| Age | Commit message (Collapse) | Author |
|---|
|
On my Dell XPS 13 9350 with firmware 1.4.4 and SGX on, if I boot
Fedora 24's grub2-efi off a hard disk, my first 1MB of RAM looks
like:
efi: mem00: [Runtime Data |RUN| | | | | | | |WB|WT|WC|UC] range=[0x0000000000000000-0x0000000000000fff] (0MB)
efi: mem01: [Boot Data | | | | | | | | |WB|WT|WC|UC] range=[0x0000000000001000-0x0000000000027fff] (0MB)
efi: mem02: [Loader Data | | | | | | | | |WB|WT|WC|UC] range=[0x0000000000028000-0x0000000000029fff] (0MB)
efi: mem03: [Reserved | | | | | | | | |WB|WT|WC|UC] range=[0x000000000002a000-0x000000000002bfff] (0MB)
efi: mem04: [Runtime Data |RUN| | | | | | | |WB|WT|WC|UC] range=[0x000000000002c000-0x000000000002cfff] (0MB)
efi: mem05: [Loader Data | | | | | | | | |WB|WT|WC|UC] range=[0x000000000002d000-0x000000000002dfff] (0MB)
efi: mem06: [Conventional Memory| | | | | | | | |WB|WT|WC|UC] range=[0x000000000002e000-0x0000000000057fff] (0MB)
efi: mem07: [Reserved | | | | | | | | |WB|WT|WC|UC] range=[0x0000000000058000-0x0000000000058fff] (0MB)
efi: mem08: [Conventional Memory| | | | | | | | |WB|WT|WC|UC] range=[0x0000000000059000-0x000000000009ffff] (0MB)
My EBDA is at 0x2c000, which blocks off everything from 0x2c000 and
up, and my trampoline is 0x6000 bytes (6 pages), so it doesn't fit
in the loader data range at 0x28000.
Without this patch, it panics due to a failure to allocate the
trampoline. With this patch, it works:
[ +0.001744] Base memory trampoline at [ffff880000001000] 1000 size 24576
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mario Limonciello <mario_limonciello@dell.com>
Cc: Matt Fleming <mfleming@suse.de>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/998c77b3bf709f3dfed85cb30701ed1a5d8a438b.1470821230.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
If reserve_real_mode() fails, panicing immediately means we're
doomed. Make it safe to try more than once to allocate the
trampoline:
- Degrade a failure from panic() to pr_info(). (If we make it to
setup_real_mode() without reserving the trampoline, we'll panic
them.)
- Factor out helpers so that platform code can supply a specific
address to try.
- Warn if reserve_real_mode() is called after we're done with the
memblock allocator. If that were to happen, we would behave
unpredictably.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mario Limonciello <mario_limonciello@dell.com>
Cc: Matt Fleming <mfleming@suse.de>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/876e383038f3e9971aa72fd20a4f5da05f9d193d.1470821230.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
There's no need to run setup_real_mode() as early as we run it.
Defer it to the same early_initcall that sets up the page
permissions for the real mode code.
This should be a code size reduction. More importantly, it give us
a longer window in which we can allocate the real mode trampoline.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mario Limonciello <mario_limonciello@dell.com>
Cc: Matt Fleming <mfleming@suse.de>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/fd62f0da4f79357695e9bf3e365623736b05f119.1470821230.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The initialization process for trampoline_cr4_features and
mmu_cr4_features was confusing. The intent is for mmu_cr4_features
and *trampoline_cr4_features to stay in sync, but
trampoline_cr4_features is NULL until setup_real_mode() runs. The
old code synchronized *trampoline_cr4_features *twice*, once in
setup_real_mode() and once in setup_arch(). It also initialized
mmu_cr4_features in setup_real_mode(), which causes the actual value
of mmu_cr4_features to potentially depend on when setup_real_mode()
is called.
With this patch, mmu_cr4_features is initialized directly in
setup_arch(), and *trampoline_cr4_features is synchronized to
mmu_cr4_features when the trampoline is set up.
After this patch, it should be safe to defer setup_real_mode().
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mario Limonciello <mario_limonciello@dell.com>
Cc: Matt Fleming <mfleming@suse.de>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/d48a263f9912389b957dd495a7127b009259ffe0.1470821230.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
reserve_bios_regions() is a quirk that reserves memory that we might
otherwise think is available. There's no need to run it so early,
and running it before we have the memory map initialized with its
non-quirky inputs makes it hard to make reserve_bios_regions() more
intelligent.
Move it right after we populate the memblock state.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mario Limonciello <mario_limonciello@dell.com>
Cc: Matt Fleming <mfleming@suse.de>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/59f58618911005c799c6c9979ce6ae4881d907c2.1470821230.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Since commit:
52aec3308db8 ("x86/tlb: replace INVALIDATE_TLB_VECTOR by CALL_FUNCTION_VECTOR")
the TLB remote shootdown is done through call function vector. That
commit didn't take care of irq_tlb_count, which a later commit:
fd0f5869724f ("x86: Distinguish TLB shootdown interrupts from other functions call interrupts")
... tried to fix.
The fix assumes every increase of irq_tlb_count has a corresponding
increase of irq_call_count. So the irq_call_count is always bigger than
irq_tlb_count and we could substract irq_tlb_count from irq_call_count.
Unfortunately this is not true for the smp_call_function_single() case.
The IPI is only sent if the target CPU's call_single_queue is empty when
adding a csd into it in generic_exec_single. That means if two threads
are both adding flush tlb csds to the same CPU's call_single_queue, only
one IPI is sent. In other words, the irq_call_count is incremented by 1
but irq_tlb_count is incremented by 2. Over time, irq_tlb_count will be
bigger than irq_call_count and the substract will produce a very large
irq_call_count value due to overflow.
Considering that:
1) it's not worth to send more IPIs for the sake of accurate counting of
irq_call_count in generic_exec_single();
2) it's not easy to tell if the call function interrupt is for TLB
shootdown in __smp_call_function_single_interrupt().
Not to exclude TLB shootdown from call function count seems to be the
simplest fix and this patch just does that.
This bug was found by LKP's cyclic performance regression tracking recently
with the vm-scalability test suite. I have bisected to commit:
3dec0ba0be6a ("mm/rmap: share the i_mmap_rwsem")
This commit didn't do anything wrong but revealed the irq_call_count
problem. IIUC, the commit makes rwc->remap_one in rmap_walk_file
concurrent with multiple threads. When remap_one is try_to_unmap_one(),
then multiple threads could queue flush TLB to the same CPU but only
one IPI will be sent.
Since the commit was added in Linux v3.19, the counting problem only
shows up from v3.19 onwards.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Cc: Alex Shi <alex.shi@linaro.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tomoki Sekiyama <tomoki.sekiyama.qu@hitachi.com>
Link: http://lkml.kernel.org/r/20160811074430.GA18163@aaronlu.sh.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
A recent patch changed the format of a swap PTE.
The comment explaining the format of the swap PTE is wrong about
the bits used for the swap type field. Amusingly, the ASCII art
and the patch description are correct, but the comment itself
is wrong.
As I was looking at this, I also noticed that the
SWP_OFFSET_FIRST_BIT has an off-by-one error. This does not
really hurt anything. It just wasted a bit of space in the PTE,
giving us 2^59 bytes of addressable space in our swapfiles
instead of 2^60. But, it doesn't match with the comments, and it
wastes a bit of space, so fix it.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luis R. Rodriguez <mcgrof@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Toshi Kani <toshi.kani@hp.com>
Fixes: 00839ee3b299 ("x86/mm: Move swap offset/type up in PTE to work around erratum")
Link: http://lkml.kernel.org/r/20160810172325.E56AD7DA@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
debug_putstr() is used to output strings without using printf-like
formatting but debug_putstr(v) is defined as early_printk(v) in
arch/x86/lib/kaslr.c.
This makes clang reports the following warning when building
with -Wformat-security:
arch/x86/lib/kaslr.c:57:15: warning: format string is not a string
literal (potentially insecure) [-Wformat-security]
debug_putstr(purpose);
^~~~~~~
Fix this by using "%s" in early_printk().
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20160806102039.27221-1-nicolas.iooss_linux@m4x.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
randconfig-4.8
This is the pxa changes for v4.8 cycle.
This is a tiny fix couple to enable changes in includes in
gpio API without breaking pxa boards.
* tag 'pxa-fixes-v4.8' of https://github.com/rjarzmik/linux:
ARM: pxa: add module.h for corgi symbol_get/symbol_put usage
ARM: pxa: add module.h for spitz symbol_get/symbol_put usage
|
|
Merge misc fixes from Andrew Morton:
"8 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm/slub.c: run free_partial() outside of the kmem_cache_node->list_lock
rmap: fix compound check logic in page_remove_file_rmap
mm, rmap: fix false positive VM_BUG() in page_add_file_rmap()
mm/page_alloc.c: recalculate some of node threshold when on/offline memory
mm/page_alloc.c: fix wrong initialization when sysctl_min_unmapped_ratio changes
thp: move shmem_huge_enabled() outside of SYSFS ifdef
revert "ARM: keystone: dts: add psci command definition"
rapidio: dereferencing an error pointer
|
|
Revert commit 51d5d12b8f3d ("ARM: keystone: dts: add psci command
definition"), which was inadvertently added twice.
Cc: Russell King - ARM Linux <linux@armlinux.org.uk>
Cc: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Even when PCI is disabled, ARCH_HISI selects HISILICON_IRQ_MBIGEN
triggerring the following config warning:
warning: (ARM64 && HISILICON_IRQ_MBIGEN) selects ARM_GIC_V3_ITS which
has unmet direct dependencies (PCI && PCI_MSI)
This patch makes selection of HISILICON_IRQ_MBIGEN conditional on PCI.
Cc: Ma Jun <majun258@huawei.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Even when PCI is disabled, ARCH_ALPINE selects ALPINE_MSI triggerring
the following config warning:
warning: (ARCH_ALPINE) selects ALPINE_MSI which has unmet direct
dependencies (PCI)
This patch makes selection of ALPINE_MSI conditional on PCI.
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Clearly QEMU is very permissive in how its PL310 model may be set up,
but the real hardware turns out to be far more particular about things
actually being correct. Fix up the DT description so that the real
thing actually boots:
- The arm,data-latency and arm,tag-latency properties need 3 cells to
be valid, otherwise we end up retaining the default 8-cycle latencies
which leads pretty quickly to lockup.
- The arm,dirty-latency property is only relevant to L210/L220, so get
rid of it.
- The cache geometry override also leads to lockup and/or general
misbehaviour. Irritatingly, the manual doesn't state the actual PL310
configuration, but based on the boardfile code and poking registers
from the Boot Monitor, it would seem to be 8 sets of 16KB ways.
With that, we can successfully boot to enjoy the fun of mismatched FPUs...
Cc: stable@vger.kernel.org
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
c90bb7b enabled the high speed UARTs of the Jetson TK1. Due to a merge
quirk, wrong addresses were introduced. Fix it and use the correct
addresses.
Thierry let me know, that there is another patch (b5896f67ab3c in
linux-next) in preparation which removes all the '0,' prefixes of unit
addresses on Tegra124 and is planned to go upstream in 4.8, so
this patch will get reverted then.
But for the moment, this patch is necessary to fix current misbehaviour.
Fixes: c90bb7b9b9 ("ARM: tegra: Add high speed UARTs to Jetson TK1 device tree")
Signed-off-by: Ralf Ramsauer <ralf@ramses-pyramidenbau.de>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Cc: stable@vger.kernel.org # v4.7
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This syscon needs to be looked up by clocks, flash protection
and other consumers.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This syscon needs to be looked up by flash protection, CLCD
display output settings and other consumers.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
For unknown reasons, we have to enable three symbols for a platform
to use a reset controller driver, otherwise we get a Kconfig
warning:
warning: (MACH_OX810SE) selects RESET_OXNAS which has unmet direct dependencies (RESET_CONTROLLER)
This selects the other two symbols for oxnas.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
The machine specific header files are exported for traditional
platforms, but not for the ones that use ARCH_MULTIPLATFORM, as
they could conflict with one another.
In case of ARM_SINGLE_ARMV7M, we end up also exporting them,
but that appears to be a mistake, and we should treat it the
same way as ARCH_MULTIPLATFORM here.
'make W=1' warns about this because it passes -Wmissing-includes
to gcc and the directories are not actually present.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Three platforms used to have header files in include/mach that
are now all gone, but the removed directories are still being
included, which leads to -Wmissing-include-dirs warnings.
This removes the extra -I flags.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add access checks to sys_oabi_epoll_wait() and sys_oabi_semtimedop().
This fixes CVE-2016-3857, a local privilege escalation under
CONFIG_OABI_COMPAT.
Cc: stable@vger.kernel.org
Reported-by: Chiachih Wu <wuchiachih@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Dave Weinstein <olorin@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag
Pull metag architecture fix from James Hogan:
"A single fix for a boot crash since a commit in the merge window.
Metag was unusual in calling show_mem() early, before setup_per_cpu_pageset(),
which is no longer safe. It doesn't add much value to the log, so the
fix just drops the call"
* tag 'metag-for-v4.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag:
metag: Drop show_mem() from mem_init()
|
|
manipulation
The Memory Protection Keys "rights register" (PKRU) is
XSAVE-managed, and is saved/restored along with the FPU state.
When kernel code accesses FPU regsisters, it does a delicate
dance with preempt. Otherwise, the context switching code can
get confused as to whether the most up-to-date state is in the
registers themselves or in the XSAVE buffer.
But, PKRU is not a normal FPU register. Using it does not
generate the normal device-not-available (#NM) exceptions which
means we can not manage it lazily, and the kernel completley
disallows using lazy mode when it is enabled.
The dance with preempt *only* occurs when managing the FPU
lazily. Since we never manage PKRU lazily, we do not have to do
the dance with preempt; we can access it directly. Doing it
this way saves a ton of complicated code (and is faster too).
Further, the XSAVES reenabling failed to patch a bit of code
in fpu__xfeature_set_state() the checked for compacted buffers.
That check caused fpu__xfeature_set_state() to silently refuse to
work when the kernel is using compacted XSAVE buffers. This
broke execute-only and future pkey_mprotect() support when using
compact XSAVE buffers.
But, removing fpu__xfeature_set_state() gets rid of this issue,
in addition to the nice cleanup and speedup.
This fixes the same thing as a fix that Sai posted:
https://lkml.org/lkml/2016/7/25/637
The fix that he posted is a much more obviously correct, but I
think we should just do this instead.
Reported-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Quentin Casasnovas <quentin.casasnovas@oracle.com>
Cc: Ravi Shankar <ravi.v.shankar@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yu-Cheng Yu <yu-cheng.yu@intel.com>
Link: http://lkml.kernel.org/r/20160727232040.7D060DAD@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Building an X86_64 kernel with W=1 throws a total of 9,948 lines of warnings of
this form for both 32-bit and 64-bit syscall tables. Given that the entire rest
of the build for my config only generates 8,375 lines of output, this is a big
reduction in the warnings generated.
The warnings follow this pattern:
./arch/x86/include/generated/asm/syscalls_32.h:885:21: warning: initialized field overwritten [-Woverride-init]
__SYSCALL_I386(379, compat_sys_pwritev2, )
^
arch/x86/entry/syscall_32.c:13:46: note: in definition of macro '__SYSCALL_I386'
#define __SYSCALL_I386(nr, sym, qual) [nr] = sym,
^~~
./arch/x86/include/generated/asm/syscalls_32.h:885:21: note: (near initialization for 'ia32_sys_call_table[379]')
__SYSCALL_I386(379, compat_sys_pwritev2, )
^
arch/x86/entry/syscall_32.c:13:46: note: in definition of macro '__SYSCALL_I386'
#define __SYSCALL_I386(nr, sym, qual) [nr] = sym,
Since we intentionally build the syscall tables this way, ignore that one
warning in the two files.
Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/7464.1470021890@turing-police.cc.vt.edu
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The latest UV kernel support panics when RHEL7 kexec's the kdump kernel
to make a dumpfile. This patch fixes the problem by turning off all UV
support if NUMA is off.
Tested-by: Frank Ramsay <framsay@sgi.com>
Tested-by: John Estabrook <estabrook@sgi.com>
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Dimitri Sivanich <sivanich@sgi.com>
Reviewed-by: Nathan Zimmer <nzimmer@sgi.com>
Cc: Alex Thorlton <athorlton@sgi.com>
Cc: Andrew Banman <abanman@sgi.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russ Anderson <rja@sgi.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20160801184050.577755634@asylum.americas.sgi.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
There are some circumstances where the UV4 BIOS cannot provide the
correct Proximity Node values to associate with specific Sockets and
Physical Nodes. The decision was made to remove these values from BIOS
and for the kernel to get these values from the standard ACPI tables.
Tested-by: Frank Ramsay <framsay@sgi.com>
Tested-by: John Estabrook <estabrook@sgi.com>
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Dimitri Sivanich <sivanich@sgi.com>
Reviewed-by: Nathan Zimmer <nzimmer@sgi.com>
Cc: Alex Thorlton <athorlton@sgi.com>
Cc: Andrew Banman <abanman@sgi.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russ Anderson <rja@sgi.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20160801184050.414210079@asylum.americas.sgi.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
a crash
Save the uv_systab::size field before doing the iounmap()
of the struct pointer, to avoid a NULL dereference crash.
Tested-by: Frank Ramsay <framsay@sgi.com>
Tested-by: John Estabrook <estabrook@sgi.com>
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Dimitri Sivanich <sivanich@sgi.com>
Reviewed-by: Nathan Zimmer <nzimmer@sgi.com>
Cc: Alex Thorlton <athorlton@sgi.com>
Cc: Andrew Banman <abanman@sgi.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russ Anderson <rja@sgi.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20160801184050.250424783@asylum.americas.sgi.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The UV4 Socket IDs are not guaranteed to equate to Node values which
can cause the GAM (Global Addressable Memory) table lookups to fail.
Fix this by using an independent index into the GAM table instead of
the Socket ID to reference the base address.
Tested-by: Frank Ramsay <framsay@sgi.com>
Tested-by: John Estabrook <estabrook@sgi.com>
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Dimitri Sivanich <sivanich@sgi.com>
Reviewed-by: Nathan Zimmer <nzimmer@sgi.com>
Cc: Alex Thorlton <athorlton@sgi.com>
Cc: Andrew Banman <abanman@sgi.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russ Anderson <rja@sgi.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20160801184050.048755337@asylum.americas.sgi.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Clarify why exactly RF cannot be restored properly by SYSRET to avoid
confusion.
No functionality change.
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20160803171429.GA2590@nazgul.tnic
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
There's a subtle preemption race on UP kernels:
Usually current->mm (and therefore mm->pgd) stays the same during the
lifetime of a task so it does not matter if a task gets preempted during
the read and write of the CR3.
But then, there is this scenario on x86-UP:
TaskA is in do_exit() and exit_mm() sets current->mm = NULL followed by:
-> mmput()
-> exit_mmap()
-> tlb_finish_mmu()
-> tlb_flush_mmu()
-> tlb_flush_mmu_tlbonly()
-> tlb_flush()
-> flush_tlb_mm_range()
-> __flush_tlb_up()
-> __flush_tlb()
-> __native_flush_tlb()
At this point current->mm is NULL but current->active_mm still points to
the "old" mm.
Let's preempt taskA _after_ native_read_cr3() by taskB. TaskB has its
own mm so CR3 has changed.
Now preempt back to taskA. TaskA has no ->mm set so it borrows taskB's
mm and so CR3 remains unchanged. Once taskA gets active it continues
where it was interrupted and that means it writes its old CR3 value
back. Everything is fine because userland won't need its memory
anymore.
Now the fun part:
Let's preempt taskA one more time and get back to taskB. This
time switch_mm() won't do a thing because oldmm (->active_mm)
is the same as mm (as per context_switch()). So we remain
with a bad CR3 / PGD and return to userland.
The next thing that happens is handle_mm_fault() with an address for
the execution of its code in userland. handle_mm_fault() realizes that
it has a PTE with proper rights so it returns doing nothing. But the
CPU looks at the wrong PGD and insists that something is wrong and
faults again. And again. And one more time…
This pagefault circle continues until the scheduler gets tired of it and
puts another task on the CPU. It gets little difficult if the task is a
RT task with a high priority. The system will either freeze or it gets
fixed by the software watchdog thread which usually runs at RT-max prio.
But waiting for the watchdog will increase the latency of the RT task
which is no good.
Fix this by disabling preemption across the critical code section.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Borislav Petkov <bp@suse.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm@kvack.org
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1470404259-26290-1-git-send-email-bigeasy@linutronix.de
[ Prettified the changelog. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
When using if_changed, we need to add FORCE as a dependency (see
Documentation/kbuild/makefiles.txt) otherwise we don't get command line
change checking amongst other things. This has resulted in vdsos not
being rebuilt when switching between big and little endian.
The vdso64/32ld commands have to be changed around to avoid pulling
FORCE into the linker command line (code copied from x86).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
When we introduced the little endian support, we added the endian flags
to CC directly using override. I don't know the history of why we did
that, I suspect no one does.
Although this mostly works, it has one bug, which is that CROSS32CC
doesn't get -mbig-endian. That means when the compiler is little endian
by default and the user is building big endian, vdso32 is incorrectly
compiled as little endian and the kernel fails to build.
Instead we can add the endian flags to cflags-y/aflags-y, and then
append those to KBUILD_CFLAGS/KBUILD_AFLAGS.
This has the advantage of being 1) less ugly, 2) the documented way of
adding flags in the arch Makefile and 3) it fixes building vdso32 with a
LE toolchain.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Default implementation expects 6 pages maximum are needed for low page
allocations. If KASLR memory randomization is enabled, the worse case
of e820 layout would require 12 pages (no large pages). It is due to the
PUD level randomization and the variable e820 memory layout.
This bug was found while doing extensive testing of KASLR memory
randomization on different type of hardware.
Signed-off-by: Thomas Garnier <thgarnie@google.com>
Cc: Aleksey Makarov <aleksey.makarov@linaro.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Baoquan He <bhe@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Borislav Petkov <bp@suse.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Fabian Frederick <fabf@skynet.be>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Lv Zheng <lv.zheng@intel.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J . Wysocki <rafael.j.wysocki@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: kernel-hardening@lists.openwall.com
Fixes: 021182e52fe0 ("Enable KASLR for physical mapping memory regions")
Link: http://lkml.kernel.org/r/1470762665-88032-2-git-send-email-thgarnie@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Initialize KASLR memory randomization after max_pfn is initialized. Also
ensure the size is rounded up. It could create problems on machines
with more than 1Tb of memory on certain random addresses.
Signed-off-by: Thomas Garnier <thgarnie@google.com>
Cc: Aleksey Makarov <aleksey.makarov@linaro.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Baoquan He <bhe@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Borislav Petkov <bp@suse.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Fabian Frederick <fabf@skynet.be>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Lv Zheng <lv.zheng@intel.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J . Wysocki <rafael.j.wysocki@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: kernel-hardening@lists.openwall.com
Fixes: 021182e52fe0 ("Enable KASLR for physical mapping memory regions")
Link: http://lkml.kernel.org/r/1470762665-88032-1-git-send-email-thgarnie@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Ville Syrjälä reports "The first time I run hwclock after rebooting
I get this:
open("/dev/rtc", O_RDONLY) = 3
ioctl(3, PHN_SET_REGS or RTC_UIE_ON, 0) = 0
select(4, [3], NULL, NULL, {10, 0}) = 0 (Timeout)
ioctl(3, PHN_NOT_OH or RTC_UIE_OFF, 0) = 0
close(3) = 0
On all subsequent runs I get this:
open("/dev/rtc", O_RDONLY) = 3
ioctl(3, PHN_SET_REGS or RTC_UIE_ON, 0) = -1 EINVAL (Invalid argument)
ioctl(3, RTC_RD_TIME, 0x7ffd76b3ae70) = -1 EINVAL (Invalid argument)
close(3) = 0"
This was caused by a stupid typo in a patch that should have been
a simple rename to move around contents of a header file, but
accidentally wrote zeroes into the rtc rather than reading from
it:
463a86304cae ("char/genrtc: x86: remove remnants of asm/rtc.h")
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: rtc-linux@googlegroups.com
Fixes: 463a86304cae ("char/genrtc: x86: remove remnants of asm/rtc.h")
Link: http://lkml.kernel.org/r/20160809195528.1604312-1-arnd@arndb.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Dmitry Vyukov has reported unexpected KASAN stackdepot growth:
https://github.com/google/kasan/issues/36
... which is caused by the APIC handlers not being present in .irqentry.text:
When building with CONFIG_FUNCTION_GRAPH_TRACER=y or CONFIG_KASAN=y, put the
APIC interrupt handlers into the .irqentry.text section. This is needed
because both KASAN and function graph tracer use __irqentry_text_start and
__irqentry_text_end to determine whether a function is an IRQ entry point.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Alexander Potapenko <glider@google.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: aryabinin@virtuozzo.com
Cc: kasan-dev@googlegroups.com
Cc: kcc@google.com
Cc: rostedt@goodmis.org
Link: http://lkml.kernel.org/r/1468575763-144889-1-git-send-email-glider@google.com
[ Minor edits. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This patch eliminates a source of imprecise APIC timer interrupts,
which imprecision may result in double interrupts or even late
interrupts.
The TSC deadline clockevent devices' configuration and registration
happens before the TSC frequency calibration is refined in
tsc_refine_calibration_work().
This results in the TSC clocksource and the TSC deadline clockevent
devices being configured with slightly different frequencies: the former
gets the refined one and the latter are configured with the inaccurate
frequency detected earlier by means of the "Fast TSC calibration using PIT".
Within the APIC code, introduce the notifier function
lapic_update_tsc_freq() which reconfigures all per-CPU TSC deadline
clockevent devices with the current tsc_khz.
Call it from the TSC code after TSC calibration refinement has happened.
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Christopher S. Hall <christopher.s.hall@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Link: http://lkml.kernel.org/r/20160714152255.18295-3-nicstange@gmail.com
[ Pushed #ifdef CONFIG_X86_LOCAL_APIC into header, improved changelog. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
clockevents frequency roundoff error
I noticed the following bug/misbehavior on certain Intel systems: with a
single task running on a NOHZ CPU on an Intel Haswell, I recognized
that I did not only get the one expected local_timer APIC interrupt, but
two per second at minimum. (!)
Further tracing showed that the first one precedes the programmed deadline
by up to ~50us and hence, it did nothing except for reprogramming the TSC
deadline clockevent device to trigger shortly thereafter again.
The reason for this is imprecise calibration, the timeout we program into
the APIC results in 'too short' timer interrupts. The core (hr)timer code
notices this (because it has a precise ktime source and sees the short
interrupt) and fixes it up by programming an additional very short
interrupt period.
This is obviously suboptimal.
The reason for the imprecise calibration is twofold, and this patch
fixes the first reason:
In setup_APIC_timer(), the registered clockevent device's frequency
is calculated by first dividing tsc_khz by TSC_DIVISOR and multiplying
it with 1000 afterwards:
(tsc_khz / TSC_DIVISOR) * 1000
The multiplication with 1000 is done for converting from kHz to Hz and the
division by TSC_DIVISOR is carried out in order to make sure that the final
result fits into an u32.
However, with the order given in this calculation, the roundoff error
introduced by the division gets magnified by a factor of 1000 by the
following multiplication.
To fix it, reversing the order of the division and the multiplication a la:
(tsc_khz * 1000) / TSC_DIVISOR
... reduces the roundoff error already.
Furthermore, if TSC_DIVISOR divides 1000, associativity holds:
(tsc_khz * 1000) / TSC_DIVISOR = tsc_khz * (1000 / TSC_DIVISOR)
and thus, the roundoff error even vanishes and the whole operation can be
carried out within 32 bits.
The powers of two that divide 1000 are 2, 4 and 8. A value of 8 for
TSC_DIVISOR still allows for TSC frequencies up to
2^32 / 10^9ns * 8 = 34.4GHz which is way larger than anything to expect
in the next years.
Thus we also replace the current TSC_DIVISOR value of 32 by 8. Reverse
the order of the divison and the multiplication in the calculation of
the registered clockevent device's frequency.
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Christopher S. Hall <christopher.s.hall@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Link: http://lkml.kernel.org/r/20160714152255.18295-2-nicstange@gmail.com
[ Improved changelog. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
We cannot do those initializations from apply_feature_fixups() as
this function runs in a very restricted environment on 32-bit where
the kernel isn't running at its linked address and the PTRRELOC()
macro must be used for any global accesss.
Instead, split them into a separtate steup_feature_keys() function
which is called in a more suitable spot on ppc32.
Fixes: 309b315b6ec6 ("powerpc: Call jump_label_init() in apply_feature_fixups()")
Reported-and-tested-by: Christian Kujau <lists@nerdbynature.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
We don't identify the machine type anymore...
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This makes it easier to debug crashes that happen very early before
the kernel takes over Open Firmware by allowing us to relate the OF
reported crashing addresses to offsets within the kernel.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Both set_memory_ro() and set_memory_rw() will modify the page
attributes of at least one page, even if the numpages parameter is
zero.
The author expected that calling these functions with numpages == zero
would never happen. However with the new 444d13ff10fb ("modules: add
ro_after_init support") feature this happens frequently.
Therefore do the right thing and make these two functions return
gracefully if nothing should be done.
Fixes crashes on module load like this one:
Unable to handle kernel pointer dereference in virtual kernel address space
Failing address: 000003ff80008000 TEID: 000003ff80008407
Fault in home space mode while using kernel ASCE.
AS:0000000000d18007 R3:00000001e6aa4007 S:00000001e6a10800 P:00000001e34ee21d
Oops: 0004 ilc:3 [#1] SMP
Modules linked in: x_tables
CPU: 10 PID: 1 Comm: systemd Not tainted 4.7.0-11895-g3fa9045 #4
Hardware name: IBM 2964 N96 703 (LPAR)
task: 00000001e9118000 task.stack: 00000001e9120000
Krnl PSW : 0704e00180000000 00000000005677f8 (rb_erase+0xf0/0x4d0)
R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:3 CC:2 PM:0 RI:0 EA:3
Krnl GPRS: 000003ff80008b20 000003ff80008b20 000003ff80008b70 0000000000b9d608
000003ff80008b20 0000000000000000 00000001e9123e88 000003ff80008950
00000001e485ab40 000003ff00000000 000003ff80008b00 00000001e4858480
0000000100000000 000003ff80008b68 00000000001d5998 00000001e9123c28
Krnl Code: 00000000005677e8: ec1801c3007c cgij %r1,0,8,567b6e
00000000005677ee: e32010100020 cg %r2,16(%r1)
#00000000005677f4: a78401c2 brc 8,567b78
>00000000005677f8: e35010080024 stg %r5,8(%r1)
00000000005677fe: ec5801af007c cgij %r5,0,8,567b5c
0000000000567804: e30050000024 stg %r0,0(%r5)
000000000056780a: ebacf0680004 lmg %r10,%r12,104(%r15)
0000000000567810: 07fe bcr 15,%r14
Call Trace:
([<000003ff80008900>] __this_module+0x0/0xffffffffffffd700 [x_tables])
([<0000000000264fd4>] do_init_module+0x12c/0x220)
([<00000000001da14a>] load_module+0x24e2/0x2b10)
([<00000000001da976>] SyS_finit_module+0xbe/0xd8)
([<0000000000803b26>] system_call+0xd6/0x264)
Last Breaking-Event-Address:
[<000000000056771a>] rb_erase+0x12/0x4d0
Kernel panic - not syncing: Fatal exception: panic_on_oops
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reported-and-tested-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Fixes: e8a97e42dc98 ("s390/pageattr: allow kernel page table splitting")
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Commit 8d460f6156cd ("powerpc/process: Add the function
flush_tmregs_to_thread") added flush_tmregs_to_thread() and included
the assumption that it would only be called for a task which is not
current.
Although this is correct for ptrace, when generating a core dump, some
of the routines which call flush_tmregs_to_thread() are called. This
leads to a WARNing such as:
Not expecting ptrace on self: TM regs may be incorrect
------------[ cut here ]------------
WARNING: CPU: 123 PID: 7727 at arch/powerpc/kernel/process.c:1088 flush_tmregs_to_thread+0x78/0x80
CPU: 123 PID: 7727 Comm: libvirtd Not tainted 4.8.0-rc1-gcc6x-g61e8a0d #1
task: c000000fe631b600 task.stack: c000000fe63b0000
NIP: c00000000001a1a8 LR: c00000000001a1a4 CTR: c000000000717780
REGS: c000000fe63b3420 TRAP: 0700 Not tainted (4.8.0-rc1-gcc6x-g61e8a0d)
MSR: 900000010282b033 <SF,HV,VEC,VSX,EE,FP,ME,IR,DR,RI,LE,TM[E]> CR: 28004222 XER: 20000000
...
NIP [c00000000001a1a8] flush_tmregs_to_thread+0x78/0x80
LR [c00000000001a1a4] flush_tmregs_to_thread+0x74/0x80
Call Trace:
flush_tmregs_to_thread+0x74/0x80 (unreliable)
vsr_get+0x64/0x1a0
elf_core_dump+0x604/0x1430
do_coredump+0x5fc/0x1200
get_signal+0x398/0x740
do_signal+0x54/0x2b0
do_notify_resume+0x98/0xb0
ret_from_except_lite+0x70/0x74
So fix flush_tmregs_to_thread() to detect the case where it is called on
current, and a transaction is active, and in that case flush the TM regs
to the thread_struct.
This patch also moves flush_tmregs_to_thread() into ptrace.c as it is
only called from that file.
Fixes: 8d460f6156cd ("powerpc/process: Add the function flush_tmregs_to_thread")
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
[mpe: Flesh out change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Commit 7aef4136566b0 ("powerpc32: rewrite csum_partial_copy_generic()
based on copy_tofrom_user()") introduced a bug when destination
address is odd and initial csum is not null
In that (rare) case the initial csum value has to be rotated one byte
as well as the resulting value is
This patch also fixes related comments
Fixes: 7aef4136566b0 ("powerpc32: rewrite csum_partial_copy_generic() based on copy_tofrom_user()")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
During boot, sometimes the kernel will test to see if an instruction
causes an undefined instruction exception. Unfortunately, the exit
path for these exceptions did not restore the address limit, which
causes the rootfs mount code to fail. Fix the missing address limit
restoration.
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
The late_alloc() PTE allocation function used by create_mapping_late()
does not call pgtable_page_ctor() on PTE pages it allocates, leaving
the per-page spinlock uninitialized.
Since generic page table manipulation code may assume that translation
table pages that are not owned by init_mm are covered by fully
constructed struct pages, the following crash may occur with the new
UEFI memory attributes table code.
efi: memattr: Processing EFI Memory Attributes table:
efi: memattr: 0x0000ffa16000-0x0000ffa82fff [Runtime Code |RUN| | |XP| | | | | | | | ]
Unable to handle kernel NULL pointer dereference at virtual address 00000010
pgd = c0204000
[00000010] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.7.0-rc4-00063-g3882aa7b340b #361
Hardware name: Generic DT based system
task: ed858000 ti: ed842000 task.ti: ed842000
PC is at __lock_acquire+0xa0/0x19a8
...
[<c038c830>] (__lock_acquire) from [<c038e4f8>] (lock_acquire+0x6c/0x88)
[<c038e4f8>] (lock_acquire) from [<c0c06134>] (_raw_spin_lock+0x2c/0x3c)
[<c0c06134>] (_raw_spin_lock) from [<c0410384>] (apply_to_page_range+0xe8/0x238)
[<c0410384>] (apply_to_page_range) from [<c1205f34>] (efi_set_mapping_permissions+0x54/0x5c)
[<c1205f34>] (efi_set_mapping_permissions) from [<c1247474>] (efi_memattr_apply_permissions+0x2b8/0x378)
[<c1247474>] (efi_memattr_apply_permissions) from [<c1248258>] (arm_enable_runtime_services+0x1f0/0x22c)
[<c1248258>] (arm_enable_runtime_services) from [<c0301f0c>] (do_one_initcall+0x44/0x174)
[<c0301f0c>] (do_one_initcall) from [<c1200d10>] (kernel_init_freeable+0x90/0x1e8)
[<c1200d10>] (kernel_init_freeable) from [<c0bff690>] (kernel_init+0x8/0x114)
[<c0bff690>] (kernel_init) from [<c0307ed0>] (ret_from_fork+0x14/0x24)
The crash is due to the fact that the UEFI page tables are not owned by
init_mm, but are not covered by fully constructed struct pages.
Given that the UEFI subsystem is currently the only user of
create_mapping_late(), add an unconditional call to pgtable_page_ctor() to
late_alloc().
Fixes: 9fc68b717c24 ("ARM/efi: Apply strict permissions for UEFI Runtime Services regions")
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
To limit the amount of mapped low memory, we determine a physical address
boundary based on the start of the vmalloc area using __pa().
Strictly speaking, the vmalloc area location is arbitrary and does not
necessarily corresponds to a valid physical address. For example, if
PAGE_OFFSET = 0x80000000
PHYS_OFFSET = 0x90000000
vmalloc_min = 0xf0000000
then __pa(vmalloc_min) overflows and returns a wrapped 0 when phys_addr_t
is a 32-bit type. Then the code that follows determines that the entire
physical memory is above that boundary and no low memory gets mapped at
all:
|[...]
|Machine model: Freescale i.MX51 NA04 Board
|Ignoring RAM at 0x90000000-0xb0000000 (!CONFIG_HIGHMEM)
|Consider using a HIGHMEM enabled kernel.
To avoid this problem let's make vmalloc_limit a 64-bit value all the
time and determine that boundary explicitly without using __pa().
Reported-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
driver
Since IRQCHIP_DECLARE now flags the GPC node as already populated, the
GPC power domain driver is never probed unless we clear the flag again.
Fixes: 15cc2ed6dcf9 ("of/irq: Mark initialised interrupt controllers as populated")
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
The recent commit 599d0c954f91 ("mm, vmscan: move LRU lists to node"),
changed memory management code so that show_mem() is no longer safe to
call prior to setup_per_cpu_pageset(), as pgdat->per_cpu_nodestats will
still be NULL. This causes an oops on metag due to the call to
show_mem() from mem_init():
node_page_state_snapshot(...) + 0x48
pgdat_reclaimable(struct pglist_data * pgdat = 0x402517a0)
show_free_areas(unsigned int filter = 0) + 0x2cc
show_mem(unsigned int filter = 0) + 0x18
mem_init()
mm_init()
start_kernel() + 0x204
This wasn't a problem before with zone_reclaimable() as zone_pcp_init()
was already setting zone->pageset to &boot_pageset, via setup_arch() and
paging_init(), which happens before mm_init():
zone_pcp_init(...)
free_area_init_core(...) + 0x138
free_area_init_node(int nid = 0, ...) + 0x1a0
free_area_init_nodes(...) + 0x440
paging_init(unsigned long mem_end = 0x4fe00000) + 0x378
setup_arch(char ** cmdline_p = 0x4024e038) + 0x2b8
start_kernel() + 0x54
No other arches appear to call show_mem() during boot, and it doesn't
really add much value to the log, so lets just drop it from mem_init().
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Mel Gorman <mgorman@techsingularity.net>
Cc: linux-metag@vger.kernel.org
|
