| Age | Commit message (Collapse) | Author |
|---|
|
Remove vendor checks from prefer_mwait_c1_over_halt function. Restore
the decision tree to support MWAIT C1 as the default idle state based on
CPUID checks as done by Thomas Gleixner in
commit 09fd4b4ef5bc ("x86: use cpuid to check MWAIT support for C1")
The decision tree is removed in
commit 69fb3676df33 ("x86 idle: remove mwait_idle() and "idle=mwait" cmdline param")
Prefer MWAIT when the following conditions are satisfied:
1. CPUID_Fn00000001_ECX [Monitor] should be set
2. CPUID_Fn00000005 should be supported
3. If CPUID_Fn00000005_ECX [EMX] is set then there should be
at least one C1 substate available, indicated by
CPUID_Fn00000005_EDX [MWaitC1SubStates] bits.
Otherwise use HLT for default_idle function.
HPC customers who want to optimize for lower latency are known to
disable Global C-States in the BIOS. In fact, some vendors allow
choosing a BIOS 'performance' profile which explicitly disables
C-States. In this scenario, the cpuidle driver will not be loaded and
the kernel will continue with the default idle state chosen at boot
time. On AMD systems currently the default idle state is HLT which has
a higher exit latency compared to MWAIT.
The reason for the choice of HLT over MWAIT on AMD systems is:
1. Families prior to 10h didn't support MWAIT
2. Families 10h-15h supported MWAIT, but not MWAIT C1. Hence it was
preferable to use HLT as the default state on these systems.
However, AMD Family 17h onwards supports MWAIT as well as MWAIT C1. And
it is preferable to use MWAIT as the default idle state on these
systems, as it has lower exit latencies.
The below table represents the exit latency for HLT and MWAIT on AMD
Zen 3 system. Exit latency is measured by issuing a wakeup (IPI) to
other CPU and measuring how many clock cycles it took to wakeup. Each
iteration measures 10K wakeups by pinning source and destination.
HLT:
25.0000th percentile : 1900 ns
50.0000th percentile : 2000 ns
75.0000th percentile : 2300 ns
90.0000th percentile : 2500 ns
95.0000th percentile : 2600 ns
99.0000th percentile : 2800 ns
99.5000th percentile : 3000 ns
99.9000th percentile : 3400 ns
99.9500th percentile : 3600 ns
99.9900th percentile : 5900 ns
Min latency : 1700 ns
Max latency : 5900 ns
Total Samples 9999
MWAIT:
25.0000th percentile : 1400 ns
50.0000th percentile : 1500 ns
75.0000th percentile : 1700 ns
90.0000th percentile : 1800 ns
95.0000th percentile : 1900 ns
99.0000th percentile : 2300 ns
99.5000th percentile : 2500 ns
99.9000th percentile : 3200 ns
99.9500th percentile : 3500 ns
99.9900th percentile : 4600 ns
Min latency : 1200 ns
Max latency : 4600 ns
Total Samples 9997
Improvement (99th percentile): 21.74%
Below is another result for context_switch2 micro-benchmark, which
brings out the impact of improved wakeup latency through increased
context-switches per second.
with HLT:
-------------------------------
50.0000th percentile : 190184
75.0000th percentile : 191032
90.0000th percentile : 192314
95.0000th percentile : 192520
99.0000th percentile : 192844
MIN : 190148
MAX : 192852
with MWAIT:
-------------------------------
50.0000th percentile : 277444
75.0000th percentile : 278268
90.0000th percentile : 278888
95.0000th percentile : 279164
99.0000th percentile : 280504
MIN : 273278
MAX : 281410
Improvement(99th percentile): ~ 45.46%
Signed-off-by: Wyes Karny <wyes.karny@amd.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Zhang Rui <rui.zhang@intel.com>
Link: https://ozlabs.org/~anton/junkcode/context_switch2.c
Link: https://lkml.kernel.org/r/0cc675d8fd1f55e41b510e10abf2e21b6e9803d5.1654538381.git-series.wyes.karny@amd.com
|
|
When kernel is booted with idle=nomwait do not use MWAIT as the
default idle state.
If the user boots the kernel with idle=nomwait, it is a clear
direction to not use mwait as the default idle state.
However, the current code does not take this into consideration
while selecting the default idle state on x86.
Fix it by checking for the idle=nomwait boot option in
prefer_mwait_c1_over_halt().
Also update the documentation around idle=nomwait appropriately.
[ dhansen: tweak commit message ]
Signed-off-by: Wyes Karny <wyes.karny@amd.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Tested-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lkml.kernel.org/r/fdc2dc2d0a1bc21c2f53d989ea2d2ee3ccbc0dbe.1654538381.git-series.wyes.karny@amd.com
|
|
Since
e2a1256b17b1 ("x86/speculation: Restore speculation related MSRs during S3 resume")
kmemleak reports this issue:
unreferenced object 0xffff888009cedc00 (size 256):
comm "swapper/0", pid 1, jiffies 4294693823 (age 73.764s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 48 00 00 00 00 00 00 00 ........H.......
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
msr_build_context (include/linux/slab.h:621)
pm_check_save_msr (arch/x86/power/cpu.c:520)
do_one_initcall (init/main.c:1298)
kernel_init_freeable (init/main.c:1370)
kernel_init (init/main.c:1504)
ret_from_fork (arch/x86/entry/entry_64.S:304)
Reproducer:
- boot the VM with a debug kernel config (see
https://github.com/multipath-tcp/mptcp_net-next/issues/268)
- wait ~1 minute
- start a kmemleak scan
The root cause here is alignment within the packed struct saved_context
(from suspend_64.h). Kmemleak only searches for pointers that are
aligned (see how pointers are scanned in kmemleak.c), but pahole shows
that the saved_msrs struct member and all members after it in the
structure are unaligned:
struct saved_context {
struct pt_regs regs; /* 0 168 */
/* --- cacheline 2 boundary (128 bytes) was 40 bytes ago --- */
u16 ds; /* 168 2 */
...
u64 misc_enable; /* 232 8 */
bool misc_enable_saved; /* 240 1 */
/* Note below odd offset values for the remainder of this struct */
struct saved_msrs saved_msrs; /* 241 16 */
/* --- cacheline 4 boundary (256 bytes) was 1 bytes ago --- */
long unsigned int efer; /* 257 8 */
u16 gdt_pad; /* 265 2 */
struct desc_ptr gdt_desc; /* 267 10 */
u16 idt_pad; /* 277 2 */
struct desc_ptr idt; /* 279 10 */
u16 ldt; /* 289 2 */
u16 tss; /* 291 2 */
long unsigned int tr; /* 293 8 */
long unsigned int safety; /* 301 8 */
long unsigned int return_address; /* 309 8 */
/* size: 317, cachelines: 5, members: 25 */
/* last cacheline: 61 bytes */
} __attribute__((__packed__));
Move misc_enable_saved to the end of the struct declaration so that
saved_msrs fits in before the cacheline 4 boundary.
The comment above the saved_context declaration says to fix wakeup_64.S
file and __save/__restore_processor_state() if the struct is modified:
it looks like all the accesses in wakeup_64.S are done through offsets
which are computed at build-time. Update that comment accordingly.
At the end, the false positive kmemleak report is due to a limitation
from kmemleak but it is always good to avoid unaligned members for
optimisation purposes.
Please note that it looks like this issue is not new, e.g.
https://lore.kernel.org/all/9f1bb619-c4ee-21c4-a251-870bd4db04fa@lwfinger.net/
https://lore.kernel.org/all/94e48fcd-1dbd-ebd2-4c91-f39941735909@molgen.mpg.de/
[ bp: Massage + cleanup commit message. ]
Fixes: 7a9c2dd08ead ("x86/pm: Introduce quirk framework to save/restore extra MSR registers around suspend/resume")
Suggested-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/20220426202138.498310-1-matthieu.baerts@tessares.net
|
|
When SRBDS is mitigated by TSX OFF, update_srbds_msr() will still read
and write to MSR_IA32_MCU_OPT_CTRL even when that MSR is not supported
due to not having loaded the appropriate microcode.
Check for X86_FEATURE_SRBDS_CTRL which is set only when the respective
microcode which adds MSR_IA32_MCU_OPT_CTRL is loaded.
Based on a patch by Thadeu Lima de Souza Cascardo <cascardo@canonical.com>.
[ bp: Massage commit message. ]
Suggested-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20220401074517.1848264-1-ricardo.canuelo@collabora.com
|
|
Not really needed anymore and there's clearcpuid=.
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20220127115626.14179-7-bp@alien8.de
|
|
It doesn't make any sense to disable non-executable mappings -
security-wise or else.
So rip out that switch and move the remaining code into setup.c and
delete setup_nx.c
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Lai Jiangshan <jiangshanlai@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20220127115626.14179-6-bp@alien8.de
|
|
There should be no need to disable SMEP anymore.
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Lai Jiangshan <jiangshanlai@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20220127115626.14179-5-bp@alien8.de
|
|
Those were added as part of the SMAP enablement but SMAP is currently
an integral part of kernel proper and there's no need to disable it
anymore.
Rip out that functionality. Leave --uaccess default on for objtool as
this is what objtool should do by default anyway.
If still needed - clearcpuid=smap.
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Lai Jiangshan <jiangshanlai@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20220127115626.14179-4-bp@alien8.de
|
|
That chicken bit was added by
4f88651125e2 ("[PATCH] i386: allow disabling X86_FEATURE_SEP at boot")
but measuring int80 vsyscall performance on 32-bit doesn't matter
anymore.
If still needed, one can boot with
clearcpuid=sep
to disable that feature for testing.
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20220127115626.14179-3-bp@alien8.de
|
|
Having to give the X86_FEATURE array indices in order to disable a
feature bit for testing is not really user-friendly. So accept the
feature bit names too.
Some feature bits don't have names so there the array indices are still
accepted, of course.
Clearing CPUID flags is not something which should be done in production
so taint the kernel too.
An exemplary cmdline would then be something like:
clearcpuid=de,440,smca,succory,bmi1,3dnow
("succory" is wrong on purpose). And it says:
[ ... ] Clearing CPUID bits: de 13:24 smca (unknown: succory) bmi1 3dnow
[ Fix CONFIG_X86_FEATURE_NAMES=n build error as reported by the 0day
robot: https://lore.kernel.org/r/202203292206.ICsY2RKX-lkp@intel.com ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20220127115626.14179-2-bp@alien8.de
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A set of x86 fixes and updates:
- Make the prctl() for enabling dynamic XSTATE components correct so
it adds the newly requested feature to the permission bitmap
instead of overwriting it. Add a selftest which validates that.
- Unroll string MMIO for encrypted SEV guests as the hypervisor
cannot emulate it.
- Handle supervisor states correctly in the FPU/XSTATE code so it
takes the feature set of the fpstate buffer into account. The
feature sets can differ between host and guest buffers. Guest
buffers do not contain supervisor states. So far this was not an
issue, but with enabling PASID it needs to be handled in the buffer
offset calculation and in the permission bitmaps.
- Avoid a gazillion of repeated CPUID invocations in by caching the
values early in the FPU/XSTATE code.
- Enable CONFIG_WERROR in x86 defconfig.
- Make the X86 defconfigs more useful by adapting them to Y2022
reality"
* tag 'x86-urgent-2022-04-03' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/fpu/xstate: Consolidate size calculations
x86/fpu/xstate: Handle supervisor states in XSTATE permissions
x86/fpu/xsave: Handle compacted offsets correctly with supervisor states
x86/fpu: Cache xfeature flags from CPUID
x86/fpu/xsave: Initialize offset/size cache early
x86/fpu: Remove unused supervisor only offsets
x86/fpu: Remove redundant XCOMP_BV initialization
x86/sev: Unroll string mmio with CC_ATTR_GUEST_UNROLL_STRING_IO
x86/config: Make the x86 defconfigs a bit more usable
x86/defconfig: Enable WERROR
selftests/x86/amx: Update the ARCH_REQ_XCOMP_PERM test
x86/fpu/xstate: Fix the ARCH_REQ_XCOMP_PERM implementation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull RT signal fix from Thomas Gleixner:
"Revert the RT related signal changes. They need to be reworked and
generalized"
* tag 'core-urgent-2022-04-03' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "signal, x86: Delay calling signals in atomic on RT enabled kernels"
|
|
Pull ARM fixes from Russell King:
- avoid unnecessary rebuilds for library objects
- fix return value of __setup handlers
- fix invalid input check for "crashkernel=" kernel option
- silence KASAN warnings in unwind_frame
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 9191/1: arm/stacktrace, kasan: Silence KASAN warnings in unwind_frame()
ARM: 9190/1: kdump: add invalid input check for 'crashkernel=0'
ARM: 9187/1: JIVE: fix return value of __setup handler
ARM: 9189/1: decompressor: fix unneeded rebuilds of library objects
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- Fix empty $(PYTHON) expansion.
- Fix UML, which got broken by the attempt to suppress Clang warnings.
- Fix warning message in modpost.
* tag 'kbuild-fixes-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
modpost: restore the warning message for missing symbol versions
Revert "um: clang: Strip out -mno-global-merge from USER_CFLAGS"
kbuild: Remove '-mno-global-merge'
kbuild: fix empty ${PYTHON} in scripts/link-vmlinux.sh
kconfig: remove stale comment about removed kconfig_print_symbol()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Thomas Bogendoerfer:
- build fix for gpio
- fix crc32 build problems
- check for failed memory allocations
* tag 'mips_5.18_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: crypto: Fix CRC32 code
MIPS: rb532: move GPIOD definition into C-files
MIPS: lantiq: check the return value of kzalloc()
mips: sgi-ip22: add a check for the return of kzalloc()
|
|
Pull kvm fixes from Paolo Bonzini:
- Only do MSR filtering for MSRs accessed by rdmsr/wrmsr
- Documentation improvements
- Prevent module exit until all VMs are freed
- PMU Virtualization fixes
- Fix for kvm_irq_delivery_to_apic_fast() NULL-pointer dereferences
- Other miscellaneous bugfixes
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (42 commits)
KVM: x86: fix sending PV IPI
KVM: x86/mmu: do compare-and-exchange of gPTE via the user address
KVM: x86: Remove redundant vm_entry_controls_clearbit() call
KVM: x86: cleanup enter_rmode()
KVM: x86: SVM: fix tsc scaling when the host doesn't support it
kvm: x86: SVM: remove unused defines
KVM: x86: SVM: move tsc ratio definitions to svm.h
KVM: x86: SVM: fix avic spec based definitions again
KVM: MIPS: remove reference to trap&emulate virtualization
KVM: x86: document limitations of MSR filtering
KVM: x86: Only do MSR filtering when access MSR by rdmsr/wrmsr
KVM: x86/emulator: Emulate RDPID only if it is enabled in guest
KVM: x86/pmu: Fix and isolate TSX-specific performance event logic
KVM: x86: mmu: trace kvm_mmu_set_spte after the new SPTE was set
KVM: x86/svm: Clear reserved bits written to PerfEvtSeln MSRs
KVM: x86: Trace all APICv inhibit changes and capture overall status
KVM: x86: Add wrappers for setting/clearing APICv inhibits
KVM: x86: Make APICv inhibit reasons an enum and cleanup naming
KVM: X86: Handle implicit supervisor access with SMAP
KVM: X86: Rename variable smap to not_smap in permission_fault()
...
|
|
If apic_id is less than min, and (max - apic_id) is greater than
KVM_IPI_CLUSTER_SIZE, then the third check condition is satisfied but
the new apic_id does not fit the bitmask. In this case __send_ipi_mask
should send the IPI.
This is mostly theoretical, but it can happen if the apic_ids on three
iterations of the loop are for example 1, KVM_IPI_CLUSTER_SIZE, 0.
Fixes: aaffcfd1e82 ("KVM: X86: Implement PV IPIs in linux guest")
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Message-Id: <1646814944-51801-1-git-send-email-lirongqing@baidu.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
FNAME(cmpxchg_gpte) is an inefficient mess. It is at least decent if it
can go through get_user_pages_fast(), but if it cannot then it tries to
use memremap(); that is not just terribly slow, it is also wrong because
it assumes that the VM_PFNMAP VMA is contiguous.
The right way to do it would be to do the same thing as
hva_to_pfn_remapped() does since commit add6a0cd1c5b ("KVM: MMU: try to
fix up page faults before giving up", 2016-07-05), using follow_pte()
and fixup_user_fault() to determine the correct address to use for
memremap(). To do this, one could for example extract hva_to_pfn()
for use outside virt/kvm/kvm_main.c. But really there is no reason to
do that either, because there is already a perfectly valid address to
do the cmpxchg() on, only it is a userspace address. That means doing
user_access_begin()/user_access_end() and writing the code in assembly
to handle exceptions correctly. Worse, the guest PTE can be 8-byte
even on i686 so there is the extra complication of using cmpxchg8b to
account for. But at least it is an efficient mess.
(Thanks to Linus for suggesting improvement on the inline assembly).
Reported-by: Qiuhao Li <qiuhao@sysec.org>
Reported-by: Gaoning Pan <pgn@zju.edu.cn>
Reported-by: Yongkang Jia <kangel@zju.edu.cn>
Reported-by: syzbot+6cde2282daa792c49ab8@syzkaller.appspotmail.com
Debugged-by: Tadeusz Struk <tadeusz.struk@linaro.org>
Tested-by: Maxim Levitsky <mlevitsk@redhat.com>
Cc: stable@vger.kernel.org
Fixes: bd53cb35a3e9 ("X86/KVM: Handle PFNs outside of kernel reach when touching GPTEs")
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
When emulating exit from long mode, EFER_LMA is cleared with
vmx_set_efer(). This will already unset the VM_ENTRY_IA32E_MODE control
bit as requested by SDM, so there is no need to unset VM_ENTRY_IA32E_MODE
again in exit_lmode() explicitly. In case EFER isn't supported by
hardware, long mode isn't supported, so exit_lmode() cannot be reached.
Note that, thanks to the shadow controls mechanism, this change doesn't
eliminate vmread or vmwrite.
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Message-Id: <20220311102643.807507-3-zhenzhong.duan@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
vmx_set_efer() sets uret->data but, in fact if the value of uret->data
will be used vmx_setup_uret_msrs() will have rewritten it with the value
returned by update_transition_efer(). uret->data is consumed if and only
if uret->load_into_hardware is true, and vmx_setup_uret_msrs() takes care
of (a) updating uret->data before setting uret->load_into_hardware to true
(b) setting uret->load_into_hardware to false if uret->data isn't updated.
Opportunistically use "vmx" directly instead of redoing to_vmx().
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Message-Id: <20220311102643.807507-2-zhenzhong.duan@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
It was decided that when TSC scaling is not supported,
the virtual MSR_AMD64_TSC_RATIO should still have the default '1.0'
value.
However in this case kvm_max_tsc_scaling_ratio is not set,
which breaks various assumptions.
Fix this by always calculating kvm_max_tsc_scaling_ratio regardless of
host support. For consistency, do the same for VMX.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20220322172449.235575-8-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Remove some unused #defines from svm.c
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20220322172449.235575-7-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Another piece of SVM spec which should be in the header file
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20220322172449.235575-6-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Due to wrong rebase, commit
4a204f7895878 ("KVM: SVM: Allow AVIC support on system w/ physical APIC ID > 255")
moved avic spec #defines back to avic.c.
Move them back, and while at it extend AVIC_DOORBELL_PHYSICAL_ID_MASK to 12
bits as well (it will be used in nested avic)
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20220322172449.235575-5-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
If MSR access is rejected by MSR filtering,
kvm_set_msr()/kvm_get_msr() would return KVM_MSR_RET_FILTERED,
and the return value is only handled well for rdmsr/wrmsr.
However, some instruction emulation and state transition also
use kvm_set_msr()/kvm_get_msr() to do msr access but may trigger
some unexpected results if MSR access is rejected, E.g. RDPID
emulation would inject a #UD but RDPID wouldn't cause a exit
when RDPID is supported in hardware and ENABLE_RDTSCP is set.
And it would also cause failure when load MSR at nested entry/exit.
Since msr filtering is based on MSR bitmap, it is better to only
do MSR filtering for rdmsr/wrmsr.
Signed-off-by: Hou Wenlong <houwenlong.hwl@antgroup.com>
Message-Id: <2b2774154f7532c96a6f04d71c82a8bec7d9e80b.1646655860.git.houwenlong.hwl@antgroup.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
When RDTSCP is supported but RDPID is not supported in host,
RDPID emulation is available. However, __kvm_get_msr() would
only fail when RDTSCP/RDPID both are disabled in guest, so
the emulator wouldn't inject a #UD when RDPID is disabled but
RDTSCP is enabled in guest.
Fixes: fb6d4d340e05 ("KVM: x86: emulate RDPID")
Signed-off-by: Hou Wenlong <houwenlong.hwl@antgroup.com>
Message-Id: <1dfd46ae5b76d3ed87bde3154d51c64ea64c99c1.1646226788.git.houwenlong.hwl@antgroup.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
HSW_IN_TX* bits are used in generic code which are not supported on
AMD. Worse, these bits overlap with AMD EventSelect[11:8] and hence
using HSW_IN_TX* bits unconditionally in generic code is resulting in
unintentional pmu behavior on AMD. For example, if EventSelect[11:8]
is 0x2, pmc_reprogram_counter() wrongly assumes that
HSW_IN_TX_CHECKPOINTED is set and thus forces sampling period to be 0.
Also per the SDM, both bits 32 and 33 "may only be set if the processor
supports HLE or RTM" and for "IN_TXCP (bit 33): this bit may only be set
for IA32_PERFEVTSEL2."
Opportunistically eliminate code redundancy, because if the HSW_IN_TX*
bit is set in pmc->eventsel, it is already set in attr.config.
Reported-by: Ravi Bangoria <ravi.bangoria@amd.com>
Reported-by: Jim Mattson <jmattson@google.com>
Fixes: 103af0a98788 ("perf, kvm: Support the in_tx/in_tx_cp modifiers in KVM arch perfmon emulation v5")
Co-developed-by: Ravi Bangoria <ravi.bangoria@amd.com>
Signed-off-by: Ravi Bangoria <ravi.bangoria@amd.com>
Signed-off-by: Like Xu <likexu@tencent.com>
Message-Id: <20220309084257.88931-1-likexu@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
It makes more sense to print new SPTE value than the
old value.
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220302102457.588450-1-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
AMD EPYC CPUs never raise a #GP for a WRMSR to a PerfEvtSeln MSR. Some
reserved bits are cleared, and some are not. Specifically, on
Zen3/Milan, bits 19 and 42 are not cleared.
When emulating such a WRMSR, KVM should not synthesize a #GP,
regardless of which bits are set. However, undocumented bits should
not be passed through to the hardware MSR. So, rather than checking
for reserved bits and synthesizing a #GP, just clear the reserved
bits.
This may seem pedantic, but since KVM currently does not support the
"Host/Guest Only" bits (41:40), it is necessary to clear these bits
rather than synthesizing #GP, because some popular guests (e.g Linux)
will set the "Host Only" bit even on CPUs that don't support
EFER.SVME, and they don't expect a #GP.
For example,
root@Ubuntu1804:~# perf stat -e r26 -a sleep 1
Performance counter stats for 'system wide':
0 r26
1.001070977 seconds time elapsed
Feb 23 03:59:58 Ubuntu1804 kernel: [ 405.379957] unchecked MSR access error: WRMSR to 0xc0010200 (tried to write 0x0000020000130026) at rIP: 0xffffffff9b276a28 (native_write_msr+0x8/0x30)
Feb 23 03:59:58 Ubuntu1804 kernel: [ 405.379958] Call Trace:
Feb 23 03:59:58 Ubuntu1804 kernel: [ 405.379963] amd_pmu_disable_event+0x27/0x90
Fixes: ca724305a2b0 ("KVM: x86/vPMU: Implement AMD vPMU code for KVM")
Reported-by: Lotus Fenn <lotusf@google.com>
Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Like Xu <likexu@tencent.com>
Reviewed-by: David Dunn <daviddunn@google.com>
Message-Id: <20220226234131.2167175-1-jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Trace all APICv inhibit changes instead of just those that result in
APICv being (un)inhibited, and log the current state. Debugging why
APICv isn't working is frustrating as it's hard to see why APICv is still
inhibited, and logging only the first inhibition means unnecessary onion
peeling.
Opportunistically drop the export of the tracepoint, it is not and should
not be used by vendor code due to the need to serialize toggling via
apicv_update_lock.
Note, using the common flow means kvm_apicv_init() switched from atomic
to non-atomic bitwise operations. The VM is unreachable at init, so
non-atomic is perfectly ok.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220311043517.17027-4-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Add set/clear wrappers for toggling APICv inhibits to make the call sites
more readable, and opportunistically rename the inner helpers to align
with the new wrappers and to make them more readable as well. Invert the
flag from "activate" to "set"; activate is painfully ambiguous as it's
not obvious if the inhibit is being activated, or if APICv is being
activated, in which case the inhibit is being deactivated.
For the functions that take @set, swap the order of the inhibit reason
and @set so that the call sites are visually similar to those that bounce
through the wrapper.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220311043517.17027-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Use an enum for the APICv inhibit reasons, there is no meaning behind
their values and they most definitely are not "unsigned longs". Rename
the various params to "reason" for consistency and clarity (inhibit may
be confused as a command, i.e. inhibit APICv, instead of the reason that
is getting toggled/checked).
No functional change intended.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220311043517.17027-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
There are two kinds of implicit supervisor access
implicit supervisor access when CPL = 3
implicit supervisor access when CPL < 3
Current permission_fault() handles only the first kind for SMAP.
But if the access is implicit when SMAP is on, data may not be read
nor write from any user-mode address regardless the current CPL.
So the second kind should be also supported.
The first kind can be detect via CPL and access mode: if it is
supervisor access and CPL = 3, it must be implicit supervisor access.
But it is not possible to detect the second kind without extra
information, so this patch adds an artificial PFERR_EXPLICIT_ACCESS
into @access. This extra information also works for the first kind, so
the logic is changed to use this information for both cases.
The value of PFERR_EXPLICIT_ACCESS is deliberately chosen to be bit 48
which is in the most significant 16 bits of u64 and less likely to be
forced to change due to future hardware uses it.
This patch removes the call to ->get_cpl() for access mode is determined
by @access. Not only does it reduce a function call, but also remove
confusions when the permission is checked for nested TDP. The nested
TDP shouldn't have SMAP checking nor even the L2's CPL have any bearing
on it. The original code works just because it is always user walk for
NPT and SMAP fault is not set for EPT in update_permission_bitmask.
Signed-off-by: Lai Jiangshan <jiangshan.ljs@antgroup.com>
Message-Id: <20220311070346.45023-5-jiangshanlai@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Comments above the variable says the bit is set when SMAP is overridden
or the same meaning in update_permission_bitmask(): it is not subjected
to SMAP restriction.
Renaming it to reflect the negative implication and make the code better
readability.
Signed-off-by: Lai Jiangshan <jiangshan.ljs@antgroup.com>
Message-Id: <20220311070346.45023-4-jiangshanlai@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The commit 09f037aa48f3 ("KVM: MMU: speedup update_permission_bitmask")
refactored the code of update_permission_bitmask() and change the
comments. It added a condition into a list to match the new code,
so the number/order for conditions in the comments should be updated
too.
Signed-off-by: Lai Jiangshan <jiangshan.ljs@antgroup.com>
Message-Id: <20220311070346.45023-3-jiangshanlai@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Change the type of access u32 to u64 for FNAME(walk_addr) and
->gva_to_gpa().
The kinds of accesses are usually combinations of UWX, and VMX/SVM's
nested paging adds a new factor of access: is it an access for a guest
page table or for a final guest physical address.
And SMAP relies a factor for supervisor access: explicit or implicit.
So @access in FNAME(walk_addr) and ->gva_to_gpa() is better to include
all these information to do the walk.
Although @access(u32) has enough bits to encode all the kinds, this
patch extends it to u64:
o Extra bits will be in the higher 32 bits, so that we can
easily obtain the traditional access mode (UWX) by converting
it to u32.
o Reuse the value for the access kind defined by SVM's nested
paging (PFERR_GUEST_FINAL_MASK and PFERR_GUEST_PAGE_MASK) as
@error_code in kvm_handle_page_fault().
Signed-off-by: Lai Jiangshan <jiangshan.ljs@antgroup.com>
Message-Id: <20220311070346.45023-2-jiangshanlai@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
It isn't OK to cache the dirty status of a page in internal structures
for an indefinite period of time.
Any time a vCPU exits the run loop to userspace might be its last; the
VMM might do its final check of the dirty log, flush the last remaining
dirty pages to the destination and complete a live migration. If we
have internal 'dirty' state which doesn't get flushed until the vCPU
is finally destroyed on the source after migration is complete, then
we have lost data because that will escape the final copy.
This problem already exists with the use of kvm_vcpu_unmap() to mark
pages dirty in e.g. VMX nesting.
Note that the actual Linux MM already considers the page to be dirty
since we have a writeable mapping of it. This is just about the KVM
dirty logging.
For the nesting-style use cases (KVM_GUEST_USES_PFN) we will need to
track which gfn_to_pfn_caches have been used and explicitly mark the
corresponding pages dirty before returning to userspace. But we would
have needed external tracking of that anyway, rather than walking the
full list of GPCs to find those belonging to this vCPU which are dirty.
So let's rely *solely* on that external tracking, and keep it simple
rather than laying a tempting trap for callers to fall into.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20220303154127.202856-3-dwmw2@infradead.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Replace the guest_uses_pa and kernel_map booleans in the PFN cache code
with a unified enum/bitmask. Using explicit names makes it easier to
review and audit call sites.
Opportunistically add a WARN to prevent passing garbage; instantating a
cache without declaring its usage is either buggy or pointless.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20220303154127.202856-2-dwmw2@infradead.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Include kvm_cache_regs.h to pick up the definition of is_guest_mode(),
which is referenced by nested_svm_virtualize_tpr() in svm.h. Remove
include from svm_onhpyerv.c which was done only because of lack of
include in svm.h.
Fixes: 883b0a91f41ab ("KVM: SVM: Move Nested SVM Implementation to nested.c")
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Sean Christopherson <seanjc@google.com>
Cc: kvm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Peter Gonda <pgonda@google.com>
Message-Id: <20220304161032.2270688-1-pgonda@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The third nybble of AMD's event select overlaps with Intel's IN_TX and
IN_TXCP bits. Therefore, we can't use AMD64_RAW_EVENT_MASK on Intel
platforms that support TSX.
Declare a raw_event_mask in the kvm_pmu structure, initialize it in
the vendor-specific pmu_refresh() functions, and use that mask for
PERF_TYPE_RAW configurations in reprogram_gp_counter().
Fixes: 710c47651431 ("KVM: x86/pmu: Use AMD64_RAW_EVENT_MASK for PERF_TYPE_RAW")
Signed-off-by: Jim Mattson <jmattson@google.com>
Message-Id: <20220308012452.3468611-1-jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Don't actually set a request bit in vcpu->requests when making a request
purely to force a vCPU to exit the guest. Logging a request but not
actually consuming it would cause the vCPU to get stuck in an infinite
loop during KVM_RUN because KVM would see the pending request and bail
from VM-Enter to service the request.
Note, it's currently impossible for KVM to set KVM_REQ_GPC_INVALIDATE as
nothing in KVM is wired up to set guest_uses_pa=true. But, it'd be all
too easy for arch code to introduce use of kvm_gfn_to_pfn_cache_init()
without implementing handling of the request, especially since getting
test coverage of MMU notifier interaction with specific KVM features
usually requires a directed test.
Opportunistically rename gfn_to_pfn_cache_invalidate_start()'s wake_vcpus
to evict_vcpus. The purpose of the request is to get vCPUs out of guest
mode, it's supposed to _avoid_ waking vCPUs that are blocking.
Opportunistically rename KVM_REQ_GPC_INVALIDATE to be more specific as to
what it wants to accomplish, and to genericize the name so that it can
used for similar but unrelated scenarios, should they arise in the future.
Add a comment and documentation to explain why the "no action" request
exists.
Add compile-time assertions to help detect improper usage. Use the inner
assertless helper in the one s390 path that makes requests without a
hardcoded request.
Cc: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220223165302.3205276-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Re-introduce zapping only leaf SPTEs in kvm_zap_gfn_range() and
kvm_tdp_mmu_unmap_gfn_range(), this time without losing a pending TLB
flush when processing multiple roots (including nested TDP shadow roots).
Dropping the TLB flush resulted in random crashes when running Hyper-V
Server 2019 in a guest with KSM enabled in the host (or any source of
mmu_notifier invalidations, KSM is just the easiest to force).
This effectively revert commits 873dd122172f8cce329113cfb0dfe3d2344d80c0
and fcb93eb6d09dd302cbef22bd95a5858af75e4156, and thus restores commit
cf3e26427c08ad9015956293ab389004ac6a338e, plus this delta on top:
bool kvm_tdp_mmu_zap_leafs(struct kvm *kvm, int as_id, gfn_t start, gfn_t end,
struct kvm_mmu_page *root;
for_each_tdp_mmu_root_yield_safe(kvm, root, as_id)
- flush = tdp_mmu_zap_leafs(kvm, root, start, end, can_yield, false);
+ flush = tdp_mmu_zap_leafs(kvm, root, start, end, can_yield, flush);
return flush;
}
Cc: Ben Gardon <bgardon@google.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Tested-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20220325230348.2587437-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
As guest_irq is coming from KVM_IRQFD API call, it may trigger
crash in svm_update_pi_irte() due to out-of-bounds:
crash> bt
PID: 22218 TASK: ffff951a6ad74980 CPU: 73 COMMAND: "vcpu8"
#0 [ffffb1ba6707fa40] machine_kexec at ffffffff8565b397
#1 [ffffb1ba6707fa90] __crash_kexec at ffffffff85788a6d
#2 [ffffb1ba6707fb58] crash_kexec at ffffffff8578995d
#3 [ffffb1ba6707fb70] oops_end at ffffffff85623c0d
#4 [ffffb1ba6707fb90] no_context at ffffffff856692c9
#5 [ffffb1ba6707fbf8] exc_page_fault at ffffffff85f95b51
#6 [ffffb1ba6707fc50] asm_exc_page_fault at ffffffff86000ace
[exception RIP: svm_update_pi_irte+227]
RIP: ffffffffc0761b53 RSP: ffffb1ba6707fd08 RFLAGS: 00010086
RAX: ffffb1ba6707fd78 RBX: ffffb1ba66d91000 RCX: 0000000000000001
RDX: 00003c803f63f1c0 RSI: 000000000000019a RDI: ffffb1ba66db2ab8
RBP: 000000000000019a R8: 0000000000000040 R9: ffff94ca41b82200
R10: ffffffffffffffcf R11: 0000000000000001 R12: 0000000000000001
R13: 0000000000000001 R14: ffffffffffffffcf R15: 000000000000005f
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#7 [ffffb1ba6707fdb8] kvm_irq_routing_update at ffffffffc09f19a1 [kvm]
#8 [ffffb1ba6707fde0] kvm_set_irq_routing at ffffffffc09f2133 [kvm]
#9 [ffffb1ba6707fe18] kvm_vm_ioctl at ffffffffc09ef544 [kvm]
RIP: 00007f143c36488b RSP: 00007f143a4e04b8 RFLAGS: 00000246
RAX: ffffffffffffffda RBX: 00007f05780041d0 RCX: 00007f143c36488b
RDX: 00007f05780041d0 RSI: 000000004008ae6a RDI: 0000000000000020
RBP: 00000000000004e8 R8: 0000000000000008 R9: 00007f05780041e0
R10: 00007f0578004560 R11: 0000000000000246 R12: 00000000000004e0
R13: 000000000000001a R14: 00007f1424001c60 R15: 00007f0578003bc0
ORIG_RAX: 0000000000000010 CS: 0033 SS: 002b
Vmx have been fix this in commit 3a8b0677fc61 (KVM: VMX: Do not BUG() on
out-of-bounds guest IRQ), so we can just copy source from that to fix
this.
Co-developed-by: Yi Liu <liu.yi24@zte.com.cn>
Signed-off-by: Yi Liu <liu.yi24@zte.com.cn>
Signed-off-by: Yi Wang <wang.yi59@zte.com.cn>
Message-Id: <20220309113025.44469-1-wang.yi59@zte.com.cn>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
If kvm->arch.tdp_mmu_zap_wq cannot be created, the failure has
to be propagated up to kvm_mmu_init_vm and kvm_arch_init_vm.
kvm_arch_init_vm also has to undo all the initialization, so
group all the MMU initialization code at the beginning and
handle cleaning up of kvm_page_track_init.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs updates from Al Viro:
"Assorted bits and pieces"
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
aio: drop needless assignment in aio_read()
clean overflow checks in count_mounts() a bit
seq_file: fix NULL pointer arithmetic warning
uml/x86: use x86 load_unaligned_zeropad()
asm/user.h: killed unused macros
constify struct path argument of finish_automount()/do_add_mount()
fs: Remove FIXME comment in generic_write_checks()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull more RISC-V updates from Palmer Dabbelt:
"This has a handful of new features:
- Support for CURRENT_STACK_POINTER, which enables some extra stack
debugging for HARDENED_USERCOPY.
- Support for the new SBI CPU idle extension, via cpuidle and suspend
drivers.
- Profiling has been enabled in the defconfigs.
but is mostly fixes and cleanups"
* tag 'riscv-for-linus-5.18-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (21 commits)
RISC-V: K210 defconfigs: Drop redundant MEMBARRIER=n
RISC-V: defconfig: Drop redundant SBI HVC and earlycon
Documentation: riscv: remove non-existent directory from table of contents
riscv: cpu.c: don't use kernel-doc markers for comments
RISC-V: Enable profiling by default
RISC-V: module: fix apply_r_riscv_rcv_branch_rela typo
RISC-V: Declare per cpu boot data as static
RISC-V: Fix a comment typo in riscv_of_parent_hartid()
riscv: Increase stack size under KASAN
riscv: Fix fill_callchain return value
riscv: dts: canaan: Fix SPI3 bus width
riscv: Rename "sp_in_global" to "current_stack_pointer"
riscv module: remove (NOLOAD)
RISC-V: Enable RISC-V SBI CPU Idle driver for QEMU virt machine
dt-bindings: Add common bindings for ARM and RISC-V idle states
cpuidle: Add RISC-V SBI CPU idle driver
cpuidle: Factor-out power domain related code from PSCI domain driver
RISC-V: Add SBI HSM suspend related defines
RISC-V: Add arch functions for non-retentive suspend entry/exit
RISC-V: Rename relocate() and make it global
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull more s390 updates from Vasily Gorbik:
- Add kretprobes framepointer verification and return address recovery
in stacktrace.
- Support control domain masks on custom zcrypt devices and filter
admin requests.
- Cleanup timer API usage.
- Rework absolute lowcore access helpers.
- Other various small improvements and fixes.
* tag 's390-5.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (26 commits)
s390/alternatives: avoid using jgnop mnemonic
s390/pci: rename get_zdev_by_bus() to zdev_from_bus()
s390/pci: improve zpci_dev reference counting
s390/smp: use physical address for SIGP_SET_PREFIX command
s390: cleanup timer API use
s390/zcrypt: fix using the correct variable for sizeof()
s390/vfio-ap: fix kernel doc and signature of group notifier functions
s390/maccess: rework absolute lowcore accessors
s390/smp: cleanup control register update routines
s390/smp: cleanup target CPU callback starting
s390/test_unwind: verify __kretprobe_trampoline is replaced
s390/unwind: avoid duplicated unwinding entries for kretprobes
s390/unwind: recover kretprobe modified return address in stacktrace
s390/kprobes: enable kretprobes framepointer verification
s390/test_unwind: extend kretprobe test
s390/ap: adjust whitespace
s390/ap: use insn format for new instructions
s390/alternatives: use insn format for new instructions
s390/alternatives: use instructions instead of byte patterns
s390/traps: improve panic message for translation-specification exception
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd BergmannL
"The introduction of vmap-stack on 32-bit arm caused a regression on a
few omap3/omap4 machines that pass a stack variable into a firmware
interface.
The early pre-ACPI AMD Seattle machines have been broken for a while,
Ard Biesheuvel has a series to bring them back for now.
A few machines with multiple DMA channels used on a device have the
channels in the wrong order according to the binding, which causes a
harmless warning. Reversing the order is easier than fixing the tools
to suppress the warning"
* tag 'soc-fixes-5.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
arm64: dts: ls1046a: Update i2c node dma properties
arm64: dts: ls1043a: Update i2c dma properties
ARM: dts: spear1340: Update serial node properties
ARM: dts: spear13xx: Update SPI dma properties
ARM: OMAP2+: Fix regression for smc calls for vmap stack
dt: amd-seattle: add a description of the CPUs and caches
dt: amd-seattle: disable IPMI controller and some GPIO blocks on B0
dt: amd-seattle: add description of the SATA/CCP SMMUs
dt: amd-seattle: add a description of the PCIe SMMU
dt: amd-seattle: fix PCIe legacy interrupt routing
dt: amd-seattle: upgrade AMD Seattle XGBE to new SMMU binding
dt: amd-seattle: remove Overdrive revision A0 support
dt: amd-seattle: remove Husky platform
|
|
|
|
This reverts commit 6580c5c18fb3df2b11c5e0452372f815deeff895.
This patch is buggy, as noted in the patch linked below. The root cause
has been solved by removing '-mno-global-merge' for the entire kernel.
Link: https://lore.kernel.org/r/20220322173547.677760-1-nathan@kernel.org/
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: David Gow <davidgow@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
