summaryrefslogtreecommitdiff
path: root/block/blk-cgroup.c
AgeCommit message (Collapse)Author
2016-06-14block/blk-cgroup.c: Declare local symbols staticBart Van Assche
Detected by sparse. Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-02-09block: fix module reference leak on put_disk() call for cgroups throttleRoman Pen
get_disk(),get_gendisk() calls have non explicit side effect: they increase the reference on the disk owner module. The following is the correct sequence how to get a disk reference and to put it: disk = get_gendisk(...); /* use disk */ owner = disk->fops->owner; put_disk(disk); module_put(owner); fs/block_dev.c is aware of this required module_put() call, but f.e. blkg_conf_finish(), which is located in block/blk-cgroup.c, does not put a module reference. To see a leakage in action cgroups throttle config can be used. In the following script I'm removing throttle for /dev/ram0 (actually this is NOP, because throttle was never set for this device): # lsmod | grep brd brd 5175 0 # i=100; while [ $i -gt 0 ]; do echo "1:0 0" > \ /sys/fs/cgroup/blkio/blkio.throttle.read_bps_device; i=$(($i - 1)); \ done # lsmod | grep brd brd 5175 100 Now brd module has 100 references. The issue is fixed by calling module_put() just right away put_disk(). Signed-off-by: Roman Pen <roman.penyaev@profitbricks.com> Cc: Gi-Oh Kim <gi-oh.kim@profitbricks.com> Cc: Tejun Heo <tj@kernel.org> Cc: Jens Axboe <axboe@kernel.dk> Cc: linux-block@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Jens Axboe <axboe@fb.com>
2015-12-03cgroup: fix handling of multi-destination migration from subtree_control ↵Tejun Heo
enabling Consider the following v2 hierarchy. P0 (+memory) --- P1 (-memory) --- A \- B P0 has memory enabled in its subtree_control while P1 doesn't. If both A and B contain processes, they would belong to the memory css of P1. Now if memory is enabled on P1's subtree_control, memory csses should be created on both A and B and A's processes should be moved to the former and B's processes the latter. IOW, enabling controllers can cause atomic migrations into different csses. The core cgroup migration logic has been updated accordingly but the controller migration methods haven't and still assume that all tasks migrate to a single target css; furthermore, the methods were fed the css in which subtree_control was updated which is the parent of the target csses. pids controller depends on the migration methods to move charges and this made the controller attribute charges to the wrong csses often triggering the following warning by driving a counter negative. WARNING: CPU: 1 PID: 1 at kernel/cgroup_pids.c:97 pids_cancel.constprop.6+0x31/0x40() Modules linked in: CPU: 1 PID: 1 Comm: systemd Not tainted 4.4.0-rc1+ #29 ... ffffffff81f65382 ffff88007c043b90 ffffffff81551ffc 0000000000000000 ffff88007c043bc8 ffffffff810de202 ffff88007a752000 ffff88007a29ab00 ffff88007c043c80 ffff88007a1d8400 0000000000000001 ffff88007c043bd8 Call Trace: [<ffffffff81551ffc>] dump_stack+0x4e/0x82 [<ffffffff810de202>] warn_slowpath_common+0x82/0xc0 [<ffffffff810de2fa>] warn_slowpath_null+0x1a/0x20 [<ffffffff8118e031>] pids_cancel.constprop.6+0x31/0x40 [<ffffffff8118e0fd>] pids_can_attach+0x6d/0xf0 [<ffffffff81188a4c>] cgroup_taskset_migrate+0x6c/0x330 [<ffffffff81188e05>] cgroup_migrate+0xf5/0x190 [<ffffffff81189016>] cgroup_attach_task+0x176/0x200 [<ffffffff8118949d>] __cgroup_procs_write+0x2ad/0x460 [<ffffffff81189684>] cgroup_procs_write+0x14/0x20 [<ffffffff811854e5>] cgroup_file_write+0x35/0x1c0 [<ffffffff812e26f1>] kernfs_fop_write+0x141/0x190 [<ffffffff81265f88>] __vfs_write+0x28/0xe0 [<ffffffff812666fc>] vfs_write+0xac/0x1a0 [<ffffffff81267019>] SyS_write+0x49/0xb0 [<ffffffff81bcef32>] entry_SYSCALL_64_fastpath+0x12/0x76 This patch fixes the bug by removing @css parameter from the three migration methods, ->can_attach, ->cancel_attach() and ->attach() and updating cgroup_taskset iteration helpers also return the destination css in addition to the task being migrated. All controllers are updated accordingly. * Controllers which don't care whether there are one or multiple target csses can be converted trivially. cpu, io, freezer, perf, netclassid and netprio fall in this category. * cpuset's current implementation assumes that there's single source and destination and thus doesn't support v2 hierarchy already. The only change made by this patchset is how that single destination css is obtained. * memory migration path already doesn't do anything on v2. How the single destination css is obtained is updated and the prep stage of mem_cgroup_can_attach() is reordered to accomodate the change. * pids is the only controller which was affected by this bug. It now correctly handles multi-destination migrations and no longer causes counter underflow from incorrect accounting. Signed-off-by: Tejun Heo <tj@kernel.org> Reported-and-tested-by: Daniel Wagner <daniel.wagner@bmw-carit.de> Cc: Aleksa Sarai <cyphar@cyphar.com>
2015-11-05Merge branch 'for-4.4' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup Pull cgroup updates from Tejun Heo: "The cgroup core saw several significant updates this cycle: - percpu_rwsem for threadgroup locking is reinstated. This was temporarily dropped due to down_write latency issues. Oleg's rework of percpu_rwsem which is scheduled to be merged in this merge window resolves the issue. - On the v2 hierarchy, when controllers are enabled and disabled, all operations are atomic and can fail and revert cleanly. This allows ->can_attach() failure which is necessary for cpu RT slices. - Tasks now stay associated with the original cgroups after exit until released. This allows tracking resources held by zombies (e.g. pids) and makes it easy to find out where zombies came from on the v2 hierarchy. The pids controller was broken before these changes as zombies escaped the limits; unfortunately, updating this behavior required too many invasive changes and I don't think it's a good idea to backport them, so the pids controller on 4.3, the first version which included the pids controller, will stay broken at least until I'm sure about the cgroup core changes. - Optimization of a couple common tests using static_key" * 'for-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup: (38 commits) cgroup: fix race condition around termination check in css_task_iter_next() blkcg: don't create "io.stat" on the root cgroup cgroup: drop cgroup__DEVEL__legacy_files_on_dfl cgroup: replace error handling in cgroup_init() with WARN_ON()s cgroup: add cgroup_subsys->free() method and use it to fix pids controller cgroup: keep zombies associated with their original cgroups cgroup: make css_set_rwsem a spinlock and rename it to css_set_lock cgroup: don't hold css_set_rwsem across css task iteration cgroup: reorganize css_task_iter functions cgroup: factor out css_set_move_task() cgroup: keep css_set and task lists in chronological order cgroup: make cgroup_destroy_locked() test cgroup_is_populated() cgroup: make css_sets pin the associated cgroups cgroup: relocate cgroup_[try]get/put() cgroup: move check_for_release() invocation cgroup: replace cgroup_has_tasks() with cgroup_is_populated() cgroup: make cgroup->nr_populated count the number of populated css_sets cgroup: remove an unused parameter from cgroup_task_migrate() cgroup: fix too early usage of static_branch_disable() cgroup: make cgroup_update_dfl_csses() migrate all target processes atomically ...
2015-10-22blkcg: don't create "io.stat" on the root cgroupTejun Heo
The stat files on the root cgroup shows stats for the whole system and usually don't contain any information which isn't available through the usual system monitoring mechanisms. Some controllers skip collecting these duplicate stats to optimize cases where cgroup isn't used and later try to emulate the result on demand. This leads to complexities and subtle differences in the information shown through different channels. This is entirely unnecessary and cgroup v2 is dropping stat files which are duplicate from all controllers. This patch removes "io.stat" from the root hierarchy. Signed-off-by: Tejun Heo <tj@kernel.org> Acked-by: Jens Axboe <axboe@kernel.dk> Cc: Vivek Goyal <vgoyal@redhat.com>
2015-09-19Merge branch 'for-linus' of git://git.kernel.dk/linux-blockLinus Torvalds
Pull block updates from Jens Axboe: "This is a bit bigger than it should be, but I could (did) not want to send it off last week due to both wanting extra testing, and expecting a fix for the bounce regression as well. In any case, this contains: - Fix for the blk-merge.c compilation warning on gcc 5.x from me. - A set of back/front SG gap merge fixes, from me and from Sagi. This ensures that we honor SG gapping for integrity payloads as well. - Two small fixes for null_blk from Matias, fixing a leak and a capacity propagation issue. - A blkcg fix from Tejun, fixing a NULL dereference. - A fast clone optimization from Ming, fixing a performance regression since the arbitrarily sized bio's were introduced. - Also from Ming, a regression fix for bouncing IOs" * 'for-linus' of git://git.kernel.dk/linux-block: block: fix bounce_end_io block: blk-merge: fast-clone bio when splitting rw bios block: blkg_destroy_all() should clear q->root_blkg and ->root_rl.blkg block: Copy a user iovec if it includes gaps block: Refuse adding appending a gapped integrity page to a bio block: Refuse request/bio merges with gaps in the integrity payload block: Check for gaps on front and back merges null_blk: fix wrong capacity when bs is not 512 bytes null_blk: fix memory leak on cleanup block: fix bogus compiler warnings in blk-merge.c
2015-09-11block: blkg_destroy_all() should clear q->root_blkg and ->root_rl.blkgTejun Heo
While making the root blkg unconditional, ec13b1d6f0a0 ("blkcg: always create the blkcg_gq for the root blkcg") removed the part which clears q->root_blkg and ->root_rl.blkg during q exit. This leaves the two pointers dangling after blkg_destroy_all(). blk-throttle exit path performs blkg traversals and dereferences ->root_blkg and can lead to the following oops. BUG: unable to handle kernel NULL pointer dereference at 0000000000000558 IP: [<ffffffff81389746>] __blkg_lookup+0x26/0x70 ... task: ffff88001b4e2580 ti: ffff88001ac0c000 task.ti: ffff88001ac0c000 RIP: 0010:[<ffffffff81389746>] [<ffffffff81389746>] __blkg_lookup+0x26/0x70 ... Call Trace: [<ffffffff8138d14a>] blk_throtl_drain+0x5a/0x110 [<ffffffff8138a108>] blkcg_drain_queue+0x18/0x20 [<ffffffff81369a70>] __blk_drain_queue+0xc0/0x170 [<ffffffff8136a101>] blk_queue_bypass_start+0x61/0x80 [<ffffffff81388c59>] blkcg_deactivate_policy+0x39/0x100 [<ffffffff8138d328>] blk_throtl_exit+0x38/0x50 [<ffffffff8138a14e>] blkcg_exit_queue+0x3e/0x50 [<ffffffff8137016e>] blk_release_queue+0x1e/0xc0 ... While the bug is a straigh-forward use-after-free bug, it is tricky to reproduce because blkg release is RCU protected and the rest of exit path usually finishes before RCU grace period. This patch fixes the bug by updating blkg_destro_all() to clear q->root_blkg and ->root_rl.blkg. Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: "Richard W.M. Jones" <rjones@redhat.com> Reported-by: Josh Boyer <jwboyer@fedoraproject.org> Link: http://lkml.kernel.org/g/CA+5PVA5rzQ0s4723n5rHBcxQa9t0cW8BPPBekr_9aMRoWt2aYg@mail.gmail.com Fixes: ec13b1d6f0a0 ("blkcg: always create the blkcg_gq for the root blkcg") Cc: stable@vger.kernel.org # v4.2+ Tested-by: Richard W.M. Jones <rjones@redhat.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2015-08-18blkcg: use CGROUP_WEIGHT_* scale for io.weight on the unified hierarchyTejun Heo
cgroup is trying to make interface consistent across different controllers. For weight based resource control, the knob should have the range [1, 10000] and default to 100. This patch updates cfq-iosched so that the weight range conforms. The internal calculations have enough range and the widening of the weight range shouldn't cause any problem. * blkcg_policy->cpd_bind_fn() is added. If present, this is invoked when blkcg is attached to a hierarchy. * cfq_cpd_init() is updated to use the new default value on the unified hierarchy. * cfq_cpd_bind() callback is implemented to clear per-blkg configs and apply the default config matching the hierarchy type. * cfqd->root_group->[leaf_]weight initialization in cfq_init_queue() is moved into !CONFIG_CFQ_GROUP_IOSCHED block. cfq_cpd_bind() is now responsible for initializing the initial weights when blkcg is enabled. Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Arianna Avanzini <avanzini.arianna@gmail.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2015-08-18blkcg: implement interface for the unified hierarchyTejun Heo
blkcg interface grew to be the biggest of all controllers and unfortunately most inconsistent too. The interface files are inconsistent with a number of cloes duplicates. Some files have recursive variants while others don't. There's distinction between normal and leaf weights which isn't intuitive and there are a lot of stat knobs which don't make much sense outside of debugging and expose too much implementation details to userland. In the unified hierarchy, everything is always hierarchical and internal nodes can't have tasks rendering the two structural issues twisting the current interface. The interface has to be updated in a significant anyway and this is a good chance to revamp it as a whole. This patch implements blkcg interface for the unified hierarchy. * (from a previous patch) blkcg is identified by "io" instead of "blkio" on the unified hierarchy. Given that the whole interface is updated anyway, the rename shouldn't carry noticeable conversion overhead. * The original interface consisted of 27 files is replaced with the following three files. blkio.stat : per-blkcg stats blkio.weight : per-cgroup and per-cgroup-queue weight settings blkio.max : per-cgroup-queue bps and iops max limits Documentation/cgroups/unified-hierarchy.txt updated accordingly. v2: blkcg_policy->dfl_cftypes wasn't removed on blkcg_policy_unregister() corrupting the cftypes list. Fixed. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jens Axboe <axboe@fb.com>
2015-08-18blkcg: misc preparations for unified hierarchy interfaceTejun Heo
* Export blkg_dev_name() * Drop unnecessary @cft from __cfq_set_weight(). Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jens Axboe <axboe@fb.com>
2015-08-18blkcg: move body parsing from blkg_conf_prep() to its callersTejun Heo
Currently, blkg_conf_prep() expects input to be of the following form MAJ:MIN NUM and reads the NUM part into blkg_conf_ctx->v. This is quite restrictive and gets in the way in implementing blkcg interface for the unified hierarchy. This patch updates blkg_conf_prep() so that it expects MAJ:MIN BODY_STR where BODY_STR is an arbitrary string. blkg_conf_ctx->v is replaced with ->body which is a char pointer pointing to the start of BODY_STR. Parsing of the body is moved to blkg_conf_prep()'s callers. To allow using, for example, strsep() on blkg_conf_ctx->val, it is a non-const pointer and to accommodate that const is dropped from @input too. This doesn't cause any behavior changes. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jens Axboe <axboe@fb.com>
2015-08-18blkcg: mark existing cftypes as legacyTejun Heo
blkcg is about to grow interface for the unified hierarchy. Add legacy to existing cftypes. * blkcg_policy->cftypes -> blkcg_policy->legacy_cftypes * blk-cgroup.c:blkcg_files -> blkcg_legacy_files * cfq-iosched.c:cfq_blkcg_files -> cfq_blkcg_legacy_files * blk-throttle.c:throtl_files -> throtl_legacy_files Pure renames. No functional change. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jens Axboe <axboe@fb.com>
2015-08-18blkcg: rename subsystem name from blkio to ioTejun Heo
blkio interface has become messy over time and is currently the largest. In addition to the inconsistent naming scheme, it has multiple stat files which report more or less the same thing, a number of debug stat files which expose internal details which shouldn't have been part of the public interface in the first place, recursive and non-recursive stats and leaf and non-leaf knobs. Both recursive vs. non-recursive and leaf vs. non-leaf distinctions don't make any sense on the unified hierarchy as only leaf cgroups can contain processes. cgroups is going through a major interface revision with the unified hierarchy involving significant fundamental usage changes and given that a significant portion of the interface doesn't make sense anymore, it's a good time to reorganize the interface. As the first step, this patch renames the external visible subsystem name from "blkio" to "io". This is more concise, matches the other two major subsystem names, "cpu" and "memory", and better suited as blkcg will be involved in anything writeback related too whether an actual block device is involved or not. As the subsystem legacy_name is set to "blkio", the only userland visible change outside the unified hierarchy is that blkcg is reported as "io" instead of "blkio" in the subsystem initialized message during boot. On the unified hierarchy, blkcg now appears as "io". Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Li Zefan <lizefan@huawei.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: cgroups@vger.kernel.org Signed-off-by: Jens Axboe <axboe@fb.com>
2015-08-18blkcg: refine error codes returned during blkcg configurationTejun Heo
blkcg currently returns -EINVAL for most errors which can be pretty confusing given that the failure modes are quite varied. Update the error returns so that * -EINVAL only for syntactic errors. * -ERANGE if the value is out of range. * -ENODEV if the target device can't be found. * -EOPNOTSUPP if the policy is not enabled on the target device. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jens Axboe <axboe@fb.com>
2015-08-18blkcg: reduce stack usage of blkg_rwstat_recursive_sum()Tejun Heo
The recent percpu conversion of blkg_rwstat triggered the following warning in certain configurations. block/blk-cgroup.c:654:1: warning: the frame size of 1360 bytes is larger than 1024 bytes This is because blkg_rwstat now contains four percpu_counter which can be pretty big depending on debug options although it shouldn't be a problem in production configs. This patch removes one of the two local blkg_rwstat variables used by blkg_rwstat_recursive_sum() to reduce stack usage. Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Vivek Goyal <vgoyal@redhat.com> Reported-by: kbuild test robot <fengguang.wu@intel.com> Link: http://article.gmane.org/gmane.linux.kernel.cgroups/13835 Signed-off-by: Jens Axboe <axboe@fb.com>
2015-08-18blkcg: move io_service_bytes and io_serviced stats into blkcg_gqTejun Heo
Currently, both cfq-iosched and blk-throttle keep track of io_service_bytes and io_serviced stats. While keeping track of them separately may be useful during development, it doesn't make much sense otherwise. Also, blk-throttle was counting bio's as IOs while cfq-iosched request's, which is more confusing than informative. This patch adds ->stat_bytes and ->stat_ios to blkg (blkcg_gq), removes the counterparts from cfq-iosched and blk-throttle and let them print from the common blkg counters. The common counters are incremented during bio issue in blkcg_bio_issue_check(). The outputs are still filtered by whether the policy has blkg_policy_data on a given blkg, so cfq's output won't show up if it has never been used for a given blkg. The only times when the outputs would differ significantly are when policies are attached on the fly or elevators are switched back and forth. Those are quite exceptional operations and I don't think they warrant keeping separate counters. v3: Update blkio-controller.txt accordingly. v2: Account IOs during bio issues instead of request completions so that bio-based drivers can be handled the same way. Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Vivek Goyal <vgoyal@redhat.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2015-08-18blkcg: make blkg_[rw]stat_recursive_sum() to be able to index into blkcg_gqTejun Heo
Currently, blkg_[rw]stat_recursive_sum() assume that the target counter is located in pd (blkg_policy_data); however, some counters are planned to be moved to blkg (blkcg_gq). This patch updates blkg_[rw]stat_recursive_sum() to take blkg and blkg_policy pointers instead of pd. If policy is NULL, it indexes into blkg. If non-NULL, into the blkg's pd of the policy. The existing usages are updated to maintain the current behaviors. Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Vivek Goyal <vgoyal@redhat.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2015-08-18blkcg: make blkcg_[rw]stat per-cpuTejun Heo
blkcg_[rw]stat are used as stat counters for blkcg policies. It isn't per-cpu by itself and blk-throttle makes it per-cpu by wrapping around it. This patch makes blkcg_[rw]stat per-cpu and drop the ad-hoc per-cpu wrapping in blk-throttle. * blkg_[rw]stat->cnt is replaced with cpu_cnt which is struct percpu_counter. This makes syncp unnecessary as remote accesses are handled by percpu_counter itself. * blkg_[rw]stat_init() can now fail due to percpu allocation failure and thus are updated to return int. * percpu_counters need explicit freeing. blkg_[rw]stat_exit() added. * As blkg_rwstat->cpu_cnt[] can't be read directly anymore, reading and summing results are stored in ->aux_cnt[] instead. * Custom per-cpu stat implementation in blk-throttle is removed. This makes all blkcg stat counters per-cpu without complicating policy implmentations. Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Vivek Goyal <vgoyal@redhat.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2015-08-18blkcg: add blkg_[rw]stat->aux_cnt and replace cfq_group->dead_stats with itTejun Heo
cgroup stats are local to each cgroup and doesn't propagate to ancestors by default. When recursive stats are necessary, the sum is calculated over all the descendants. This initially was for backward compatibility to support both group-local and recursive stats but this mode of operation makes general sense as stat update is much hotter thafn reporting those stats. This however ends up losing recursive stats when a child is removed. To work around this, cfq-iosched adds its stats to its parent cfq_group->dead_stats which is summed up together when calculating recursive stats. It's planned that the core stats will be moved to blkcg_gq, so we want to move the mechanism for keeping track of the stats of dead children from cfq to blkcg core. This patch adds blkg_[rw]stat->aux_cnt which are atomic64_t's keeping track of auxiliary counts which are excluded when reading local counts but included for recursive. blkg_[rw]stat_merge() which were used by cfq to implement dead_stats are replaced by blkg_[rw]stat_add_aux(), and cfq now forwards stats of a dead cgroup to the aux counts of parent->stats instead of separate ->dead_stats. This will also help making blkg_[rw]stats per-cpu. Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Vivek Goyal <vgoyal@redhat.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2015-08-18blkcg: consolidate blkg creation in blkcg_bio_issue_check()Tejun Heo
blkg (blkcg_gq) currently is created by blkcg policies invoking blkg_lookup_create() which ends up repeating about the same code in different policies. Theoretically, this can avoid the overhead of looking and/or creating blkg's if blkcg is enabled but no policy is in use; however, the cost of blkg lookup / creation is very low especially if only the root blkcg is in use which is highly likely if no blkcg policy is in active use - it boils down to a single very predictable conditional and surrounding RCU protection. This patch consolidates blkg creation to a new function blkcg_bio_issue_check() which is called during bio issue from generic_make_request_checks(). blkcg_bio_issue_check() is now the only function which tries to create missing blkg's. The subsequent policy and request_list operations just perform blkg_lookup() and if missing falls back to the root. * blk_get_rl() no longer tries to create blkg. It uses blkg_lookup() instead of blkg_lookup_create(). * blk_throtl_bio() is now called from blkcg_bio_issue_check() with rcu read locked and blkg already looked up. Both throtl_lookup_tg() and throtl_lookup_create_tg() are dropped. * cfq is similarly updated. cfq_lookup_create_cfqg() is replaced with cfq_lookup_cfqg()which uses blkg_lookup(). This consolidates blkg handling and avoids unnecessary blkg creation retries under memory pressure. In addition, this provides a common bio entry point into blkcg where things like common accounting can be performed. v2: Build fixes for !CONFIG_CFQ_GROUP_IOSCHED and !CONFIG_BLK_DEV_THROTTLING. Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Arianna Avanzini <avanzini.arianna@gmail.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2015-08-18blkcg: inline [__]blkg_lookup()Tejun Heo
blkg_lookup() checks whether the target queue is bypassing and, if not, calls __blkg_lookup() which first checks the lookup hint and then performs radix tree walk. The operations upto hint checking are trivial and there are many users of this function. This patch inlines blkg_lookup() and the fast path part of __blkg_lookup(). The radix tree lookup and hint update are now in blkg_lookup_slowpath(). This will help consolidating blkg handling by easing moving root blkcg short-circuit to inlined lookup fast path. Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Arianna Avanzini <avanzini.arianna@gmail.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2015-08-18blkcg: replace blkcg_policy->cpd_size with ->cpd_alloc/free_fn() methodsTejun Heo
Each active policy has a cpd (blkcg_policy_data) on each blkcg. The cpd's were allocated by blkcg core and each policy could request to allocate extra space at the end by setting blkcg_policy->cpd_size larger than the size of cpd. This is a bit unusual but blkg (blkcg_gq) policy data used to be handled this way too so it made sense to be consistent; however, blkg policy data switched to alloc/free callbacks. This patch makes similar changes to cpd handling. blkcg_policy->cpd_alloc/free_fn() are added to replace ->cpd_size. As cpd allocation is now done from policy side, it can simply allocate a larger area which embeds cpd at the beginning. As ->cpd_alloc_fn() may be able to perform all necessary initializations, this patch makes ->cpd_init_fn() optional. Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Arianna Avanzini <avanzini.arianna@gmail.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2015-08-18blkcg: minor updates around blkcg_policy_dataTejun Heo
* Rename blkcg->pd[] to blkcg->cpd[] so that cpd is consistently used for blkcg_policy_data. * Make blkcg_policy->cpd_init_fn() take blkcg_policy_data instead of blkcg. This makes it consistent with blkg_policy_data methods and to-be-added cpd alloc/free methods. * blkcg_policy_data->blkcg and cpd_to_blkcg() added so that cpd_init_fn() can determine the associated blkcg from blkcg_policy_data. v2: blkcg_policy_data->blkcg initializations were missing. Added. Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Arianna Avanzini <avanzini.arianna@gmail.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2015-08-18blkcg: make blkcg_policy methods take a pointer to blkcg_policy_dataTejun Heo
The newly added ->pd_alloc_fn() and ->pd_free_fn() deal with pd (blkg_policy_data) while the older ones use blkg (blkcg_gq). As using blkg doesn't make sense for ->pd_alloc_fn() and after allocation pd can always be mapped to blkg and given that these are policy-specific methods, it makes sense to converge on pd. This patch makes all methods deal with pd instead of blkg. Most conversions are trivial. In blk-cgroup.c, a couple method invocation sites now test whether pd exists instead of policy state for consistency. This shouldn't cause any behavioral differences. Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Vivek Goyal <vgoyal@redhat.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2015-08-18blk-throttle: clean up blkg_policy_data alloc/init/exit/free methodsTejun Heo
With the recent addition of alloc and free methods, things became messier. This patch reorganizes them according to the followings. * ->pd_alloc_fn() Responsible for allocation and static initializations - the ones which can be done independent of where the pd might be attached. * ->pd_init_fn() Initializations which require the knowledge of where the pd is attached. * ->pd_free_fn() The counter part of pd_alloc_fn(). Static de-init and freeing. This leaves ->pd_exit_fn() without any users. Removed. While at it, collapse an one liner function throtl_pd_exit(), which has only one user, into its user. Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Vivek Goyal <vgoyal@redhat.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2015-08-18blkcg: replace blkcg_policy->pd_size with ->pd_alloc/free_fn() methodsTejun Heo
A blkg (blkcg_gq) represents the relationship between a cgroup and request_queue. Each active policy has a pd (blkg_policy_data) on each blkg. The pd's were allocated by blkcg core and each policy could request to allocate extra space at the end by setting blkcg_policy->pd_size larger than the size of pd. This is a bit unusual but was done this way mostly to simplify error handling and all the existing use cases could be handled this way; however, this is becoming too restrictive now that percpu memory can be allocated without blocking. This introduces two new mandatory blkcg_policy methods - pd_alloc_fn() and pd_free_fn() - which are used to allocate and release pd for a given policy. As pd allocation is now done from policy side, it can simply allocate a larger area which embeds pd at the beginning. This change makes ->pd_size pointless. Removed. Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Vivek Goyal <vgoyal@redhat.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2015-08-18blkcg: make blkcg_activate_policy() allow NULL ->pd_init_fnTejun Heo
blkg_create() allows NULL ->pd_init_fn() but blkcg_activate_policy() doesn't. As both in-kernel policies implement ->pd_init_fn, it currently doesn't break anything. Update blkcg_activate_policy() so that its behavior is consistent with blkg_create(). Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Vivek Goyal <vgoyal@redhat.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2015-08-18blkcg: restructure blkg_policy_data allocation in blkcg_activate_policy()Tejun Heo
When a policy gets activated, it needs to allocate and install its policy data on all existing blkg's (blkcg_gq's). Because blkg iteration is protected by a spinlock, it currently counts the total number of blkg's in the system, allocates the matching number of policy data on a list and installs them during a single iteration. This can be simplified by using speculative GFP_NOWAIT allocations while iterating and falling back to a preallocated policy data on failure. If the preallocated one has already been consumed, it releases the lock, preallocate with GFP_KERNEL and then restarts the iteration. This can be a bit more expensive than before but policy activation is a very cold path and shouldn't matter. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jens Axboe <axboe@fb.com>
2015-08-18blkcg: remove unnecessary blkcg_root handling from css_alloc/free pathsTejun Heo
blkcg_css_alloc() bypasses policy data allocation and blkcg_css_free() bypasses policy data and blkcg freeing for blkcg_root. There's no reason to to treat policy data any differently for blkcg_root. If the root css gets allocated after policies are registered, policy registration path will add policy data; otherwise, the alloc path will. The free path isn't never invoked for root csses. This patch removes the unnecessary special handling of blkcg_root from css_alloc/free paths. Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Vivek Goyal <vgoyal@redhat.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2015-08-18blkcg: use blkg_free() in blkcg_init_queue() failure pathTejun Heo
When blkcg_init_queue() fails midway after creating a new blkg, it performs kfree() directly; however, this doesn't free the policy data areas. Make it use blkg_free() instead. In turn, blkg_free() is updated to handle root request_list special case. While this fixes a possible memory leak, it's on an unlikely failure path of an already cold path and the size leaked per occurrence is miniscule too. I don't think it needs to be tagged for -stable. Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Vivek Goyal <vgoyal@redhat.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2015-08-18blkcg, cfq-iosched: use GFP_NOWAIT instead of GFP_ATOMIC for non-critical ↵Tejun Heo
allocations blkcg performs several allocations to track IOs per cgroup and enforce resource control. Most of these allocations are performed lazily on demand in the IO path and thus can't involve reclaim path. Currently, these allocations use GFP_ATOMIC; however, blkcg can gracefully deal with occassional failures of these allocations by punting IOs to the root cgroup and there's no reason to reach into the emergency reserve. This patch replaces GFP_ATOMIC with GFP_NOWAIT for the following allocations. * bdi_writeback_congested and blkcg_gq allocations in blkg_create(). * radix tree node allocations for blkcg->blkg_tree. * cfq_queue allocation on ioprio changes. Signed-off-by: Tejun Heo <tj@kernel.org> Suggested-and-Reviewed-by: Jeff Moyer <jmoyer@redhat.com> Suggested-by: Vivek Goyal <vgoyal@redhat.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2015-07-22blkcg: fix gendisk reference leak in blkg_conf_prep()Tejun Heo
When a blkcg configuration is targeted to a partition rather than a whole device, blkg_conf_prep fails with -EINVAL; unfortunately, it forgets to put the gendisk ref in that case. Fix it. Signed-off-by: Tejun Heo <tj@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Jens Axboe <axboe@fb.com>
2015-07-09blkcg: fix blkcg_policy_data allocation bugTejun Heo
e48453c386f3 ("block, cgroup: implement policy-specific per-blkcg data") updated per-blkcg policy data to be dynamically allocated. When a policy is registered, its policy data aren't created. Instead, when the policy is activated on a queue, the policy data are allocated if there are blkg's (blkcg_gq's) which are attached to a given blkcg. This is buggy. Consider the following scenario. 1. A blkcg is created. No blkg's attached yet. 2. The policy is registered. No policy data is allocated. 3. The policy is activated on a queue. As the above blkcg doesn't have any blkg's, it won't allocate the matching blkcg_policy_data. 4. An IO is issued from the blkcg and blkg is created and the blkcg still doesn't have the matching policy data allocated. With cfq-iosched, this leads to an oops. It also doesn't free policy data on policy unregistration assuming that freeing of all policy data on blkcg destruction should take care of it; however, this also is incorrect. 1. A blkcg has policy data. 2. The policy gets unregistered but the policy data remains. 3. Another policy gets registered on the same slot. 4. Later, the new policy tries to allocate policy data on the previous blkcg but the slot is already occupied and gets skipped. The policy ends up operating on the policy data of the previous policy. There's no reason to manage blkcg_policy_data lazily. The reason we do lazy allocation of blkg's is that the number of all possible blkg's is the product of cgroups and block devices which can reach a surprising level. blkcg_policy_data is contrained by the number of cgroups and shouldn't be a problem. This patch makes blkcg_policy_data to be allocated for all existing blkcg's on policy registration and freed on unregistration and removes blkcg_policy_data handling from policy [de]activation paths. This makes that blkcg_policy_data are created and removed with the policy they belong to and fixes the above described problems. Signed-off-by: Tejun Heo <tj@kernel.org> Fixes: e48453c386f3 ("block, cgroup: implement policy-specific per-blkcg data") Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Arianna Avanzini <avanzini.arianna@gmail.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2015-07-09blkcg: implement all_blkcgs listTejun Heo
Add all_blkcgs list goes through blkcg->all_blkcgs_node and is protected by blkcg_pol_mutex. This will be used to fix blkcg_policy_data allocation bug. Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Arianna Avanzini <avanzini.arianna@gmail.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2015-07-09blkcg: blkcg_css_alloc() should grab blkcg_pol_mutex while iterating ↵Tejun Heo
blkcg_policy[] An entry in blkcg_policy[] is stable while there are non-bypassing in-flight IOs on a request_queue which has the policy activated. This is why most derefs of blkcg_policy[] don't need explicit locking; however, blkcg_css_alloc() isn't invoked from IO path and thus doesn't have this protection and may race policies being added and removed. Fix it by adding explicit blkcg_pol_mutex protection around blkcg_policy[] iteration in blkcg_css_alloc(). Signed-off-by: Tejun Heo <tj@kernel.org> Fixes: e48453c386f3 ("block, cgroup: implement policy-specific per-blkcg data") Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Arianna Avanzini <avanzini.arianna@gmail.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2015-07-09blkcg: allow blkcg_pol_mutex to be grabbed from cgroup [file] methodsTejun Heo
blkcg_pol_mutex primarily protects the blkcg_policy array. It also protects cgroup file type [un]registration during policy addition / removal. This puts blkcg_pol_mutex outside cgroup internal synchronization and in turn makes it impossible to grab from blkcg's cgroup methods as that leads to cyclic dependency. Another problematic dependency arising from this is through cgroup interface file deactivation. Removing a cftype requires removing all files of the type which in turn involves draining all on-going invocations of the file methods. This means that an interface file implementation can't grab blkcg_pol_mutex as draining can lead to AA deadlock. blkcg_reset_stats() is already in this situation. It currently trylocks blkcg_pol_mutex and then unwinds and retries the whole operation on failure, which is cumbersome at best. It has a lengthy comment explaining how cgroup internal synchronization is involved and expected to be updated but as explained above this doesn't need cgroup internal locking to deadlock. It's a self-contained AA deadlock. The described circular dependencies can be easily broken by moving cftype [un]registration out of blkcg_pol_mutex and protect them with an outer mutex. This patch introduces blkcg_pol_register_mutex which wraps entire policy [un]registration including cftype operations and shrinks blkcg_pol_mutex critical section. This also makes the trylock dancing in blkcg_reset_stats() unnecessary. Removed. This patch is necessary for the following blkcg_policy_data allocation bug fixes. Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Arianna Avanzini <avanzini.arianna@gmail.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2015-07-07block/blk-cgroup.c: free per-blkcg data when freeing the blkcgArianna Avanzini
Currently, per-blkcg data is freed each time a policy is deactivated, that is also upon scheduler switch. However, when switching from a scheduler implementing a policy which requires per-blkcg data to another one, that same policy might be active on other devices, and therefore those same per-blkcg data could be still in use. This commit lets per-blkcg data be freed when the blkcg is freed instead of on policy deactivation. Signed-off-by: Arianna Avanzini <avanzini.arianna@gmail.com> Reported-and-tested-by: Michael Kaminsky <kaminsky@cs.cmu.edu> Fixes: e48453c3 ("block, cgroup: implement policy-specific per-blkcg data") Signed-off-by: Jens Axboe <axboe@fb.com>
2015-06-25Merge branch 'for-4.2/writeback' of git://git.kernel.dk/linux-blockLinus Torvalds
Pull cgroup writeback support from Jens Axboe: "This is the big pull request for adding cgroup writeback support. This code has been in development for a long time, and it has been simmering in for-next for a good chunk of this cycle too. This is one of those problems that has been talked about for at least half a decade, finally there's a solution and code to go with it. Also see last weeks writeup on LWN: http://lwn.net/Articles/648292/" * 'for-4.2/writeback' of git://git.kernel.dk/linux-block: (85 commits) writeback, blkio: add documentation for cgroup writeback support vfs, writeback: replace FS_CGROUP_WRITEBACK with SB_I_CGROUPWB writeback: do foreign inode detection iff cgroup writeback is enabled v9fs: fix error handling in v9fs_session_init() bdi: fix wrong error return value in cgwb_create() buffer: remove unusued 'ret' variable writeback: disassociate inodes from dying bdi_writebacks writeback: implement foreign cgroup inode bdi_writeback switching writeback: add lockdep annotation to inode_to_wb() writeback: use unlocked_inode_to_wb transaction in inode_congested() writeback: implement unlocked_inode_to_wb transaction and use it for stat updates writeback: implement [locked_]inode_to_wb_and_lock_list() writeback: implement foreign cgroup inode detection writeback: make writeback_control track the inode being written back writeback: relocate wb[_try]_get(), wb_put(), inode_{attach|detach}_wb() mm: vmscan: disable memcg direct reclaim stalling if cgroup writeback support is in use writeback: implement memcg writeback domain based throttling writeback: reset wb_domain->dirty_limit[_tstmp] when memcg domain size changes writeback: implement memcg wb_domain writeback: update wb_over_bg_thresh() to use wb_domain aware operations ...
2015-06-07block, cgroup: implement policy-specific per-blkcg dataArianna Avanzini
The block IO (blkio) controller enables the block layer to provide service guarantees in a hierarchical fashion. Specifically, service guarantees are provided by registered request-accounting policies. As of now, a proportional-share and a throttling policy are available. They are implemented, respectively, by the CFQ I/O scheduler and the blk-throttle subsystem. Unfortunately, as for adding new policies, the current implementation of the block IO controller is only halfway ready to allow new policies to be plugged in. This commit provides a solution to make the block IO controller fully ready to handle new policies. In what follows, we first describe briefly the current state, and then list the changes made by this commit. The throttling policy does not need any per-cgroup information to perform its task. In contrast, the proportional share policy uses, for each cgroup, both the weight assigned by the user to the cgroup, and a set of dynamically- computed weights, one for each device. The first, user-defined weight is stored in the blkcg data structure: the block IO controller allocates a private blkcg data structure for each cgroup in the blkio cgroups hierarchy (regardless of which policy is active). In other words, the block IO controller internally mirrors the blkio cgroups with private blkcg data structures. On the other hand, for each cgroup and device, the corresponding dynamically- computed weight is maintained in the following, different way. For each device, the block IO controller keeps a private blkcg_gq structure for each cgroup in blkio. In other words, block IO also keeps one private mirror copy of the blkio cgroups hierarchy for each device, made of blkcg_gq structures. Each blkcg_gq structure keeps per-policy information in a generic array of dynamically-allocated 'dedicated' data structures, one for each registered policy (so currently the array contains two elements). To be inserted into the generic array, each dedicated data structure embeds a generic blkg_policy_data structure. Consider now the array contained in the blkcg_gq structure corresponding to a given pair of cgroup and device: one of the elements of the array contains the dedicated data structure for the proportional-share policy, and this dedicated data structure contains the dynamically-computed weight for that pair of cgroup and device. The generic strategy adopted for storing per-policy data in blkcg_gq structures is already capable of handling new policies, whereas the one adopted with blkcg structures is not, because per-policy data are hard-coded in the blkcg structures themselves (currently only data related to the proportional- share policy). This commit addresses the above issues through the following changes: . It generalizes blkcg structures so that per-policy data are stored in the same way as in blkcg_gq structures. Specifically, it lets also the blkcg structure store per-policy data in a generic array of dynamically-allocated dedicated data structures. We will refer to these data structures as blkcg dedicated data structures, to distinguish them from the dedicated data structures inserted in the generic arrays kept by blkcg_gq structures. To allow blkcg dedicated data structures to be inserted in the generic array inside a blkcg structure, this commit also introduces a new blkcg_policy_data structure, which is the equivalent of blkg_policy_data for blkcg dedicated data structures. . It adds to the blkcg_policy structure, i.e., to the descriptor of a policy, a cpd_size field and a cpd_init field, to be initialized by the policy with, respectively, the size of the blkcg dedicated data structures, and the address of a constructor function for blkcg dedicated data structures. . It moves the CFQ-specific fields embedded in the blkcg data structure (i.e., the fields related to the proportional-share policy), into a new blkcg dedicated data structure called cfq_group_data. Signed-off-by: Paolo Valente <paolo.valente@unimore.it> Signed-off-by: Arianna Avanzini <avanzini.arianna@gmail.com> Acked-by: Tejun Heo <tj@kernel.org> Cc: Jens Axboe <axboe@fb.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2015-06-02writeback, blkcg: associate each blkcg_gq with the corresponding ↵Tejun Heo
bdi_writeback_congested A blkg (blkcg_gq) can be congested and decongested independently from other blkgs on the same request_queue. Accordingly, for cgroup writeback support, the congestion status at bdi (backing_dev_info) should be split and updated separately from matching blkg's. This patch prepares by adding blkg->wb_congested and associating a blkg with its matching per-blkcg bdi_writeback_congested on creation. v2: Updated to associate bdi_writeback_congested instead of bdi_writeback. Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jan Kara <jack@suse.cz> Cc: Vivek Goyal <vgoyal@redhat.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2015-06-02writeback: make backing_dev_info host cgroup-specific bdi_writebacksTejun Heo
For the planned cgroup writeback support, on each bdi (backing_dev_info), each memcg will be served by a separate wb (bdi_writeback). This patch updates bdi so that a bdi can host multiple wbs (bdi_writebacks). On the default hierarchy, blkcg implicitly enables memcg. This allows using memcg's page ownership for attributing writeback IOs, and every memcg - blkcg combination can be served by its own wb by assigning a dedicated wb to each memcg. This means that there may be multiple wb's of a bdi mapped to the same blkcg. As congested state is per blkcg - bdi combination, those wb's should share the same congested state. This is achieved by tracking congested state via bdi_writeback_congested structs which are keyed by blkcg. bdi->wb remains unchanged and will keep serving the root cgroup. cgwb's (cgroup wb's) for non-root cgroups are created on-demand or looked up while dirtying an inode according to the memcg of the page being dirtied or current task. Each cgwb is indexed on bdi->cgwb_tree by its memcg id. Once an inode is associated with its wb, it can be retrieved using inode_to_wb(). Currently, none of the filesystems has FS_CGROUP_WRITEBACK and all pages will keep being associated with bdi->wb. v3: inode_attach_wb() in account_page_dirtied() moved inside mapping_cap_account_dirty() block where it's known to be !NULL. Also, an unnecessary NULL check before kfree() removed. Both detected by the kbuild bot. v2: Updated so that wb association is per inode and wb is per memcg rather than blkcg. Signed-off-by: Tejun Heo <tj@kernel.org> Cc: kbuild test robot <fengguang.wu@intel.com> Cc: Dan Carpenter <dan.carpenter@oracle.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jan Kara <jack@suse.cz> Signed-off-by: Jens Axboe <axboe@fb.com>
2015-06-02blkcg: add blkcg_root_cssTejun Heo
Add global constant blkcg_root_css which points to &blkcg_root.css. This will be used by cgroup writeback support. If blkcg is disabled, it's defined as ERR_PTR(-EINVAL). v2: The declarations moved to include/linux/blk-cgroup.h as suggested by Vivek. Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Signed-off-by: Jens Axboe <axboe@fb.com>
2015-06-02blkcg: always create the blkcg_gq for the root blkcgTejun Heo
Currently, blkcg does a minor optimization where the root blkcg is created when the first blkcg policy is activated on a queue and destroyed on the deactivation of the last. On systems where blkcg is configured but not used, this saves one blkcg_gq struct per queue. On systems where blkcg is actually used, there's no difference. The only case where this can lead to any meaninful, albeit still minute, save in memory consumption is when all blkcg policies are deactivated after being widely used in the system, which is a hihgly unlikely scenario. The conditional existence of root blkcg_gq has already created several bugs in blkcg and became an issue once again for the new per-cgroup wb_congested mechanism for cgroup writeback support leading to a NULL dereference when no blkcg policy is active. This is really not worth bothering with. This patch makes blkcg always allocate and link the root blkcg_gq and release it only on queue destruction. Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2015-06-02blkcg: move block/blk-cgroup.h to include/linux/blk-cgroup.hTejun Heo
cgroup aware writeback support will require exposing some of blkcg details. In preprataion, move block/blk-cgroup.h to include/linux/blk-cgroup.h. This patch is pure file move. Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Vivek Goyal <vgoyal@redhat.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2014-09-08blkcg: remove blkcg->idTejun Heo
blkcg->id is a unique id given to each blkcg; however, the cgroup_subsys_state which each blkcg embeds already has ->serial_nr which can be used for the same purpose. Drop blkcg->id and replace its uses with blkcg->css.serial_nr. Rename cfq_cgroup->blkcg_id to ->blkcg_serial_nr and @id in check_blkcg_changed() to @serial_nr for consistency. Signed-off-by: Tejun Heo <tj@kernel.org> Acked-by: Vivek Goyal <vgoyal@redhat.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2014-08-04Merge branch 'for-3.17' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup Pull cgroup changes from Tejun Heo: "Mostly changes to get the v2 interface ready. The core features are mostly ready now and I think it's reasonable to expect to drop the devel mask in one or two devel cycles at least for a subset of controllers. - cgroup added a controller dependency mechanism so that block cgroup can depend on memory cgroup. This will be used to finally support IO provisioning on the writeback traffic, which is currently being implemented. - The v2 interface now uses a separate table so that the interface files for the new interface are explicitly declared in one place. Each controller will explicitly review and add the files for the new interface. - cpuset is getting ready for the hierarchical behavior which is in the similar style with other controllers so that an ancestor's configuration change doesn't change the descendants' configurations irreversibly and processes aren't silently migrated when a CPU or node goes down. All the changes are to the new interface and no behavior changed for the multiple hierarchies" * 'for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup: (29 commits) cpuset: fix the WARN_ON() in update_nodemasks_hier() cgroup: initialize cgrp_dfl_root_inhibit_ss_mask from !->dfl_files test cgroup: make CFTYPE_ONLY_ON_DFL and CFTYPE_NO_ internal to cgroup core cgroup: distinguish the default and legacy hierarchies when handling cftypes cgroup: replace cgroup_add_cftypes() with cgroup_add_legacy_cftypes() cgroup: rename cgroup_subsys->base_cftypes to ->legacy_cftypes cgroup: split cgroup_base_files[] into cgroup_{dfl|legacy}_base_files[] cpuset: export effective masks to userspace cpuset: allow writing offlined masks to cpuset.cpus/mems cpuset: enable onlined cpu/node in effective masks cpuset: refactor cpuset_hotplug_update_tasks() cpuset: make cs->{cpus, mems}_allowed as user-configured masks cpuset: apply cs->effective_{cpus,mems} cpuset: initialize top_cpuset's configured masks at mount cpuset: use effective cpumask to build sched domains cpuset: inherit ancestor's masks if effective_{cpus, mems} becomes empty cpuset: update cs->effective_{cpus, mems} when config changes cpuset: update cpuset->effective_{cpus,mems} at hotplug cpuset: add cs->effective_cpus and cs->effective_mems cgroup: clean up sane_behavior handling ...
2014-07-15cgroup: replace cgroup_add_cftypes() with cgroup_add_legacy_cftypes()Tejun Heo
Currently, cftypes added by cgroup_add_cftypes() are used for both the unified default hierarchy and legacy ones and subsystems can mark each file with either CFTYPE_ONLY_ON_DFL or CFTYPE_INSANE if it has to appear only on one of them. This is quite hairy and error-prone. Also, we may end up exposing interface files to the default hierarchy without thinking it through. cgroup_subsys will grow two separate cftype addition functions and apply each only on the hierarchies of the matching type. This will allow organizing cftypes in a lot clearer way and encourage subsystems to scrutinize the interface which is being exposed in the new default hierarchy. In preparation, this patch adds cgroup_add_legacy_cftypes() which currently is a simple wrapper around cgroup_add_cftypes() and replaces all cgroup_add_cftypes() usages with it. While at it, this patch drops a completely spurious return from __hugetlb_cgroup_file_init(). This patch doesn't introduce any functional differences. Signed-off-by: Tejun Heo <tj@kernel.org> Acked-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Li Zefan <lizefan@huawei.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Michal Hocko <mhocko@suse.cz> Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
2014-07-15cgroup: rename cgroup_subsys->base_cftypes to ->legacy_cftypesTejun Heo
Currently, cgroup_subsys->base_cftypes is used for both the unified default hierarchy and legacy ones and subsystems can mark each file with either CFTYPE_ONLY_ON_DFL or CFTYPE_INSANE if it has to appear only on one of them. This is quite hairy and error-prone. Also, we may end up exposing interface files to the default hierarchy without thinking it through. cgroup_subsys will grow two separate cftype arrays and apply each only on the hierarchies of the matching type. This will allow organizing cftypes in a lot clearer way and encourage subsystems to scrutinize the interface which is being exposed in the new default hierarchy. In preparation, this patch renames cgroup_subsys->base_cftypes to cgroup_subsys->legacy_cftypes. This patch is pure rename. Signed-off-by: Tejun Heo <tj@kernel.org> Acked-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Li Zefan <lizefan@huawei.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Michal Hocko <mhocko@suse.cz> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Paul Mackerras <paulus@samba.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Aristeu Rozanski <aris@redhat.com> Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
2014-07-12blkcg: don't call into policy draining if root_blkg is already goneTejun Heo
While a queue is being destroyed, all the blkgs are destroyed and its ->root_blkg pointer is set to NULL. If someone else starts to drain while the queue is in this state, the following oops happens. NULL pointer dereference at 0000000000000028 IP: [<ffffffff8144e944>] blk_throtl_drain+0x84/0x230 PGD e4a1067 PUD b773067 PMD 0 Oops: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC Modules linked in: cfq_iosched(-) [last unloaded: cfq_iosched] CPU: 1 PID: 537 Comm: bash Not tainted 3.16.0-rc3-work+ #2 Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 task: ffff88000e222250 ti: ffff88000efd4000 task.ti: ffff88000efd4000 RIP: 0010:[<ffffffff8144e944>] [<ffffffff8144e944>] blk_throtl_drain+0x84/0x230 RSP: 0018:ffff88000efd7bf0 EFLAGS: 00010046 RAX: 0000000000000000 RBX: ffff880015091450 RCX: 0000000000000001 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000 RBP: ffff88000efd7c10 R08: 0000000000000000 R09: 0000000000000001 R10: ffff88000e222250 R11: 0000000000000000 R12: ffff880015091450 R13: ffff880015092e00 R14: ffff880015091d70 R15: ffff88001508fc28 FS: 00007f1332650740(0000) GS:ffff88001fa80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b CR2: 0000000000000028 CR3: 0000000009446000 CR4: 00000000000006e0 Stack: ffffffff8144e8f6 ffff880015091450 0000000000000000 ffff880015091d80 ffff88000efd7c28 ffffffff8144ae2f ffff880015091450 ffff88000efd7c58 ffffffff81427641 ffff880015091450 ffffffff82401f00 ffff880015091450 Call Trace: [<ffffffff8144ae2f>] blkcg_drain_queue+0x1f/0x60 [<ffffffff81427641>] __blk_drain_queue+0x71/0x180 [<ffffffff81429b3e>] blk_queue_bypass_start+0x6e/0xb0 [<ffffffff814498b8>] blkcg_deactivate_policy+0x38/0x120 [<ffffffff8144ec44>] blk_throtl_exit+0x34/0x50 [<ffffffff8144aea5>] blkcg_exit_queue+0x35/0x40 [<ffffffff8142d476>] blk_release_queue+0x26/0xd0 [<ffffffff81454968>] kobject_cleanup+0x38/0x70 [<ffffffff81454848>] kobject_put+0x28/0x60 [<ffffffff81427505>] blk_put_queue+0x15/0x20 [<ffffffff817d07bb>] scsi_device_dev_release_usercontext+0x16b/0x1c0 [<ffffffff810bc339>] execute_in_process_context+0x89/0xa0 [<ffffffff817d064c>] scsi_device_dev_release+0x1c/0x20 [<ffffffff817930e2>] device_release+0x32/0xa0 [<ffffffff81454968>] kobject_cleanup+0x38/0x70 [<ffffffff81454848>] kobject_put+0x28/0x60 [<ffffffff817934d7>] put_device+0x17/0x20 [<ffffffff817d11b9>] __scsi_remove_device+0xa9/0xe0 [<ffffffff817d121b>] scsi_remove_device+0x2b/0x40 [<ffffffff817d1257>] sdev_store_delete+0x27/0x30 [<ffffffff81792ca8>] dev_attr_store+0x18/0x30 [<ffffffff8126f75e>] sysfs_kf_write+0x3e/0x50 [<ffffffff8126ea87>] kernfs_fop_write+0xe7/0x170 [<ffffffff811f5e9f>] vfs_write+0xaf/0x1d0 [<ffffffff811f69bd>] SyS_write+0x4d/0xc0 [<ffffffff81d24692>] system_call_fastpath+0x16/0x1b 776687bce42b ("block, blk-mq: draining can't be skipped even if bypass_depth was non-zero") made it easier to trigger this bug by making blk_queue_bypass_start() drain even when it loses the first bypass test to blk_cleanup_queue(); however, the bug has always been there even before the commit as blk_queue_bypass_start() could race against queue destruction, win the initial bypass test but perform the actual draining after blk_cleanup_queue() already destroyed all blkgs. Fix it by skippping calling into policy draining if all the blkgs are already gone. Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Shirish Pargaonkar <spargaonkar@suse.com> Reported-by: Sasha Levin <sasha.levin@oracle.com> Reported-by: Jet Chen <jet.chen@intel.com> Cc: stable@vger.kernel.org Tested-by: Shirish Pargaonkar <spargaonkar@suse.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2014-07-08blkcg, memcg: make blkcg depend on memcg on the default hierarchyTejun Heo
Currently, the blkio subsystem attributes all of writeback IOs to the root. One of the issues is that there's no way to tell who originated a writeback IO from block layer. Those IOs are usually issued asynchronously from a task which didn't have anything to do with actually generating the dirty pages. The memory subsystem, when enabled, already keeps track of the ownership of each dirty page and it's desirable for blkio to piggyback instead of adding its own per-page tag. cgroup now has a mechanism to express such dependency - cgroup_subsys->depends_on. This patch declares that blkcg depends on memcg so that memcg is enabled automatically on the default hierarchy when available. Future changes will make blkcg map the memcg tag to find out the cgroup to blame for writeback IOs. As this means that a memcg may be made invisible, this patch also implements css_reset() for memcg which resets its basic configurations. This implementation will probably need to be expanded to cover other states which are used in the default hierarchy. v2: blkcg's dependency on memcg is wrapped with CONFIG_MEMCG to avoid build failure. Reported by kbuild test robot. Signed-off-by: Tejun Heo <tj@kernel.org> Acked-by: Li Zefan <lizefan@huawei.com> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Cc: Michal Hocko <mhocko@suse.cz> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Jens Axboe <axboe@kernel.dk>