| Age | Commit message (Collapse) | Author |
|---|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Intel Xeon Phi processors (KNL and KNM) support PPIN as well, so add their
CPUIDs to the whitelist of supported processors.
Signed-off-by: Piotr Luc <piotr.luc@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170408172004.8463-1-piotr.luc@intel.com
Link: http://lkml.kernel.org/r/20170413201056.10525-1-bp@alien8.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Intel Xeons from Ivy Bridge onwards support a processor identification
number set in the factory. To the user this is a handy unique number to
identify a particular CPU. Intel can decode this to the fab/production
run to track errors. On systems that have it, include it in the machine
check record. I'm told that this would be helpful for users that run
large data centers with multi-socket servers to keep track of which CPUs
are seeing errors.
Boris:
* Add some clarifying comments and spacing.
* Mask out [63:2] in the disabled-but-not-locked case
* Call the MSR variable "val" for more readability.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: x86-ml <x86@kernel.org>
Link: http://lkml.kernel.org/r/20161123114855.njguoaygp3qnbkia@pd.tnic
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
We did have logic in the MCE code which would TSC-timestamp an error
record only when it is exact - i.e., when it wasn't detected by polling.
This isn't the case anymore. So let's fix that:
We have a valid TSC timestamp in the error record only when it has been
a precise detection, i.e., either in the #MC handler or in one of the
interrupt handlers (thresholding, deferred, ...).
All other error records still have mce.time which contains the wall
time in order to be able to place the error record in time at least
approximately.
Also, this fixes another bug where machine_check_poll() would clear
mce.tsc unconditionally even if we requested precise MCP_TIMESTAMP
logging.
The proper fix would be to generate timestamp only when it has been
requested and not always. But that would require a more thorough code
audit of all mce_gather_info/mce_setup() users. Add a FIXME for now.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony <tony.luck@intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: kernel test robot <xiaolong.ye@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: lkp@01.org
Link: http://lkml.kernel.org/r/20161110131053.kybsijfs5venpjnf@pd.tnic
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: iommu@lists.linux-foundation.org
Cc: linux-pm@vger.kernel.org
Cc: oprofile-list@lists.sf.net
Link: http://lkml.kernel.org/r/1459801503-15600-8-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Zhang Liguang reported the following issue:
1) System detects a CMCI storm on the current CPU.
2) Kernel disables the CMCI interrupt on banks owned by the
current CPU and switches to poll mode
3) After the CMCI storm subsides, kernel switches back to
interrupt mode
4) We expect the system to reenable the CMCI interrupt on banks
owned by the current CPU
mce_intel_adjust_timer
|-> cmci_reenable
|-> cmci_discover # owned banks are ignored here
static void cmci_discover(int banks)
...
for (i = 0; i < banks; i++) {
...
if (test_bit(i, owned)) # ownd banks is ignore here
continue;
So convert cmci_storm_disable_banks() to
cmci_toggle_interrupt_mode() which controls whether to enable or
disable CMCI interrupts with its argument.
NB: We cannot clear the owned bit because the banks won't be
polled, otherwise. See:
27f6c573e0f7 ("x86, CMCI: Add proper detection of end of CMCI storms")
for more info.
Reported-by: Zhang Liguang <zhangliguang@huawei.com>
Signed-off-by: Xie XiuQi <xiexiuqi@huawei.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org> # v3.15+
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: huawei.libin@huawei.com
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: rui.xiang@huawei.com
Link: http://lkml.kernel.org/r/1439396985-12812-10-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
kexec could boot a kernel that could be legacy with no knowledge
of LMCE. Hence we should make sure we clear LMCE optin before
kexec reboot.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@amd.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1439396985-12812-9-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Printing in MCE context is a no-no, currently, as printk() is
not NMI-safe. If some of the notifiers on the MCE chain call do
so, we may deadlock. In order to avoid that, delay printk() to
process context where it is safe.
Reported-by: Xie XiuQi <xiexiuqi@huawei.com>
Signed-off-by: Chen, Gong <gong.chen@linux.intel.com>
[ Fold in subsequent patch from Boris for early boot logging. ]
Signed-off-by: Tony Luck <tony.luck@intel.com>
[ Kick irq_work in mce_log() directly. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1439396985-12812-6-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Add the necessary changes to do_machine_check() to be able to
process MCEs signaled as local MCEs. Typically, only recoverable
errors (SRAR type) will be Signaled as LMCE. The architecture
does not restrict to only those errors, however.
When errors are signaled as LMCE, there is no need for the MCE
handler to perform rendezvous with other logical processors
unlike earlier processors that would broadcast machine check
errors.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1433436928-31903-17-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Initialize and prepare for handling LMCEs. Add a boot-time
option to disable LMCEs.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
[ Simplify stuff, align statements for better readability, reflow comments; kill
unused lmce_clear(); save us an MSR write if LMCE is already enabled. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1433436928-31903-16-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Initially, this started with the yet another report about a race
condition in the CMCI storm adaptive period length thing. Yes, we have
to admit, it is fragile and error prone. So let's simplify it.
The simpler logic is: now, after we enter storm mode, we go straight to
polling with CMCI_STORM_INTERVAL, i.e. once a second. We remain in storm
mode as long as we see errors being logged while polling.
Theoretically, if we see an uninterrupted error stream, we will remain
in storm mode indefinitely and keep polling the MSRs.
However, when the storm is actually a burst of errors, once we have
logged them all, we back out of it after ~5 mins of polling and no more
errors logged.
If we encounter an error during those 5 minutes, we reset the polling
interval to 5 mins.
Making machine_check_poll() return a bool and denoting whether it has
seen an error or not lets us simplify a bunch of code and move the storm
handling private to mce_intel.c.
Some minor cleanups while at it.
Reported-by: Calvin Owens <calvinowens@fb.com>
Tested-by: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/1417746575-23299-1-git-send-email-calvinowens@fb.com
Signed-off-by: Borislav Petkov <bp@suse.de>
|
|
__get_cpu_var() is used for multiple purposes in the kernel source. One of
them is address calculation via the form &__get_cpu_var(x). This calculates
the address for the instance of the percpu variable of the current processor
based on an offset.
Other use cases are for storing and retrieving data from the current
processors percpu area. __get_cpu_var() can be used as an lvalue when
writing data or on the right side of an assignment.
__get_cpu_var() is defined as :
#define __get_cpu_var(var) (*this_cpu_ptr(&(var)))
__get_cpu_var() always only does an address determination. However, store
and retrieve operations could use a segment prefix (or global register on
other platforms) to avoid the address calculation.
this_cpu_write() and this_cpu_read() can directly take an offset into a
percpu area and use optimized assembly code to read and write per cpu
variables.
This patch converts __get_cpu_var into either an explicit address
calculation using this_cpu_ptr() or into a use of this_cpu operations that
use the offset. Thereby address calculations are avoided and less registers
are used when code is generated.
Transformations done to __get_cpu_var()
1. Determine the address of the percpu instance of the current processor.
DEFINE_PER_CPU(int, y);
int *x = &__get_cpu_var(y);
Converts to
int *x = this_cpu_ptr(&y);
2. Same as #1 but this time an array structure is involved.
DEFINE_PER_CPU(int, y[20]);
int *x = __get_cpu_var(y);
Converts to
int *x = this_cpu_ptr(y);
3. Retrieve the content of the current processors instance of a per cpu
variable.
DEFINE_PER_CPU(int, y);
int x = __get_cpu_var(y)
Converts to
int x = __this_cpu_read(y);
4. Retrieve the content of a percpu struct
DEFINE_PER_CPU(struct mystruct, y);
struct mystruct x = __get_cpu_var(y);
Converts to
memcpy(&x, this_cpu_ptr(&y), sizeof(x));
5. Assignment to a per cpu variable
DEFINE_PER_CPU(int, y)
__get_cpu_var(y) = x;
Converts to
__this_cpu_write(y, x);
6. Increment/Decrement etc of a per cpu variable
DEFINE_PER_CPU(int, y);
__get_cpu_var(y)++
Converts to
__this_cpu_inc(y)
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86@kernel.org
Acked-by: H. Peter Anvin <hpa@linux.intel.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Commit ea431643d6c3 ("x86/mce: Fix CMCI preemption bugs") breaks RT by
the completely unrelated conversion of the cmci_discover_lock to a
regular (non raw) spinlock. This lock was annotated in commit
59d958d2c7de ("locking, x86: mce: Annotate cmci_discover_lock as raw")
with a proper explanation why.
The argument for converting the lock back to a regular spinlock was:
- it does percpu ops without disabling preemption. Preemption is not
disabled due to the mistaken use of a raw spinlock.
Which is complete nonsense. The raw_spinlock is disabling preemption in
the same way as a regular spinlock. In mainline spinlock maps to
raw_spinlock, in RT spinlock becomes a "sleeping" lock.
raw_spinlock has on RT exactly the same semantics as in mainline. And
because this lock is taken in non preemptible context it must be raw on
RT.
Undo the locking brainfart.
Reported-by: Clark Williams <williams@redhat.com>
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The following commit:
27f6c573e0f7 ("x86, CMCI: Add proper detection of end of CMCI storms")
Added two preemption bugs:
- machine_check_poll() does a get_cpu_var() without a matching
put_cpu_var(), which causes preemption imbalance and crashes upon
bootup.
- it does percpu ops without disabling preemption. Preemption is not
disabled due to the mistaken use of a raw spinlock.
To fix these bugs fix the imbalance and change
cmci_discover_lock to a regular spinlock.
Reported-by: Owen Kibel <qmewlo@gmail.com>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Chen, Gong <gong.chen@linux.intel.com>
Cc: Josh Boyer <jwboyer@fedoraproject.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Alexander Todorov <atodorov@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/n/tip-jtjptvgigpfkpvtQxpEk1at2@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
--
arch/x86/kernel/cpu/mcheck/mce.c | 4 +---
arch/x86/kernel/cpu/mcheck/mce_intel.c | 18 +++++++++---------
2 files changed, 10 insertions(+), 12 deletions(-)
|
|
When CMCI storm persists for a long time(at least beyond predefined
threshold. It's 30 seconds for now), we can watch CMCI storm is
detected immediately after it subsides.
...
Dec 10 22:04:29 kernel: CMCI storm detected: switching to poll mode
Dec 10 22:04:59 kernel: CMCI storm subsided: switching to interrupt mode
Dec 10 22:04:59 kernel: CMCI storm detected: switching to poll mode
Dec 10 22:05:29 kernel: CMCI storm subsided: switching to interrupt mode
...
The problem is that our logic that determines that the storm has
ended is incorrect. We announce the end, re-enable interrupts and
realize that the storm is still going on, so we switch back to
polling mode. Rinse, repeat.
When a storm happens we disable signaling of errors via CMCI and begin
polling machine check banks instead. If we find any logged errors,
then we need to set a per-cpu flag so that our per-cpu tests that
check whether the storm is ongoing will see that errors are still
being logged independently of whether mce_notify_irq() says that the
error has been fully processed.
cmci_clear() is not the right tool to disable a bank. It disables the
interrupt for the bank as desired, but it also clears the bit for
this bank in "mce_banks_owned" so we will skip the bank when polling
(so we fail to see that the storm continues because we stop looking).
New cmci_storm_disable_banks() just disables the interrupt while
allowing polling to continue.
Reported-by: William Dauchy <wdauchy@gmail.com>
Signed-off-by: Chen, Gong <gong.chen@linux.intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
[ hpa: undid incorrect removal from arch/x86/kernel/head_32.S ]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Link: http://lkml.kernel.org/r/1389054026-12947-1-git-send-email-paul.gortmaker@windriver.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Pursue a single RAS/MCE topic branch on x86.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The Corrected Machine Check structure (CMC) in HEST has a flag which can be
set by the firmware to indicate to the OS that it prefers to process the
corrected error events first. In this scenario, the OS is expected to not
monitor for corrected errors (through CMCI/polling). Instead, the firmware
notifies the OS on corrected error events through GHES.
Linux already has support for GHES. This patch adds support for parsing CMC
structure and to disable CMCI/polling if the firmware first flag is set.
Further, the list of machine check bank structures at the end of CMC is used
to determine which MCA banks function in FF mode, so that we continue to
monitor error events on the other banks.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
the MCA subsystem
There is some confusion about the 'mce_poll_banks' and 'mce_banks_owned'
per-cpu bitmaps. Provide comments so that we all know exactly what these
are used for, and why.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
Dave Jones reports that offlining a CPU leads to this trace:
numa_remove_cpu cpu 1 node 0: mask now 0,2-3
smpboot: CPU 1 is now offline
BUG: using smp_processor_id() in preemptible [00000000] code:
cpu-offline.sh/10591
caller is cmci_rediscover+0x6a/0xe0
Pid: 10591, comm: cpu-offline.sh Not tainted 3.9.0-rc3+ #2
Call Trace:
[<ffffffff81333bbd>] debug_smp_processor_id+0xdd/0x100
[<ffffffff8101edba>] cmci_rediscover+0x6a/0xe0
[<ffffffff815f5b9f>] mce_cpu_callback+0x19d/0x1ae
[<ffffffff8160ea66>] notifier_call_chain+0x66/0x150
[<ffffffff8107ad7e>] __raw_notifier_call_chain+0xe/0x10
[<ffffffff8104c2e3>] cpu_notify+0x23/0x50
[<ffffffff8104c31e>] cpu_notify_nofail+0xe/0x20
[<ffffffff815ef082>] _cpu_down+0x302/0x350
[<ffffffff815ef106>] cpu_down+0x36/0x50
[<ffffffff815f1c9d>] store_online+0x8d/0xd0
[<ffffffff813edc48>] dev_attr_store+0x18/0x30
[<ffffffff81226eeb>] sysfs_write_file+0xdb/0x150
[<ffffffff811adfb2>] vfs_write+0xa2/0x170
[<ffffffff811ae16c>] sys_write+0x4c/0xa0
[<ffffffff81613019>] system_call_fastpath+0x16/0x1b
However, a look at cmci_rediscover shows that it can be simplified quite
a bit, apart from solving the above issue. It invokes functions that
take spin locks with interrupts disabled, and hence it can run in atomic
context. Also, it is run in the CPU_POST_DEAD phase, so the dying CPU
is already dead and out of the cpu_online_mask. So take these points into
account and simplify the code, and thereby also fix the above issue.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 RAS update from Ingo Molnar:
"Rework all config variables used throughout the MCA code and collect
them together into a mca_config struct. This keeps them tightly and
neatly packed together instead of spilled all over the place.
Then, convert those which are used as booleans into real booleans and
save some space. These bits are exposed via
/sys/devices/system/machinecheck/machinecheck*/"
* 'x86-ras-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, MCA: Finish mca_config conversion
x86, MCA: Convert the next three variables batch
x86, MCA: Convert rip_msr, mce_bootlog, monarch_timeout
x86, MCA: Convert dont_log_ce, banks and tolerant
drivers/base: Add a DEVICE_BOOL_ATTR macro
|
|
cmci_rediscover() used set_cpus_allowed_ptr() to change the current process's
running cpu, and migrate itself to the dest cpu. But worker processes are not
allowed to be migrated. If current is a worker, the worker will be migrated to
another cpu, but the corresponding worker_pool is still on the original cpu.
In this case, the following BUG_ON in try_to_wake_up_local() will be triggered:
BUG_ON(rq != this_rq());
This will cause the kernel panic. The call trace is like the following:
[ 6155.451107] ------------[ cut here ]------------
[ 6155.452019] kernel BUG at kernel/sched/core.c:1654!
......
[ 6155.452019] RIP: 0010:[<ffffffff810add15>] [<ffffffff810add15>] try_to_wake_up_local+0x115/0x130
......
[ 6155.452019] Call Trace:
[ 6155.452019] [<ffffffff8166fc14>] __schedule+0x764/0x880
[ 6155.452019] [<ffffffff81670059>] schedule+0x29/0x70
[ 6155.452019] [<ffffffff8166de65>] schedule_timeout+0x235/0x2d0
[ 6155.452019] [<ffffffff810db57d>] ? mark_held_locks+0x8d/0x140
[ 6155.452019] [<ffffffff810dd463>] ? __lock_release+0x133/0x1a0
[ 6155.452019] [<ffffffff81671c50>] ? _raw_spin_unlock_irq+0x30/0x50
[ 6155.452019] [<ffffffff810db8f5>] ? trace_hardirqs_on_caller+0x105/0x190
[ 6155.452019] [<ffffffff8166fefb>] wait_for_common+0x12b/0x180
[ 6155.452019] [<ffffffff810b0b30>] ? try_to_wake_up+0x2f0/0x2f0
[ 6155.452019] [<ffffffff8167002d>] wait_for_completion+0x1d/0x20
[ 6155.452019] [<ffffffff8110008a>] stop_one_cpu+0x8a/0xc0
[ 6155.452019] [<ffffffff810abd40>] ? __migrate_task+0x1a0/0x1a0
[ 6155.452019] [<ffffffff810a6ab8>] ? complete+0x28/0x60
[ 6155.452019] [<ffffffff810b0fd8>] set_cpus_allowed_ptr+0x128/0x130
[ 6155.452019] [<ffffffff81036785>] cmci_rediscover+0xf5/0x140
[ 6155.452019] [<ffffffff816643c0>] mce_cpu_callback+0x18d/0x19d
[ 6155.452019] [<ffffffff81676187>] notifier_call_chain+0x67/0x150
[ 6155.452019] [<ffffffff810a03de>] __raw_notifier_call_chain+0xe/0x10
[ 6155.452019] [<ffffffff81070470>] __cpu_notify+0x20/0x40
[ 6155.452019] [<ffffffff810704a5>] cpu_notify_nofail+0x15/0x30
[ 6155.452019] [<ffffffff81655182>] _cpu_down+0x262/0x2e0
[ 6155.452019] [<ffffffff81655236>] cpu_down+0x36/0x50
[ 6155.452019] [<ffffffff813d3eaa>] acpi_processor_remove+0x50/0x11e
[ 6155.452019] [<ffffffff813a6978>] acpi_device_remove+0x90/0xb2
[ 6155.452019] [<ffffffff8143cbec>] __device_release_driver+0x7c/0xf0
[ 6155.452019] [<ffffffff8143cd6f>] device_release_driver+0x2f/0x50
[ 6155.452019] [<ffffffff813a7870>] acpi_bus_remove+0x32/0x6d
[ 6155.452019] [<ffffffff813a7932>] acpi_bus_trim+0x87/0xee
[ 6155.452019] [<ffffffff813a7a21>] acpi_bus_hot_remove_device+0x88/0x16b
[ 6155.452019] [<ffffffff813a33ee>] acpi_os_execute_deferred+0x27/0x34
[ 6155.452019] [<ffffffff81090589>] process_one_work+0x219/0x680
[ 6155.452019] [<ffffffff81090528>] ? process_one_work+0x1b8/0x680
[ 6155.452019] [<ffffffff813a33c7>] ? acpi_os_wait_events_complete+0x23/0x23
[ 6155.452019] [<ffffffff810923be>] worker_thread+0x12e/0x320
[ 6155.452019] [<ffffffff81092290>] ? manage_workers+0x110/0x110
[ 6155.452019] [<ffffffff81098396>] kthread+0xc6/0xd0
[ 6155.452019] [<ffffffff8167c4c4>] kernel_thread_helper+0x4/0x10
[ 6155.452019] [<ffffffff81671f30>] ? retint_restore_args+0x13/0x13
[ 6155.452019] [<ffffffff810982d0>] ? __init_kthread_worker+0x70/0x70
[ 6155.452019] [<ffffffff8167c4c0>] ? gs_change+0x13/0x13
This patch removes the set_cpus_allowed_ptr() call, and put the cmci rediscover
jobs onto all the other cpus using system_wq. This could bring some delay for
the jobs.
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
mce_ser, mce_bios_cmci_threshold and mce_disabled are the last three
bools which need conversion. Move them to the mca_config struct and
adjust usage sites accordingly.
Signed-off-by: Borislav Petkov <bp@alien8.de>
Acked-by: Tony Luck <tony.luck@intel.com>
|
|
Move them into the mca_config struct and adjust code touching them
accordingly.
Signed-off-by: Borislav Petkov <bp@alien8.de>
Acked-by: Tony Luck <tony.luck@intel.com>
|
|
The ACPI spec doesn't provide for a way for the bios to pass down
recommended thresholds to the OS on a _per-bank_ basis. This patch adds
a new boot option, which if passed, tells Linux to use CMCI thresholds
set by the bios.
As fail-safe, we initialize threshold to 1 if some banks have not been
initialized by the bios and warn the user.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
On Intel systems corrected machine check interrupts (CMCI) may be sent to
multiple logical processors; possibly to all processors on the affected
socket (SDM Volume 3B "15.5.1 CMCI Local APIC Interface"). This means
that a persistent error (such as a stuck bit in ECC memory) may cause
a storm of interrupts that greatly hinders or prevents forward progress
(probably on many processors).
To solve this we keep track of the rate at which each processor sees
CMCI. If we exceed a threshold, we disable CMCI delivery and switch to
polling the machine check banks. If the storm subsides (none of the
affected processors see any more errors for a complete poll interval) we
re-enable CMCI.
[Tony: Added console messages when storm begins/ends and increased storm
threshold from 5 to 15 so we have a few more logged entries before we
disable interrupts and start dropping reports]
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
cmci_discover() works out which machine check banks support CMCI, and
which of those are shared by multiple logical processors. It uses this
information to ensure that exactly one cpu is designated the owner of
each bank so that when interrupts are broadcast to multiple cpus, only one
of them will look in a shared bank to log the error and clear the bank.
At boot time cmci_discover() performs this task silently. But during
certain cpu hotplug operations it prints out a set of summary lines
like this:
CPU 35 MCA banks CMCI:0 CMCI:1 CMCI:3 CMCI:5 CMCI:6 CMCI:7 CMCI:8 CMCI:9 CMCI:10 CMCI:11
CPU 1 MCA banks CMCI:0 CMCI:1 CMCI:3
CPU 39 MCA banks CMCI:0 CMCI:1 CMCI:3
CPU 38 MCA banks CMCI:0 CMCI:1 CMCI:3
CPU 32 MCA banks CMCI:0 CMCI:1 CMCI:3
CPU 37 MCA banks CMCI:0 CMCI:1 CMCI:3
CPU 36 MCA banks CMCI:0 CMCI:1 CMCI:3
CPU 34 MCA banks CMCI:0 CMCI:1 CMCI:3
The value of these messages seems very low. A user might painstakingly
cross-check against the data sheet for a processor to ensure that all
CMCI supported banks are correctly reported, but this seems improbable.
If users really wanted to do this, we should print the information at
boot time too.
Remove the messages.
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
The cmci_discover_lock can be taken in atomic context (cpu bring
up sequence) and therefore cannot be preempted on -rt.
In mainline this change documents the low level nature of
the lock - otherwise there's no functional difference. Lockdep
and Sparse checking will work as usual.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Replace all uses of current_cpu_data with this_cpu operations on the
per cpu structure cpu_info. The scala accesses are replaced with the
matching this_cpu ops which results in smaller and more efficient
code.
In the long run, it might be a good idea to remove cpu_data() macro
too and use per_cpu macro directly.
tj: updated description
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
It is reported that CMCI is not raised when number of corrected error
reaches preset threshold. After inspection, it is found that
MSR_IA32_MCI_CTL2 threshold field is not setup properly. This patch
fixed it.
Value of MCI_CTL2_CMCI_THRESHOLD_MASK is fixed according to x86_64
Software Developer's Manual too.
Reported-by: Shaohui Zheng <shaohui.zheng@intel.com>
Signed-off-by: Huang Ying <ying.huang@intel.com>
LKML-Reference: <1275977350.3444.660.camel@yhuang-dev.sh.intel.com>
Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Rename CMCI_EN to MCI_CTL2_CMCI_EN and CMCI_THRESHOLD_MASK to
MCI_CTL2_CMCI_THRESHOLD_MASK to make naming consistent.
Signed-off-by: Huang Ying <ying.huang@intel.com>
LKML-Reference: <1275977348.3444.659.camel@yhuang-dev.sh.intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
|
|
Don't write per cpu MCA boot up messages.
Signed-of-by: Mike Travis <travis@sgi.com>
Cc: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: x86@kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
|
|
Instead of open coded calculations for bank MSRs hide the indexing of higher
banks MCE register MSRs in new macros.
No semantic changes.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
mce_intel.c uses apic_write() and lapic_get_maxlvt(), and so it needs
<asm/apic.h>.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
|
|
Rename files that are no longer 64bit specific:
mce_amd_64.c => mce_amd.c
mce_intel_64.c => mce_intel.c
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
move intel_init_thermal() into therm_throt.c
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
There are 2 headers:
arch/x86/include/asm/mce.h
arch/x86/kernel/cpu/mcheck/mce.h
and in the latter small header:
#include <asm/mce.h>
This patch move all contents in the latter header into the former,
and fix all files using the latter to include the former instead.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Decode magic constants and turn them into symbols.
[ Cleanup to use symbols already exists - HS ]
[ Impact: cleanup ]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Mechanic unification. No change in code.
[ Impact: cleanup, 32-bit / 64-bit unification ]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
