| Age | Commit message (Collapse) | Author |
|---|
|
Currently we acknowledge errors before clearing the error status.
This could cause a new error to be populated by firmware in-between
the error acknowledgment and the error status clearing which would
cause the second error's status to be cleared without being handled.
So, clear the error status before acknowledging the errors.
Also, make sure to acknowledge the error if the error status read
fails.
Signed-off-by: Tyler Baicar <tbaicar@codeaurora.org>
Reviewed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
According to the ACPI specification, firmware is not required to provide
the Hardware Error Source Table (HEST). When HEST is not present, the
following superfluous message is printed to the kernel boot log -
[ 3.460067] GHES: HEST is not enabled!
Extend hest_disable variable to track whether the firmware provides this
table and if it is not present skip any log output. The existing
behaviour is preserved in all other cases.
Suggested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ACPI defines a number of instructions to use for triggering errors. However
we are currently removing the address resources from the trigger resources
for only the WRITE_REGISTER_VALUE instruction. This leads to a resource
conflict for any other valid instruction.
Check that the instruction is less than or equal to the
WRITE_REGISTER_VALUE instruction. This allows all valid memory access
instructions and protects against invalid instructions.
Fixes: b4e008dc53a3 (ACPI, APEI, EINJ, Refine the fix of resource conflict)
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The revision 0x300 generic error data entry is different
from the old version, but currently iterating through the
GHES estatus blocks does not take into account this difference.
This will lead to failure to get the right data entry if GHES
has revision 0x300 error data entry.
Update the GHES estatus iteration macro to properly increment using
acpi_hest_get_next(), and correct the iteration termination condition
because the status block data length only includes error data
length.
Convert the CPER estatus checking and printing iteration logic
to use same macro.
Signed-off-by: Dongjiu Geng <gengdongjiu@huawei.com>
Tested-by: Tyler Baicar <tbaicar@codeaurora.org>
Reviewed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
X-Gene platforms describe multiple GHES error sources with the same
hardware error notification type (external interrupt) and interrupt
number.
Change the GHES interrupt request to support sharing the same IRQ.
This change includs contributions from Tuan Phan <tphan@apm.com>.
Signed-off-by: Loc Ho <lho@apm.com>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
- RAS reporting via GHES/APEI (ACPI)
- Indirect ftrace trampolines for modules
- Improvements to kernel fault reporting
- Page poisoning
- Sigframe cleanups and preparation for SVE context
- Core dump fixes
- Sparse fixes (mainly relating to endianness)
- xgene SoC PMU v3 driver
- Misc cleanups and non-critical fixes
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (75 commits)
arm64: fix endianness annotation for 'struct jit_ctx' and friends
arm64: cpuinfo: constify attribute_group structures.
arm64: ptrace: Fix incorrect get_user() use in compat_vfp_set()
arm64: ptrace: Remove redundant overrun check from compat_vfp_set()
arm64: ptrace: Avoid setting compat FP[SC]R to garbage if get_user fails
arm64: fix endianness annotation for __apply_alternatives()/get_alt_insn()
arm64: fix endianness annotation in get_kaslr_seed()
arm64: add missing conversion to __wsum in ip_fast_csum()
arm64: fix endianness annotation in acpi_parking_protocol.c
arm64: use readq() instead of readl() to read 64bit entry_point
arm64: fix endianness annotation for reloc_insn_movw() & reloc_insn_imm()
arm64: fix endianness annotation for aarch64_insn_write()
arm64: fix endianness annotation in aarch64_insn_read()
arm64: fix endianness annotation in call_undef_hook()
arm64: fix endianness annotation for debug-monitors.c
ras: mark stub functions as 'inline'
arm64: pass endianness info to sparse
arm64: ftrace: fix !CONFIG_ARM64_MODULE_PLTS kernels
arm64: signal: Allow expansion of the signal frame
acpi: apei: check for pending errors when probing GHES entries
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull RAS updates from Thomas Gleixner:
"The RAS updates for the 4.13 merge window:
- Cleanup of the MCE injection facility (Borsilav Petkov)
- Rework of the AMD/SMCA handling (Yazen Ghannam)
- Enhancements for ACPI/APEI to handle new notitication types (Shiju
Jose)
- atomic_t to refcount_t conversion (Elena Reshetova)
- A few fixes and enhancements all over the place"
* 'ras-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
RAS/CEC: Check the correct variable in the debugfs error handling
x86/mce: Always save severity in machine_check_poll()
x86/MCE, xen/mcelog: Make /dev/mcelog registration messages more precise
x86/mce: Update bootlog description to reflect behavior on AMD
x86/mce: Don't disable MCA banks when offlining a CPU on AMD
x86/mce/mce-inject: Preset the MCE injection struct
x86/mce: Clean up include files
x86/mce: Get rid of register_mce_write_callback()
x86/mce: Merge mce_amd_inj into mce-inject
x86/mce/AMD: Use saved threshold block info in interrupt handler
x86/mce/AMD: Use msr_stat when clearing MCA_STATUS
x86/mce/AMD: Carve out SMCA bank configuration
x86/mce/AMD: Redo error logging from APIC LVT interrupt handlers
x86/mce: Convert threshold_bank.cpus from atomic_t to refcount_t
RAS: Make local function parse_ras_param() static
ACPI/APEI: Handle GSIV and GPIO notification types
|
|
Check for pending errors when probing GHES entries. It is possible
that a fatal error is already pending at this point, so we should
handle it as soon as the driver is probed. This also avoids a
potential issue if there was an interrupt that was already
cleared for an error since the GHES driver wasn't present.
Signed-off-by: Tyler Baicar <tbaicar@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Currently external aborts are unsupported by the guest abort
handling. Add handling for SEAs so that the host kernel reports
SEAs which occur in the guest kernel.
When an SEA occurs in the guest kernel, the guest exits and is
routed to kvm_handle_guest_abort(). Prior to this patch, a print
message of an unsupported FSC would be printed and nothing else
would happen. With this patch, the code gets routed to the APEI
handling of SEAs in the host kernel to report the SEA information.
Signed-off-by: Tyler Baicar <tbaicar@codeaurora.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Currently there are trace events for the various RAS
errors with the exception of ARM processor type errors.
Add a new trace event for such errors so that the user
will know when they occur. These trace events are
consistent with the ARM processor error section type
defined in UEFI 2.6 spec section N.2.4.4.
Signed-off-by: Tyler Baicar <tbaicar@codeaurora.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Reviewed-by: Xie XiuQi <xiexiuqi@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
The UEFI spec includes non-standard section type support in the
Common Platform Error Record. This is defined in section N.2.3 of
UEFI version 2.5.
Currently if the CPER section's type (UUID) does not match any
section type that the kernel knows how to parse, a trace event is
not generated.
Generate a trace event which contains the raw error data for
non-standard section type error records.
Signed-off-by: Tyler Baicar <tbaicar@codeaurora.org>
CC: Jonathan (Zhixiong) Zhang <zjzhang@codeaurora.org>
Tested-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Even if an error status block's severity is fatal, the kernel does not
honor the severity level and panic.
With the firmware first model, the platform could inform the OS about a
fatal hardware error through the non-NMI GHES notification type. The OS
should panic when a hardware error record is received with this
severity.
Call panic() after CPER data in error status block is printed if
severity is fatal, before each error section is handled.
Signed-off-by: Jonathan (Zhixiong) Zhang <zjzhang@codeaurora.org>
Signed-off-by: Tyler Baicar <tbaicar@codeaurora.org>
Reviewed-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
ARM APEI extension proposal added SEA (Synchronous External Abort)
notification type for ARMv8.
Add a new GHES error source handling function for SEA. If an error
source's notification type is SEA, then this function can be registered
into the SEA exception handler. That way GHES will parse and report
SEA exceptions when they occur.
An SEA can interrupt code that had interrupts masked and is treated as
an NMI. To aid this the page of address space for mapping APEI buffers
while in_nmi() is always reserved, and ghes_ioremap_pfn_nmi() is
changed to use the helper methods to find the prot_t to map with in
the same way as ghes_ioremap_pfn_irq().
Signed-off-by: Tyler Baicar <tbaicar@codeaurora.org>
CC: Jonathan (Zhixiong) Zhang <zjzhang@codeaurora.org>
Reviewed-by: James Morse <james.morse@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
The ACPI 6.1 spec adds a new revision of the generic error data
entry structure. Add support to handle the new structure as well
as properly verify and iterate through the generic data entries.
Signed-off-by: Tyler Baicar <tbaicar@codeaurora.org>
CC: Jonathan (Zhixiong) Zhang <zjzhang@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
A RAS (Reliability, Availability, Serviceability) controller
may be a separate processor running in parallel with OS
execution, and may generate error records for consumption by
the OS. If the RAS controller produces multiple error records,
then they may be overwritten before the OS has consumed them.
The Generic Hardware Error Source (GHES) v2 structure
introduces the capability for the OS to acknowledge the
consumption of the error record generated by the RAS
controller. A RAS controller supporting GHESv2 shall wait for
the acknowledgment before writing a new error record, thus
eliminating the race condition.
Add support for parsing of GHESv2 sub-tables as well.
Signed-off-by: Tyler Baicar <tbaicar@codeaurora.org>
CC: Jonathan (Zhixiong) Zhang <zjzhang@codeaurora.org>
Reviewed-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
There are new types and helpers that are supposed to be used in new code.
As a preparation to get rid of legacy types and API functions do
the conversion here.
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
System Controller Interrupts are received by ACPI's error device, which
in turn notifies the GHES code. The same is true of APEI's GSIV and
GPIO notification types. Add support for GSIV and GPIO sharing the SCI
register/unregister/notifier code. Rename the list and notifier to show
this is no longer just SCI, but anything from the Hardware Error Device.
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
[ Rewrite commit log. ]
Signed-off-by: James Morse <james.morse@arm.com>
[ Some small cleanups ontop. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Tyler Baicar <tbaicar@codeaurora.org>
Reviewed-by: James Morse <james.morse@arm.com>
Link: http://lkml.kernel.org/r/86258A5CC0A3704780874CF6004BA8A62E695201@FRAEML521-MBX.china.huawei.com
Cc: "Guohanjun (Hanjun Guo)" <guohanjun@huawei.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: "Zhengqiang (turing)" <zhengqiang10@huawei.com>
Cc: "fu.wei@linaro.org" <fu.wei@linaro.org>
Cc: "xuwei (O)" <xuwei5@hisilicon.com>
Cc: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Cc: Geliang Tang <geliangtang@gmail.com>
Cc: John Garry <john.garry@huawei.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Punit Agrawal <punit.agrawal@arm.com>
Cc: linux-acpi@vger.kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
There are many code paths opencoding kvmalloc. Let's use the helper
instead. The main difference to kvmalloc is that those users are
usually not considering all the aspects of the memory allocator. E.g.
allocation requests <= 32kB (with 4kB pages) are basically never failing
and invoke OOM killer to satisfy the allocation. This sounds too
disruptive for something that has a reasonable fallback - the vmalloc.
On the other hand those requests might fallback to vmalloc even when the
memory allocator would succeed after several more reclaim/compaction
attempts previously. There is no guarantee something like that happens
though.
This patch converts many of those places to kv[mz]alloc* helpers because
they are more conservative.
Link: http://lkml.kernel.org/r/20170306103327.2766-2-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> # Xen bits
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Andreas Dilger <andreas.dilger@intel.com> # Lustre
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com> # KVM/s390
Acked-by: Dan Williams <dan.j.williams@intel.com> # nvdim
Acked-by: David Sterba <dsterba@suse.com> # btrfs
Acked-by: Ilya Dryomov <idryomov@gmail.com> # Ceph
Acked-by: Tariq Toukan <tariqt@mellanox.com> # mlx4
Acked-by: Leon Romanovsky <leonro@mellanox.com> # mlx5
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Anton Vorontsov <anton@enomsg.org>
Cc: Colin Cross <ccross@android.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Kent Overstreet <kent.overstreet@gmail.com>
Cc: Santosh Raspatur <santosh@chelsio.com>
Cc: Hariprasad S <hariprasad@chelsio.com>
Cc: Yishai Hadas <yishaih@mellanox.com>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: "Yan, Zheng" <zyan@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull pstore updates from Kees Cook:
"This has a large internal refactoring along with several smaller
fixes.
- constify compression structures; Bhumika Goyal
- restore powerpc dumping; Ankit Kumar
- fix more bugs in the rarely exercises module unloading logic
- reorganize filesystem locking to fix problems noticed by lockdep
- refactor internal pstore APIs to make development and review
easier:
- improve error reporting
- add kernel-doc structure and function comments
- avoid insane argument passing by using a common record
structure"
* tag 'pstore-v4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (23 commits)
pstore: Solve lockdep warning by moving inode locks
pstore: Fix flags to enable dumps on powerpc
pstore: Remove unused vmalloc.h in pmsg
pstore: simplify write_user_compat()
pstore: Remove write_buf() callback
pstore: Replace arguments for write_buf_user() API
pstore: Replace arguments for write_buf() API
pstore: Replace arguments for erase() API
pstore: Do not duplicate record metadata
pstore: Allocate records on heap instead of stack
pstore: Pass record contents instead of copying
pstore: Always allocate buffer for decompression
pstore: Replace arguments for write() API
pstore: Replace arguments for read() API
pstore: Switch pstore_mkfile to pass record
pstore: Move record decompression to function
pstore: Extract common arguments into structure
pstore: Add kernel-doc for struct pstore_info
pstore: Improve register_pstore() error reporting
pstore: Avoid race in module unloading
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull RAS updates from Ingo Molnar:
"The main changes in this cycle were:
- add the 'Corrected Errors Collector' kernel feature which collect
and monitor correctable errors statistics and will preemptively
(soft-)offline physical pages that have a suspiciously high error
count.
- handle MCE errors during kexec() more gracefully
- factor out and deprecate the /dev/mcelog driver
- ... plus misc fixes and cleanpus"
* 'ras-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mce: Check MCi_STATUS[MISCV] for usable addr on Intel only
ACPI/APEI: Use setup_deferrable_timer()
x86/mce: Update notifier priority check
x86/mce: Enable PPIN for Knights Landing/Mill
x86/mce: Do not register notifiers with invalid prio
x86/mce: Factor out and deprecate the /dev/mcelog driver
RAS: Add a Corrected Errors Collector
x86/mce: Rename mce_log to mce_log_buffer
x86/mce: Rename mce_log()'s argument
x86/mce: Init some CPU features early
x86/mce: Handle broadcasted MCE gracefully with kexec
|
|
Use setup_deferrable_timer() instead of init_timer_deferrable() to
simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Tested-by: Tyler Baicar <tbaicar@codeaurora.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Len Brown <lenb@kernel.org>
Cc: linux-acpi@vger.kernel.org
Link: http://lkml.kernel.org/r/3afa5498142ef68256023257dad37b9f8352e65e.1489060803.git.geliangtang@gmail.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
When removing a GHES device notified by SCI, list_del_rcu() is used,
ghes_remove() should call synchronize_rcu() before it goes on to call
kfree(ghes), otherwise concurrent RCU readers may still hold this list
entry after it has been freed.
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: "Huang, Ying" <ying.huang@intel.com>
Fixes: 81e88fdc432a (ACPI, APEI, Generic Hardware Error Source POLL/IRQ/NMI notification type support)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This removes the argument list for the erase() callback and replaces it
with a pointer to the backend record details to be removed.
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
Similar to the pstore_info read() callback, there were too many arguments.
This switches to the new struct pstore_record pointer instead. This adds
"reason" and "part" to the record structure as well.
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
The argument list for the pstore_read() interface is unwieldy. This changes
passes the new struct pstore_record instead. The erst backend was already
doing something similar internally.
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull sched.h split-up from Ingo Molnar:
"The point of these changes is to significantly reduce the
<linux/sched.h> header footprint, to speed up the kernel build and to
have a cleaner header structure.
After these changes the new <linux/sched.h>'s typical preprocessed
size goes down from a previous ~0.68 MB (~22K lines) to ~0.45 MB (~15K
lines), which is around 40% faster to build on typical configs.
Not much changed from the last version (-v2) posted three weeks ago: I
eliminated quirks, backmerged fixes plus I rebased it to an upstream
SHA1 from yesterday that includes most changes queued up in -next plus
all sched.h changes that were pending from Andrew.
I've re-tested the series both on x86 and on cross-arch defconfigs,
and did a bisectability test at a number of random points.
I tried to test as many build configurations as possible, but some
build breakage is probably still left - but it should be mostly
limited to architectures that have no cross-compiler binaries
available on kernel.org, and non-default configurations"
* 'WIP.sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (146 commits)
sched/headers: Clean up <linux/sched.h>
sched/headers: Remove #ifdefs from <linux/sched.h>
sched/headers: Remove the <linux/topology.h> include from <linux/sched.h>
sched/headers, hrtimer: Remove the <linux/wait.h> include from <linux/hrtimer.h>
sched/headers, x86/apic: Remove the <linux/pm.h> header inclusion from <asm/apic.h>
sched/headers, timers: Remove the <linux/sysctl.h> include from <linux/timer.h>
sched/headers: Remove <linux/magic.h> from <linux/sched/task_stack.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/init.h>
sched/core: Remove unused prefetch_stack()
sched/headers: Remove <linux/rculist.h> from <linux/sched.h>
sched/headers: Remove the 'init_pid_ns' prototype from <linux/sched.h>
sched/headers: Remove <linux/signal.h> from <linux/sched.h>
sched/headers: Remove <linux/rwsem.h> from <linux/sched.h>
sched/headers: Remove the runqueue_is_locked() prototype
sched/headers: Remove <linux/sched.h> from <linux/sched/hotplug.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/debug.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/nohz.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/stat.h>
sched/headers: Remove the <linux/gfp.h> include from <linux/sched.h>
sched/headers: Remove <linux/rtmutex.h> from <linux/sched.h>
...
|
|
<linux/sched/clock.h>
We are going to split <linux/sched/clock.h> out of <linux/sched.h>, which
will have to be picked up from other headers and .c files.
Create a trivial placeholder <linux/sched/clock.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
It was reported that on some machines, there is overlap between ACPI
NVS area and BERT address range. This appears reasonable because BERT
contents need to be non-volatile across reboot. But this will cause
resources conflict in current Linux kernel implementation because the
ACPI NVS area is marked as busy. The resource conflict is fixed via
excluding the ACPI NVS area when requesting IO resources for BERT.
When accessing the BERT contents, the whole BERT address range will be
ioremapped and accessed.
Reported-and-tested-by: Hans Kristian Rosbach <hansr@raskesider.no>
Signed-off-by: Ying Huang <ying.huang@intel.com>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The pr_warn message has a malformed newline escape, add in the
missing \
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This patch provides APEI arch-specific bits for ARM64
Meanwhile,
(1) Move HEST type (ACPI_HEST_TYPE_IA32_CORRECTED_CHECK) checking to
a generic place.
(2) Select HAVE_ACPI_APEI when EFI and ACPI is set on ARM64, because
arch_apei_get_mem_attribute is using efi_mem_attributes() on
ARM64.
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Tested-by: Jonathan (Zhixiong) Zhang <zjzhang@codeaurora.org>
Signed-off-by: Fu Wei <fu.wei@linaro.org>
[ Fu Wei: improve && upstream ]
Acked-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Tyler Baicar <tbaicar@codeaurora.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When removing and adding cpu 0 on a system with GHES NMI the following stack
trace is seen when re-adding the cpu:
WARNING: CPU: 0 PID: 0 at arch/x86/kernel/apic/apic.c:1349 setup_local_APIC+
Modules linked in: nfsv3 rpcsec_gss_krb5 nfsv4 nfs fscache coretemp intel_ra
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.9.0-rc6+ #2
Call Trace:
dump_stack+0x63/0x8e
__warn+0xd1/0xf0
warn_slowpath_null+0x1d/0x20
setup_local_APIC+0x275/0x370
apic_ap_setup+0xe/0x20
start_secondary+0x48/0x180
set_init_arg+0x55/0x55
early_idt_handler_array+0x120/0x120
x86_64_start_reservations+0x2a/0x2c
x86_64_start_kernel+0x13d/0x14c
During the cpu bringup, wakeup_cpu_via_init_nmi() is called and issues an
NMI on CPU 0. The GHES NMI handler, ghes_notify_nmi() runs the
ghes_proc_irq_work work queue which ends up setting IRQ_WORK_VECTOR
(0xf6). The "faulty" IR line set at arch/x86/kernel/apic/apic.c:1349 is also
0xf6 (specifically APIC IRR for irqs 255 to 224 is 0x400000) which confirms
that something has set the IRQ_WORK_VECTOR line prior to the APIC being
initialized.
Commit 2383844d4850 ("GHES: Elliminate double-loop in the NMI handler")
incorrectly modified the behavior such that the handler returns
NMI_HANDLED only if an error was processed, and incorrectly runs the ghes
work queue for every NMI.
This patch modifies the ghes_proc_irq_work() to run as it did prior to
2383844d4850 ("GHES: Elliminate double-loop in the NMI handler") by
properly returning NMI_HANDLED and only calling the work queue if
NMI_HANDLED has been set.
Fixes: 2383844d4850 (GHES: Elliminate double-loop in the NMI handler)
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Although ghes_proc() tests for errors while reading the error status,
it always return success (0). Fix this by propagating the return
value.
Fixes: d334a49113a4a33 (ACPI, APEI, Generic Hardware Error Source memory error support)
Signed-of-by: Punit Agrawal <punit.agrawa.@arm.com>
Tested-by: Tyler Baicar <tbaicar@codeaurora.org>
Reviewed-by: Borislav Petkov <bp@suse.de>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Summary of PCI changes for the v4.9 merge window:
Enumeration:
- microblaze: Add multidomain support for procfs (Bharat Kumar Gogada)
Resource management:
- Ignore requested alignment for PROBE_ONLY and fixed resources (Yongji Xie)
- Ignore requested alignment for VF BARs (Yongji Xie)
PCI device hotplug:
- Make core explicitly non-modular (Paul Gortmaker)
PCIe native device hotplug:
- Rename pcie_isr() locals for clarity (Bjorn Helgaas)
- Return IRQ_NONE when we can't read interrupt status (Bjorn Helgaas)
- Remove unnecessary guard (Bjorn Helgaas)
- Clean up dmesg "Slot(%s)" messages (Bjorn Helgaas)
- Remove useless pciehp_get_latch_status() calls (Bjorn Helgaas)
- Clear attention LED on device add (Keith Busch)
- Allow exclusive userspace control of indicators (Keith Busch)
- Process all hotplug events before looking for new ones (Mayurkumar Patel)
- Don't re-read Slot Status when queuing hotplug event (Mayurkumar Patel)
- Don't re-read Slot Status when handling surprise event (Mayurkumar Patel)
- Make explicitly non-modular (Paul Gortmaker)
Power management:
- Afford direct-complete to devices with non-standard PM (Lukas Wunner)
- Query platform firmware for device power state (Lukas Wunner)
- Recognize D3cold in pci_update_current_state() (Lukas Wunner)
- Avoid unnecessary resume after direct-complete (Lukas Wunner)
- Make explicitly non-modular (Paul Gortmaker)
Virtualization:
- Mark Atheros AR9580 to avoid bus reset (Maik Broemme)
- Check for pci_setup_device() failure in pci_iov_add_virtfn() (Po Liu)
MSI:
- Enable PCI_MSI_IRQ_DOMAIN support for ARC (Joao Pinto)
AER:
- Remove aerdriver.nosourceid kernel parameter (Bjorn Helgaas)
- Remove aerdriver.forceload kernel parameter (Bjorn Helgaas)
- Fix aer_probe() kernel-doc comment (Cao jin)
- Add bus flag to skip source ID matching (Jon Derrick)
- Avoid memory allocation in interrupt handling path (Jon Derrick)
- Cache capability position (Keith Busch)
- Make explicitly non-modular (Paul Gortmaker)
- Remove duplicate AER severity translation (Tyler Baicar)
- Send correct severity to calculate AER severity (Tyler Baicar)
Precision Time Measurement:
- Add Precision Time Measurement (PTM) support (Jonathan Yong)
- Add PTM clock granularity information (Bjorn Helgaas)
- Add pci_enable_ptm() for drivers to enable PTM on endpoints (Bjorn Helgaas)
Generic host bridge driver:
- Fix pci_remap_iospace() failure path (Lorenzo Pieralisi)
- Make explicitly non-modular (Paul Gortmaker)
Altera host bridge driver:
- Remove redundant platform_get_resource() return value check (Bjorn Helgaas)
- Poll for link training status after retraining the link (Ley Foon Tan)
- Rework config accessors for use without a struct pci_bus (Ley Foon Tan)
- Move retrain from fixup to altera_pcie_host_init() (Ley Foon Tan)
- Make MSI explicitly non-modular (Paul Gortmaker)
- Make explicitly non-modular (Paul Gortmaker)
- Relax device number checking to allow SR-IOV (Po Liu)
ARM Versatile host bridge driver:
- Fix pci_remap_iospace() failure path (Lorenzo Pieralisi)
Axis ARTPEC-6 host bridge driver:
- Drop __init from artpec6_add_pcie_port() (Niklas Cassel)
Freescale i.MX6 host bridge driver:
- Make explicitly non-modular (Paul Gortmaker)
Intel VMD host bridge driver:
- Add quirk for AER to ignore source ID (Jon Derrick)
- Allocate IRQ lists with correct MSI-X count (Jon Derrick)
- Convert to use pci_alloc_irq_vectors() API (Jon Derrick)
- Eliminate vmd_vector member from list type (Jon Derrick)
- Eliminate index member from IRQ list (Jon Derrick)
- Synchronize with RCU freeing MSI IRQ descs (Keith Busch)
- Request userspace control of PCIe hotplug indicators (Keith Busch)
- Move VMD driver to drivers/pci/host (Keith Busch)
Marvell Aardvark host bridge driver:
- Fix pci_remap_iospace() failure path (Lorenzo Pieralisi)
- Remove redundant dev_err call in advk_pcie_probe() (Wei Yongjun)
Microsoft Hyper-V host bridge driver:
- Use zero-length array in struct pci_packet (Dexuan Cui)
- Use pci_function_description[0] in struct definitions (Dexuan Cui)
- Remove the unused 'wrk' in struct hv_pcibus_device (Dexuan Cui)
- Handle vmbus_sendpacket() failure in hv_compose_msi_msg() (Dexuan Cui)
- Handle hv_pci_generic_compl() error case (Dexuan Cui)
- Use list_move_tail() instead of list_del() + list_add_tail() (Wei Yongjun)
NVIDIA Tegra host bridge driver:
- Fix pci_remap_iospace() failure path (Lorenzo Pieralisi)
- Remove redundant _data suffix (Thierry Reding)
- Use of_device_get_match_data() (Thierry Reding)
Qualcomm host bridge driver:
- Make explicitly non-modular (Paul Gortmaker)
Renesas R-Car host bridge driver:
- Consolidate register space lookup and ioremap (Bjorn Helgaas)
- Don't disable/unprepare clocks on prepare/enable failure (Geert Uytterhoeven)
- Add multi-MSI support (Grigory Kletsko)
- Fix pci_remap_iospace() failure path (Lorenzo Pieralisi)
- Fix some checkpatch warnings (Sergei Shtylyov)
- Try increasing PCIe link speed to 5 GT/s at boot (Sergei Shtylyov)
Rockchip host bridge driver:
- Add DT bindings for Rockchip PCIe controller (Shawn Lin)
- Add Rockchip PCIe controller support (Shawn Lin)
- Improve the deassert sequence of four reset pins (Shawn Lin)
- Fix wrong transmitted FTS count (Shawn Lin)
- Increase the Max Credit update interval (Rajat Jain)
Samsung Exynos host bridge driver:
- Make explicitly non-modular (Paul Gortmaker)
ST Microelectronics SPEAr13xx host bridge driver:
- Make explicitly non-modular (Paul Gortmaker)
Synopsys DesignWare host bridge driver:
- Return data directly from dw_pcie_readl_rc() (Bjorn Helgaas)
- Exchange viewport of `MEMORYs' and `CFGs/IOs' (Dong Bo)
- Check LTSSM training bit before deciding link is up (Jisheng Zhang)
- Move link wait definitions to .c file (Joao Pinto)
- Wait for iATU enable (Joao Pinto)
- Add iATU Unroll feature (Joao Pinto)
- Fix pci_remap_iospace() failure path (Lorenzo Pieralisi)
- Make explicitly non-modular (Paul Gortmaker)
- Relax device number checking to allow SR-IOV (Po Liu)
- Keep viewport fixed for IO transaction if num_viewport > 2 (Pratyush Anand)
- Remove redundant platform_get_resource() return value check (Wei Yongjun)
TI DRA7xx host bridge driver:
- Make explicitly non-modular (Paul Gortmaker)
TI Keystone host bridge driver:
- Propagate request_irq() failure (Wei Yongjun)
Xilinx AXI host bridge driver:
- Keep both legacy and MSI interrupt domain references (Bharat Kumar Gogada)
- Clear interrupt register for invalid interrupt (Bharat Kumar Gogada)
- Clear correct MSI set bit (Bharat Kumar Gogada)
- Dispose of MSI virtual IRQ (Bharat Kumar Gogada)
- Make explicitly non-modular (Paul Gortmaker)
- Relax device number checking to allow SR-IOV (Po Liu)
Xilinx NWL host bridge driver:
- Expand error logging (Bharat Kumar Gogada)
- Enable all MSI interrupts using MSI mask (Bharat Kumar Gogada)
- Make explicitly non-modular (Paul Gortmaker)
Miscellaneous:
- Drop CONFIG_KEXEC_CORE ifdeffery (Lukas Wunner)
- portdrv: Make explicitly non-modular (Paul Gortmaker)
- Make DPC explicitly non-modular (Paul Gortmaker)"
* tag 'pci-v4.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (105 commits)
x86/PCI: VMD: Move VMD driver to drivers/pci/host
PCI: rockchip: Fix wrong transmitted FTS count
PCI: rockchip: Improve the deassert sequence of four reset pins
PCI: rockchip: Increase the Max Credit update interval
PCI: rcar: Try increasing PCIe link speed to 5 GT/s at boot
PCI/AER: Fix aer_probe() kernel-doc comment
PCI: Ignore requested alignment for VF BARs
PCI: Ignore requested alignment for PROBE_ONLY and fixed resources
PCI: Avoid unnecessary resume after direct-complete
PCI: Recognize D3cold in pci_update_current_state()
PCI: Query platform firmware for device power state
PCI: Afford direct-complete to devices with non-standard PM
PCI/AER: Cache capability position
PCI/AER: Avoid memory allocation in interrupt handling path
x86/PCI: VMD: Request userspace control of PCIe hotplug indicators
PCI: pciehp: Allow exclusive userspace control of indicators
ACPI / APEI: Send correct severity to calculate AER severity
PCI/AER: Remove duplicate AER severity translation
x86/PCI: VMD: Synchronize with RCU freeing MSI IRQ descs
x86/PCI: VMD: Eliminate index member from IRQ list
...
|
|
Currently the AER severity is calculated by calling cper_severity_to_aer(),
but the parameter sent is actually the GHES severity. This causes the AER
severity to be incorrect.
Fix the parameter to be the CPER severity instead of the GHES severity.
Signed-off-by: Tyler Baicar <tbaicar@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
|
|
This patch adds new PSTORE_FLAGS for each pstore type so that they can
be enabled separately. This is a preparation for ongoing virtio-pstore
work to support those types flexibly.
The PSTORE_FLAGS_FRAGILE is changed to PSTORE_FLAGS_DMESG to preserve the
original behavior.
Cc: Anton Vorontsov <anton@enomsg.org>
Cc: Colin Cross <ccross@android.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: linux-acpi@vger.kernel.org
Cc: linux-efi@vger.kernel.org
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
[kees: retained "FRAGILE" for now to make merges easier]
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull pstore subsystem updates from Kees Cook:
"This expands the supported compressors, fixes some bugs, and finally
adds DT bindings"
* tag 'pstore-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
pstore/ram: add Device Tree bindings
efi-pstore: implement efivars_pstore_exit()
pstore: drop file opened reference count
pstore: add lzo/lz4 compression support
pstore: Cleanup pstore_dump()
pstore: Enable compression on normal path (again)
ramoops: Only unregister when registered
|
|
ACPI/APEI is designed to verifiy/report H/W errors, like Corrected
Error(CE) and Uncorrected Error(UC). It contains four tables: HEST,
ERST, EINJ and BERT. The first three tables have been merged for
a long time, but because of lacking BIOS support for BERT, the
support for BERT is pending until now. Recently on ARM 64 platform
it is has been supported. So here we come.
Under normal circumstances, when a hardware error occurs, kernel will
be notified via NMI, MCE or some other method, then kernel will
process the error condition, report it, and recover it if possible.
But sometime, the situation is so bad, so that firmware may choose to
reset directly without notifying Linux kernel.
Linux kernel can use the Boot Error Record Table (BERT) to get the
un-notified hardware errors that occurred in a previous boot. In this
patch, the error information is reported via printk.
For more information about BERT, please refer to ACPI Specification
version 6.0, section 18.3.1:
http://www.uefi.org/sites/default/files/resources/ACPI_6.0.pdf
The following log is a BERT record after system reboot because of hitting
a fatal memory error:
BERT: Error records from previous boot:
[Hardware Error]: It has been corrected by h/w and requires no further action
[Hardware Error]: event severity: corrected
[Hardware Error]: Error 0, type: recoverable
[Hardware Error]: section_type: memory error
[Hardware Error]: error_status: 0x0000000000000400
[Hardware Error]: physical_address: 0xffffffffffffffff
[Hardware Error]: card: 1 module: 2 bank: 3 row: 1 column: 2 bit_position: 5
[Hardware Error]: error_type: 2, single-bit ECC
[Tomasz Nowicki: Clear error status at the end of error handling]
[Tony: Applied some cleanups suggested by Fu Wei]
[Fu Wei: delete EXPORT_SYMBOL_GPL(bert_disable), improve the code]
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Signed-off-by: Chen, Gong <gong.chen@linux.intel.com>
Tested-by: Jonathan (Zhixiong) Zhang <zjzhang@codeaurora.org>
Signed-off-by: Fu Wei <fu.wei@linaro.org>
Tested-by: Tyler Baicar <tbaicar@codeaurora.org>
Reviewed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
It is absolutely unfriendly when one sees this:
# modprobe einj
modprobe: ERROR: could not insert 'einj': No such device
without anything in dmesg to tell one why the load failed.
Beef up the error handling of the init function to be more user-friendly
when the load fails.
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
... and remove it from the pr_* calls.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Like zlib compression in pstore, this patch added lzo and lz4
compression support so that users can have more options and better
compression ratio.
The original code treats the compressed data together with the
uncompressed ECC correction notice by using zlib decompress. The
ECC correction notice is missing in the decompression process. The
treatment also makes lzo and lz4 not working. So I treat them
separately by using pstore_decompress() to treat the compressed
data, and memcpy() to treat the uncompressed ECC correction notice.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"This time the majority of changes go into cpufreq and they are
significant.
First off, the way CPU frequency updates are triggered is different
now. Instead of having to set up and manage a deferrable timer for
each CPU in the system to evaluate and possibly change its frequency
periodically, cpufreq governors set up callbacks to be invoked by the
scheduler on a regular basis (basically on utilization updates). The
"old" governors, "ondemand" and "conservative", still do all of their
work in process context (although that is triggered by the scheduler
now), but intel_pstate does it all in the callback invoked by the
scheduler with no need for any additional asynchronous processing.
Of course, this eliminates the overhead related to the management of
all those timers, but also it allows the cpufreq governor code to be
simplified quite a bit. On top of that, the common code and data
structures used by the "ondemand" and "conservative" governors are
cleaned up and made more straightforward and some long-standing and
quite annoying problems are addressed. In particular, the handling of
governor sysfs attributes is modified and the related locking becomes
more fine grained which allows some concurrency problems to be avoided
(particularly deadlocks with the core cpufreq code).
In principle, the new mechanism for triggering frequency updates
allows utilization information to be passed from the scheduler to
cpufreq. Although the current code doesn't make use of it, in the
works is a new cpufreq governor that will make decisions based on the
scheduler's utilization data. That should allow the scheduler and
cpufreq to work more closely together in the long run.
In addition to the core and governor changes, cpufreq drivers are
updated too. Fixes and optimizations go into intel_pstate, the
cpufreq-dt driver is updated on top of some modification in the
Operating Performance Points (OPP) framework and there are fixes and
other updates in the powernv cpufreq driver.
Apart from the cpufreq updates there is some new ACPICA material,
including a fix for a problem introduced by previous ACPICA updates,
and some less significant changes in the ACPI code, like CPPC code
optimizations, ACPI processor driver cleanups and support for loading
ACPI tables from initrd.
Also updated are the generic power domains framework, the Intel RAPL
power capping driver and the turbostat utility and we have a bunch of
traditional assorted fixes and cleanups.
Specifics:
- Redesign of cpufreq governors and the intel_pstate driver to make
them use callbacks invoked by the scheduler to trigger CPU
frequency evaluation instead of using per-CPU deferrable timers for
that purpose (Rafael Wysocki).
- Reorganization and cleanup of cpufreq governor code to make it more
straightforward and fix some concurrency problems in it (Rafael
Wysocki, Viresh Kumar).
- Cleanup and improvements of locking in the cpufreq core (Viresh
Kumar).
- Assorted cleanups in the cpufreq core (Rafael Wysocki, Viresh
Kumar, Eric Biggers).
- intel_pstate driver updates including fixes, optimizations and a
modification to make it enable enable hardware-coordinated P-state
selection (HWP) by default if supported by the processor (Philippe
Longepe, Srinivas Pandruvada, Rafael Wysocki, Viresh Kumar, Felipe
Franciosi).
- Operating Performance Points (OPP) framework updates to improve its
handling of voltage regulators and device clocks and updates of the
cpufreq-dt driver on top of that (Viresh Kumar, Jon Hunter).
- Updates of the powernv cpufreq driver to fix initialization and
cleanup problems in it and correct its worker thread handling with
respect to CPU offline, new powernv_throttle tracepoint (Shilpasri
Bhat).
- ACPI cpufreq driver optimization and cleanup (Rafael Wysocki).
- ACPICA updates including one fix for a regression introduced by
previos changes in the ACPICA code (Bob Moore, Lv Zheng, David Box,
Colin Ian King).
- Support for installing ACPI tables from initrd (Lv Zheng).
- Optimizations of the ACPI CPPC code (Prashanth Prakash, Ashwin
Chaugule).
- Support for _HID(ACPI0010) devices (ACPI processor containers) and
ACPI processor driver cleanups (Sudeep Holla).
- Support for ACPI-based enumeration of the AMBA bus (Graeme Gregory,
Aleksey Makarov).
- Modification of the ACPI PCI IRQ management code to make it treat
255 in the Interrupt Line register as "not connected" on x86 (as
per the specification) and avoid attempts to use that value as a
valid interrupt vector (Chen Fan).
- ACPI APEI fixes related to resource leaks (Josh Hunt).
- Removal of modularity from a few ACPI drivers (BGRT, GHES,
intel_pmic_crc) that cannot be built as modules in practice (Paul
Gortmaker).
- PNP framework update to make it treat ACPI_RESOURCE_TYPE_SERIAL_BUS
as a valid resource type (Harb Abdulhamid).
- New device ID (future AMD I2C controller) in the ACPI driver for
AMD SoCs (APD) and in the designware I2C driver (Xiangliang Yu).
- Assorted ACPI cleanups (Colin Ian King, Kaiyen Chang, Oleg Drokin).
- cpuidle menu governor optimization to avoid a square root
computation in it (Rasmus Villemoes).
- Fix for potential use-after-free in the generic device properties
framework (Heikki Krogerus).
- Updates of the generic power domains (genpd) framework including
support for multiple power states of a domain, fixes and debugfs
output improvements (Axel Haslam, Jon Hunter, Laurent Pinchart,
Geert Uytterhoeven).
- Intel RAPL power capping driver updates to reduce IPI overhead in
it (Jacob Pan).
- System suspend/hibernation code cleanups (Eric Biggers, Saurabh
Sengar).
- Year 2038 fix for the process freezer (Abhilash Jindal).
- turbostat utility updates including new features (decoding of more
registers and CPUID fields, sub-second intervals support, GFX MHz
and RC6 printout, --out command line option), fixes (syscall jitter
detection and workaround, reductioin of the number of syscalls
made, fixes related to Xeon x200 processors, compiler warning
fixes) and cleanups (Len Brown, Hubert Chrzaniuk, Chen Yu)"
* tag 'pm+acpi-4.6-rc1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (182 commits)
tools/power turbostat: bugfix: TDP MSRs print bits fixing
tools/power turbostat: correct output for MSR_NHM_SNB_PKG_CST_CFG_CTL dump
tools/power turbostat: call __cpuid() instead of __get_cpuid()
tools/power turbostat: indicate SMX and SGX support
tools/power turbostat: detect and work around syscall jitter
tools/power turbostat: show GFX%rc6
tools/power turbostat: show GFXMHz
tools/power turbostat: show IRQs per CPU
tools/power turbostat: make fewer systems calls
tools/power turbostat: fix compiler warnings
tools/power turbostat: add --out option for saving output in a file
tools/power turbostat: re-name "%Busy" field to "Busy%"
tools/power turbostat: Intel Xeon x200: fix turbo-ratio decoding
tools/power turbostat: Intel Xeon x200: fix erroneous bclk value
tools/power turbostat: allow sub-sec intervals
ACPI / APEI: ERST: Fixed leaked resources in erst_init
ACPI / APEI: Fix leaked resources
intel_pstate: Do not skip samples partially
intel_pstate: Remove freq calculation from intel_pstate_calc_busy()
intel_pstate: Move intel_pstate_calc_busy() into get_target_pstate_use_performance()
...
|
|
* acpi-ec:
ACPI / EC: Deny write access unless requested by module param
* acpi-fan:
ACPI / fan: Make struct dev_pm_ops const
* acpi-video:
ACPI / video: remove unused device_decode array
* acpi-misc:
ACPI / util: remove redundant check if element is NULL
ACPI: Add acpi_force_32bit_fadt_addr option to force 32 bit FADT addresses
drivers/acpi: make pmic/intel_pmic_crc.c explicitly non-modular
drivers/acpi: make apei/ghes.c more explicitly non-modular
drivers/acpi: make bgrt driver explicitly non-modular
|
|
erst_init currently leaks resources allocated from its call to
apei_resources_init(). The data allocated there gets copied
into apei_resources_all and can be freed when we're done with it.
Signed-off-by: Josh Hunt <johunt@akamai.com>
Reviewed-by: Chen, Gong <gong.chen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
We leak the NVS and arch resources (if used), in apei_resources_request.
They are allocated to make sure we exclude them from the APEI resources,
but they are never freed at the end of the function. Free them now.
Signed-off-by: Josh Hunt <johunt@akamai.com>
Reviewed-by: Chen, Gong <gong.chen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The Kconfig currently controlling compilation of this code is:
config ACPI_APEI_GHES
bool "APEI Generic Hardware Error Source"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We replace module.h with moduleparam.h as we are keeping the
pre-existing module_param that the file has, as currently that is
the easiest way to maintain compatibility with the existing boot
arg use cases.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In the case of memory error injection, einj_error_inject()
checks if a target address is System RAM. Change this check to
allow injecting a memory error into NVDIMM memory by calling
region_intersects() with IORES_DESC_PERSISTENT_MEMORY. This
enables memory error testing on both System RAM and NVDIMM.
In addition, page_is_ram() is replaced with region_intersects()
with IORESOURCE_SYSTEM_RAM, so that it can verify a target
address range with the requested size.
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luis R. Rodriguez <mcgrof@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: linux-acpi@vger.kernel.org
Cc: linux-arch@vger.kernel.org
Cc: linux-mm <linux-mm@kvack.org>
Cc: linux-nvdimm@lists.01.org
Link: http://lkml.kernel.org/r/1453841853-11383-18-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
There are many locations that do
if (memory_was_allocated_by_vmalloc)
vfree(ptr);
else
kfree(ptr);
but kvfree() can handle both kmalloc()ed memory and vmalloc()ed memory
using is_vmalloc_addr(). Unless callers have special reasons, we can
replace this branch with kvfree(). Please check and reply if you found
problems.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Jan Kara <jack@suse.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Acked-by: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Acked-by: David Rientjes <rientjes@google.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: Boris Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
If the ACPI APEI firmware handles hardware error first (called
"firmware first handling"), the firmware updates the GHES memory
region with hardware error record (called "generic hardware
error record"). Essentially the firmware writes hardware error
records in the GHES memory region, triggers an NMI/interrupt,
then the GHES driver goes off and grabs the error record from
the GHES region.
The kernel currently maps the GHES memory region as cacheable
(PAGE_KERNEL) for all architectures. However, on some arm64
platforms, there is a mismatch between how the kernel maps the
GHES region (PAGE_KERNEL) and how the firmware maps it
(EFI_MEMORY_UC, ie. uncacheable), leading to the possibility of
the kernel GHES driver reading stale data from the cache when it
receives the interrupt.
With stale data being read, the kernel is unaware there is new
hardware error to be handled when there actually is; this may
lead to further damage in various scenarios, such as error
propagation caused data corruption. If uncorrected error (such
as double bit ECC error) happened in memory operation and if the
kernel is unaware of such an event happening, errorneous data may
be propagated to the disk.
Instead GHES memory region should be mapped with page protection
type according to what is returned from arch_apei_get_mem_attribute().
Signed-off-by: Jonathan (Zhixiong) Zhang <zjzhang@codeaurora.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
[ Small stylistic tweaks. ]
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Acked-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1441372302-23242-3-git-send-email-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
There is no need to carry potentially outdated Free Software Foundation
mailing address in file headers since the COPYING file includes it.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
