| Age | Commit message (Collapse) | Author |
|---|
|
Enable the SLPI DSP on the Oneplus 6 phone with a Qualcomm SDM845 SoC.
Signed-off-by: Dylan Van Assche <me@dylanvanassche.be>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230406173148.28309-5-me@dylanvanassche.be
|
|
Qualcomm SDM845 SoC features a SLPI DSP which uses FastRPC through
an allocated memory region to load files from the host filesystem
such as sensor configuration files.
Add a FastRPC node at /dev/fastrpc-sdsp and a DMA region, similar to
downstream, to allow userspace to communicate with the SLPI via the
FastRPC interface for initializing the sensors on the SLPI.
Signed-off-by: Dylan Van Assche <me@dylanvanassche.be>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230406173148.28309-4-me@dylanvanassche.be
|
|
Add the SLPI remoteproc to the SDM845 Qualcomm SoC which is responsible
for exposing the sensors connected to the SoC. The SLPI communicates
over GLink edge 'dsps' and is similar to other DSPs e.g. ADSP or CDSP.
This patch allows the SLPI to boot and expose itself over QRTR as
service 400.
Signed-off-by: Dylan Van Assche <me@dylanvanassche.be>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230406173148.28309-2-me@dylanvanassche.be
|
|
Add PMIC regulators for sa8775p-ride.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230406192811.460888-4-brgl@bgdev.pl
|
|
Drop the unnecessary mux{} level to make dtbs check happy.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407-topic-msm_dtb-v1-6-6efb4196f51f@linaro.org
|
|
Fix the node name to make dtbs_check happy:
qcom/apq8016-sbc.dtb: pmic@0: 'extcon@1300' does not match any of the
regexes: '(.*)?(wled|leds)@[0-9a-f]+$', '^adc-tm@[0-9a-f]+$',
'^adc@[0-9a-f]+$', '^audio-codec@[0-9a-f]+$', '^charger@[0-9a-f]+$',
'^mpps@[0-9a-f]+$', '^nvram@[0-9a-f]+$', '^rtc@[0-9a-f]+$',
'^temp-alarm@[0-9a-f]+$', '^usb-detect@[0-9a-f]+$',
'^usb-vbus-regulator@[0-9a-f]+$', '^vibrator@[0-9a-f]+$',
'gpio@[0-9a-f]+$', 'pinctrl-[0-9]+', 'pon@[0-9a-f]+$'
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407-topic-msm_dtb-v1-5-6efb4196f51f@linaro.org
|
|
Fix the following schema warning:
gic-its@17a40000: False schema does not allow {'compatible':
['arm,gic-v3-its'], 'msi-controller': True, '#msi-cells': [[1]],
'reg': [[0, 396623872, 0, 131072]], 'status': ['disabled']}
And reorder the properties to be more in order with all other nodes.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407-topic-msm_dtb-v1-4-6efb4196f51f@linaro.org
|
|
Cheza's SPI flash hookups (qspi) are exactly the same as trogdor's.
Apply the same solution that's described in the patch ("arm64: dts:
qcom: sc7180: Fix trogdor qspi pin config")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323102605.14.I82951106ab8170f973a4c1c7d9b034655bbe2f60@changeid
|
|
Similar to sc7180 (see the patch ("arm64: dts: qcom: sc7180: Fix
trogdor qspi pin config")), we should adjust the qspi pin config for
sc7280.
I won't re-describe all the research/arguments in the sc7180 patch
here, but there are a few differences for sc7280 worth noting:
1. On herobrine the SPI flash (qspi) is wired up differently on the
board. Rather than Cr50 and the AP being wired directly together,
there's actually a mux that will _either_ connect the AP to the
flash or Cr50 to the flash. This means that the internal pulls on
Cr50 don't affect us and we should enable our own pulldowns.
2. On herobrine, EEs added an external pulldown on the MISO line. The
argument in the schematic said that we added it (but not one on
MOSI and CLK) because Cr50 already enabled pulldowns on MOSI and
CLK. ...though, as per #1, those Cr50 pulldowns would only affect
the line when the mux was swung to Cr50.
The ironic result of #1 and #2 is that the external pulldowns on
CLK/MISO/MOSI on herobrine are _exactly opposite_ of the ones on
trogdor.
3. While I still don't have the actual exact schematics for all
variants of IDP/CRD that were produced, I have some reference
schematics that give me a belief of how the qspi is hooked up
there. From this, I'm fairly certain that all of the older variants
of IDP/CRD either have a pulldown on the CLK/MOSI/MISO lines (maybe
through a direct connect to Cr50) or have no pull (in other words,
they don't have a pullup). I'll go ahead and enable internal
pulldowns on all the lines since that won't hurt to double-pull if
there's an external pulldown and it's nice to have a pulldown if
there's nothing external. Note that this only affects _older_
CRDs. Newer revs are considered "herobrine" (see the hoglin/zoglin
device trees).
4. I didn't find the same strange "auto-switch-to-keeper" at suspend
when probing on sc7280. Whatever pulls (or lack thereof) I left at
suspend time seemed to persist into suspend.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323102605.13.Ib44c3e417c414a4227db8def75ded37ad368212c@changeid
|
|
In commit 7ec3e67307f8 ("arm64: dts: qcom: sc7180-trogdor: add initial
trogdor and lazor dt") we specified the pull settings on the boot SPI
(the qspi) data lines as pullups to "park" the lines. This seemed like
the right thing to do, but I never really probed the lines to confirm.
Since that time, I've done A LOT of research, experiements and poking
of the lines with a voltmeter.
A first batch of discoveries:
- There is an external pullup on CS (clearly shown on schematics)
- There are weak external pulldowns on CLK/MOSI (believed to be Cr50's
internal pulldowns)
- There is no pull on MISO.
- When qspi isn't actively transferring it still drives CS, CLK, and
MOSI. CS and MOSI are driven high and CLK is driven low. It does not
drive MISO and (if no internal pulls are enabled) the line floats.
The above means that it's good to have some sort of pull on MISO, at
the very least. The pullup that we had before was actually fine (and
my voltmeter confirms that it actually affected the state of the pin)
but a pulldown would work equally well (and would match MOSI and CLK
better).
The above also means that we could save a tiny bit of power (not
measurable by my setup) by setting up a sleep state for these pins. If
nothing else this prevents us from driving high against Cr50's
internal pulldown on MOSI. However, Qualcomm has also asserted in the
past that it burns a little extra power to drive a pin, especially
since these are configured with a slightly higher drive strength
Let's fix all this. Since the external pulls are different for the two
data lines, we'll split them into separate configs. Then we'll change
the MISO pin to a pulldown and add a sleep state.
On a slightly tangental (but not totally unrelated note), I also
discovered some interesting things with these pins in suspend. First,
I found that if we don't switch the pins to GPIO that the qspi
peripheral continues to drive them in suspend. That'll be solved by
what we're already doing above. Second, I found that something in the
system suspend path (after Linux stops running) reconfigures these
pins so that they don't have their normal pulls enabled but instead
change to "keepers" (bias-bus-hold in DT speak). If a pin was floating
before we entered suspend then it would stop floating. I found that I
could manually pull a pin to a different level and then probe it and
it would stay there. This is exactly keeper behavior. With the
solution we have the switch to "keeper" doesn't matter too much but
it's good to document.
While talking about "keepers", it can also be noted that I found that
the "keepers" on these pins were at least enough to win a fight
against Cr50's internal pulls. That means it's best to make sure that
the state of the pins are already correct before the mysterious
transition to a keeper. Otherwise we'll burn (a small amount of) power
in S3 via this fight. Luckily with the current solution we don't hit
this case.
NOTE: I've left "sc7180-idp" behavior totally alone in this patch. I
didn't add a sleep state and I didn't change any pulls--I just adapted
it to the fact that the data lines have separate configs. Qualcomm
doesn't provide me with schematics for IDP and thus I don't actually
know how the pulls are configured. Since this is just a development
platform and worked well enough, it seems safer to leave it alone.
Dependencies:
- This patch has a hard dependency on ("pinctrl: qcom: Support
OUTPUT_ENABLE; deprecate INPUT_ENABLE"). Something in the boot code
seemed to have been confused and thought it needed to set the
"OUTPUT ENABLE" bit for these pins even though it was using them as
SPI. Thus if we don't honor the "output-disable" property we could
end up driving the SPI pins while in sleep mode.
- In general, it's probably best not to backport this to a kernel that
doesn't have commit d21f4b7ffc22 ("pinctrl: qcom: Avoid glitching
lines when we first mux to output"). That landed a while ago, but
it's still good to be explicit in case someone was backporting. If
we don't have that then there might be a glitch when we first switch
over to GPIO before we disable the output.
- This patch _doesn't_ really have any dependency on the qspi driver
patch that supports setting the pinctrl sleep state--they can go in
either order. If we define the sleep state and the driver never
selects it that's fine. If the driver tries to select a sleep state
that we don't define that's fine.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323102605.12.I6f03f86546e6ce9abb1d24fd9ece663c3a5b950c@changeid
|
|
As talked about in the patch ("dt-bindings: pinctrl: qcom: tlmm should
use output-disable, not input-enable"), using "input-enable" in
pinctrl states for Qualcomm TLMM pinctrl devices was either
superfluous or there to disable a pin's output.
Looking at cheza
* ec_ap_int_l, h1_ap_int_odl: Superfluous. The pins will be configured
as inputs automatically by the Linux GPIO subsystem (presumably the
reference for other OSes using these device trees).
* bios_flash_wp_l: Superfluous. This pin is exposed to userspace
through the kernel's GPIO API and will be configured automatically.
That means that in none of the cases for cheza did we need to change
"input-enable" to "output-disable" and we can just remove these
superfluous properties.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323102605.11.Ia439c29517b1c0625325a54387b047f099d16425@changeid
|
|
As talked about in the patch ("dt-bindings: pinctrl: qcom: tlmm should
use output-disable, not input-enable"), using "input-enable" in
pinctrl states for Qualcomm TLMM pinctrl devices was either
superfluous or there to disable a pin's output.
Looking at the sc7280-idp-ec-h1.dtsi file:
* ap_ec_int_l, h1_ap_int_odl: Superfluous. The pins will be configured
as inputs automatically by the Linux GPIO subsystem (presumably the
reference for other OSes using these device trees).
That means that in none of the cases for sc7280-idp-ec-h1.dtsi did we
need to change "input-enable" to "output-disable" and we can just
remove these superfluous properties.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323102605.10.I1343c20f4aaac8e2c1918b756f7ed66f6ceace9c@changeid
|
|
As talked about in the patch ("dt-bindings: pinctrl: qcom: tlmm should
use output-disable, not input-enable"), using "input-enable" in
pinctrl states for Qualcomm TLMM pinctrl devices was either
superfluous or there to disable a pin's output.
Looking at trogdor:
* ap_ec_int_l, fp_to_ap_irq_l, h1_ap_int_odl, p_sensor_int_l:
Superfluous. The pins will be configured as inputs automatically by
the Linux GPIO subsystem (presumably the reference for other OSes
using these device trees).
* bios_flash_wp_l: Superfluous. This pin is exposed to userspace
through the kernel's GPIO API and will be configured automatically.
That means that in none of the cases for trogdor did we need to change
"input-enable" to "output-disable" and we can just remove these
superfluous properties.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323102605.9.I94dbc53176e8adb0d7673b7feb2368e85418f938@changeid
|
|
The l13a rail on trogdor devices has always been intended to be
always-on on both S0 and S3. Different trogdor variants use l13a in
slightly different ways, but the overall theme is that it's a 1.8V
rail that the board uses for things that it wants powered in on S0 and
S3. On many boards this includes the boot SPI (AKA qspi).
For all intents and purposes this patch is actually a no-op since
something else in the system seems to already be keeping the rail on
all the time (confirmed via multimeter). That "something else" was
postulated to be the modem but the rail is on / stays on even without
the modem/wifi coming up so it's likely the boot config. In any case,
making the fact that this is always-on explicit seems like a good
idea.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323102605.4.I9f47a8a53eacff6229711a827993792ceeb36971@changeid
|
|
There are 4 qspi data pins: data0, data1, data2, and data3. Currently
we have a shared pin state for data0 and data1 (2 lane config) and a
pin state for data2 and data3 (you'd enable both this and the 2 lane
state for 4 lanes). The second state is obviously misnamed. Fix it.
Fixes: e1ce853932b7 ("arm64: dts: qcom: sdm845: Add qspi (quad SPI) node")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323102605.3.I88528d037b7fda4e53a40f661be5ac61628691cd@changeid
|
|
There are 4 qspi data pins: data0, data1, data2, and data3. Currently
we have a shared pin state for data0 and data1 (2 lane config) and a
pin state for data2 and data3 (you'd enable both this and the 2 lane
state for 4 lanes). The second state is obviously misnamed. Fix it.
Fixes: 7720ea001b52 ("arm64: dts: qcom: sc7280: Add QSPI node")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323102605.2.I4043491bb24b1e92267c5033d76cdb0fe60934da@changeid
|
|
There are 4 qspi data pins: data0, data1, data2, and data3. Currently
we have a shared pin state for data0 and data1 (2 lane config) and a
pin state for data2 and data3 (you'd enable both this and the 2 lane
state for 4 lanes). The second state is obviously misnamed. Fix it.
Fixes: ba3fc6496366 ("arm64: dts: sc7180: Add qupv3_0 and qupv3_1")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323102605.1.Ifc1b5be04653f4ab119698a5944bfecded2080d6@changeid
|
|
Add initial device tree support for Qualcomm IPQ9574 SoC and AL02 board
Co-developed-by: Anusha Rao <quic_anusha@quicinc.com>
Signed-off-by: Anusha Rao <quic_anusha@quicinc.com>
Co-developed-by: Poovendhan Selvaraj <quic_poovendh@quicinc.com>
Signed-off-by: Poovendhan Selvaraj <quic_poovendh@quicinc.com>
Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230316072940.29137-6-quic_devipriy@quicinc.com
|
|
Enables clk & pinctrl related configs for Qualcomm IPQ9574 SoC
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230316072940.29137-7-quic_devipriy@quicinc.com
|
|
This fixes memory overlap error:
[ 0.000000] reserved@6300000 (0x0000000006300000--0x0000000007000000) overlaps with smem_region@6a00000 (0x0000000006a00000--0x0000000006c00000)
smem_region is the same as in downstream (qcom,smem) [1], therefore
split reserved memory into two sections on either side of smem_region.
Not adding labels as it's not expected to be used.
[1] https://android.googlesource.com/kernel/msm/+/refs/heads/android-msm-angler-3.10-marshmallow-mr1/arch/arm/boot/dts/qcom/msm8994.dtsi#948
Fixes: 380cd3a34b7f ("arm64: dts: msm8994-angler: fix the memory map")
Signed-off-by: Petr Vorel <pvorel@suse.cz>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230131200414.24373-3-pvorel@suse.cz
|
|
Angler's cont_splash_mem mapping is shorter in downstream [1],
therefore 380cd3a34b7f was wrong. Obviously also 0e5ded926f2a was wrong
(workaround which fixed booting at the time).
This fixes error:
[ 0.000000] memory@3401000 (0x0000000003401000--0x0000000005601000) overlaps with tzapp@4800000 (0x0000000004800000--0x0000000006100000)
[1] https://android.googlesource.com/kernel/msm/+/refs/heads/android-msm-angler-3.10-marshmallow-mr1/arch/arm64/boot/dts/huawei/huawei_msm8994_angler_row_vn1/huawei-fingerprint.dtsi#16
Fixes: 380cd3a34b7f ("arm64: dts: msm8994-angler: fix the memory map")
Fixes: 0e5ded926f2a ("arm64: dts: qcom: msm8994-angler: Disable cont_splash_mem")
Signed-off-by: Petr Vorel <pvorel@suse.cz>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230131200414.24373-2-pvorel@suse.cz
|
|
There are some interop issues seen across a few DP monitors with
HBR3 and herobrine boards where the DP display stays blank with hbr3.
This is still under investigation but in preparation for supporting
higher resolutions, its better to disable HBR3 till the issues are
root-caused as there is really no guarantee which monitors will show
the issue and which would not.
This can be enabled back after successful validation across more DP
sinks.
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230329233416.27152-1-quic_abhinavk@quicinc.com
|
|
When counting "Instructions Retired" (0xc0) in a guest, KVM will
occasionally increment the PMU counter regardless of if that event is
being filtered. This is because some PMU events are incremented via
kvm_pmu_trigger_event(), which doesn't know about the event filter. Add
the event filter to kvm_pmu_trigger_event(), so events that are
disallowed do not increment their counters.
Fixes: 9cd803d496e7 ("KVM: x86: Update vPMCs when retiring instructions")
Signed-off-by: Aaron Lewis <aaronlewis@google.com>
Reviewed-by: Like Xu <likexu@tencent.com>
Link: https://lore.kernel.org/r/20230307141400.1486314-2-aaronlewis@google.com
[sean: prepend "pmc" to the new function]
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Fix a "reprogam" => "reprogram" typo in kvm_pmu_request_counter_reprogam().
Fixes: 68fb4757e867 ("KVM: x86/pmu: Defer reprogram_counter() to kvm_pmu_handle_event()")
Signed-off-by: Like Xu <likexu@tencent.com>
Link: https://lore.kernel.org/r/20230310113349.31799-1-likexu@tencent.com
[sean: trim the changelog]
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
The DSA framework has got more picky about always having a phy-mode
for the CPU port. The SoC Ethernet is being configured to
10gbase-r. Set the switch phy-mode based on this. Additionally, the
SoC Ethernet is using in-band signalling to determine the link speed,
so add same parameter to the switch.
Additionally, the cpu label has never actually been used in the
binding, so remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The DSA framework has got more picky about always having a phy-mode
for the CPU port. The Armada Ethernet supports RGMII, SGMII,
1000base-x and 2500Base-X. Set the switch phy-mode based on how the
SoC Ethernet ports is been configured. For RGMII mode, have the switch
add the delays.
Additionally, the cpu label has never actually been used in the
binding, so remove it.
Lastly, add a fixed-link node indicating the expected speed/duplex of
the link to the SoC.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The DSA framework has got more picky about always having a phy-mode
for the CPU port. The Orion5x Ethernet is an RGMII port. Set the
switch to impose the RGMII delays.
Additionally, the cpu label has never actually been used in the
binding, so remove it.
Lastly, add a fixed-link node indicating the expected speed/duplex of
the link to the SoC.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The DSA framework has got more picky about always having a phy-mode
for the CPU port. The Kirkwood Ethernet is an RGMII port. Set the
switch to impose the RGMII delays.
Additionally, the cpu label has never actually been used in the
binding, so remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The GL-MV1000 (Brume) is a small form-factor gateway router.
It is based on the Marvell Armada 88F3720 SOC (1GHz), has 3 gigabit ethernet ports, 1 GB RAM, 16M SPI flash, 8GB eMMC and an uSD slot, as well as an USB 2.0 type A and an USB 3.0 type C port.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
CC: Pali <pali@kernel.org>
Reviewed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Bindings expect thermal node names to end with '-thermal':
armada-8040-db.dtb: thermal-zones: 'ap-thermal-cpu0', ... do not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-]{1,12}-thermal$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Armada 7040 uses a rather small 15MB memory window for every PCI adapter,
however this is not sufficient for Qualcomm QCA6390 802.11ax cards that
are shipped along with the OpenWrt WLAN model of MOCHAbin as ath11k
requires at least 16MB of memory.
So, similar to what MACCHIATOBin has been doing for years, lets move
to using the second PCIe 2 memory window and expand it to 128MB to
make it future proof.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The detection of atomic update failure in reserve_eilvt_offset() is
not correct. The value returned by atomic_cmpxchg() should be compared
to the old value from the location to be updated.
If these two are the same, then atomic update succeeded and
"eilvt_offsets[offset]" location is updated to "new" in an atomic way.
Otherwise, the atomic update failed and it should be retried with the
value from "eilvt_offsets[offset]" - exactly what atomic_try_cmpxchg()
does in a correct and more optimal way.
Fixes: a68c439b1966c ("apic, x86: Check if EILVT APIC registers are available (AMD only)")
Signed-off-by: Uros Bizjak <ubizjak@gmail.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20230227160917.107820-1-ubizjak@gmail.com
|
|
As for now all arches have dma_default_coherent reflecting default
DMA coherency for of devices, so there is no need to have a standalone
config option.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
A valid pmc is always tested before using pmu->reprogram_pmi. Eliminate
this part of the redundancy by setting the counter's bitmask directly,
and in addition, trigger KVM_REQ_PMU only once to save more cpu cycles.
Signed-off-by: Like Xu <likexu@tencent.com>
Link: https://lore.kernel.org/r/20230214050757.9623-4-likexu@tencent.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Invert the flows in intel_pmu_{g,s}et_msr()'s case statements so that
they follow the kernel's preferred style of:
if (<not valid>)
return <error>
<commit change>
return <success>
which is also the style used by every other {g,s}et_msr() helper (except
AMD's PMU variant, which doesn't use a switch statement).
Modify the "set" paths with costly side effects, i.e. that reprogram
counters, to skip only the side effects, i.e. to perform reserved bits
checks even if the value is unchanged. None of the reserved bits checks
are expensive, so there's no strong justification for skipping them, and
guarding only the side effect makes it slightly more obvious what is being
skipped and why.
No functional change intended (assuming no reserved bit bugs).
Link: https://lkml.kernel.org/r/Y%2B6cfen%2FCpO3%2FdLO%40google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
The name of function pmc_is_enabled() is a bit misleading. A PMC can
be disabled either by PERF_CLOBAL_CTRL or by its corresponding EVTSEL.
Append global semantics to its name.
Suggested-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Like Xu <likexu@tencent.com>
Link: https://lore.kernel.org/r/20230214050757.9623-2-likexu@tencent.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Zero out the LBR capabilities during PMU refresh to avoid exposing LBRs
to the guest against userspace's wishes. If userspace modifies the
guest's CPUID model or invokes KVM_CAP_PMU_CAPABILITY to disable vPMU
after an initial KVM_SET_CPUID2, but before the first KVM_RUN, KVM will
retain the previous LBR info due to bailing before refreshing the LBR
descriptor.
Note, this is a very theoretical bug, there is no known use case where a
VMM would deliberately enable the vPMU via KVM_SET_CPUID2, and then later
disable the vPMU.
Link: https://lore.kernel.org/r/20230311004618.920745-9-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Now that KVM disallows changing feature MSRs, i.e. PERF_CAPABILITIES,
after running a vCPU, WARN and bug the VM if the PMU is refreshed after
the vCPU has run.
Note, KVM has disallowed CPUID updates after running a vCPU since commit
feb627e8d6f6 ("KVM: x86: Forbid KVM_SET_CPUID{,2} after KVM_RUN"), i.e.
PERF_CAPABILITIES was the only remaining way to trigger a PMU refresh
after KVM_RUN.
Cc: Like Xu <like.xu.linux@gmail.com>
Link: https://lore.kernel.org/r/20230311004618.920745-8-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Disallow writes to feature MSRs after KVM_RUN to prevent userspace from
changing the vCPU model after running the vCPU. Similar to guest CPUID,
KVM uses feature MSRs to configure intercepts, determine what operations
are/aren't allowed, etc. Changing the capabilities while the vCPU is
active will at best yield unpredictable guest behavior, and at worst
could be dangerous to KVM.
Allow writing the current value, e.g. so that userspace can blindly set
all MSRs when emulating RESET, and unconditionally allow writes to
MSR_IA32_UCODE_REV so that userspace can emulate patch loads.
Special case the VMX MSRs to keep the generic list small, i.e. so that
KVM can do a linear walk of the generic list without incurring meaningful
overhead.
Cc: Like Xu <like.xu.linux@gmail.com>
Cc: Yu Zhang <yu.c.zhang@linux.intel.com>
Reviewed-by: Xiaoyao Li <xiaoyao.li@intel.com>
Link: https://lore.kernel.org/r/20230311004618.920745-7-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Add VMX MSRs to the runtime list of feature MSRs by iterating over the
range of emulated MSRs instead of manually defining each MSR in the "all"
list. Using the range definition reduces the cost of emulating a new VMX
MSR, e.g. prevents forgetting to add an MSR to the list.
Extracting the VMX MSRs from the "all" list, which is a compile-time
constant, also shrinks the list to the point where the compiler can
heavily optimize code that iterates over the list.
No functional change intended.
Reviewed-by: Xiaoyao Li <xiaoyao.li@intel.com>
Link: https://lore.kernel.org/r/20230311004618.920745-5-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Add macros to track the range of VMX feature MSRs that are emulated by
KVM to reduce the maintenance cost of extending the set of emulated MSRs.
Note, KVM doesn't necessarily emulate all known/consumed VMX MSRs, e.g.
PROCBASED_CTLS3 is consumed by KVM to enable IPI virtualization, but is
not emulated as KVM doesn't emulate/virtualize IPI virtualization for
nested guests.
No functional change intended.
Reviewed-by: Xiaoyao Li <xiaoyao.li@intel.com>
Link: https://lore.kernel.org/r/20230311004618.920745-4-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Add a helper to query if a vCPU has run so that KVM doesn't have to open
code the check on last_vmentry_cpu being set to a magic value.
No functional change intended.
Suggested-by: Xiaoyao Li <xiaoyao.li@intel.com>
Cc: Like Xu <like.xu.linux@gmail.com>
Reviewed-by: Xiaoyao Li <xiaoyao.li@intel.com>
Link: https://lore.kernel.org/r/20230311004618.920745-3-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Rename kvm_init_msr_list() to kvm_init_msr_lists() to clarify that it
initializes multiple lists: MSRs to save, emulated MSRs, and feature MSRs.
No functional change intended.
Reviewed-by: Xiaoyao Li <xiaoyao.li@intel.com>
Link: https://lore.kernel.org/r/20230311004618.920745-2-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
The AMD [1022:15b8] USB controller loses some internal functional MSI-X
context when transitioning from D0 to D3hot. BIOS normally traps D0->D3hot
and D3hot->D0 transitions so it can save and restore that internal context,
but some firmware in the field can't do this because it fails to clear the
AMD_15B8_RCC_DEV2_EPF0_STRAP2 NO_SOFT_RESET bit.
Clear AMD_15B8_RCC_DEV2_EPF0_STRAP2 NO_SOFT_RESET bit before USB controller
initialization during boot.
Link: https://lore.kernel.org/linux-usb/Y%2Fz9GdHjPyF2rNG3@glanzmann.de/T/#u
Link: https://lore.kernel.org/r/20230329172859.699743-1-Basavaraj.Natikar@amd.com
Reported-by: Thomas Glanzmann <thomas@glanzmann.de>
Tested-by: Thomas Glanzmann <thomas@glanzmann.de>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Cc: stable@vger.kernel.org
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into arm/fixes
RISC-V Devicetree fixes for v6.3-final
A solitary fix here from Krzysztof for an invalid property that
should've probably been removed months ago, but was missed due to it
being in a dtb that doesn't build w/ defconfig.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-dt-fixes-for-v6.3-final' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
riscv: dts: canaan: drop invalid spi-max-frequency
Link: https://lore.kernel.org/r/20230406-negate-octagon-0fc2e47dbde5@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
arch_prctl(ARCH_FORCE_TAGGED_SVA) overrides the default and allows LAM
and SVA to co-exist in the process. It is expected by called by the
process when it knows what it is doing.
arch_prctl() operates on the current process, but the same code is
reachable from ptrace where it can be called on arbitrary task.
Make it strict and only allow to set MM_CONTEXT_FORCE_TAGGED_SVA for the
current process.
Fixes: 23e5d9ec2bab ("x86/mm/iommu/sva: Make LAM and SVA mutually exclusive")
Suggested-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Dmitry Vyukov <dvyukov@google.com>
Link: https://lore.kernel.org/all/20230403111020.3136-3-kirill.shutemov%40linux.intel.com
|
|
Normally, LAM and SVA are mutually exclusive. LAM enabling will fail if
SVA is already in use.
Correct error code for the failure. EINTR is nonsensical there.
Fixes: 23e5d9ec2bab ("x86/mm/iommu/sva: Make LAM and SVA mutually exclusive")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Dmitry Vyukov <dvyukov@google.com>
Link: https://lore.kernel.org/all/CACT4Y+YfqSMsZArhh25TESmG-U4jO5Hjphz87wKSnTiaw2Wrfw@mail.gmail.com
Link: https://lore.kernel.org/all/20230403111020.3136-2-kirill.shutemov%40linux.intel.com
|
|
Conflicts:
drivers/net/ethernet/google/gve/gve.h
3ce934558097 ("gve: Secure enough bytes in the first TX desc for all TCP pkts")
75eaae158b1b ("gve: Add XDP DROP and TX support for GQI-QPL format")
https://lore.kernel.org/all/20230406104927.45d176f5@canb.auug.org.au/
https://lore.kernel.org/all/c5872985-1a95-0bc8-9dcc-b6f23b439e9d@tessares.net/
Adjacent changes:
net/can/isotp.c
051737439eae ("can: isotp: fix race between isotp_sendsmg() and isotp_release()")
96d1c81e6a04 ("can: isotp: add module parameter for maximum pdu size")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add the nodes for QUP peripheral, PRNG and WDOG. While at it, enable the
I2C device for MI01.2 board.
Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230320104530.30411-3-quic_kathirav@quicinc.com
|
|
Add the Low Power Audio SubSystem (LPASS) / ADSP audio codec macros on
Qualcomm SM8550. The nodes are very similar to SM8450, except missing
NPL clock which is not exposed on SM8550 and should not be touched.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230310134925.514125-1-krzysztof.kozlowski@linaro.org
|
