| Age | Commit message (Collapse) | Author |
|---|
|
|
|
Based on two separate cleanup branches, it's now empty and can be removed.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Stephen Warren <swarren@wwwdotorg.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc
From Stepen Warren:
ARM: tegra: add Tegra114 SoC support
This pull request adds initial support for the Tegra114 SoC, which
integrates a quad-core ARM Cortex-A15 CPU. I'm proud to observe that we
posted the initial versions of these patches before the final official
announcement of this chip.
These patches are enough to boot with a UART-based console, support the
Dalmore and Pluto reference/evaluation boards, instantiate the GPIO and
pinctrl drivers, and enable a cpuidle state. As yet, no clocks or
storage devices are supported, but patches for those will follow shortly.
This pull request is based on (most of) the previous pull request with
tag tegra-for-3.9-soc-cpuidle, followed by a merge of the previous pull
request with tag tegra-for-3.9-scu-base-rework.
* tag 'tegra-for-3.9-soc-t114' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (24 commits)
ARM: DT: tegra114: add pinmux DT entry
ARM: DT: tegra114: add GPIO DT entry
ARM: tegra114: select PINCTRL for Tegra114 SoC
ARM: tegra: add Tegra114 ARM_CPUIDLE_WFI_STATE support
ARM: tegra: Add SMMU entry to Tegra114 DT
ARM: tegra: add AHB entry to Tegra114 DT
ARM: tegra: Add initial support for Tegra114 SoC.
ARM: dt: tegra114: Add new board, Pluto
ARM: dt: tegra114: Add new board, Dalmore
ARM: dt: tegra114: Add new SoC base, Tegra114 SoC
ARM: tegra: fuse: Add chip ID Tegra114 0x35
ARM: OMAP: Make use of available scu_a9_get_base() interface
ARM: tegra: Skip scu_enable(scu_base) if not Cortex A9
ARM: Add API to detect SCU base address from CP15
ARM: tegra: Use DT /cpu node to detect number of CPU core
ARM: tegra: Add CPU nodes to Tegra30 device tree
ARM: tegra: Add CPU nodes to Tegra20 device tree
ARM: perf: simplify __hw_perf_event_init err handling
ARM: perf: remove unnecessary checks for idx < 0
ARM: perf: handle armpmu_register failing
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Remove/add conflict in arch/arm/mach-tegra/common.c resolved.
Remove/remove conflict in arch/arm/mach-tegra/platsmp.c. Leave the empty
stub function for now since removing it in the merge commit is confusing;
will be cleaned up in a separate commit. # # It looks like you may be
committing a merge. # If this is not correct, please remove the file #
.git/MERGE_HEAD # and try again.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc
From Stephen Warren:
ARM: tegra: cpuidle enhancements
This pull request implements a new "LP2" cpuidle state for Tegra20,
which makes use of the couple cpuidle feature.
It is based on (most of) the previous pull request, with tag
tegra-for-3.9-soc-usb.
* tag 'tegra-for-3.9-soc-cpuidle' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: tegra20: cpuidle: apply coupled cpuidle for powered-down mode
ARM: tegra20: flowctrl: add support for cpu_suspend_enter/exit
clk: tegra20: Implementing CPU low-power function for tegra_cpu_car_ops
ARM: tegra20: cpuidle: add powered-down state for secondary CPU
ARM: tegra: add pending SGI checking API
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc
From Stephen Warren:
ARM: tegra: USB driver cleanup
The Tegra USB driver has a number of issues:
1) The PHY driver isn't a true platform device, and doesn't implement
the standard USB PHY API.
2) struct device instance numbers were used to make decisions in the
driver, rather than being parameterized by DT or platform data.
This pull request solves issue (2), and lays the groundwork for solving
issue (1). The work on issue (1) involved introducing new DT nodes for
the USB PHYs, which in turn interacted with the Tegra common clock
framework changes, due to the move of clock lookups into device tree.
Hence, these USB driver changes are taken through the Tegra tree with
acks from USB maintainers.
This pull request is based on the previous pull request, with tag
tegra-for-3.9-soc-ccf.
* tag 'tegra-for-3.9-soc-usb' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
usb: host: tegra: make use of PHY pointer of HCD
ARM: tegra: Add reset GPIO information to PHY DT node
usb: host: tegra: don't touch EMC clock
usb: add APIs to access host registers from Tegra PHY
USB: PHY: tegra: Get rid of instance number to differentiate PHY type
USB: PHY: tegra: get rid of instance number to differentiate legacy controller
ARM: tegra: add clocks properties to USB PHY nodes
ARM: tegra: add DT nodes for Tegra USB PHY
usb: phy: remove unused APIs from Tegra PHY.
usb: host: tegra: Resetting PORT0 based on information received via DT.
ARM: tegra: Add new DT property to USB node.
usb: phy: use kzalloc to allocate struct tegra_usb_phy
ARM: tegra: remove USB address related macros from iomap.h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc
From Stephen Warren:
ARM: tegra: Common Clock Framework rework
Tegra already supports the common clock framework, but had issues:
1) The clock driver was located in arch/arm/mach-tegra/ rather than
drivers/clk/.
2) A single "Tegra clock" type was implemented, rather than separate
clock types for PLL, mux, divider, ... type in HW.
3) Clock lookups by device drivers were still driven by device name
and connection ID, rather than through device tree.
This pull request solves all three issues. This required some DT changes
to add clocks properties, and driver changes to request clocks more
"correctly". Finally, this rework allows all AUXDATA to be removed from
Tegra board files, and various duplicate clock lookup entries to be
removed from the driver.
This pull request is based on the previous pull request, with tag
tegra-for-3.9-cleanup.
* tag 'tegra-for-3.9-soc-ccf' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (31 commits)
clk: tegra30: remove unused TEGRA_CLK_DUPLICATE()s
clk: tegra20: remove unused TEGRA_CLK_DUPLICATE()s
ARM: tegra30: remove auxdata
ARM: tegra20: remove auxdata
ASoC: tegra: remove auxdata
staging: nvec: remove use of clk_get_sys
ARM: tegra: paz00: add clock information to DT
ARM: tegra: add clock properties to Tegra30 DT
ARM: tegra: add clock properties to Tegra20 DT
spi: tegra: do not use clock name to get clock
ARM: tegra: remove legacy clock code
ARM: tegra: migrate to new clock code
clk: tegra: add clock support for Tegra30
clk: tegra: add clock support for Tegra20
clk: tegra: add Tegra specific clocks
ARM: tegra: define Tegra30 CAR binding
ARM: tegra: define Tegra20 CAR binding
ARM: tegra: move tegra_cpu_car.h to linux/clk/tegra.h
ARM: tegra: add function to read chipid
ARM: tegra: fix compile error when disable CPU_IDLE
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/mach-tegra/board-dt-tegra20.c
arch/arm/mach-tegra/board-dt-tegra30.c
arch/arm/mach-tegra/common.c
arch/arm/mach-tegra/platsmp.c
drivers/clocksource/Makefile
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
From Simon Horman:
Third round of Renesas ARM-based SoC changes for v3.9
A fix for r8a7779 clocks.
* tag 'renesas-soc3-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7779: Correct TMU clock support
|
|
The Nomadik Device Tree patch series accidentally
selected OF instead of USE_OF which led to problems
during compile:
arch/arm/kernel/devtree.c: In function 'arm_dt_memblock_reserve':
/home/elinwal/linux-arm-soc/arch/arm/kernel/devtree.c:43:7: error: 'initial_boot_params' undeclared (first use in this function)
(etc).
This fixes it up by selecting USE_OF instead.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Linux 3.8-rc6
|
|
into next/soc
From Jason Cooper:
mvebu drivers for v3.9
- use rtc-mv in mvebu armv7 SoCs
- add pci-e hotplug for kirkwood
Depends on:
- tags/mvebu_fixes_for_v3.8-rc6
* tag 'drivers_for_v3.9' of git://git.infradead.org/users/jcooper/linux:
cpuidle: kirkwood: Move out of mach directory
rtc: Add support of rtc-mv for MVEBU SoCs
ARM: Kirkwood: Support basic hotplug for PCI-E
arm: mvebu: i2c come back in defconfig
arm: plat-orion: fix printing of "MPP config unavailable on this hardware"
Dove: activate GPIO interrupts in DT
|
|
Linux 3.8-rc6
|
|
git://git.linaro.org/people/shawnguo/linux-2.6 into next/soc
From Shawn Guo:
imx6q cpuidle support for 3.9
- It's based on imx-cleanup-3.9 to avoid conflicts.
* tag 'imx6q-cpudile-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx6q: support WAIT mode using cpuidle
ARM: imx: move imx6q_cpuidle_driver into a separate file
ARM: imx: mask gpc interrupts initially
ARM: imx: return zero in case next event gets a large increment
ARM: imx: Remove mx508 support
ARM: imx: Remove mach-mx51_3ds board
ARM: imx: use debug_ll_io_init() for imx6q
ARM: imx: remove unused imx6q_clock_map_io()
ARM: mach-imx: Kconfig: Do not select Babbage for MACH_IMX51_DT
Signed-off-by: Olof Johansson <olof@lixom.net>
Still, two delete/change conflicts caused by imx/cleanup:
arch/arm/mach-imx/mach-mx50_rdp.c
arch/arm/mach-imx/mach-mx51_3ds.c
|
|
Fix the issue:
tree: git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc.git next/soc
head: 6ed05a2aab3763b58922247543d7079106b254dc
commit: af70fdc947dbe835acc26c6ee9e8e930f38935f8 [4/8] Merge branch 'marco-timer-cleanup-rebase' of
git://gitorious.org/sirfprima2-kernel/sirfprima2-kernel into next/soc
config: make ARCH=arm prima2_defconfig
All error/warnings:
>> arch/arm/mach-prima2/platsmp.c:20:30: fatal error: asm/hardware/gic.h: No such file or directory
compilation terminated.
--
>> arch/arm/mach-prima2/common.c:15:30: fatal error: asm/hardware/gic.h: No such file or directory
compilation terminated.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Cc: Xie ChanglongX <changlongx.xie@intel.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
During code review it was noticed that the clock value for
TMU01 was incorrect and the value for TMU02 was missing.
For reference: As of 3.8-rc6 there are no in-tree consumes of these clocks.
Reported-by: Denis Oliver Kropp <dok@directfb.org>
Reviewed-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
From Simon Horman:
Second round of Renesas ARM-based SoC changes for v3.9
* Changes to allow unplugging of CPU0 by Ulrich Hecht.
* Changes to add reg and device_type properties to cpus
device trees entries by Simon Horman.
* tag 'renesas-soc2-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: mach-shmobile: sh73a0: allow unplugging of CPU0
ARM: mach-shmobile: add shmobile_cpu_disable_any()
ARM: mach-shmobile: emev2: Add reg and device_type properties to cpus
ARM: mach-shmobile: sh73a0: Add reg and device_type properties to cpus
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Pull MIPS updates from Ralf Baechle:
"A number of fixes all across the MIPS tree. No area is particularly
standing out and things have cooled down quite nicely for a release."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Function tracer: Fix broken function tracing
mips: Move __virt_addr_valid() to a place for MIPS 64
MIPS: Netlogic: Fix UP compilation on XLR
MIPS: AR71xx: Fix AR71XX_PCI_MEM_SIZE
MIPS: AR724x: Fix AR724X_PCI_MEM_SIZE
MIPS: Lantiq: Fix cp0_perfcount_irq mapping
MIPS: DSP: Fix DSP mask for registers.
MIPS: Fix build failure by adding definition of pfn_pmd().
MIPS: Octeon: Fix warning.
MIPS: delay.c: Check BITS_PER_LONG instead of __SIZEOF_LONG__
MIPS: PNX833x: Fix comment.
MIPS: Add struct p_format to union mips_instruction.
MIPS: Export <asm/break.h>.
MIPS: BCM47xx: Enable SSB prerequisite SSB_DRIVER_PCICORE.
MIPS: BCM47xx: Select GPIOLIB for BCMA on bcm47xx platform
MIPS: vpe.c: Fix null pointer dereference in print arguments.
|
|
Move the Kirkwood cpuidle driver out of arch/arm/mach-kirkwood and
into drivers/cpuidle. Convert the driver into a platform driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Function tracing is currently broken for all 32 bit MIPS platforms.
When tracing is enabled, the kernel immediately hangs on boot.
This is a result of commit b732d439cb43336cd6d7e804ecb2c81193ef63b0
that changes the kernel/trace/Kconfig file so that is no longer
forces FRAME_POINTER when FUNCTION_TRACING is enabled.
MIPS frame pointers are generally considered to be useless because
they cannot be used to unwind the stack. Unfortunately the MIPS
function tracing code has bugs that are masked by the use of frame
pointers. This commit fixes the bugs so that MIPS frame pointers
don't need to be enabled.
The bugs are a result of the odd calling sequence used to call the trace
routine. This calling sequence is inserted into every traceable function
when the tracing CONFIG option is enabled. This sequence is generated
for 32bit MIPS platforms by the compiler via the "-pg" flag.
Part of the sequence is "addiu sp,sp,-8" in the delay slot after every
call to the trace routine "_mcount" (some legacy thing where 2 arguments
used to be pushed on the stack). The _mcount routine is expected to
adjust the sp by +8 before returning. So when not disabled, the original
jalr and addiu will be there, so _mcount has to adjust sp.
The problem is that when tracing is disabled for a function, the
"jalr _mcount" instruction is replaced with a nop, but the
"addiu sp,sp,-8" is still executed and the stack pointer is left
trashed. When frame pointers are enabled the problem is masked
because any access to the stack is done through the frame
pointer and the stack pointer is restored from the frame pointer when
the function returns.
This patch writes two nops starting at the address of the "jalr _mcount"
instruction whenever tracing is disabled. This means that the
"addiu sp,sp.-8" will be converted to a nop along with the "jalr". When
disabled, there will be two nops.
This is SMP safe because the first time this happens is during
ftrace_init() which is before any other processor has been started.
Subsequent calls to enable/disable tracing when other CPUs ARE running
will still be safe because the enable will only change the first nop
to a "jalr" and the disable, while writing 2 nops, will only be changing
the "jalr". This patch also stops using stop_machine() to call the
tracer enable/disable routines and calls them directly because the
routines are SMP safe.
When the kernel first boots we have to be able to handle the gcc
generated jalr, addui sequence until ftrace_init gets a chance to run
and change the sequence. At this point mcount just adjusts the stack
and returns. When ftrace_init runs, we convert the jalr/addui to nops.
Then whenever tracing is enabled we convert the first nop to a "jalr
mcount+8". The mcount+8 entry point skips the stack adjust.
[ralf@linux-mips.org: Folded in Steven Rostedt's build fix.]
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Cc: rostedt@goodmis.org
Cc: ddaney.cavm@gmail.com
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/4806/
Patchwork: https://patchwork.linux-mips.org/patch/4841/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Commit d3ce88431892 "MIPS: Fix modpost error in modules attepting to use
virt_addr_valid()" moved __virt_addr_valid() from a macro in a header
file to a function in ioremap.c. But ioremap.c is only compiled for MIPS
32, and not for MIPS 64.
When compiling for my yeeloong2, which supposedly supports hibernation,
which compiles kernel/power/snapshot.c which calls virt_addr_valid(), I
got this error:
LD init/built-in.o
kernel/built-in.o: In function `memory_bm_free':
snapshot.c:(.text+0x4c9c4): undefined reference to `__virt_addr_valid'
snapshot.c:(.text+0x4ca58): undefined reference to `__virt_addr_valid'
kernel/built-in.o: In function `snapshot_write_next':
(.text+0x4e44c): undefined reference to `__virt_addr_valid'
kernel/built-in.o: In function `snapshot_write_next':
(.text+0x4e890): undefined reference to `__virt_addr_valid'
make[1]: *** [vmlinux] Error 1
make: *** [sub-make] Error 2
I suspect that __virt_addr_valid() is fine for mips 64. I moved it to
mmap.c such that it gets compiled for mips 64 and 32.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4842/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 EFI fixes from Peter Anvin:
"This is a collection of fixes for the EFI support. The controversial
bit here is a set of patches which bumps the boot protocol version as
part of fixing some serious problems with the EFI handover protocol,
used when booting under EFI using a bootloader as opposed to directly
from EFI. These changes should also make it a lot saner to support
cross-mode 32/64-bit EFI booting in the future. Getting these changes
into 3.8 means we avoid presenting an inconsistent ABI to bootloaders.
Other changes are display detection and fixing efivarfs."
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, efi: remove attribute check from setup_efi_pci
x86, build: Dynamically find entry points in compressed startup code
x86, efi: Fix PCI ROM handing in EFI boot stub, in 32-bit mode
x86, efi: Fix 32-bit EFI handover protocol entry point
x86, efi: Fix display detection in EFI boot stub
x86, boot: Define the 2.12 bzImage boot protocol
x86/boot: Fix minor fd leakage in tools/relocs.c
x86, efi: Set runtime_version to the EFI spec revision
x86, efi: fix 32-bit warnings in setup_efi_pci()
efivarfs: Delete dentry from dcache in efivarfs_file_write()
efivarfs: Never return ENOENT from firmware
efi, x86: Pass a proper identity mapping in efi_call_phys_prelog
efivarfs: Drop link count of the right inode
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
"This is a collection of miscellaneous fixes, the most important one is
the fix for the Samsung laptop bricking issue (auto-blacklisting the
samsung-laptop driver); the efi_enabled() changes you see below are
prerequisites for that fix.
The other issues fixed are booting on OLPC XO-1.5, an UV fix, NMI
debugging, and requiring CAP_SYS_RAWIO for MSR references, just as
with I/O port references."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
samsung-laptop: Disable on EFI hardware
efi: Make 'efi_enabled' a function to query EFI facilities
smp: Fix SMP function call empty cpu mask race
x86/msr: Add capabilities check
x86/dma-debug: Bump PREALLOC_DMA_DEBUG_ENTRIES
x86/olpc: Fix olpc-xo1-sci.c build errors
arch/x86/platform/uv: Fix incorrect tlb flush all issue
x86-64: Fix unwind annotations in recent NMI changes
x86-32: Start out cr0 clean, disable paging before modifying cr3/4
|
|
Various urgent EFI fixes and some warning cleanups for v3.8
* EFI boot stub fix for Macbook Pro's from Maarten Lankhorst
* Fix an oops in efivarfs from Lingzhu Xiang
* 32-bit warning cleanups from Jan Beulich
* Patch to Boot on >512GB RAM systems from Nathan Zimmer
* Set efi.runtime_version correctly
* efivarfs updates
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
The commit 2a37b1a "MIPS: Netlogic: Move from u32 cpumask to cpumask_t"
breaks uniprocessor compilation on XLR with:
arch/mips/netlogic/xlr/setup.c: In function 'prom_init':
arch/mips/netlogic/xlr/setup.c:196:6: error: unused variable 'i'
Fix by defining 'i' only when CONFIG_SMP is defined.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4760/
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The base address of the PCI memory is 0x10000000 and the base address of the
PCI configuration space is 0x17000000 on the AR71xx SoCs.
The AR71XX_PCI_MEM_SIZE is defined as 0x08000000 which is wrong because that
overlaps with the configuration space. This patch fixes the value of the
AR71XX_PCI_MEM_SIZE constant, in order to avoid this resource conflicts.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4873/
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The base address of the PCI memory is
0x10000000 and the base address of the
PCI configuration space is 0x14000000
on the AR724x SoCs.
The AR724X_PCI_MEM_SIZE is defined as
0x08000000 which is wrong because that
overlaps with the configuration space.
The patch fixes the value of the
AR724X_PCI_MEM_SIZE constant, in order
to avoid this resource conflicts.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4872/
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The introduction of the OF support broke the cp0_perfcount_irq mapping. This
resulted in oprofile not working anymore.
Offending commit is :
commit 3645da0276ae9f6938ff29b13904b803ecb68424
Author: John Crispin <blogic@openwrt.org>
Date: Tue Apr 17 10:18:32 2012 +0200
OF: MIPS: lantiq: implement irq_domain support
Signed-off-by: Conor O'Gorman <i@conorogorman.net>
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4875/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Unconditionally register the PCI-E bus, even if the link is currently
down. When the link is brought up the bus can be scanned through
/sys/bus/pci/rescan or otherwise. Since the HW has no interrupt for
link up, userspace will have to take care of the timing.
An earlier version of this was contingent on CONFIG_HOTPLUG, but
that is being removed from the kernel.
This also fixes printing the link up/down message to be displayed
on one line (structured logging broke this?)
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
fixes for v3.8-rc6
- add missing gpio interrupt lines to dove dt
- fix bad logic for printing MPP error message on orion boards
- build proper serial port driver after changing mvebu DT compatible property
- This is a change to mvebu_defconfig that I wouldn't usually push out as a
fix. However, the commit
b24212f arm: mvebu: Use dw-apb-uart instead of ns16650 as UART driver
changed the serial driver for the board in the dts file. without the patch
I've included in this pull, users won't see any log messages.
|
|
Originally 'efi_enabled' indicated whether a kernel was booted from
EFI firmware. Over time its semantics have changed, and it now
indicates whether or not we are booted on an EFI machine with
bit-native firmware, e.g. 64-bit kernel with 64-bit firmware.
The immediate motivation for this patch is the bug report at,
https://bugs.launchpad.net/ubuntu-cdimage/+bug/1040557
which details how running a platform driver on an EFI machine that is
designed to run under BIOS can cause the machine to become
bricked. Also, the following report,
https://bugzilla.kernel.org/show_bug.cgi?id=47121
details how running said driver can also cause Machine Check
Exceptions. Drivers need a new means of detecting whether they're
running on an EFI machine, as sadly the expression,
if (!efi_enabled)
hasn't been a sufficient condition for quite some time.
Users actually want to query 'efi_enabled' for different reasons -
what they really want access to is the list of available EFI
facilities.
For instance, the x86 reboot code needs to know whether it can invoke
the ResetSystem() function provided by the EFI runtime services, while
the ACPI OSL code wants to know whether the EFI config tables were
mapped successfully. There are also checks in some of the platform
driver code to simply see if they're running on an EFI machine (which
would make it a bad idea to do BIOS-y things).
This patch is a prereq for the samsung-laptop fix patch.
Cc: David Airlie <airlied@linux.ie>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Peter Jones <pjones@redhat.com>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Steve Langasek <steve.langasek@canonical.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Konrad Rzeszutek Wilk <konrad@kernel.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Add WAIT mode (ARM core clock gating) support to imx6q cpuidle driver.
As WAIT mode is broken on imx6q TO 1.0 and 1.1, it only enables the
support for revision 1.2 with chicken bit set.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Move imx6q_cpuidle_driver into a separate file as more codes will
be added when WAIT mode gets implemented as cpuidle.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Mask gpc interrupts initially to avoid suspicious interrupts.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The return of v2_set_next_event() will lead to an infinite loop in
tick_handle_oneshot_broadcast() - "goto again;" with imx6q WAIT mode
(to be enabled). This happens because when global event did not expire
any CPU local events, the broadcast device will be rearmed to a CPU
local next_event, which could be far away from now and result in a
max_delta_tick programming in set_next_event().
Fix the problem by detecting those next events with increments larger
than 0x7fffffff, and simply return zero in that case.
It leaves mx1_2_set_next_event() unchanged since only v2_set_next_event()
will be running with imx6q WAIT mode support.
Thanks Russell King for helping understand the problem.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
sh73a0 deals fine with disabling any core, so we should permit it.
Signed-off-by: Ulrich Hecht <ulrich.hecht@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Method to disable any core to be used on platforms where CPU0 does not
need special treatment.
Signed-off-by: Ulrich Hecht <ulrich.hecht@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull one s390 fix from Martin Schwidefsky:
"Another transparent huge page fix, we need to define a s390 variant
for pmdp_set_wrprotect to flush the TLB for the huge page correctly."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/thp: implement pmdp_set_wrprotect()
|
|
Add DT entry for pinmux and drive configuration addresses.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Tegra114 has the GPIO controllers with 8 GPIO bank and each bank
supports 32 pins.
Add DT entry for GPIO controller. Tegra114 GPIO controller is
compatible with Tegra30 GPIO controller driver.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Select PINCTRL and PINCTRL_TEGRA114 for enabling Tegra114 pincontrol
driver for Tegra114 SoC.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Adding the generic ARM_CPUIDLE_WFI_STATE support for Tegra114.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Add SMMU entry.
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-rpi into next/dt
From Stephen Warren:
ARM: bcm2835: device tree updates
The SoC's SDHCI and MMC controllers are added to device tree, and enabled
in the Raspberry Pi board device tree. Some fixed clocks are added to the
device tree to support these drivers. These could be replaced by real
clocks in the future.
A hard-coded memreserve is removed from device tree; the bootloader should
specify the correct memory node content instead, since the memory layout
is dynamic.
This branch is based on v3.8-rc3.
* tag 'bcm2835-for-3.9-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-rpi:
ARM: bcm2835: fix clock node aliasing in device tree
ARM: bcm2835: add I2C controllers to DT
ARM: bcm2835: add SDHCI node to DT
ARM: bcm2835 rpi: remove hard-coded memreserve from DT
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-rpi into next/soc
From Stephen Warren:
ARM: bcm2835: SoC driver updates
The bcm2835 clock driver is enhanced to allow fixed clocks to be probed
from device tree.
A system power-off implementation is added.
This branch is based on v3.8-rc3.
* tag 'bcm2835-for-3.9-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-rpi:
ARM: bcm2835: add a pm_power_off implementation
clk: bcm2835: probe for fixed-clock in device tree
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
It looks like the original commit that copied the rom contents from
efi always copied the rom, and the fixup in setup_efi_pci from commit
886d751a2ea99a160 ("x86, efi: correct precedence of operators in
setup_efi_pci") broke that.
This resulted in macbook pro's no longer finding the rom images, and
thus not being able to use the radeon card any more.
The solution is to just remove the check for now, and always copy the
rom if available.
Reported-by: Vitaly Budovski <vbudovski+news@gmail.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Seth Forshee <seth.forshee@canonical.com>
Acked-by: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/dt
From Linus Walleij:
Nomadik Device Tree conversion rebased on ARM SoC cleanup branch
This patch set converts the Nomadik (mach-nomadik) to
Device Tree and delete the old board files, paving the
road for single zImage.
* tag 'nmk-dt-on-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: nomadik: get rid of <mach/hardware.h>
ARM: nomadik: delete old board files
ARM: nomadik: add I2C devices to the device tree
ARM: nomadik: migrate MMC/SD card support to device tree
ARM: nomadik: convert SMSC91x ethernet to device tree
ARM: nomadik: move GPIO and pinctrl to device tree
ARM: nomadik: add FSMC NAND
ARM: nomadik: move remaining PrimeCells to device tree
ARM: nomadik: move pin maps to cpu file
ARM: nomadik: initial devicetree support
ARM: nomadik: move last custom calls to pinctrl
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
|
|
git://gitorious.org/linux-davinci/linux-davinci into next/dt
From Sekhar Nori:
DaVinci DT changes for v3.9
This pull requests adds support for pinctrl, NAND
and RTC support when DA850 is booting using DT.
* tag 'davinci-for-v3.9/dt' of git://gitorious.org/linux-davinci/linux-davinci:
ARM: davinci: da850: add RTC DT entries
ARM: davinci: da850: move interrupt-parent property to soc node
ARM: davinci: da8xx defconfig: enable pinctrl config option
ARM: davinci: da850: add NAND driver DT entries
ARM: davinci: da850: add pinctrl driver DT entries
|
|
git://gitorious.org/linux-davinci/linux-davinci into next/soc
From Sekhar Nori:
DaVinci SoC changes for v3.9
This pull request:
1) Fixes a bug with the way SPI devices were registered on DA850
2) Adds support for DSP clock and resetting the DSP on DA850
3) Fixes checkpatch issue with some existing files.
* tag 'davinci-for-v3.9/soc' of git://gitorious.org/linux-davinci/linux-davinci:
ARM: davinci: da850: add dsp clock definition
ARM: davinci: psc: introduce reset API
ARM: davinci: psc.c: change pr_warning() to pr_warn()
ARM: davinci: devices-da8xx.c: change pr_warning() to pr_warn()
ARM: davinci: da8xx_register_spi() should not register SPI board info
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
From Simon Horman, a series of SoC updates for shmobile.
* 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7779: scif .irqs used SCIx_IRQ_MUXED()
ARM: mach-shmobile: sh73a0: Initialise MMCIF using DT
ARM: mach-shmobile: sh73a0: Minimal setup using DT
ARM: mach-shmobile: sh73a0: Allow initialisation of GIC by DT
ARM: SH-Mobile: sh73a0: Add CPU Hotplug
ARM: SH-Mobile: sh73a0: Secondary CPUs handle own SCU flags
ARM: shmobile: r8a7740: Add CPU sleep suspend
ARM: shmobile: sh73a0: Add CPU sleep suspend
ARM: shmobile: add function declarations for sh7372 DT helper functions
ARM: sh7372: fix cache clean / invalidate order
ARM: sh7372: add clock lookup entries for DT-based devices
ARM: mach-shmobile: sh73a0 external IRQ wake update
ARM: shmobile: sh73a0: fixup div4_clks bitmap
ARM: shmobile: r8a7740: add TMU timer support
ARM: shmobile: Remove duplicate inclusion of dma-mapping.h in setup-r8a7740.c
Signed-off-by: Olof Johansson <olof@lixom.net>
Fix trivial conflict in board_bcm due to Simon resolving the same conflict
with one less line of whitespace. Keeping end result common with what
we already have in arm-soc.
Conflicts:
arch/arm/mach-bcm/board_bcm.c
|
|
Only mx508 based board is mach-mx50_rdp and it has been marked as BROKEN
for several releases.
mx508 currently lacks clock support.
In case someone needs to add mx508 support back, then the recommended approach
is to use device tree.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
