| Age | Commit message (Collapse) | Author |
|---|
|
Commit b38af4721f59 ("x86,mm: fix pte_special versus pte_numa") adjusted
the pte_special check to take into account that a special pte had
SPECIAL and neither PRESENT nor PROTNONE. Now that NUMA hinting PTEs
are no longer modifying _PAGE_PRESENT it should be safe to restore the
original pte_special behaviour.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dave Jones <davej@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Kirill Shutemov <kirill.shutemov@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch removes the NUMA PTE bits and associated helpers. As a
side-effect it increases the maximum possible swap space on x86-64.
One potential source of problems is races between the marking of PTEs
PROT_NONE, NUMA hinting faults and migration. It must be guaranteed that
a PTE being protected is not faulted in parallel, seen as a pte_none and
corrupting memory. The base case is safe but transhuge has problems in
the past due to an different migration mechanism and a dependance on page
lock to serialise migrations and warrants a closer look.
task_work hinting update parallel fault
------------------------ --------------
change_pmd_range
change_huge_pmd
__pmd_trans_huge_lock
pmdp_get_and_clear
__handle_mm_fault
pmd_none
do_huge_pmd_anonymous_page
read? pmd_lock blocks until hinting complete, fail !pmd_none test
write? __do_huge_pmd_anonymous_page acquires pmd_lock, checks pmd_none
pmd_modify
set_pmd_at
task_work hinting update parallel migration
------------------------ ------------------
change_pmd_range
change_huge_pmd
__pmd_trans_huge_lock
pmdp_get_and_clear
__handle_mm_fault
do_huge_pmd_numa_page
migrate_misplaced_transhuge_page
pmd_lock waits for updates to complete, recheck pmd_same
pmd_modify
set_pmd_at
Both of those are safe and the case where a transhuge page is inserted
during a protection update is unchanged. The case where two processes try
migrating at the same time is unchanged by this series so should still be
ok. I could not find a case where we are accidentally depending on the
PTE not being cleared and flushed. If one is missed, it'll manifest as
corruption problems that start triggering shortly after this series is
merged and only happen when NUMA balancing is enabled.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Tested-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dave Jones <davej@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Kirill Shutemov <kirill.shutemov@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is a preparatory patch that introduces protnone helpers for automatic
NUMA balancing.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Tested-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dave Jones <davej@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Kirill Shutemov <kirill.shutemov@linux.intel.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
LKP has triggered a compiler warning after my recent patch "mm: account
pmd page tables to the process":
mm/mmap.c: In function 'exit_mmap':
>> mm/mmap.c:2857:2: warning: right shift count >= width of type [enabled by default]
The code:
> 2857 WARN_ON(mm_nr_pmds(mm) >
2858 round_up(FIRST_USER_ADDRESS, PUD_SIZE) >> PUD_SHIFT);
In this, on tile, we have FIRST_USER_ADDRESS defined as 0. round_up() has
the same type -- int. PUD_SHIFT.
I think the best way to fix it is to define FIRST_USER_ADDRESS as unsigned
long. On every arch for consistency.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching
Pull live patching infrastructure from Jiri Kosina:
"Let me provide a bit of history first, before describing what is in
this pile.
Originally, there was kSplice as a standalone project that implemented
stop_machine()-based patching for the linux kernel. This project got
later acquired, and the current owner is providing live patching as a
proprietary service, without any intentions to have their
implementation merged.
Then, due to rising user/customer demand, both Red Hat and SUSE
started working on their own implementation (not knowing about each
other), and announced first versions roughly at the same time [1] [2].
The principle difference between the two solutions is how they are
making sure that the patching is performed in a consistent way when it
comes to different execution threads with respect to the semantic
nature of the change that is being introduced.
In a nutshell, kPatch is issuing stop_machine(), then looking at
stacks of all existing processess, and if it decides that the system
is in a state that can be patched safely, it proceeds insterting code
redirection machinery to the patched functions.
On the other hand, kGraft provides a per-thread consistency during one
single pass of a process through the kernel and performs a lazy
contignuous migration of threads from "unpatched" universe to the
"patched" one at safe checkpoints.
If interested in a more detailed discussion about the consistency
models and its possible combinations, please see the thread that
evolved around [3].
It pretty quickly became obvious to the interested parties that it's
absolutely impractical in this case to have several isolated solutions
for one task to co-exist in the kernel. During a dedicated Live
Kernel Patching track at LPC in Dusseldorf, all the interested parties
sat together and came up with a joint aproach that would work for both
distro vendors. Steven Rostedt took notes [4] from this meeting.
And the foundation for that aproach is what's present in this pull
request.
It provides a basic infrastructure for function "live patching" (i.e.
code redirection), including API for kernel modules containing the
actual patches, and API/ABI for userspace to be able to operate on the
patches (look up what patches are applied, enable/disable them, etc).
It's relatively simple and minimalistic, as it's making use of
existing kernel infrastructure (namely ftrace) as much as possible.
It's also self-contained, in a sense that it doesn't hook itself in
any other kernel subsystem (it doesn't even touch any other code).
It's now implemented for x86 only as a reference architecture, but
support for powerpc, s390 and arm is already in the works (adding
arch-specific support basically boils down to teaching ftrace about
regs-saving).
Once this common infrastructure gets merged, both Red Hat and SUSE
have agreed to immediately start porting their current solutions on
top of this, abandoning their out-of-tree code. The plan basically is
that each patch will be marked by flag(s) that would indicate which
consistency model it is willing to use (again, the details have been
sketched out already in the thread at [3]).
Before this happens, the current codebase can be used to patch a large
group of secruity/stability problems the patches for which are not too
complex (in a sense that they don't introduce non-trivial change of
function's return value semantics, they don't change layout of data
structures, etc) -- this corresponds to LEAVE_FUNCTION &&
SWITCH_FUNCTION semantics described at [3].
This tree has been in linux-next since December.
[1] https://lkml.org/lkml/2014/4/30/477
[2] https://lkml.org/lkml/2014/7/14/857
[3] https://lkml.org/lkml/2014/11/7/354
[4] http://linuxplumbersconf.org/2014/wp-content/uploads/2014/10/LPC2014_LivePatching.txt
[ The core code is introduced by the three commits authored by Seth
Jennings, which got a lot of changes incorporated during numerous
respins and reviews of the initial implementation. All the followup
commits have materialized only after public tree has been created,
so they were not folded into initial three commits so that the
public tree doesn't get rebased ]"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching:
livepatch: add missing newline to error message
livepatch: rename config to CONFIG_LIVEPATCH
livepatch: fix uninitialized return value
livepatch: support for repatching a function
livepatch: enforce patch stacking semantics
livepatch: change ARCH_HAVE_LIVE_PATCHING to HAVE_LIVE_PATCHING
livepatch: fix deferred module patching order
livepatch: handle ancient compilers with more grace
livepatch: kconfig: use bool instead of boolean
livepatch: samples: fix usage example comments
livepatch: MAINTAINERS: add git tree location
livepatch: use FTRACE_OPS_FL_IPMODIFY
livepatch: move x86 specific ftrace handler code to arch/x86
livepatch: samples: add sample live patching module
livepatch: kernel: add support for live patching
livepatch: kernel: add TAINT_LIVEPATCH
|
|
Merge misc updates from Andrew Morton:
"Bite-sized chunks this time, to avoid the MTA ratelimiting woes.
- fs/notify updates
- ocfs2
- some of MM"
That laconic "some MM" is mainly the removal of remap_file_pages(),
which is a big simplification of the VM, and which gets rid of a *lot*
of random cruft and special cases because we no longer support the
non-linear mappings that it used.
From a user interface perspective, nothing has changed, because the
remap_file_pages() syscall still exists, it's just done by emulating the
old behavior by creating a lot of individual small mappings instead of
one non-linear one.
The emulation is slower than the old "native" non-linear mappings, but
nobody really uses or cares about remap_file_pages(), and simplifying
the VM is a big advantage.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (78 commits)
memcg: zap memcg_slab_caches and memcg_slab_mutex
memcg: zap memcg_name argument of memcg_create_kmem_cache
memcg: zap __memcg_{charge,uncharge}_slab
mm/page_alloc.c: place zone_id check before VM_BUG_ON_PAGE check
mm: hugetlb: fix type of hugetlb_treat_as_movable variable
mm, hugetlb: remove unnecessary lower bound on sysctl handlers"?
mm: memory: merge shared-writable dirtying branches in do_wp_page()
mm: memory: remove ->vm_file check on shared writable vmas
xtensa: drop _PAGE_FILE and pte_file()-related helpers
x86: drop _PAGE_FILE and pte_file()-related helpers
unicore32: drop pte_file()-related helpers
um: drop _PAGE_FILE and pte_file()-related helpers
tile: drop pte_file()-related helpers
sparc: drop pte_file()-related helpers
sh: drop _PAGE_FILE and pte_file()-related helpers
score: drop _PAGE_FILE and pte_file()-related helpers
s390: drop pte_file()-related helpers
parisc: drop _PAGE_FILE and pte_file()-related helpers
openrisc: drop _PAGE_FILE and pte_file()-related helpers
nios2: drop _PAGE_FILE and pte_file()-related helpers
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"We have a few new features this time, including a new SFI-based
cpufreq driver, a new devfreq driver for Tegra Activity Monitor, a new
devfreq class for providing its governors with raw utilization data
and a new ACPI driver for AMD SoCs.
Still, the majority of changes here are reworks of existing code to
make it more straightforward or to prepare it for implementing new
features on top of it. The primary example is the rework of ACPI
resources handling from Jiang Liu, Thomas Gleixner and Lv Zheng with
support for IOAPIC hotplug implemented on top of it, but there is
quite a number of changes of this kind in the cpufreq core, ACPICA,
ACPI EC driver, ACPI processor driver and the generic power domains
core code too.
The most active developer is Viresh Kumar with his cpufreq changes.
Specifics:
- Rework of the core ACPI resources parsing code to fix issues in it
and make using resource offsets more convenient and consolidation
of some resource-handing code in a couple of places that have grown
analagous data structures and code to cover the the same gap in the
core (Jiang Liu, Thomas Gleixner, Lv Zheng).
- ACPI-based IOAPIC hotplug support on top of the resources handling
rework (Jiang Liu, Yinghai Lu).
- ACPICA update to upstream release 20150204 including an interrupt
handling rework that allows drivers to install raw handlers for
ACPI GPEs which then become entirely responsible for the given GPE
and the ACPICA core code won't touch it (Lv Zheng, David E Box,
Octavian Purdila).
- ACPI EC driver rework to fix several concurrency issues and other
problems related to events handling on top of the ACPICA's new
support for raw GPE handlers (Lv Zheng).
- New ACPI driver for AMD SoCs analogous to the LPSS (Low-Power
Subsystem) driver for Intel chips (Ken Xue).
- Two minor fixes of the ACPI LPSS driver (Heikki Krogerus, Jarkko
Nikula).
- Two new blacklist entries for machines (Samsung 730U3E/740U3E and
510R) where the native backlight interface doesn't work correctly
while the ACPI one does (Hans de Goede).
- Rework of the ACPI processor driver's handling of idle states to
make the code more straightforward and less bloated overall (Rafael
J Wysocki).
- Assorted minor fixes related to ACPI and SFI (Andreas Ruprecht,
Andy Shevchenko, Hanjun Guo, Jan Beulich, Rafael J Wysocki, Yaowei
Bai).
- PCI core power management modification to avoid resuming (some)
runtime-suspended devices during system suspend if they are in the
right states already (Rafael J Wysocki).
- New SFI-based cpufreq driver for Intel platforms using SFI
(Srinidhi Kasagar).
- cpufreq core fixes, cleanups and simplifications (Viresh Kumar,
Doug Anderson, Wolfram Sang).
- SkyLake CPU support and other updates for the intel_pstate driver
(Kristen Carlson Accardi, Srinivas Pandruvada).
- cpufreq-dt driver cleanup (Markus Elfring).
- Init fix for the ARM big.LITTLE cpuidle driver (Sudeep Holla).
- Generic power domains core code fixes and cleanups (Ulf Hansson).
- Operating Performance Points (OPP) core code cleanups and kernel
documentation update (Nishanth Menon).
- New dabugfs interface to make the list of PM QoS constraints
available to user space (Nishanth Menon).
- New devfreq driver for Tegra Activity Monitor (Tomeu Vizoso).
- New devfreq class (devfreq_event) to provide raw utilization data
to devfreq governors (Chanwoo Choi).
- Assorted minor fixes and cleanups related to power management
(Andreas Ruprecht, Krzysztof Kozlowski, Rickard Strandqvist, Pavel
Machek, Todd E Brandt, Wonhong Kwon).
- turbostat updates (Len Brown) and cpupower Makefile improvement
(Sriram Raghunathan)"
* tag 'pm+acpi-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (151 commits)
tools/power turbostat: relax dependency on APERF_MSR
tools/power turbostat: relax dependency on invariant TSC
Merge branch 'pci/host-generic' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci into acpi-resources
tools/power turbostat: decode MSR_*_PERF_LIMIT_REASONS
tools/power turbostat: relax dependency on root permission
ACPI / video: Add disable_native_backlight quirk for Samsung 510R
ACPI / PM: Remove unneeded nested #ifdef
USB / PM: Remove unneeded #ifdef and associated dead code
intel_pstate: provide option to only use intel_pstate with HWP
ACPI / EC: Add GPE reference counting debugging messages
ACPI / EC: Add query flushing support
ACPI / EC: Refine command storm prevention support
ACPI / EC: Add command flushing support.
ACPI / EC: Introduce STARTED/STOPPED flags to replace BLOCKED flag
ACPI: add AMD ACPI2Platform device support for x86 system
ACPI / table: remove duplicate NULL check for the handler of acpi_table_parse()
ACPI / EC: Update revision due to raw handler mode.
ACPI / EC: Reduce ec_poll() by referencing the last register access timestamp.
ACPI / EC: Fix several GPE handling issues by deploying ACPI_GPE_DISPATCH_RAW_HANDLER mode.
ACPICA: Events: Enable APIs to allow interrupt/polling adaptive request based GPE handling model
...
|
|
We've replaced remap_file_pages(2) implementation with emulation. Nobody
creates non-linear mapping anymore.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen features and fixes from David Vrabel:
- Reworked handling for foreign (grant mapped) pages to simplify the
code, enable a number of additional use cases and fix a number of
long-standing bugs.
- Prefer the TSC over the Xen PV clock when dom0 (and the TSC is
stable).
- Assorted other cleanup and minor bug fixes.
* tag 'stable/for-linus-3.20-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (25 commits)
xen/manage: Fix USB interaction issues when resuming
xenbus: Add proper handling of XS_ERROR from Xenbus for transactions.
xen/gntdev: provide find_special_page VMA operation
xen/gntdev: mark userspace PTEs as special on x86 PV guests
xen-blkback: safely unmap grants in case they are still in use
xen/gntdev: safely unmap grants in case they are still in use
xen/gntdev: convert priv->lock to a mutex
xen/grant-table: add a mechanism to safely unmap pages that are in use
xen-netback: use foreign page information from the pages themselves
xen: mark grant mapped pages as foreign
xen/grant-table: add helpers for allocating pages
x86/xen: require ballooned pages for grant maps
xen: remove scratch frames for ballooned pages and m2p override
xen/grant-table: pre-populate kernel unmap ops for xen_gnttab_unmap_refs()
mm: add 'foreign' alias for the 'pinned' page flag
mm: provide a find_special_page vma operation
x86/xen: cleanup arch/x86/xen/mmu.c
x86/xen: add some __init annotations in arch/x86/xen/mmu.c
x86/xen: add some __init and static annotations in arch/x86/xen/setup.c
x86/xen: use correct types for addresses in arch/x86/xen/setup.c
...
|
|
* pm-tools:
tools/power turbostat: relax dependency on APERF_MSR
tools/power turbostat: relax dependency on invariant TSC
tools/power turbostat: decode MSR_*_PERF_LIMIT_REASONS
tools/power turbostat: relax dependency on root permission
cpupower Makefile change to help run the tool without 'make install'
|
|
* pm-cpufreq: (46 commits)
intel_pstate: provide option to only use intel_pstate with HWP
cpufreq-dt: Drop unnecessary check before cpufreq_cooling_unregister() invocation
cpufreq: Create for_each_governor()
cpufreq: Create for_each_policy()
cpufreq: Drop cpufreq_disabled() check from cpufreq_cpu_{get|put}()
cpufreq: Set cpufreq_cpu_data to NULL before putting kobject
intel_pstate: honor user space min_perf_pct override on resume
intel_pstate: respect cpufreq policy request
intel_pstate: Add num_pstates to sysfs
intel_pstate: expose turbo range to sysfs
intel_pstate: Add support for SkyLake
cpufreq: stats: drop unnecessary locking
cpufreq: stats: don't update stats on false notifiers
cpufreq: stats: don't update stats from show_trans_table()
cpufreq: stats: time_in_state can't be NULL in cpufreq_stats_update()
cpufreq: stats: create sysfs group once we are ready
cpufreq: remove CPUFREQ_UPDATE_POLICY_CPU notifications
cpufreq: stats: drop 'cpu' field of struct cpufreq_stats
cpufreq: Remove (now) unused 'last_cpu' from struct cpufreq_policy
cpufreq: stats: rename 'struct cpufreq_stats' objects as 'stats'
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 SoC updates from Ingo Molnar:
"Various Intel Atom SoC updates (mostly to enhance debuggability), plus
an apb_timer cleanup"
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: pmc_atom: Expose contents of PSS
x86: pmc_atom: Clean up init function
x86: pmc-atom: Remove unused macro
x86: pmc_atom: don%27t check for NULL twice
x86: pmc-atom: Assign debugfs node as soon as possible
x86/platform: Remove unused function from apb_timer.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fpu updates from Ingo Molnar:
"Initial round of kernel_fpu_begin/end cleanups from Oleg Nesterov,
plus a cleanup from Borislav Petkov"
* 'x86-fpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, fpu: Fix math_state_restore() race with kernel_fpu_begin()
x86, fpu: Don't abuse has_fpu in __kernel_fpu_begin/end()
x86, fpu: Introduce per-cpu in_kernel_fpu state
x86/fpu: Use a symbolic name for asm operand
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 asm changes from Ingo Molnar:
"The main changes in this cycle were the x86/entry and sysret
enhancements from Andy Lutomirski, see merge commits 772a9aca125 and
b57c0b5175dd for details"
[ Exectutive summary: IST exceptions that interrupt user space will run
on the regular kernel stack instead of the IST stack. Which
simplifies things particularly on return to user space.
The sysret cleanup ends up simplifying the logic on when we can use
sysret vs when we have to use iret. - Linus ]
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86_64, entry: Remove the syscall exit audit and schedule optimizations
x86_64, entry: Use sysret to return to userspace when possible
x86, traps: Fix ist_enter from userspace
x86, vdso: teach 'make clean' remove vdso64 binaries
x86_64 entry: Fix RCX for ptraced syscalls
x86: entry_64.S: fold SAVE_ARGS_IRQ macro into its sole user
x86: ia32entry.S: fix wrong symbolic constant usage: R11->ARGOFFSET
x86: entry_64.S: delete unused code
x86, mce: Get rid of TIF_MCE_NOTIFY and associated mce tricks
x86, traps: Add ist_begin_non_atomic and ist_end_non_atomic
x86: Clean up current_stack_pointer
x86, traps: Track entry into and exit from IST context
x86, entry: Switch stacks on a paranoid entry from userspace
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 APIC updates from Ingo Molnar:
"Continued fallout of the conversion of the x86 IRQ code to the
hierarchical irqdomain framework: more cleanups, simplifications,
memory allocation behavior enhancements, mainly in the interrupt
remapping and APIC code"
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (44 commits)
x86, init: Fix UP boot regression on x86_64
iommu/amd: Fix irq remapping detection logic
x86/acpi: Make acpi_[un]register_gsi_ioapic() depend on CONFIG_X86_LOCAL_APIC
x86: Consolidate boot cpu timer setup
x86/apic: Reuse apic_bsp_setup() for UP APIC setup
x86/smpboot: Sanitize uniprocessor init
x86/smpboot: Move apic init code to apic.c
init: Get rid of x86isms
x86/apic: Move apic_init_uniprocessor code
x86/smpboot: Cleanup ioapic handling
x86/apic: Sanitize ioapic handling
x86/ioapic: Add proper checks to setp/enable_IO_APIC()
x86/ioapic: Provide stub functions for IOAPIC%3Dn
x86/smpboot: Move smpboot inlines to code
x86/x2apic: Use state information for disable
x86/x2apic: Split enable and setup function
x86/x2apic: Disable x2apic from nox2apic setup
x86/x2apic: Add proper state tracking
x86/x2apic: Clarify remapping mode for x2apic enablement
x86/x2apic: Move code in conditional region
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux into pm-cpufreq
Pull SFI-based cpufreq driver for v3.20 from Len Brown.
* 'sfi' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
cpufreq: Add SFI based cpufreq driver support
SFI: fix compiler warnings
|
|
The Processor generation code-named Haswell
added MSR_{CORE | GFX | RING}_PERF_LIMIT_REASONS
to explain when and how the processor limits frequency.
turbostat -v
will now decode these bits.
Each MSR has an "Active" set of bits which describe
current conditions, and a "Logged" set of bits,
which describe what has happened since last cleared.
Turbostat currently doesn't clear the log bits.
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Some PCI device drivers assume that pci_dev->irq won't change after
calling pci_disable_device() and pci_enable_device() during suspend and
resume.
Commit c03b3b0738a5 ("x86, irq, mpparse: Release IOAPIC pin when
PCI device is disabled") frees PCI IRQ resources when pci_disable_device()
is called and reallocate IRQ resources when pci_enable_device() is
called again. This breaks above assumption. So commit 3eec595235c1
("x86, irq, PCI: Keep IRQ assignment for PCI devices during
suspend/hibernation") and 9eabc99a635a ("x86, irq, PCI: Keep IRQ
assignment for runtime power management") fix the issue by avoiding
freeing/reallocating IRQ resources during PCI device suspend/resume.
They achieve this by checking dev.power.is_prepared and
dev.power.runtime_status. PM maintainer, Rafael, then pointed out that
it's really an ugly fix which leaking PM internal state information to
IRQ subsystem.
Recently David Vrabel <david.vrabel@citrix.com> also reports an
regression in pciback driver caused by commit cffe0a2b5a34 ("x86, irq:
Keep balance of IOAPIC pin reference count"). Please refer to:
http://lkml.org/lkml/2015/1/14/546
So this patch refine the way to release PCI IRQ resources. Instead of
releasing PCI IRQ resources in pci_disable_device()/
pcibios_disable_device(), we now release it at driver unbinding
notification BUS_NOTIFY_UNBOUND_DRIVER. In other word, we only release
PCI IRQ resources when there's no driver bound to the PCI device, and
it keeps the assumption that pci_dev->irq won't through multiple
invocation of pci_enable_device()/pci_disable_device().
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Rename CONFIG_LIVE_PATCHING to CONFIG_LIVEPATCH to make the naming of
the config and the code more consistent.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The new hw_breakpoint bits are now ready for v3.20, merge them
into the main branch, to avoid conflicts.
Conflicts:
tools/perf/Documentation/perf-record.txt
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/luto/linux into x86/asm
Pull x86/entry enhancements from Andy Lutomirski:
" This is my accumulated x86 entry work, part 1, for 3.20. The meat
of this is an IST rework. When an IST exception interrupts user
space, we will handle it on the per-thread kernel stack instead of
on the IST stack. This sounds messy, but it actually simplifies the
IST entry/exit code, because it eliminates some ugly games we used
to play in order to handle rescheduling, signal delivery, etc on the
way out of an IST exception.
The IST rework introduces proper context tracking to IST exception
handlers. I haven't seen any bug reports, but the old code could
have incorrectly treated an IST exception handler as an RCU extended
quiescent state.
The memory failure change (included in this pull request with
Borislav and Tony's permission) eliminates a bunch of code that
is no longer needed now that user memory failure handlers are
called in process context.
Finally, this includes a few on Denys' uncontroversial and Obviously
Correct (tm) cleanups.
The IST and memory failure changes have been in -next for a while.
LKML references:
IST rework:
http://lkml.kernel.org/r/cover.1416604491.git.luto@amacapital.net
Memory failure change:
http://lkml.kernel.org/r/54ab2ffa301102cd6e@agluck-desk.sc.intel.com
Denys' cleanups:
http://lkml.kernel.org/r/1420927210-19738-1-git-send-email-dvlasenk@redhat.com
"
This tree semantically depends on and is based on the following RCU commit:
734d16801349 ("rcu: Make rcu_nmi_enter() handle nesting")
... and for that reason won't be pushed upstream before the RCU bits hit Linus's tree.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The scratch frame mappings for ballooned pages and the m2p override
are broken. Remove them in preparation for replacing them with
simpler mechanisms that works.
The scratch pages did not ensure that the page was not in use. In
particular, the foreign page could still be in use by hardware. If
the guest reused the frame the hardware could read or write that
frame.
The m2p override did not handle the same frame being granted by two
different grant references. Trying an M2P override lookup in this
case is impossible.
With the m2p override removed, the grant map/unmap for the kernel
mappings (for x86 PV) can be easily batched in
set_foreign_p2m_mapping() and clear_foreign_p2m_mapping().
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
|
|
When unmapping grants, instead of converting the kernel map ops to
unmap ops on the fly, pre-populate the set of unmap ops.
This allows the grant unmap for the kernel mappings to be trivially
batched in the future.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
|
|
The Witcher 2 did something like this to allocate a TLS segment index:
struct user_desc u_info;
bzero(&u_info, sizeof(u_info));
u_info.entry_number = (uint32_t)-1;
syscall(SYS_set_thread_area, &u_info);
Strictly speaking, this code was never correct. It should have set
read_exec_only and seg_not_present to 1 to indicate that it wanted
to find a free slot without putting anything there, or it should
have put something sensible in the TLS slot if it wanted to allocate
a TLS entry for real. The actual effect of this code was to
allocate a bogus segment that could be used to exploit espfix.
The set_thread_area hardening patches changed the behavior, causing
set_thread_area to return -EINVAL and crashing the game.
This changes set_thread_area to interpret this as a request to find
a free slot and to leave it empty, which isn't *quite* what the game
expects but should be close enough to keep it working. In
particular, using the code above to allocate two segments will
allocate the same segment both times.
According to FrostbittenKing on Github, this fixes The Witcher 2.
If this somehow still causes problems, we could instead allocate
a limit==0 32-bit data segment, but that seems rather ugly to me.
Fixes: 41bdc78544b8 x86/tls: Validate TLS entries to protect espfix
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Cc: stable@vger.kernel.org
Cc: torvalds@linux-foundation.org
Link: http://lkml.kernel.org/r/0cb251abe1ff0958b8e468a9a9a905b80ae3a746.1421954363.git.luto@amacapital.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
32-bit programs don't have an lm bit in their ABI, so they can't
reliably cause LDT_empty to return true without resorting to memset.
They shouldn't need to do this.
This should fix a longstanding, if minor, issue in all 64-bit kernels
as well as a potential regression in the TLS hardening code.
Fixes: 41bdc78544b8 x86/tls: Validate TLS entries to protect espfix
Cc: stable@vger.kernel.org
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Cc: torvalds@linux-foundation.org
Link: http://lkml.kernel.org/r/72a059de55e86ad5e2935c80aa91880ddf19d07c.1421954363.git.luto@amacapital.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The 3.19 merge window saw some TLB modifications merged which caused a
performance regression. They were fixed in commit 045bbb9fa.
Once that fix was applied, I also noticed that there was a small
but intermittent regression still present. It was not present
consistently enough to bisect reliably, but I'm fairly confident
that it came from (my own) MPX patches. The source was reading
a relatively unused field in the mm_struct via arch_unmap.
I also noted that this code was in the main instruction flow of
do_munmap() and probably had more icache impact than we want.
This patch does two things:
1. Adds a static (via Kconfig) and dynamic (via cpuid) check
for MPX with cpu_feature_enabled(). This keeps us from
reading that cacheline in the mm and trades it for a check
of the global CPUID variables at least on CPUs without MPX.
2. Adds an unlikely() to ensure that the MPX call ends up out
of the main instruction flow in do_munmap(). I've added
a detailed comment about why this was done and why we want
it even on systems where MPX is present.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: luto@amacapital.net
Cc: Dave Hansen <dave@sr71.net>
Link: http://lkml.kernel.org/r/20150108223021.AEEAB987@viggo.jf.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Extend apic_bsp_setup() so the same code flow can be used for
APIC_init_uniprocessor().
Folded Jiangs fix to provide proper ordering of the UP setup.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/20150115211704.084765674@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
We better provide proper functions which implement the required code
flow in the apic code rather than letting the smpboot code open code
it. That allows to make more functions static and confines the APIC
functionality to apic.c where it belongs.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Borislav Petkov <bp@alien8.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/20150115211703.907616730@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
To avoid lots of ifdeffery provide proper stubs for setup_IO_APIC(),
enable_IO_APIC() and setup_ioapic_dest().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Borislav Petkov <bp@alien8.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/20150115211703.397170414@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
No point for a separate header file.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/20150115211703.304126687@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
enable_x2apic() is a convoluted unreadable mess because it is used for
both enablement in early boot and for setup in cpu_init().
Split the code into x2apic_enable() for enablement and x2apic_setup()
for setup of (secondary cpus). Make use of the new state tracking to
simplify the logic.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/20150115211703.129287153@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
There is no point in postponing the hardware disablement of x2apic. It
can be disabled right away in the nox2apic setup function.
Disable it right away and set the state to DISABLED . This allows to
remove all the nox2apic conditionals all over the place.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/20150115211703.051214090@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
No point in having try_to_enable_x2apic() outside of the
CONFIG_X86_X2APIC section and having inline functions and more ifdefs
to deal with it. Move the code into the existing ifdef section and
remove the inline cruft.
Fixup the printk about not enabling interrupt remapping as suggested
by Boris.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/20150115211702.795388613@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
No point in delaying the x2apic detection for the CONFIG_X86_X2APIC=n
case to enable_IR_x2apic(). We rather detect that before we try to
setup anything there.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/20150115211702.702479404@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The x2apic_preenabled flag is just a horrible hack and if X2APIC
support is disabled it does not reflect the actual hardware
state. Check the hardware instead.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/20150115211702.541280622@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
No point in having a static variable around which is always 0. Let the
compiler optimize code out if disabled.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Borislav Petkov <bp@alien8.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/20150115211702.363274310@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
enable_IR_x2apic() grew a open coded x2apic detection. Implement a
proper helper function which shares the code with the already existing
x2apic_enabled().
Made it use rdmsrl_safe as suggested by Boris.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/20150115211702.285038186@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
math_state_restore() can race with kernel_fpu_begin() if irq comes
right after __thread_fpu_begin(), __save_init_fpu() will overwrite
fpu->state we are going to restore.
Add 2 simple helpers, kernel_fpu_disable() and kernel_fpu_enable()
which simply set/clear in_kernel_fpu, and change math_state_restore()
to exclude kernel_fpu_begin() in between.
Alternatively we could use local_irq_save/restore, but probably these
new helpers can have more users.
Perhaps they should disable/enable preemption themselves, in this case
we can remove preempt_disable() in __restore_xstate_sig().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Cc: matt.fleming@intel.com
Cc: bp@suse.de
Cc: pbonzini@redhat.com
Cc: luto@amacapital.net
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Suresh Siddha <sbsiddha@gmail.com>
Link: http://lkml.kernel.org/r/20150115192028.GD27332@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
interrupted_kernel_fpu_idle() tries to detect if kernel_fpu_begin()
is safe or not. In particular it should obviously deny the nested
kernel_fpu_begin() and this logic looks very confusing.
If use_eager_fpu() == T we rely on a) __thread_has_fpu() check in
interrupted_kernel_fpu_idle(), and b) on the fact that _begin() does
__thread_clear_has_fpu().
Otherwise we demand that the interrupted task has no FPU if it is in
kernel mode, this works because __kernel_fpu_begin() does clts() and
interrupted_kernel_fpu_idle() checks X86_CR0_TS.
Add the per-cpu "bool in_kernel_fpu" variable, and change this code
to check/set/clear it. This allows to do more cleanups and fixes, see
the next changes.
The patch also moves WARN_ON_ONCE() under preempt_disable() just to
make this_cpu_read() look better, this is not really needed. And in
fact I think we should move it into __kernel_fpu_begin().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Cc: matt.fleming@intel.com
Cc: bp@suse.de
Cc: pbonzini@redhat.com
Cc: luto@amacapital.net
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Suresh Siddha <sbsiddha@gmail.com>
Link: http://lkml.kernel.org/r/20150115191943.GB27332@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The PSS register reflects the power state of each island on SoC. It would be
useful to know which of the islands is on or off at the momemnt.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Aubrey Li <aubrey.li@linux.intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Kumar P. Mahesh <mahesh.kumar.p@intel.com>
Link: http://lkml.kernel.org/r/1421253575-22509-6-git-send-email-andriy.shevchenko@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Xen overrides __acpi_register_gsi and leaves __acpi_unregister_gsi as is.
That means, an IRQ allocated by acpi_register_gsi_xen_hvm() or
acpi_register_gsi_xen() will be freed by acpi_unregister_gsi_ioapic(),
which may cause undesired effects. So override __acpi_unregister_gsi to
NULL for safety.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Cc: Tony Luck <tony.luck@intel.com>
Cc: xen-devel@lists.xenproject.org
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Graeme Gregory <graeme.gregory@linaro.org>
Cc: Lv Zheng <lv.zheng@intel.com>
Link: http://lkml.kernel.org/r/1421720467-7709-4-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Simplify irq_remapping code by killing irq_remapping_supported() and
related interfaces.
Joerg posted a similar patch at https://lkml.org/lkml/2014/12/15/490,
so assume an signed-off from Joerg.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Rientjes <rientjes@google.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Jan Beulich <JBeulich@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Oren Twaig <oren@scalemp.com>
Link: http://lkml.kernel.org/r/1420615903-28253-14-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
enable_IR_x2apic() calls setup_irq_remapping_ops() which by default
installs the intel dmar remapping ops and then calls the amd iommu irq
remapping prepare callback to figure out whether we are running on an
AMD machine with irq remapping hardware.
Right after that it calls irq_remapping_prepare() which pointlessly
checks:
if (!remap_ops || !remap_ops->prepare)
return -ENODEV;
and then calls
remap_ops->prepare()
which is silly in the AMD case as it got called from
setup_irq_remapping_ops() already a few microseconds ago.
Simplify this and just collapse everything into
irq_remapping_prepare().
The irq_remapping_prepare() remains still silly as it assigns blindly
the intel ops, but that's not scope of this patch.
The scope here is to move the preperatory work, i.e. memory
allocations out of the atomic section which is required to enable irq
remapping.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Borislav Petkov <bp@alien8.de>
Acked-and-tested-by: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: Joerg Roedel <jroedel@suse.de>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Jan Beulich <JBeulich@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Oren Twaig <oren@scalemp.com>
Cc: x86@kernel.org
Link: http://lkml.kernel.org/r/20141205084147.232633738@linutronix.de
Link: http://lkml.kernel.org/r/1420615903-28253-2-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
A define, two macros and an unreferenced bit of assembly are gone.
Acked-by: Borislav Petkov <bp@suse.de>
CC: Linus Torvalds <torvalds@linux-foundation.org>
CC: Oleg Nesterov <oleg@redhat.com>
CC: "H. Peter Anvin" <hpa@zytor.com>
CC: Andy Lutomirski <luto@amacapital.net>
CC: Frederic Weisbecker <fweisbec@gmail.com>
CC: X86 ML <x86@kernel.org>
CC: Alexei Starovoitov <ast@plumgrid.com>
CC: Will Drewry <wad@chromium.org>
CC: Kees Cook <keescook@chromium.org>
CC: linux-kernel@vger.kernel.org
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
|
|
We are aborting a build in case when gcc doesn't support fentry on x86_64
(regs->ip modification can't really reliably work with mcount).
This however breaks allmodconfig for people with older gccs that don't
support -mfentry.
Turn the build-time failure into runtime failure, resulting in the whole
infrastructure not being initialized if CC_USING_FENTRY is unset.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
|
|
We now switch to the kernel stack when a machine check interrupts
during user mode. This means that we can perform recovery actions
in the tail of do_machine_check()
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
|
|
In some IST handlers, if the interrupt came from user mode,
we can safely enable preemption. Add helpers to do it safely.
This is intended to be used my the memory failure code in
do_machine_check.
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
|
|
There's no good reason for it to be a macro, and x86_64 will want to
use it, so it should be in a header.
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
|
|
We currently pretend that IST context is like standard exception
context, but this is incorrect. IST entries from userspace are like
standard exceptions except that they use per-cpu stacks, so they are
atomic. IST entries from kernel space are like NMIs from RCU's
perspective -- they are not quiescent states even if they
interrupted the kernel during a quiescent state.
Add and use ist_enter and ist_exit to track IST context. Even
though x86_32 has no IST stacks, we track these interrupts the same
way.
This fixes two issues:
- Scheduling from an IST interrupt handler will now warn. It would
previously appear to work as long as we got lucky and nothing
overwrote the stack frame. (I don't know of any bugs in this
that would trigger the warning, but it's good to be on the safe
side.)
- RCU handling in IST context was dangerous. As far as I know,
only machine checks were likely to trigger this, but it's good to
be on the safe side.
Note that the machine check handlers appears to have been missing
any context tracking at all before this patch.
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Frédéric Weisbecker <fweisbec@gmail.com>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/luto/linux into x86/urgent
Pull VDSO fix from Andy Lutomirski:
"This is hopefully the last vdso fix for 3.19. It should be very
safe (it just adds a volatile).
I don't think it fixes an actual bug (the __getcpu calls in the
pvclock code may not have been needed in the first place), but
discussion on that point is ongoing.
It also fixes a big performance issue in 3.18 and earlier in which
the lsl instructions in vclock_gettime got hoisted so far up the
function that they happened even when the function they were in was
never called. n 3.19, the performance issue seems to be gone due to
the whims of my compiler and some interaction with a branch that's
now gone.
I'll hopefully have a much bigger overhaul of the pvclock code
for 3.20, but it needs careful review."
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
