the UID serves an analogous function as the SMBIOS
instance number or ACPI index exposed as the "index" respectively
"acpi_index" device attributes and used by e.g. systemd to set interface
names. As s390 does not use and will likely never use ACPI nor SMBIOS
there is no conflict and we can just expose the UID under the "index"
attribute whenever UID Uniqueness Checking is active and get systemd's
interface naming support for free.
Link: https://lore.kernel.org/lkml/20210412135905.1434249-1-schnelle@linux.ibm.com/
Acked-by: Viktor Mihajlovski <mihajlov@linux.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Narendra K <narendra_k@dell.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Currently zpci_configure_device() can be called on a zPCI function in
two completely different states. Either the underlying zPCI function has
already been configured by the platform and we are only doing the
scanning to get it usable by Linux drivers. Or the underlying function
is in Standby and we first do an SCLP to get it configured. This makes
zpci_configure_device() harder to reason about. Since calling
zpci_configure_device() on a function in Standby only happens in
enable_slot() simply pull out the SCLP call and setting of zdev->state
and thus call zpci_configure_device() under the same circumstances as
in the event handling code.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Now that the zbus can be created without being scanned we can go one
step further and make registering a device to a zbus independent from
scanning it. This way the zbus handling becomes much more natural
in that functions can be registered on the zbus to be scanned later more
closely resembling the handling of both real PCI hardware and other
virtual PCI busses like Hyper-V's virtual PCI bus (see for example
drivers/pci/controller/pci-hyperv.c:create_root_hv_pci_bus()).
Having zbus registration separate from scanning allows us to return
fully initialized but still disabled zdevs from zpci_create_device()
which can then be configured just as we would configure a zdev from
standby (minus the SCLP Configure already done by the platform). There
is still the exception that a PCI function with non-zero devfn can be
plugged before its PCI bus, which depends on the function with zero
devfn, is created. In this case the zdev returend from
zpci_create_device() is still missing its bus, hotplug slot, and
resources which need to be created later but at least it doesn't wait in
the enabled state and can otherwise be treated as initialized.
With this we also separate the initial PCI scan using CLP List PCI
Functions into two phases. In the CLP loop's callback we only register
each function with a virtual zbus creating the latter as needed. Then,
after we have built this virtual PCI topology based on our list of
zbusses, we can make use of the common code functionality to scan each
complete zbus as a separate child bus.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Acked-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
In a later change we will first collect all PCI functions from the CLP
List PCI functions call, then register them to/creating the relevant
zbus. Then only after we've created our virtual bus structure will we
scan all zbusses iterating over the zbus list. Since scanning is
relatively slow a spinlock is a bad fit for protecting the
loop over the devices on the zbus. Furthermore doing the probing on the
bus we need to use pci_lock_rescan_remove() as devices are added to
the PCI subsystem and that is a mutex which can't be locked nested
inside a spinlock section. Note that the contention of this lock should
be very low either way as zbusses are only added/removed concurrently on
hotplug events.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
In the existing code the creation of the PCI bus and the scanning of
function zero all happens in zpci_scan_bus(). This in turn requires
functions to be enabled and their resources to be available before the
PCI bus is even created.
This not only means that functions are enabled long before they are
actually made available to the common PCI subsystem. In case of
functions with non-zero devfn which appeared before the function with
devfn zero they can wait arbitrarily long in this enabled but not
scanned state.
Fix this by separating the creation of the PCI bus from scanning it and
only prepare, that is enable and setup MMIO bus resources, functions
just before they are scanned. As they may be scanned multiple times
track if we already created resources in the zdev.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Acked-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Pull setting the maximum bus speed and multifunction attribute into
zpci_bus_scan() in preparation for handling bus creation separately
from scanning the bus.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Acked-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
To match zpci_bus_scan_device() and the PCI common code terminology and
to remove some code duplication, we pull the multiple uses of
pci_scan_single_device() into a function. For now this has the side
effect of adding each device to the PCI bus separately and locking and
unlocking the rescan/remove lock for each instead of just once per bus.
This is clearly less efficient but provides a correct intermediate
behavior until a follow on change does both the adding and scanning only
once per bus.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Acked-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
On s390 each PCI device has a user-defined ID (UID) exposed under
/sys/bus/pci/devices/<dev>/uid. This ID was designed to serve as the PCI
device's primary index and to match the device within Linux to the
device configured in the hypervisor. To serve as a primary identifier
the UID must be unique within the Linux instance, this is guaranteed by
the platform if and only if the UID Uniqueness Checking flag is set
within the CLP List PCI Functions response.
While the UID has been exposed to userspace since commit ac4995b9d570
("s390/pci: add some new arch specific pci attributes") whether or not
the platform guarantees its uniqueness for the lifetime of the Linux
instance while defined is not visible from userspace. Remedy this by
exposing this as a per device attribute at
/sys/bus/pci/devices/<dev>/uid_is_unique
Keeping this a per device attribute allows for maximum flexibility if we
ever end up with some devices not having a UID or not enjoying the
guaranteed uniqueness.
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Viktor Mihajlovski <mihajlov@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
In commit dee60c0dbc83 ("s390/pci: add zpci_event_hard_deconfigured()")
we added a zdev_enabled() check to what was previously an uncoditional
call to zpci_disable_device(). There are two problems with that. Firstly
zpci_had_deconfigured() is only called on event 0x0304 for which the
device is always already disabled by the platform so it is always false.
Secondly zpci_disable_device() not only disables the device but also
calls zpci_dma_exit_device() which is thus not called and we leak the
DMA tables.
Fix this by calling zpci_disable_device() unconditionally to perform
Linux side cleanup including the freeing of DMA tables.
Fixes: dee60c0dbc83 ("s390/pci: add zpci_event_hard_deconfigured()")
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Acked-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
The zpci_remove_device() function removes the device from the PCI common
code core which is an operation dealing primarily with the zbus and PCI
bus code. With that and to match an upcoming refactoring of the
symmetric scanning part move it to the bus code.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
A zPCI event with PEC 0x0301 for an existing zPCI device goes through
the same actions as enable_slot(). Similarly a zPCI event with PEC
0x0303 does the same steps as disable_slot().
We can thus unify both actions as zpci_configure_device() respectively
zpci_deconfigure_device().
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Extract the handling of PEC 0x0304 into a function and make sure we only
attempt to disable the function if it is enabled. Also check for errors
returned by zpci_disable_device() and leave the function alone if there
are any.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
When zpci_release_device() is called on a zPCI function that is still
configured it would not be deconfigured. Until now this hasn't caused
any problems because zpci_zdev_put() is only ever called for devices
in Standby or Reserved. Fix it by adding sclp_pci_deconfigure() to the
switch when in Configured state.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
The current zdev->state mixes the configuration states supported by CLP
with an additional Online state which is used inconsistently to include
enabled zPCI functions which are not yet visible to the common PCI
subsytem. In preparation for a clean separation between architected
configuration states and fine grained function states remove the Online
function state.
Where we previously checked for Online it is more accurate to check if
the function is enabled to avoid an edge case where a disabled device
was still treated as Online. This also simplifies checks whether
a function is configured as this is now directly reflected by its
function state.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
In commit 05bc1be6db4b2 ("s390/pci: create zPCI bus") we removed the
pci_dev_put() call matching the earlier pci_get_slot() done as part of
__zpci_event_availability(). This was based on the wrong understanding
that the device_put() done as part of pci_destroy_device() would counter
the pci_get_slot() when it only counters the initial reference. This
same understanding and existing bad example also lead to not doing
a pci_dev_put() in zpci_remove_device().
Since releasing the PCI devices, unlike releasing the PCI slot, does not
print any debug message for testing I added one in pci_release_dev().
This revealed that we are indeed leaking the PCI device on PCI
hotunplug. Further testing also revealed another missing pci_dev_put() in
disable_slot().
Fix this by adding the missing pci_dev_put() in disable_slot() and fix
zpci_remove_device() with the correct pci_dev_put() calls. Also instead
of calling pci_get_slot() in __zpci_event_availability() to determine if
a PCI device is registered and then doing the same again in
zpci_remove_device() do this once in zpci_remove_device() which makes
sure that the pdev in __zpci_event_availability() is only used for the
result of pci_scan_single_device() which does not need a reference count
decremnt as its ownership goes to the PCI bus.
Also move the check if zdev->zbus->bus is set into zpci_remove_device()
since it may be that we're removing a device with devfn != 0 which never
had a PCI bus. So we can still set the pdev->error_state to indicate
that the device is not usable anymore, add a flag to set the error state.
Fixes: 05bc1be6db4b2 ("s390/pci: create zPCI bus")
Cc: <stable@vger.kernel.org> # 5.8+: e1bff843cde6 s390/pci: remove superfluous zdev->zbus check
Cc: <stable@vger.kernel.org> # 5.8+: ba764dd703fe s390/pci: refactor zpci_create_device()
Cc: <stable@vger.kernel.org> # 5.8+
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Vasily Gorbik:
- Convert to using the generic entry infrastructure.
- Add vdso time namespace support.
- Switch s390 and alpha to 64-bit ino_t. As discussed at
https://lore.kernel.org/linux-mm/YCV7QiyoweJwvN+m@osiris/
- Get rid of expensive stck (store clock) usages where possible.
Utilize cpu alternatives to patch stckf when supported.
- Make tod_clock usage less error prone by converting it to a union and
rework code which is using it.
- Machine check handler fixes and cleanups.
- Drop couple of minor inline asm optimizations to fix clang build.
- Default configs changes notably to make libvirt happy.
- Various changes to rework and improve qdio code.
- Other small various fixes and improvements all over the code.
* tag 's390-5.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (68 commits)
s390/qdio: remove 'merge_pending' mechanism
s390/qdio: improve handling of PENDING buffers for QEBSM devices
s390/qdio: rework q->qdio_error indication
s390/qdio: inline qdio_kick_handler()
s390/time: remove get_tod_clock_ext()
s390/crypto: use store_tod_clock_ext()
s390/hypfs: use store_tod_clock_ext()
s390/debug: use union tod_clock
s390/kvm: use union tod_clock
s390/vdso: use union tod_clock
s390/time: convert tod_clock_base to union
s390/time: introduce new store_tod_clock_ext()
s390/time: rename store_tod_clock_ext() and use union tod_clock
s390/time: introduce union tod_clock
s390,alpha: switch to 64-bit ino_t
s390: split cleanup_sie
s390: use r13 in cleanup_sie as temp register
s390: fix kernel asce loading when sie is interrupted
s390: add stack for machine check handler
s390: use WRITE_ONCE when re-allocating async stack
...
|
|
Currently zpci_create_device() is only called in clp_add_pci_device()
which allocates the memory for the struct zpci_dev being created. There
is little separation of concerns as only both functions together can
create a zpci_dev and the only CLP specific code in
clp_add_pci_device() is a call to clp_query_pci_fn().
Improve this by removing clp_add_pci_device() and refactor
zpci_create_device() such that it alone creates and initializes the
zpci_dev given the FID and Function Handle. For this we need to make
clp_query_pci_fn() non-static. While at it remove the function handle
parameter since we can just take that from the zpci_dev. Also move
adding to the zpci_list to after the zdev has been fully created which
eliminates a window where a partially initialized zdev can be found by
get_zdev_by_fid().
Acked-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
