summaryrefslogtreecommitdiff
path: root/arch
AgeCommit message (Collapse)Author
2020-07-22x86/unwind/orc: Fix ORC for newly forked tasksJosh Poimboeuf
The ORC unwinder fails to unwind newly forked tasks which haven't yet run on the CPU. It correctly reads the 'ret_from_fork' instruction pointer from the stack, but it incorrectly interprets that value as a call stack address rather than a "signal" one, so the address gets incorrectly decremented in the call to orc_find(), resulting in bad ORC data. Fix it by forcing 'ret_from_fork' frames to be signal frames. Reported-by: Wang ShaoBo <bobo.shaobowang@huawei.com> Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Wang ShaoBo <bobo.shaobowang@huawei.com> Link: https://lkml.kernel.org/r/f91a8778dde8aae7f71884b5df2b16d552040441.1594994374.git.jpoimboe@redhat.com
2020-07-22Merge tag 'imx-fixes-5.8-3' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes i.MX fixes for 5.8, round 3: - A couple of FEC2 phy-mode fixes on imx6sx-sabreauto and imx6sx-sdb board. - One fix on imx6qdl-icore pin muxing to get USB OTG_ID and SD card detect work correctly. * tag 'imx-fixes-5.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: ARM: dts: imx6qdl-icore: Fix OTG_ID pin and sdcard detect ARM: dts: imx6sx-sabreauto: Fix the phy-mode on fec2 ARM: dts: imx6sx-sdb: Fix the phy-mode on fec2 Link: https://lore.kernel.org/r/20200720040148.GA20462@dragon Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2020-07-22Merge tag 'sunxi-fixes-for-5.8-1' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes Two fixes for the Allwinner SoCs, one to relax the CMA allocation ranges that were failing on older SoCs and one to fix Cedrus on the H6. * tag 'sunxi-fixes-for-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: arm64: dts: allwinner: h6: Fix Cedrus IOMMU usage ARM: dts sunxi: Relax a bit the CMA pool allocation range Link: https://lore.kernel.org/r/e24f0608-6a4f-4163-b99e-a5f48e796184.lettre@localhost Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2020-07-22Merge tag 'media/v5.8-3' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media into master Pull media fixes from Mauro Carvalho Chehab: "A series of fixes for the upcoming atomisp driver. They solve issues when probing atomisp on devices with multiple cameras and get rid of warnings when built with W=1. The diffstat is a bit long, as this driver has several abstractions. The patches that solved the issues with W=1 had to get rid of some duplicated code (there used to have 2 versions of the same code, one for ISP2401 and another one for ISP2400). As this driver is not in 5.7, such changes won't cause regressions" * tag 'media/v5.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (38 commits) Revert "media: atomisp: keep the ISP powered on when setting it" media: atomisp: fix mask and shift operation on ISPSSPM0 media: atomisp: move system_local consts into a C file media: atomisp: get rid of version-specific system_local.h media: atomisp: move global stuff into a common header media: atomisp: remove non-used 32-bits consts at system_local media: atomisp: get rid of some unused static vars media: atomisp: Fix error code in ov5693_probe() media: atomisp: Replace trace_printk by pr_info media: atomisp: Fix __func__ style warnings media: atomisp: fix help message for ISP2401 selection media: atomisp: i2c: atomisp-ov2680.c: fixed a brace coding style issue. media: atomisp: make const arrays static, makes object smaller media: atomisp: Clean up non-existing folders from Makefile media: atomisp: Get rid of ACPI specifics in gmin_subdev_add() media: atomisp: Provide Gmin subdev as parameter to gmin_subdev_add() media: atomisp: Use temporary variable for device in gmin_subdev_add() media: atomisp: Refactor PMIC detection to a separate function media: atomisp: Deduplicate return ret in gmin_i2c_write() media: atomisp: Make pointer to PMIC client global ...
2020-07-22x86, vmlinux.lds: Page-align end of ..page_aligned sectionsJoerg Roedel
On x86-32 the idt_table with 256 entries needs only 2048 bytes. It is page-aligned, but the end of the .bss..page_aligned section is not guaranteed to be page-aligned. As a result, objects from other .bss sections may end up on the same 4k page as the idt_table, and will accidentially get mapped read-only during boot, causing unexpected page-faults when the kernel writes to them. This could be worked around by making the objects in the page aligned sections page sized, but that's wrong. Explicit sections which store only page aligned objects have an implicit guarantee that the object is alone in the page in which it is placed. That works for all objects except the last one. That's inconsistent. Enforcing page sized objects for these sections would wreckage memory sanitizers, because the object becomes artificially larger than it should be and out of bound access becomes legit. Align the end of the .bss..page_aligned and .data..page_aligned section on page-size so all objects places in these sections are guaranteed to have their own page. [ tglx: Amended changelog ] Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Kees Cook <keescook@chromium.org> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20200721093448.10417-1-joro@8bytes.org
2020-07-21xtensa: fix access check in csum_and_copy_from_userMax Filippov
Commit d341659f470b ("xtensa: switch to providing csum_and_copy_from_user()") introduced access check, but incorrectly tested dst instead of src. Fix access_ok argument in csum_and_copy_from_user. Cc: Al Viro <viro@zeniv.linux.org.uk> Fixes: d341659f470b ("xtensa: switch to providing csum_and_copy_from_user()") Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2020-07-21ARM: 8988/1: mmu: fix crash in EFI calls due to p4d typo in ↵Ard Biesheuvel
create_mapping_late() Commit 84e6ffb2c49c7901 ("arm: add support for folded p4d page tables") updated create_mapping_late() to take folded P4Ds into account when creating mappings, but inverted the p4d_alloc() failure test, resulting in no mapping to be created at all. When the EFI rtc driver subsequently tries to invoke the EFI GetTime() service, the memory regions covering the EFI data structures are missing from the page tables, resulting in a crash like Unable to handle kernel paging request at virtual address 5ae0cf28 pgd = (ptrval) [5ae0cf28] *pgd=80000040205003, *pmd=00000000 Internal error: Oops: 207 [#1] SMP THUMB2 Modules linked in: CPU: 0 PID: 7 Comm: kworker/u32:0 Not tainted 5.7.0+ #92 Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015 Workqueue: efi_rts_wq efi_call_rts PC is at efi_call_rts+0x94/0x294 LR is at efi_call_rts+0x83/0x294 pc : [<c0b4f098>] lr : [<c0b4f087>] psr: 30000033 sp : e6219ef0 ip : 00000000 fp : ffffe000 r10: 00000000 r9 : 00000000 r8 : 30000013 r7 : e6201dd0 r6 : e6201ddc r5 : 00000000 r4 : c181f264 r3 : 5ae0cf10 r2 : 00000001 r1 : e6201dd0 r0 : e6201ddc Flags: nzCV IRQs on FIQs on Mode SVC_32 ISA Thumb Segment none Control: 70c5383d Table: 661cc840 DAC: 00000001 Process kworker/u32:0 (pid: 7, stack limit = 0x(ptrval)) ... [<c0b4f098>] (efi_call_rts) from [<c0448219>] (process_one_work+0x16d/0x3d8) [<c0448219>] (process_one_work) from [<c0448581>] (worker_thread+0xfd/0x408) [<c0448581>] (worker_thread) from [<c044ca7b>] (kthread+0x103/0x104) ... Fixes: 84e6ffb2c49c7901 ("arm: add support for folded p4d page tables") Reviewed-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
2020-07-21ARM: 8987/1: VDSO: Fix incorrect clock_gettime64Jaedon Shin
__vdso_*() should be removed and fallback used if CNTCVT is not available by cntvct_functional(). __vdso_clock_gettime64 when added previous commit is using the incorrect CNTCVT value in that state. __vdso_clock_gettime64 is also added to remove it's symbol. Cc: stable@vger.kernel.org Fixes: 74d06efb9c2f ("ARM: 8932/1: Add clock_gettime64 entry point") Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com> Tested-by: Robin Murphy <robin.mruphy@arm.com> Signed-off-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
2020-07-21ARM: 8986/1: hw_breakpoint: Don't invoke overflow handler on uaccess watchpointsWill Deacon
Unprivileged memory accesses generated by the so-called "translated" instructions (e.g. LDRT) in kernel mode can cause user watchpoints to fire unexpectedly. In such cases, the hw_breakpoint logic will invoke the user overflow handler which will typically raise a SIGTRAP back to the current task. This is futile when returning back to the kernel because (a) the signal won't have been delivered and (b) userspace can't handle the thing anyway. Avoid invoking the user overflow handler for watchpoints triggered by kernel uaccess routines, and instead single-step over the faulting instruction as we would if no overflow handler had been installed. Cc: <stable@vger.kernel.org> Fixes: f81ef4a920c8 ("ARM: 6356/1: hw-breakpoint: add ARM backend for the hw-breakpoint framework") Reported-by: Luis Machado <luis.machado@linaro.org> Tested-by: Luis Machado <luis.machado@linaro.org> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
2020-07-21parisc: Add atomic64_set_release() define to avoid CPU soft lockupsJohn David Anglin
Stalls are quite frequent with recent kernels. I enabled CONFIG_SOFTLOCKUP_DETECTOR and I caught the following stall: watchdog: BUG: soft lockup - CPU#0 stuck for 22s! [cc1:22803] CPU: 0 PID: 22803 Comm: cc1 Not tainted 5.6.17+ #3 Hardware name: 9000/800/rp3440 IAOQ[0]: d_alloc_parallel+0x384/0x688 IAOQ[1]: d_alloc_parallel+0x388/0x688 RP(r2): d_alloc_parallel+0x134/0x688 Backtrace: [<000000004036974c>] __lookup_slow+0xa4/0x200 [<0000000040369fc8>] walk_component+0x288/0x458 [<000000004036a9a0>] path_lookupat+0x88/0x198 [<000000004036e748>] filename_lookup+0xa0/0x168 [<000000004036e95c>] user_path_at_empty+0x64/0x80 [<000000004035d93c>] vfs_statx+0x104/0x158 [<000000004035dfcc>] __do_sys_lstat64+0x44/0x80 [<000000004035e5a0>] sys_lstat64+0x20/0x38 [<0000000040180054>] syscall_exit+0x0/0x14 The code was stuck in this loop in d_alloc_parallel: 4037d414: 0e 00 10 dc ldd 0(r16),ret0 4037d418: c7 fc 5f ed bb,< ret0,1f,4037d414 <d_alloc_parallel+0x384> 4037d41c: 08 00 02 40 nop This is the inner loop of bit_spin_lock which is called by hlist_bl_unlock in d_alloc_parallel: static inline void bit_spin_lock(int bitnum, unsigned long *addr) { /* * Assuming the lock is uncontended, this never enters * the body of the outer loop. If it is contended, then * within the inner loop a non-atomic test is used to * busywait with less bus contention for a good time to * attempt to acquire the lock bit. */ preempt_disable(); #if defined(CONFIG_SMP) || defined(CONFIG_DEBUG_SPINLOCK) while (unlikely(test_and_set_bit_lock(bitnum, addr))) { preempt_enable(); do { cpu_relax(); } while (test_bit(bitnum, addr)); preempt_disable(); } #endif __acquire(bitlock); } After consideration, I realized that we must be losing bit unlocks. Then, I noticed that we missed defining atomic64_set_release(). Adding this define fixes the stalls in bit operations. Signed-off-by: Dave Anglin <dave.anglin@bell.net> Cc: stable@vger.kernel.org Signed-off-by: Helge Deller <deller@gmx.de>
2020-07-21s390/cpum_cf,perf: change DFLT_CCERROR counter nameThomas Richter
Change the counter name DLFT_CCERROR to DLFT_CCFINISH on IBM z15. This counter counts completed DEFLATE instructions with exit code 0, 1 or 2. Since exit code 0 means success and exit code 1 or 2 indicate errors, change the counter name to avoid confusion. This counter is incremented each time the DEFLATE instruction completed regardless if an error was detected or not. Fixes: d68d5d51dc89 ("s390/cpum_cf: Add new extended counters for IBM z15") Fixes: e7950166e402 ("perf vendor events s390: Add new deflate counters for IBM z15") Cc: stable@vger.kernel.org # v5.7 Signed-off-by: Thomas Richter <tmricht@linux.ibm.com> Reviewed-by: Sumanth Korikkar <sumanthk@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
2020-07-21parisc: add support for cmpxchg on u8 pointersLiam Beguin
The kernel test bot reported[1] that using set_mask_bits on a u8 causes the following issue on parisc: hppa-linux-ld: drivers/phy/ti/phy-tusb1210.o: in function `tusb1210_probe': >> (.text+0x2f4): undefined reference to `__cmpxchg_called_with_bad_pointer' >> hppa-linux-ld: (.text+0x324): undefined reference to `__cmpxchg_called_with_bad_pointer' hppa-linux-ld: (.text+0x354): undefined reference to `__cmpxchg_called_with_bad_pointer' Add support for cmpxchg on u8 pointers. [1] https://lore.kernel.org/patchwork/patch/1272617/#1468946 Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Liam Beguin <liambeguin@gmail.com> Tested-by: Dave Anglin <dave.anglin@bell.net> Signed-off-by: Helge Deller <deller@gmx.de>
2020-07-20riscv: kasan: use local_tlb_flush_all() to avoid uninitialized __sbi_rfenceVincent Chen
It fails to boot the v5.8-rc4 kernel with CONFIG_KASAN because kasan_init and kasan_early_init use uninitialized __sbi_rfence as executing the tlb_flush_all(). Actually, at this moment, only the CPU which is responsible for the system initialization enables the MMU. Other CPUs are parking at the .Lsecondary_start. Hence the tlb_flush_all() is able to be replaced by local_tlb_flush_all() to avoid using uninitialized __sbi_rfence. Signed-off-by: Vincent Chen <vincent.chen@sifive.com> Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
2020-07-20ARM: dts: imx6qdl-icore: Fix OTG_ID pin and sdcard detectMichael Trimarchi
The current pin muxing scheme muxes GPIO_1 pad for USB_OTG_ID because of which when card is inserted, usb otg is enumerated and the card is never detected. [ 64.492645] cfg80211: failed to load regulatory.db [ 64.492657] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 76.343711] ci_hdrc ci_hdrc.0: EHCI Host Controller [ 76.349742] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 2 [ 76.388862] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00 [ 76.396650] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.08 [ 76.405412] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 76.412763] usb usb2: Product: EHCI Host Controller [ 76.417666] usb usb2: Manufacturer: Linux 5.8.0-rc1-next-20200618 ehci_hcd [ 76.424623] usb usb2: SerialNumber: ci_hdrc.0 [ 76.431755] hub 2-0:1.0: USB hub found [ 76.435862] hub 2-0:1.0: 1 port detected The TRM mentions GPIO_1 pad should be muxed/assigned for card detect and ENET_RX_ER pad for USB_OTG_ID for proper operation. This patch fixes pin muxing as per TRM and is tested on a i.Core 1.5 MX6 DL SOM. [ 22.449165] mmc0: host does not support reading read-only switch, assuming write-enable [ 22.459992] mmc0: new high speed SDHC card at address 0001 [ 22.469725] mmcblk0: mmc0:0001 EB1QT 29.8 GiB [ 22.478856] mmcblk0: p1 p2 Fixes: 6df11287f7c9 ("ARM: dts: imx6q: Add Engicam i.CoreM6 Quad/Dual initial support") Cc: stable@vger.kernel.org Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2020-07-20ARM: dts: imx6sx-sabreauto: Fix the phy-mode on fec2Fabio Estevam
Commit 0672d22a1924 ("ARM: dts: imx: Fix the AR803X phy-mode") fixed the phy-mode for fec1, but missed to fix it for the fec2 node. Fix fec2 to also use "rgmii-id" as the phy-mode. Cc: <stable@vger.kernel.org> Fixes: 0672d22a1924 ("ARM: dts: imx: Fix the AR803X phy-mode") Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2020-07-20ARM: dts: imx6sx-sdb: Fix the phy-mode on fec2Fabio Estevam
Commit 0672d22a1924 ("ARM: dts: imx: Fix the AR803X phy-mode") fixed the phy-mode for fec1, but missed to fix it for the fec2 node. Fix fec2 to also use "rgmii-id" as the phy-mode. Cc: <stable@vger.kernel.org> Fixes: 0672d22a1924 ("ARM: dts: imx: Fix the AR803X phy-mode") Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2020-07-19arm64: dts: clearfog-gt-8k: fix switch link configurationRussell King
The commit below caused a regression for clearfog-gt-8k, where the link between the switch and the host does not come up. Investigation revealed two issues: - MV88E6xxx DSA no longer allows an in-band link to come up as the link is programmed to be forced down. Commit "net: dsa: mv88e6xxx: fix in-band AN link establishment" addresses this. - The dts configured dissimilar link modes at each end of the host to switch link; the host was configured using a fixed link (so has no in-band status) and the switch was configured to expect in-band status. With both issues fixed, the regression is resolved. Fixes: 34b5e6a33c1a ("net: dsa: mv88e6xxx: Configure MAC when using fixed link") Reported-by: Martin Rowe <martin.p.rowe@gmail.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-19copy_xstate_to_kernel: Fix typo which caused GDB regressionKevin Buettner
This fixes a regression encountered while running the gdb.base/corefile.exp test in GDB's test suite. In my testing, the typo prevented the sw_reserved field of struct fxregs_state from being output to the kernel XSAVES area. Thus the correct mask corresponding to XCR0 was not present in the core file for GDB to interrogate, resulting in the following behavior: [kev@f32-1 gdb]$ ./gdb -q testsuite/outputs/gdb.base/corefile/corefile testsuite/outputs/gdb.base/corefile/corefile.core Reading symbols from testsuite/outputs/gdb.base/corefile/corefile... [New LWP 232880] warning: Unexpected size of section `.reg-xstate/232880' in core file. With the typo fixed, the test works again as expected. Signed-off-by: Kevin Buettner <kevinb@redhat.com> Fixes: 9e4636545933 ("copy_xstate_to_kernel(): don't leave parts of destination uninitialized") Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Dave Airlie <airlied@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-07-19Merge tag 'x86-urgent-2020-07-19' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into master Pull x86 fixes from Thomas Gleixner: "A pile of fixes for x86: - Fix the I/O bitmap invalidation on XEN PV, which was overlooked in the recent ioperm/iopl rework. This caused the TSS and XEN's I/O bitmap to get out of sync. - Use the proper vectors for HYPERV. - Make disabling of stack protector for the entry code work with GCC builds which enable stack protector by default. Removing the option is not sufficient, it needs an explicit -fno-stack-protector to shut it off. - Mark check_user_regs() noinstr as it is called from noinstr code. The missing annotation causes it to be placed in the text section which makes it instrumentable. - Add the missing interrupt disable in exc_alignment_check() - Fixup a XEN_PV build dependency in the 32bit entry code - A few fixes to make the Clang integrated assembler happy - Move EFI stub build to the right place for out of tree builds - Make prepare_exit_to_usermode() static. It's not longer called from ASM code" * tag 'x86-urgent-2020-07-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/boot: Don't add the EFI stub to targets x86/entry: Actually disable stack protector x86/ioperm: Fix io bitmap invalidation on Xen PV x86: math-emu: Fix up 'cmp' insn for clang ias x86/entry: Fix vectors to IDTENTRY_SYSVEC for CONFIG_HYPERV x86/entry: Add compatibility with IAS x86/entry/common: Make prepare_exit_to_usermode() static x86/entry: Mark check_user_regs() noinstr x86/traps: Disable interrupts in exc_aligment_check() x86/entry/32: Fix XEN_PV build dependency
2020-07-19Merge tag 'irq-urgent-2020-07-19' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into master Pull irq fixes from Thomas Gleixner: "Two fixes for the interrupt subsystem: - Make the handling of the firmware node consistent and do not free the node after the domain has been created successfully. The core code stores a pointer to it which can lead to a use after free or double free. This used to "work" because the pointer was not stored when the initial code was written, but at some point later it was required to store it. Of course nobody noticed that the existing users break that way. - Handle affinity setting on inactive interrupts correctly when hierarchical irq domains are enabled. When interrupts are inactive with the modern hierarchical irqdomain design, the interrupt chips are not necessarily in a state where affinity changes can be handled. The legacy irq chip design allowed this because interrupts are immediately fully initialized at allocation time. X86 has a hacky workaround for this, but other implementations do not. This cased malfunction on GIC-V3. Instead of playing whack a mole to find all affected drivers, change the core code to store the requested affinity setting and then establish it when the interrupt is allocated, which makes the X86 hack go away" * tag 'irq-urgent-2020-07-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: genirq/affinity: Handle affinity setting on inactive interrupts correctly irqdomain/treewide: Keep firmware node unconditionally allocated
2020-07-19x86/boot: Don't add the EFI stub to targetsArvind Sankar
vmlinux-objs-y is added to targets, which currently means that the EFI stub gets added to the targets as well. It shouldn't be added since it is built elsewhere. This confuses Makefile.build which interprets the EFI stub as a target $(obj)/$(objtree)/drivers/firmware/efi/libstub/lib.a and will create drivers/firmware/efi/libstub/ underneath arch/x86/boot/compressed, to hold this supposed target, if building out-of-tree. [0] Fix this by pulling the stub out of vmlinux-objs-y into efi-obj-y. [0] See scripts/Makefile.build near the end: # Create directories for object files if they do not exist Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Masahiro Yamada <masahiroy@kernel.org> Acked-by: Ard Biesheuvel <ardb@kernel.org> Link: https://lkml.kernel.org/r/20200715032631.1562882-1-nivedita@alum.mit.edu
2020-07-19x86/entry: Actually disable stack protectorKees Cook
Some builds of GCC enable stack protector by default. Simply removing the arguments is not sufficient to disable stack protector, as the stack protector for those GCC builds must be explicitly disabled. Remove the argument removals and add -fno-stack-protector. Additionally include missed x32 argument updates, and adjust whitespace for readability. Fixes: 20355e5f73a7 ("x86/entry: Exclude low level entry code from sanitizing") Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/202006261333.585319CA6B@keescook
2020-07-18Merge tag 'riscv-for-linus-5.8-rc6' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux into master Pull RISC-V fixes from Palmer Dabbelt: "Two fixes: - 16KiB kernel stacks on rv64, which fixes a lot of crashes. - Rolling an mmiowb() into the scheduler, which when combined with Will's fix to the mmiowb()-on-spinlock should fix the PREEMPT issues we've been seeing" * tag 'riscv-for-linus-5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: RISC-V: Upgrade smp_mb__after_spinlock() to iorw,iorw riscv: use 16KB kernel stack on 64-bit
2020-07-18Merge tag 'powerpc-5.8-7' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux into master Pull powerpc fixes from Michael Ellerman: "Some more powerpc fixes for 5.8: - A fix to the VAS code we merged this cycle, to report the proper error code to userspace for address translation failures. And a selftest update to match. - Another fix for our pkey handling of PROT_EXEC mappings. - A fix for a crash when booting a "secure VM" under an ultravisor with certain numbers of CPUs. Thanks to: Aneesh Kumar K.V, Haren Myneni, Laurent Dufour, Sandipan Das, Satheesh Rajendran, Thiago Jung Bauermann" * tag 'powerpc-5.8-7' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: selftests/powerpc: Use proper error code to check fault address powerpc/vas: Report proper error code for address translation failure powerpc/pseries/svm: Fix incorrect check for shared_lppaca_size powerpc/book3s64/pkeys: Fix pkey_access_permitted() for execute disable pkey
2020-07-18x86/ioperm: Fix io bitmap invalidation on Xen PVAndy Lutomirski
tss_invalidate_io_bitmap() wasn't wired up properly through the pvop machinery, so the TSS and Xen's io bitmap would get out of sync whenever disabling a valid io bitmap. Add a new pvop for tss_invalidate_io_bitmap() to fix it. This is XSA-329. Fixes: 22fe5b0439dd ("x86/ioperm: Move TSS bitmap update to exit to user work") Signed-off-by: Andy Lutomirski <luto@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Juergen Gross <jgross@suse.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/d53075590e1f91c19f8af705059d3ff99424c020.1595030016.git.luto@kernel.org
2020-07-18media: atomisp: move CCK endpoint address to generic headerAndy Shevchenko
IOSF MBI header contains a lot of definitions, such as end point addresses of IPs. Move CCK address from AtomISP driver to generic header. While here, drop unused one. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-07-17Merge tag 'arm-fixes-5.8-2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc into master Pull ARM SoC fixes from Arnd Bergmann: "This time there are a number of actual code fixes, plus a small set of device tree issues getting addressed: Renesas: - one defconfig cleanup to allow a later Kconfig change Intel socfpga: - enable QSPI devices on some machines - fix DTC validation warnings TI OMAP: - Two DEBUG_ATOMIC_SLEEP fixes for ti-sysc interconnect target module driver - A regression fix for ti-sysc no-idle handling that caused issues compared to earlier platform data based booting - A fix for memory leak for omap_hwmod_allocate_module - Fix d_can driver probe for am437x NXP i.MX: - A couple of fixes on i.MX platform device registration code to stop the use of invalid IRQ 0. - Fix a regression seen on ls1021a platform, caused by commit 52102a3ba6a61 ("soc: imx: move cpu code to drivers/soc/imx"). - Fix a misconfiguration of audio SSI on imx6qdl-gw551x board. Amlogic Meson: - misc DT fixes - SoC ID fixes to detect all chips correctly" * tag 'arm-fixes-5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: arm64: dts: spcfpga: Align GIC, NAND and UART nodenames with dtschema ARM: dts: socfpga: Align L2 cache-controller nodename with dtschema arm64: dts: stratix10: increase QSPI reg address in nand dts file arm64: dts: stratix10: add status to qspi dts node arm64: dts: agilex: add status to qspi dts node ARM: dts: Fix dcan driver probe failed on am437x platform ARM: OMAP2+: Fix possible memory leak in omap_hwmod_allocate_module arm64: defconfig: Enable CONFIG_PCIE_RCAR_HOST soc: imx: check ls1021a ARM: imx: Remove imx_add_imx_dma() unused irq_err argument ARM: imx: Provide correct number of resources when registering gpio devices ARM: dts: imx6qdl-gw551x: fix audio SSI bus: ti-sysc: Do not disable on suspend for no-idle bus: ti-sysc: Fix sleeping function called from invalid context for RTC quirk bus: ti-sysc: Fix wakeirq sleeping function called from invalid context ARM: dts: meson: Align L2 cache-controller nodename with dtschema arm64: dts: meson-gxl-s805x: reduce initial Mali450 core frequency arm64: dts: meson: add missing gxl rng clock soc: amlogic: meson-gx-socinfo: Fix S905X3 and S905D3 ID's
2020-07-17Merge tag 'arm64-fixes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux into master Pull arm64 fixes from Will Deacon: "A batch of arm64 fixes. Although the diffstat is a bit larger than we'd usually have at this stage, a decent amount of it is the addition of comments describing our syscall tracing behaviour, and also a sweep across all the modular arm64 PMU drivers to make them rebust against unloading and unbinding. There are a couple of minor things kicking around at the moment (CPU errata and module PLTs for very large modules), but I'm not expecting any significant changes now for us in 5.8. - Fix kernel text addresses for relocatable images booting using EFI and with KASLR disabled so that they match the vmlinux ELF binary. - Fix unloading and unbinding of PMU driver modules. - Fix generic mmiowb() when writeX() is called from preemptible context (reported by the riscv folks). - Fix ptrace hardware single-step interactions with signal handlers, system calls and reverse debugging. - Fix reporting of 64-bit x0 register for 32-bit tasks via 'perf_regs'. - Add comments describing syscall entry/exit tracing ABI" * tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: drivers/perf: Prevent forced unbinding of PMU drivers asm-generic/mmiowb: Allow mmiowb_set_pending() when preemptible() arm64: Use test_tsk_thread_flag() for checking TIF_SINGLESTEP arm64: ptrace: Use NO_SYSCALL instead of -1 in syscall_trace_enter() arm64: syscall: Expand the comment about ptrace and syscall(-1) arm64: ptrace: Add a comment describing our syscall entry/exit trap ABI arm64: compat: Ensure upper 32 bits of x0 are zero on syscall return arm64: ptrace: Override SPSR.SS when single-stepping is enabled arm64: ptrace: Consistently use pseudo-singlestep exceptions drivers/perf: Fix kernel panic when rmmod PMU modules during perf sampling efi/libstub/arm64: Retain 2MB kernel Image alignment if !KASLR
2020-07-17genirq/affinity: Handle affinity setting on inactive interrupts correctlyThomas Gleixner
Setting interrupt affinity on inactive interrupts is inconsistent when hierarchical irq domains are enabled. The core code should just store the affinity and not call into the irq chip driver for inactive interrupts because the chip drivers may not be in a state to handle such requests. X86 has a hacky workaround for that but all other irq chips have not which causes problems e.g. on GIC V3 ITS. Instead of adding more ugly hacks all over the place, solve the problem in the core code. If the affinity is set on an inactive interrupt then: - Store it in the irq descriptors affinity mask - Update the effective affinity to reflect that so user space has a consistent view - Don't call into the irq chip driver This is the core equivalent of the X86 workaround and works correctly because the affinity setting is established in the irq chip when the interrupt is activated later on. Note, that this is only effective when hierarchical irq domains are enabled by the architecture. Doing it unconditionally would break legacy irq chip implementations. For hierarchial irq domains this works correctly as none of the drivers can have a dependency on affinity setting in inactive state by design. Remove the X86 workaround as it is not longer required. Fixes: 02edee152d6e ("x86/apic/vector: Ignore set_affinity call for inactive interrupts") Reported-by: Ali Saidi <alisaidi@amazon.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Ali Saidi <alisaidi@amazon.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20200529015501.15771-1-alisaidi@amazon.com Link: https://lkml.kernel.org/r/877dv2rv25.fsf@nanos.tec.linutronix.de
2020-07-17RISC-V: Upgrade smp_mb__after_spinlock() to iorw,iorwPalmer Dabbelt
While digging through the recent mmiowb preemption issue it came up that we aren't actually preventing IO from crossing a scheduling boundary. While it's a bit ugly to overload smp_mb__after_spinlock() with this behavior, it's what PowerPC is doing so there's some precedent. Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
2020-07-17Merge tag 'socfpga_fixes_for_v5.8_v2' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into arm/fixes arm/arm64: dts: socfpga: fixes for v5.8 - Add status = "okay" in QSPI - Increase QSPI size in reg property - Fix dtschema for SoCFPGA platforms * tag 'socfpga_fixes_for_v5.8_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux: arm64: dts: spcfpga: Align GIC, NAND and UART nodenames with dtschema ARM: dts: socfpga: Align L2 cache-controller nodename with dtschema arm64: dts: stratix10: increase QSPI reg address in nand dts file arm64: dts: stratix10: add status to qspi dts node arm64: dts: agilex: add status to qspi dts node Link: https://lore.kernel.org/r/20200717155758.18233-1-dinguyen@kernel.org Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2020-07-17Merge tag 'renesas-fixes-for-v5.8-tag1' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/fixes Renesas fixes for v5.8 - Replace CONFIG_PCIE_RCAR by CONFIG_PCIE_RCAR_HOST in the defconfig, to unblock a planned Kconfig change. * tag 'renesas-fixes-for-v5.8-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: arm64: defconfig: Enable CONFIG_PCIE_RCAR_HOST Link: https://lore.kernel.org/r/20200717100523.15418-1-geert+renesas@glider.be Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2020-07-16Merge tag 'omap-for-v5.8/fixes-rc5-signed' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes Fixes for omaps for v5.8-rc cycle Few fixes for issues noticed during testing: - Two DEBUG_ATOMIC_SLEEP fixes for ti-sysc interconnect target module driver - A regression fix for ti-sysc no-idle handling that caused issues compared to earlier platform data based booting - A fix for memory leak for omap_hwmod_allocate_module - Fix d_can driver probe for am437x * tag 'omap-for-v5.8/fixes-rc5-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: ARM: dts: Fix dcan driver probe failed on am437x platform ARM: OMAP2+: Fix possible memory leak in omap_hwmod_allocate_module bus: ti-sysc: Do not disable on suspend for no-idle bus: ti-sysc: Fix sleeping function called from invalid context for RTC quirk bus: ti-sysc: Fix wakeirq sleeping function called from invalid context Link: https://lore.kernel.org/r/pull-1594840100-132735@atomide.com Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2020-07-16Merge tag 'imx-fixes-5.8-2' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes i.MX fixes for 5.8, round 2: - A couple of fixes on i.MX platform device registration code to stop the use of invalid IRQ 0. - Fix a regression seen on ls1021a platform, caused by commit 52102a3ba6a61 ("soc: imx: move cpu code to drivers/soc/imx"). - Fix a misconfiguration of audio SSI on imx6qdl-gw551x board. * tag 'imx-fixes-5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: soc: imx: check ls1021a ARM: imx: Remove imx_add_imx_dma() unused irq_err argument ARM: imx: Provide correct number of resources when registering gpio devices ARM: dts: imx6qdl-gw551x: fix audio SSI Link: https://lore.kernel.org/r/20200714145649.GP15718@dragon Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2020-07-16Merge tag 'amlogic-fixes' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/fixes Amlogic fixes for v5.8-rc - misc DT fixes, and SoC ID fixes * tag 'amlogic-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic: ARM: dts: meson: Align L2 cache-controller nodename with dtschema arm64: dts: meson-gxl-s805x: reduce initial Mali450 core frequency arm64: dts: meson: add missing gxl rng clock soc: amlogic: meson-gx-socinfo: Fix S905X3 and S905D3 ID's Link: https://lore.kernel.org/r/7hk0zc1ujc.fsf@baylibre.com Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2020-07-16x86: math-emu: Fix up 'cmp' insn for clang iasArnd Bergmann
The clang integrated assembler requires the 'cmp' instruction to have a length prefix here: arch/x86/math-emu/wm_sqrt.S:212:2: error: ambiguous instructions require an explicit suffix (could be 'cmpb', 'cmpw', or 'cmpl') cmp $0xffffffff,-24(%ebp) ^ Make this a 32-bit comparison, which it was clearly meant to be. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Link: https://lkml.kernel.org/r/20200527135352.1198078-1-arnd@arndb.de
2020-07-16x86/entry: Fix vectors to IDTENTRY_SYSVEC for CONFIG_HYPERVSedat Dilek
When assembling with Clang via `make LLVM_IAS=1` and CONFIG_HYPERV enabled, we observe the following error: <instantiation>:9:6: error: expected absolute expression .if HYPERVISOR_REENLIGHTENMENT_VECTOR == 3 ^ <instantiation>:1:1: note: while in macro instantiation idtentry HYPERVISOR_REENLIGHTENMENT_VECTOR asm_sysvec_hyperv_reenlightenment sysvec_hyperv_reenlightenment has_error_code=0 ^ ./arch/x86/include/asm/idtentry.h:627:1: note: while in macro instantiation idtentry_sysvec HYPERVISOR_REENLIGHTENMENT_VECTOR sysvec_hyperv_reenlightenment; ^ <instantiation>:9:6: error: expected absolute expression .if HYPERVISOR_STIMER0_VECTOR == 3 ^ <instantiation>:1:1: note: while in macro instantiation idtentry HYPERVISOR_STIMER0_VECTOR asm_sysvec_hyperv_stimer0 sysvec_hyperv_stimer0 has_error_code=0 ^ ./arch/x86/include/asm/idtentry.h:628:1: note: while in macro instantiation idtentry_sysvec HYPERVISOR_STIMER0_VECTOR sysvec_hyperv_stimer0; This is caused by typos in arch/x86/include/asm/idtentry.h: HYPERVISOR_REENLIGHTENMENT_VECTOR -> HYPERV_REENLIGHTENMENT_VECTOR HYPERVISOR_STIMER0_VECTOR -> HYPERV_STIMER0_VECTOR For more details see ClangBuiltLinux issue #1088. Fixes: a16be368dd3f ("x86/entry: Convert various hypervisor vectors to IDTENTRY_SYSVEC") Suggested-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Sedat Dilek <sedat.dilek@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Wei Liu <wei.liu@kernel.org> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Link: https://github.com/ClangBuiltLinux/linux/issues/1088 Link: https://github.com/ClangBuiltLinux/linux/issues/1043 Link: https://lore.kernel.org/patchwork/patch/1272115/ Link: https://lkml.kernel.org/r/20200714194740.4548-1-sedat.dilek@gmail.com
2020-07-16x86/entry: Add compatibility with IASJian Cai
Clang's integrated assembler does not allow symbols with non-absolute values to be reassigned. Modify the interrupt entry loop macro to be compatible with IAS by using a label and an offset. Reported-by: Nick Desaulniers <ndesaulniers@google.com> Reported-by: Sedat Dilek <sedat.dilek@gmail.com> Suggested-by: Nick Desaulniers <ndesaulniers@google.com> Suggested-by: Brian Gerst <brgerst@gmail.com> Suggested-by: Arvind Sankar <nivedita@alum.mit.edu> Signed-off-by: Jian Cai <caij2003@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Sedat Dilek <sedat.dilek@gmail.com> # Link: https://github.com/ClangBuiltLinux/linux/issues/1043 Link: https://lkml.kernel.org/r/20200714233024.1789985-1-caij2003@gmail.com
2020-07-16arm64: Use test_tsk_thread_flag() for checking TIF_SINGLESTEPWill Deacon
Rather than open-code test_tsk_thread_flag() at each callsite, simply replace the couple of offenders with calls to test_tsk_thread_flag() directly. Signed-off-by: Will Deacon <will@kernel.org>
2020-07-16arm64: ptrace: Use NO_SYSCALL instead of -1 in syscall_trace_enter()Will Deacon
Setting a system call number of -1 is special, as it indicates that the current system call should be skipped. Use NO_SYSCALL instead of -1 when checking for this scenario, which is different from the -1 returned due to a seccomp failure. Cc: Mark Rutland <mark.rutland@arm.com> Cc: Keno Fischer <keno@juliacomputing.com> Cc: Luis Machado <luis.machado@linaro.org> Signed-off-by: Will Deacon <will@kernel.org>
2020-07-16arm64: syscall: Expand the comment about ptrace and syscall(-1)Will Deacon
If a task executes syscall(-1), we intercept this early and force x0 to be -ENOSYS so that we don't need to distinguish this scenario from one where the scno is -1 because a tracer wants to skip the system call using ptrace. With the return value set, the return path is the same as the skip case. Although there is a one-line comment noting this in el0_svc_common(), it misses out most of the detail. Expand the comment to describe a bit more about what is going on. Cc: Mark Rutland <mark.rutland@arm.com> Cc: Keno Fischer <keno@juliacomputing.com> Cc: Luis Machado <luis.machado@linaro.org> Signed-off-by: Will Deacon <will@kernel.org>
2020-07-16arm64: ptrace: Add a comment describing our syscall entry/exit trap ABIWill Deacon
Our tracehook logic for syscall entry/exit raises a SIGTRAP back to the tracer following a ptrace request such as PTRACE_SYSCALL. As part of this procedure, we clobber the reported value of one of the tracee's general purpose registers (x7 for native tasks, r12 for compat) to indicate whether the stop occurred on syscall entry or exit. This is a slightly unfortunate ABI, as it prevents the tracer from accessing the real register value and is at odds with other similar stops such as seccomp traps. Since we're stuck with this ABI, expand the comment in our tracehook logic to acknowledge the issue and describe the behaviour in more detail. Cc: Mark Rutland <mark.rutland@arm.com> Cc: Luis Machado <luis.machado@linaro.org> Reported-by: Keno Fischer <keno@juliacomputing.com> Signed-off-by: Will Deacon <will@kernel.org>
2020-07-16arm64: compat: Ensure upper 32 bits of x0 are zero on syscall returnWill Deacon
Although we zero the upper bits of x0 on entry to the kernel from an AArch32 task, we do not clear them on the exception return path and can therefore expose 64-bit sign extended syscall return values to userspace via interfaces such as the 'perf_regs' ABI, which deal exclusively with 64-bit registers. Explicitly clear the upper 32 bits of x0 on return from a compat system call. Cc: <stable@vger.kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Keno Fischer <keno@juliacomputing.com> Cc: Luis Machado <luis.machado@linaro.org> Signed-off-by: Will Deacon <will@kernel.org>
2020-07-16arm64: ptrace: Override SPSR.SS when single-stepping is enabledWill Deacon
Luis reports that, when reverse debugging with GDB, single-step does not function as expected on arm64: | I've noticed, under very specific conditions, that a PTRACE_SINGLESTEP | request by GDB won't execute the underlying instruction. As a consequence, | the PC doesn't move, but we return a SIGTRAP just like we would for a | regular successful PTRACE_SINGLESTEP request. The underlying problem is that when the CPU register state is restored as part of a reverse step, the SPSR.SS bit is cleared and so the hardware single-step state can transition to the "active-pending" state, causing an unexpected step exception to be taken immediately if a step operation is attempted. In hindsight, we probably shouldn't have exposed SPSR.SS in the pstate accessible by the GPR regset, but it's a bit late for that now. Instead, simply prevent userspace from configuring the bit to a value which is inconsistent with the TIF_SINGLESTEP state for the task being traced. Cc: <stable@vger.kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Keno Fischer <keno@juliacomputing.com> Link: https://lore.kernel.org/r/1eed6d69-d53d-9657-1fc9-c089be07f98c@linaro.org Reported-by: Luis Machado <luis.machado@linaro.org> Tested-by: Luis Machado <luis.machado@linaro.org> Signed-off-by: Will Deacon <will@kernel.org>
2020-07-16arm64: ptrace: Consistently use pseudo-singlestep exceptionsWill Deacon
Although the arm64 single-step state machine can be fast-forwarded in cases where we wish to generate a SIGTRAP without actually executing an instruction, this has two major limitations outside of simply skipping an instruction due to emulation. 1. Stepping out of a ptrace signal stop into a signal handler where SIGTRAP is blocked. Fast-forwarding the stepping state machine in this case will result in a forced SIGTRAP, with the handler reset to SIG_DFL. 2. The hardware implicitly fast-forwards the state machine when executing an SVC instruction for issuing a system call. This can interact badly with subsequent ptrace stops signalled during the execution of the system call (e.g. SYSCALL_EXIT or seccomp traps), as they may corrupt the stepping state by updating the PSTATE for the tracee. Resolve both of these issues by injecting a pseudo-singlestep exception on entry to a signal handler and also on return to userspace following a system call. Cc: <stable@vger.kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Tested-by: Luis Machado <luis.machado@linaro.org> Reported-by: Keno Fischer <keno@juliacomputing.com> Signed-off-by: Will Deacon <will@kernel.org>
2020-07-16arm64: dts: allwinner: h6: Fix Cedrus IOMMU usageMaxime Ripard
Now that the IOMMU driver has been introduced, it prevents any access from a DMA master going through it that hasn't properly mapped the pages, and that link is set up through the iommus property. Unfortunately we forgot to add that property to the video engine node when adding the IOMMU node, so now any DMA access is broken. Fixes: b3a0a2f910c7 ("arm64: dts: allwinner: h6: Add IOMMU") Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20200628180804.79026-1-maxime@cerno.tech
2020-07-15arm64: dts: spcfpga: Align GIC, NAND and UART nodenames with dtschemaKrzysztof Kozlowski
Fix dtschema validator warnings like: intc@fffc1000: $nodename:0: 'intc@fffc1000' does not match '^interrupt-controller(@[0-9a-f,]+)*$' Fixes: 78cd6a9d8e15 ("arm64: dts: Add base stratix 10 dtsi") Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
2020-07-15ARM: dts: socfpga: Align L2 cache-controller nodename with dtschemaKrzysztof Kozlowski
Fix dtschema validator warnings like: l2-cache@fffff000: $nodename:0: 'l2-cache@fffff000' does not match '^(cache-controller|cpu)(@[0-9a-f,]+)*$' Fixes: 475dc86d08de ("arm: dts: socfpga: Add a base DTSI for Altera's Arria10 SOC") Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
2020-07-15arm64: dts: stratix10: increase QSPI reg address in nand dts fileDinh Nguyen
Match the QSPI reg address in the socfpga_stratix10_socdk.dts file. Fixes: 80f132d73709 ("arm64: dts: increase the QSPI reg address for Stratix10 and Agilex") Cc: linux-stable <stable@vger.kernel.org> # >= v5.6 Signed-off-by: Dinh Nguyen <dinh.nguyen@intel.com>
2020-07-15arm64: dts: stratix10: add status to qspi dts nodeDinh Nguyen
Add status = "okay" to QSPI node. Fixes: 0cb140d07fc75 ("arm64: dts: stratix10: Add QSPI support for Stratix10") Cc: linux-stable <stable@vger.kernel.org> # >= v5.6 Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
generated by cgit (git 2.34.1) at 2024-06-17 06:44:04 +0000