| Age | Commit message (Collapse) | Author |
|---|
|
The target LPM policy can be set using either a Kconfig or a kernel module
parameter.
However, if the board type is set to anything but board_ahci_low_power,
then the LPM policy will overridden and set to ATA_LPM_UNKNOWN.
Additionally, if the default suspend is suspend to idle, depending on the
hardware capabilities of the HBA, ahci_update_initial_lpm_policy() might
override the LPM policy to either ATA_LPM_MIN_POWER_WITH_PARTIAL or
ATA_LPM_MIN_POWER.
All this means that it is very hard to know which LPM policy a user will
actually be using on a given system.
In order to make it easier to debug LPM related issues, print the LPM
policy on boot.
One common LPM related issue is that the device fails to link up.
Because of that, we cannot add this print to ata_dev_configure(), as that
function is only called after a successful link up. Instead, add the info
using ata_port_desc(), with the help of a new ata_port_desc_misc() helper.
The port description is printed once per port during boot.
Before changes:
ata1: SATA max UDMA/133 abar m524288@0xa5780000 port 0xa5780100 irq 170
ata2: SATA max UDMA/133 abar m524288@0xa5780000 port 0xa5780180 irq 170
After changes:
ata1: SATA max UDMA/133 abar m524288@0xa5780000 port 0xa5780100 irq 170 lpm-pol 4
ata2: SATA max UDMA/133 abar m524288@0xa5780000 port 0xa5780180 irq 170 lpm-pol 4
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
|
|
When a CRC error occurs, the HBA asserts an interrupt to indicate an
interface fatal error (PxIS.IFS). The ISR clears PxIE and PxIS, then
does error recovery. If the adapter receives another SDB FIS
with an error (PxIS.TFES) from the device before the start of the EH
recovery process, the interrupt signaling the new SDB cannot be
serviced as PxIE was cleared already. This in turn results in the HBA
inability to issue any command during the error recovery process after
setting PxCMD.ST to 1 because PxIS.TFES is still set.
According to AHCI 1.3.1 specifications section 6.2.2, fatal errors
notified by setting PxIS.HBFS, PxIS.HBDS, PxIS.IFS or PxIS.TFES will
cause the HBA to enter the ERR:Fatal state. In this state, the HBA
shall not issue any new commands.
To avoid this situation, introduce the function
ahci_port_clear_pending_irq() to clear pending interrupts before
executing a COMRESET. This follows the AHCI 1.3.1 - section 6.2.2.2
specification.
Signed-off-by: Szuying Chen <Chloe_Chen@asmedia.com.tw>
Fixes: e0bfd149973d ("[PATCH] ahci: stop engine during hard reset")
Cc: stable@vger.kernel.org
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
|
|
ahci_exec_polled_cmd() passes its 'unsigned long timeout_msec' parameter
to ata_wait_register() that now takes 'unsigned int' -- eliminate unneeded
implicit casts, not forgetting about ahci_do_softreset()...
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
|
|
sata_deb_timing_{hotplug|long|normal}[] store 'unsigned long' debounce
timeouts in ms, while sata_link_debounce() eventually uses those timeouts
by calling ata_{deadline|msleep}( which take just 'unsigned int'. Change
the debounce timeout table element's type to 'unsigned int' -- all these
timeouts happily fit into 'unsigned int'...
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
|
|
Fix multi-line comment style in ahci_reset_controller() and change the
code to return early if ahci_skip_host_reset is true, reducing
indentation by one level for the bulk of the function code.
No functional changes.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
|
|
Make it explicit that ATA host templates are not modified.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com> (for DWC AHCI SATA)
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com> (for Tegra)
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: John Garry <john.g.garry@oracle.com>
Cc: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20230322195515.1267197-5-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In AHCI specification 1.3.1:
"5.5.3 Processing Completed Commands"
"For each port that has an interrupt pending:
1. Software determines the cause of the interrupt by reading the PxIS
register. It is possible for multiple bits to be set.
2. Software clears appropriate bits in the PxIS register corresponding
to the cause of the interrupt.
3. Software clears the interrupt bit in IS.IPS corresponding to the port.
4. If executing non-queued commands, software reads the PxCI register,
and compares the current value to the list of commands previously
issued by software that are still outstanding. If executing native
queued commands, software reads the PxSACT register and compares the
current value to the list of commands previously issued by software.
Software completes with success any outstanding command whose
corresponding bit has been cleared in the respective register. PxCI
and PxSACT are volatile registers; software should only use their
values to determine commands that have completed, not to determine
which commands have previously been issued.
5. If there were errors, noted in the PxIS register, software performs
error recovery actions (see section 6.2.2)."
The documentation for the PxSACT shadow register in AHCI:
"The device clears bits in this field by sending a Set Device Bits FIS
to the host. The HBA clears bits in this field that are set to ‘1’ in
the SActive field of the Set Device Bits FIS. The HBA only clears bits
that correspond to native queued commands that have completed
successfully."
Additionally, in SATA specification 3.5a:
"11.15 FPDMA QUEUED command protocol"
"DFPDMAQ11: ERROR
Halt command processing and transmit Set Device Bits FIS to host
with the ERR bit in Status field set to one, Interrupt bit set to one,
ATA error code set to one in the ERROR field, bits in ACT field cleared
to zero for any outstanding queued commands, and bits set to one
for any successfully completed queued commands that completion
notification not yet delivered."
I.e. even when the HBA triggers an error interrupt, the HBA will still
clear successfully completed commands in PxSACT. Commands that did not
complete successfully will still have its bit set in PxSACT.
(Which means the command that caused the NCQ error and queued commands
that had not yet finished at the time when the NCQ error occurred.)
Additionally, for a HBA that does not have the libata flag
AHCI_HFLAG_MULTI_MSI set, all ap->locks will point to host->lock, which
means that IRQs will be disabled for one port while another port's IRQ
handler is running. The HBA will still receive FISes from the device,
even if IRQs on the HBA itself are disabled. What can thus e.g. receive
a FIS that completes several commands successfully, followed by a FIS
that does (or does not) complete additional commands with the error bit
set, to indicate that at least one command was aborted.
Therefore, modify ahci_handle_port_interrupt() using the new helper
ahci_qc_complete() to complete the commands that have already been
signaled as successfully through a regular completion SDB FIS, as not
doing so would simply cause successfully completed commands to be
retried for no good reason.
Co-developed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
|
|
Currently, the status is being read for each QC, inside
ata_qc_complete(), which means that QCs being completed by
ata_qc_complete_multiple() (i.e. multiple QCs completed during a single
interrupt), can have different status and error bits set. This is
because the FIS Receive Area will get updated as soon as the HBA
receives a new FIS from the device in the NCQ case.
Here is an example of the problem:
ata14.00: ata_qc_complete_multiple: done_mask: 0x180000
qc tag: 19 cmd: 0x61 flags: 0x11b err_mask: 0x0 tf->status: 0x40
qc tag: 20 cmd: 0x61 flags: 0x11b err_mask: 0x0 tf->status: 0x43
A print in ata_qc_complete_multiple(), shows that done_mask is: 0x180000
which means that tag 19 and 20 were completed. Another print in
ata_qc_complete(), after the call to fill_result_tf(), shows that tag 19
and 20 have different status values, even though they were completed in
the same ata_qc_complete_multiple() call.
If PMP is not enabled, simply read the status and error once, before
calling ata_qc_complete() for each QC. Without PMP, we know that all QCs
must share the same status and error values.
If PMP is enabled, we also read the status before calling
ata_qc_complete(), however, we still read the status for each QC, since
the QCs can belong to different PMP links (which means that the QCs
does not necessarily share the same status and error values).
Do all this by introducing the new port operation .qc_ncq_fill_rtf. If
set, this operation is called in ata_qc_complete_multiple() to set the
result tf for all completed QCs signaled by the last SDB FIS received.
QCs that have their result tf filled are marked with the new flag
ATA_QCFLAG_RTF_FILLED so that any later execution of the qc_fill_rtf
port operation does nothing (e.g. when called from ata_qc_complete()).
Co-developed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
|
|
The boolean return value of the qc_fill_rtf operation is used nowhere.
Simplify this operation interface by making it a void function. All
drivers defining this operation are also updated.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
|
|
The name ATA_QCFLAG_FAILED is misleading since it does not mean that a
QC completed in error, or that it didn't complete at all. It means that
libata decided to schedule EH for the QC, so the QC is now owned by the
libata error handler (EH).
The normal execution path is responsible for not accessing a QC owned
by EH. libata core enforces the rule by returning NULL from
ata_qc_from_tag() for QCs owned by EH.
It is quite easy to mistake that a QC marked with ATA_QCFLAG_FAILED was
an error. However, a QC that was actually an error is instead indicated
by having qc->err_mask set. E.g. when we have a NCQ error, we abort all
QCs, which currently will mark all QCs as ATA_QCFLAG_FAILED. However, it
will only be a single QC that is an error (i.e. has qc->err_mask set).
Rename ATA_QCFLAG_FAILED to ATA_QCFLAG_EH to more clearly highlight that
this flag simply means that a QC is now owned by EH. This new name will
not mislead to think that the QC was an error (which is instead
indicated by having qc->err_mask set).
This also makes it more obvious that the EH code skips all QCs that do
not have ATA_QCFLAG_EH set (rather than ATA_QCFLAG_FAILED), since the EH
code should simply only care about QCs that are owned by EH itself.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
Clean up the code by making use of the newly introduced
ata_port_is_frozen() helper function.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
Currently, for PIO commands, ahci_qc_fill_rtf() reads the status and
error fields from the PIO Setup FIS area of the Received FIS Structure.
For any non-PIO command, ahci_qc_fill_rtf() currently reads the status
and error fields from the D2H Register FIS area of the Received FIS
Structure. This is simply not correct.
According to the SATA 3.5a specification:
11.10 DMA DATA-IN command protocol and 11.11 DMA DATA-OUT command
protocol: READ DMA and WRITE DMA (non-NCQ commands) will end with
the Send_status state, which transmits a Register D2H FIS.
Likewise, in:
11.15 FPDMA QUEUED command protocol: READ FPDMA QUEUED and WRITE FPDMA
QUEUED (NCQ commands) will end with the SendStatus state, which
transmits a Set Device Bits FIS.
So, for NCQ commands, there is never a D2H Register FIS sent.
Reading the status and error fields from the D2H Register FIS area
for a NCQ command, will result in us returning the status and error
values for the last non-NCQ command, which is incorrect.
Update ahci_qc_fill_rtf() to read the status and error fields from
the correct area in the Received FIS Structure for NCQ commands.
Once reason why this has not been detected before, could be because,
in case of an NCQ error, ata_eh_analyze_ncq_error() will overwrite
the (incorrect) status and error values set by ahci_qc_fill_rtf().
However, even successful NCQ commands can have bits set in the status
field (e.g. the sense data available bit), so it is mandatory to read
the status from the correct area also for NCQ commands.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
There are systems with no BIOS or comprehensive embedded firmware which
could be able to properly initialize the SATA AHCI controller
platform-specific capabilities. In that case a good alternative to having
a clever bootloader is to create a device tree node with the properties
well describing all the AHCI-related platform specifics. All the settings
which are normally detected and marked as available in the HBA and its
ports capabilities fields [1] could be defined in the platform DTB by
means of a set of the dedicated properties. Such approach perfectly fits
to the DTB-philosophy - to provide hardware/platform description.
So here we suggest to extend the SATA AHCI device tree bindings with two
additional DT-properties:
1) "hba-cap" - HBA platform generic capabilities like:
- SSS - Staggered Spin-up support.
- SMPS - Mechanical Presence Switch support.
2) "hba-port-cap" - HBA platform port capabilities like:
- HPCP - Hot Plug Capable Port.
- MPSP - Mechanical Presence Switch Attached to Port.
- CPD - Cold Presence Detection.
- ESP - External SATA Port.
- FBSCP - FIS-based Switching Capable Port.
All of these capabilities require to have a corresponding hardware
configuration. Thus it's ok to have them defined in DTB.
Even though the driver currently takes into account the state of the ESP
and FBSCP flags state only, there is nothing wrong with having all of them
supported by the generic AHCI library in order to have a complete OF-based
platform-capabilities initialization procedure. These properties will be
parsed in the ahci_platform_get_resources() method and their values will
be stored in the saved_* fields of the ahci_host_priv structure, which in
its turn then will be used to restore the H.CAP, H.PI and P#.CMD
capability fields on device init and after HBA reset.
Please note this modification concerns the HW-init HBA and its ports flags
only, which are by specification [1] are supposed to be initialized by the
BIOS/platform firmware/expansion ROM and which are normally declared in
the one-time-writable-after-reset register fields. Even though these flags
aren't supposed to be cleared after HBA reset some AHCI instances may
violate that rule so we still need to perform the fields resetting after
each reset. Luckily the corresponding functionality has already been
partly implemented in the framework of the ahci_save_initial_config() and
ahci_restore_initial_config() methods.
[1] Serial ATA AHCI 1.3.1 Specification, p. 103
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
There is no point in reading the AHCI version all over in the tail of the
ahci_save_initial_config() method. That register is RO and doesn't change
its value even after reset. So just reuse the data, which has already been
read from there earlier in the head of the function.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
Currently there are four port-map-related fields declared in the
ahci_host_priv structure and used to setup the HBA ports mapping. First
the ports-mapping is read from the PI register and immediately stored in
the saved_port_map field. If forced_port_map is initialized with non-zero
value then its value will have greater priority over the value read from
PI, thus it will override the saved_port_map field. That value will be
then masked by a non-zero mask_port_map field and after some sanity checks
it will be stored in the ahci_host_priv.port_map field as a final port
mapping.
As you can see the logic is a bit too complicated for such a simple task.
We can freely get rid from at least one of the fields with no change to
the implemented semantic. The force_port_map field can be replaced with
taking non-zero saved_port_map value into account. So if saved_port_map is
pre-initialized by the low level drivers (platform drivers) then it will
have greater priority over the value read from PI register and will be
used as actual HBA ports mapping later on. Thus the ports map forcing task
will be just transferred from force_port_map to the saved_port_map field.
This modification will perfectly fit into the feature of having OF-based
initialization of the HW-init HBA CSR fields we are about to introduce in
the next commit.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
Add the explicit error and status register fields to 'struct ata_taskfile'
using the anonymous *union*s ('struct ide_taskfile' had that for ages!) and
update the libata taskfile code accordingly. There should be no object code
changes resulting from that...
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
Drop pointless VPRINTK() calls for entering and existing interrupt
routines and convert the remaining calls to dev_dbg().
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
To follow the flow of control we should be using tracepoints, as
they will tie in with the actual I/O flow and deliver a better
overview about what it happening.
This patch adds tracepoints for hard reset, soft reset, and postreset
and adds them in the libata-eh control flow.
With that we can drop the reset DPRINTK calls in the various drivers.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
Add an ata_port_classify() helper to print out the results from
the device classification and remove the debugging statements
from ata_dev_classify().
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
Debugging messages in pci init functions or sg setup are pretty
much pointless, as the workflow pretty much decides what happened.
So drop them.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
The StorageD3Enable _DSD is used for the vendor to indicate that the disk
should be opted into or out of a different behavior based upon the platform
design.
For AMD's Renoir and Green Sardine platforms it's important that any
attached SATA storage has transitioned into DevSlp when s2idle is used.
If the disk is left in active/partial/slumber, then the system is not able
to resume properly.
When the StorageD3Enable _DSD is detected, check the system is using s2idle
and DevSlp is enabled and if so explicitly wait long enough for the disk to
enter DevSlp.
Cc: Nehal-bakulchandra Shah <Nehal-bakulchandra.Shah@amd.com>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214091
Link: https://docs.microsoft.com/en-us/windows-hardware/design/component-guidelines/power-management-for-storage-hardware-devices-intro
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
ahci_shost_attr_group is referenced only in drivers/ata/libahci.c.
Declare it as static.
Fixes: c3f69c7f629f ("scsi: ata: Switch to attribute groups")
Cc: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
|
struct device supports attribute groups directly but does not support
struct device_attribute directly. Hence switch to attribute groups.
Link: https://lore.kernel.org/r/20211012233558.4066756-3-bvanassche@acm.org
Acked-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Currently, the only way a user can determine if a SATA device supports
NCQ priority is to try to enable the use of this feature using the
ncq_prio_enable sysfs device attribute. If enabling the feature fails,
it is because the device does not support NCQ priority. Otherwise, the
feature is enabled and success indicates that the device supports NCQ
priority.
Improve this odd interface by introducing the read-only
ncq_prio_supported sysfs device attribute to indicate if a SATA device
supports NCQ priority. The value of this attribute reflects the status
of device flag ATA_DFLAG_NCQ_PRIO, which is set only for devices
supporting NCQ priority.
Add this new sysfs attribute to the device attributes group of libahci
and libata-sata.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Link: https://lore.kernel.org/r/20210816014456.2191776-10-damien.lemoal@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
On Hisilicon Kunpeng920, ESP is set to 1 by default for all ports of
SATA controller. In some scenarios, some ports are not external SATA ports,
and it cause disks connected to these ports to be identified as removable
disks. So disable the SXS capability on the software side to prevent users
from mistakenly considering non-removable disks as removable disks and
performing related operations.
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/1615544676-61926-1-git-send-email-luojiaxing@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In case a driver wants to return an error from qc_prep, return enum
ata_completion_errors. sata_mv is one of those drivers -- see the next
patch. Other drivers return the newly defined AC_ERR_OK.
[v2] use enum ata_completion_errors and AC_ERR_OK.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-ide@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The commit ed08d40cdec4
("ahci: Changing two module params with static and __read_mostly")
moved ahci_em_messages to be static while missing the fact of exporting it.
WARNING: "ahci_em_messages" [vmlinux] is a static EXPORT_SYMBOL_GPL
Drop export for the local variable ahci_em_messages.
Fixes: ed08d40cdec4 ("ahci: Changing two module params with static and __read_mostly")
Cc: Chuansheng Liu <chuansheng.liu@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In commit af7ddd8a627c
("Merge tag 'dma-mapping-4.21' of git://git.infradead.org/users/hch/dma-mapping"),
dmam_alloc_coherent has already zeroed the memory.
So memset is not needed.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 or at your option any
later version this program is distributed in the hope that it will
be useful but without any warranty without even the implied warranty
of merchantability or fitness for a particular purpose see the gnu
general public license for more details you should have received a
copy of the gnu general public license along with this program see
the file copying if not write to the free software foundation 675
mass ave cambridge ma 02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 52 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154042.342335923@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
handler implemented
For an AHCI controller with AHCI_HFLAG_MULTI_MSI flag set, we may get the
following log, regardless of whether a custom irq handler was implemented
or not:
[ 14.700238] ahci 0000:74:03.0: both AHCI_HFLAG_MULTI_MSI flag set and custom irq handler implemented
This is because we can set hpriv->irq_handler to
ahci_single_level_irq_intr() if not already set, in
ahci_init_one()->ahci_pci_save_initial_config()->ahci_save_initial_config().
Stop having this warn being misleading by adding a check for
hpriv->irq_handler != ahci_single_level_irq_intr.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata updates from Tejun Heo:
"Nothing too interesting. Mostly ahci and ahci_platform changes, many
around power management"
* 'for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (22 commits)
ata: ahci_platform: enable to get and control reset
ata: libahci_platform: add reset control support
ata: add an extra argument to ahci_platform_get_resources()
ata: sata_rcar: Add r8a77965 support
ata: sata_rcar: exclude setting of PHY registers in Gen3
ata: sata_rcar: really mask all interrupts on Gen2 and later
Revert "ata: ahci_platform: allow disabling of hotplug to save power"
ata: libahci: Allow reconfigure of DEVSLP register
ata: libahci: Correct setting of DEVSLP register
ata: ahci: Enable DEVSLP by default on x86 with SLP_S0
ata: ahci: Support state with min power but Partial low power state
Revert "ata: ahci_platform: convert kcalloc to devm_kcalloc"
ata: sata_rcar: Add rudimentary Runtime PM support
ata: sata_rcar: Provide a short-hand for &pdev->dev
ata: Only output sg element mapped number in verbose debug
ata: Guard ata_scsi_dump_cdb() by ATA_VERBOSE_DEBUG
ata: ahci_platform: convert kcalloc to devm_kcalloc
ata: ahci_platform: convert kzallloc to kcalloc
ata: ahci_platform: correct parameter documentation for ahci_platform_shutdown
libata: remove ata_sff_data_xfer_noirq()
...
|
|
There are two modes in which DEVSLP can be entered. The OS initiated or
hardware autonomous.
In hardware autonomous mode, BIOS configures the AHCI controller and the
device to enable DEVSLP. But they may not be ideal for all cases. So in
this case, OS should be able to reconfigure DEVSLP register.
Currently if the DEVSLP is already enabled, we can't set again as it will
simply return. There are some systems where the firmware is setting high
DITO by default, in this case we can't modify here to correct settings.
With the default in several seconds, we are not able to transition to
DEVSLP.
This change will allow reconfiguration of devslp register if DITO is
different.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
We have seen that on some platforms, SATA device never show any DEVSLP
residency. This prevent power gating of SATA IP, which prevent system
to transition to low power mode in systems with SLP_S0 aka modern
standby systems. The PHY logic is off only in DEVSLP not in slumber.
Reference:
https://www.intel.com/content/dam/www/public/us/en/documents/datasheets
/332995-skylake-i-o-platform-datasheet-volume-1.pdf
Section 28.7.6.1
Here driver is trying to do read-modify-write the devslp register. But
not resetting the bits for which this driver will modify values (DITO,
MDAT and DETO). So simply reset those bits before updating to new values.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Currently when min_power policy is selected, the partial low power state
is not entered and link will try aggressively enter to only slumber state.
Add a new policy which still enable DEVSLP but also try to enter partial
low power state. This policy is presented as "min_power_with_partial".
For information the difference between partial and slumber
Partial – PHY logic is powered up, and in a reduced power state. The link
PM exit latency to active state maximum is 10 ns.
Slumber – PHY logic is powered up, and in a reduced power state. The link
PM exit latency to active state maximum is 10 ms.
Devslp – PHY logic is powered down. The link PM exit latency from this
state to active state maximum is 20 ms, unless otherwise specified by
DETO.
Suggested-and-reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Currently smatch warns of possible Spectre-V1 issue in ahci_led_store():
drivers/ata/libahci.c:1150 ahci_led_store() warn: potential spectre issue 'pp->em_priv' (local cap)
Userspace controls @pmp from following callchain:
em_message->store()
->ata_scsi_em_message_store()
-->ap->ops->em_store()
--->ahci_led_store()
After the mask+shift @pmp is effectively an 8b value, which is used to
index into an array of length 8, so sanitize the array index.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
This change balances out the final ahci_port_resume in port_start to
ensure reference counts are correct after port stop.
Signed-off-by: Samuel Morris <samorris@lexmark.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata updates from Tejun Heo:
- libata has always been limiting the maximum queue depth to 31, with
one entry set aside mostly for historical reasons. This didn't use to
make much difference but Jens found out that modern hard drives can
actually perform measurably better with the extra one queue depth.
Jens updated libata core so that it can make use of full 32 queue
depth
- Damien updated command retry logic in error handling so that it
doesn't unnecessarily retry when upper layer (SCSI) is gonna handle
them
- A couple misc changes
* 'for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
sata_fsl: use the right type for tag bitshift
ahci: enable full queue depth of 32
libata: don't clamp queue depth to ATA_MAX_QUEUE - 1
libata: add extra internal command
sata_nv: set host can_queue count appropriately
libata: remove assumption that ATA_MAX_QUEUE - 1 is the max
libata: use ata_tag_internal() consistently
libata: bump ->qc_active to a 64-bit type
libata: convert core and drivers to ->hw_tag usage
libata: introduce notion of separate hardware tags
libata: Fix command retry decision
libata: Honor RQF_QUIET flag
libata: Make ata_dev_set_mode() less verbose
libata: Fix ata_err_string()
libata: Fix comment typo in ata_eh_analyze_tf()
sata_nv: don't use block layer bounce buffer
ata: hpt37x: Convert to use match_string() helper
|
|
Anything that goes to the hardware should use ->hw_tag, anything
related to internal lookup should be using ->tag.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Marvell armada37xx, armada7k and armada8k share the same
AHCI sata controller IP, and currently there is an issue
(Errata Ref#226)that the SATA can not be detected via SATA
Port-MultiPlayer(PMP). After debugging, the reason is
found that the value of Port-x FIS-based Switching Control
(PxFBS@0x40) became wrong.
According to design, the bits[11:8, 0] of register PxFBS
are cleared when Port Command and Status (0x18) bit[0]
changes its value from 1 to 0, i.e. falling edge of Port
Command and Status bit[0] sends PULSE that resets PxFBS
bits[11:8; 0].
So it needs save the port PxFBS register before PxCMD
ST write and restore the port PxFBS register afterwards
in ahci_stop_engine().
This commit allows drivers to override ahci_stop_engine
behavior for use by the Marvell AHCI driver(and potentially
other drivers in the future).
Signed-off-by: Evan Wang <xswang@marvell.com>
Cc: Ofer Heifetz <oferh@marvell.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Exit directly with ENODEV, if the AHCI controller is not available
anymore. Otherwise a delay of 500ms for each port is added to the remove
function while trying to issue a command on the non-existent controller.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. Adds a pointer back to link
structure.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: linux-ide@vger.kernel.org
Link: https://lkml.kernel.org/r/20171016215658.GA101965@beast
|
|
While most hardware will simply ignore a write to a read-only register,
some hardware will signal an abort if this occurs.
This commit introduces the flag AHCI_HFLAG_NO_WRITE_TO_RO to prevent the
AHCI library from attempting to write to the HOST_CAP, HOST_CAP2, and
HOST_PORTS_IMPL registers which may be read-only.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Some hardware is capable of supporting Aggresive Link Power Management
even though it is not indicated by the Host Capability register.
This commit adds the AHCI_HFLAG_YES_ALPM flag to the AHCI library to
allow indication of this quirk when the Host Capability register is
Read Only and therefore cannot be changed.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
AHCI 1.3.1 Spec says that software shall build two H2D register
FISes in the command list to send a software reset.
The comments in ahci_do_softreset() is currently D2H instead of H2D.
Signed-off-by: Minwoo Im <dn3108@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
The libata documentation is now using ReST. Update references
to it to point to the new place.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
We need a way to retrieve the information about the online state of
the link in the ahci-da850 driver.
Create a new function: ahci_do_hardreset() which is called from
ahci_hardreset() for backwards compatibility, but has an additional
argument: 'online' - which can be used to check if the link is online
after this function returns.
The new routine will be used in the ahci-da850 driver to avoid code
duplication when implementing a workaround for tha da850 SATA
controller quirk/instability.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Add a sysfs entry to turn on priority information being passed
to a ATA device. By default this feature is turned off.
This patch depends on ata: Enabling ATA Command Priorities
tj: Renamed ncq_prio_on to ncq_prio_enable and removed trivial
ata_ncq_prio_on() and open-coded the test.
Signed-off-by: Adam Manzanares <adam.manzanares@hgst.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Use the new pci_alloc_irq_vectors API to allocate MSI-X and MSI vectors.
The big advantage over the old code is that we can use the same API for
MSI and MSI-X, and that we don't need to store the MSI-X vector mapping
in driver-private data structures.
This first conversion keeps the probe order as-is: MSI-X multi vector,
MSI multi vector, MSI single vector, MSI-X single vector and last a
single least legacy interrupt line. There is one small change of
behavior: we now check the "MSI Revert to Single Message" flag for
MSI-X in addition to MSI.
Because the API to find the Linux IRQ number for a MSI/MSI-X vector
is PCI specific, but libahaci is bus-agnostic I had to a
get_irq_vector function pointer to struct ahci_host_priv. The
alternative would be to move the multi-vector case of ahci_host_activate
to ahci.c and just call ata_host_activate directly from the others
users of ahci_host_activate.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
|
|
irq already contains the interrupt number for the port, don't add the
port index to it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: d684a90d38e2 ("ahci: per-port msix support")
Cc: stable@vger.kernel.org v4.5+
|
