| Age | Commit message (Collapse) | Author |
|---|
|
Implement the TCG I2C Interface driver, as specified in the TCG PC
Client Platform TPM Profile (PTP) specification for TPM 2.0 v1.04
revision 14, section 8, I2C Interface Definition.
This driver supports Guard Times. That is, if required by the TPM, the
driver has to wait by a vendor-specific time after each I2C read/write.
The specific time is read from the TPM_I2C_INTERFACE_CAPABILITY register.
Unfortunately, the TCG specified almost but not quite compatible
register addresses. Therefore, the TIS register addresses need to be
mapped to I2C ones. The locality is stripped because for now, only
locality 0 is supported.
Add a sanity check to I2C reads of e.g. TPM_ACCESS and TPM_STS. This is
to detect communication errors and issues due to non-standard behaviour
(E.g. the clock stretching quirk in the BCM2835, see 4dbfb5f4401f). In
case the sanity check fails, attempt a retry.
Co-developed-by: Johannes Holland <johannes.holland@infineon.com>
Signed-off-by: Johannes Holland <johannes.holland@infineon.com>
Co-developed-by: Amir Mizinski <amirmizi6@gmail.com>
Signed-off-by: Amir Mizinski <amirmizi6@gmail.com>
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
Add TPM 2.0 compatible I2C interface for chips with cr50 firmware.
The firmware running on the currently supported H1 MCU requires a
special driver to handle its specific protocol, and this makes it
unsuitable to use tpm_tis_core_* and instead it must implement the
underlying TPM protocol similar to the other I2C TPM drivers.
- All 4 bytes of status register must be read/written at once.
- FIFO and burst count is limited to 63 and must be drained by AP.
- Provides an interrupt to indicate when read response data is ready
and when the TPM is finished processing write data.
This driver is based on the existing infineon I2C TPM driver, which
most closely matches the cr50 i2c protocol behavior.
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.com>
Signed-off-by: Adrian Ratiu <adrian.ratiu@collabora.com>
Tested-by: Adrian Ratiu <adrian.ratiu@collabora.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
When fitted, the SynQuacer platform exposes its SPI TPM via a MMIO
window that is backed by the SPI command sequencer in the SPI bus
controller. This arrangement has the limitation that only byte size
accesses are supported, and so we'll need to provide a separate module
that take this into account.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Revert tpm_tis_spi_mod.ko back to tpm_tis_spi.ko as the rename could
break user space scripts. This can be achieved by renaming tpm_tis_spi.c
as tpm_tis_spi_main.c. Then tpm_tis_spi-y can be used inside the
makefile.
Cc: Andrey Pronin <apronin@chromium.org>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: stable@vger.kernel.org # 5.5.x
Fixes: 797c0113c9a4 ("tpm: tpm_tis_spi: Support cr50 devices")
Reported-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Tested-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Add TPM2.0 PTP FIFO compatible SPI interface for chips with Cr50
firmware. The firmware running on the currently supported H1 Secure
Microcontroller requires a special driver to handle its specifics:
- need to ensure a certain delay between SPI transactions, or else
the chip may miss some part of the next transaction
- if there is no SPI activity for some time, it may go to sleep,
and needs to be waken up before sending further commands
- access to vendor-specific registers
Cr50 firmware has a requirement to wait for the TPM to wakeup before
sending commands over the SPI bus. Otherwise, the firmware could be in
deep sleep and not respond. The method to wait for the device to wakeup
is slightly different than the usual flow control mechanism described in
the TCG SPI spec. Add a completion to tpm_tis_spi_transfer() before we
start a SPI transfer so we can keep track of the last time the TPM
driver accessed the SPI bus to support the flow control mechanism.
Split the cr50 logic off into a different file to keep it out of the
normal code flow of the existing SPI driver while making it all part of
the same module when the code is optionally compiled into the same
module. Export a new function, tpm_tis_spi_init(), and the associated
read/write/transfer APIs so that we can do this. Make the cr50 code wrap
the tpm_tis_spi_phy struct with its own struct to override the behavior
of tpm_tis_spi_transfer() by supplying a custom flow control hook. This
shares the most code between the core driver and the cr50 support
without combining everything into the core driver or exporting module
symbols.
Signed-off-by: Andrey Pronin <apronin@chromium.org>
Cc: Andrey Pronin <apronin@chromium.org>
Cc: Duncan Laurie <dlaurie@chromium.org>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guenter Roeck <groeck@chromium.org>
Cc: Alexander Steffen <Alexander.Steffen@infineon.com>
Cc: Heiko Stuebner <heiko@sntech.de>
[swboyd@chromium.org: Replace boilerplate with SPDX tag, drop
suspended bit and remove ifdef checks in cr50.h, migrate to functions
exported in tpm_tis_spi.h, combine into one module instead of two]
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Add a driver for a firmware TPM running inside TEE.
Documentation of the firmware TPM:
https://www.microsoft.com/en-us/research/publication/ftpm-software-implementation-tpm-chip/ .
Implementation of the firmware TPM:
https://github.com/Microsoft/ms-tpm-20-ref/tree/master/Samples/ARM32-FirmwareTPM
Tested-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-by: Thirupathaiah Annapureddy <thiruan@microsoft.com>
Signed-off-by: Thirupathaiah Annapureddy <thiruan@microsoft.com>
Co-authored-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Factor out TPM 1.x commands calculation into tpm1-cmd.c file.
and change the prefix from tpm_ to tpm1_.
No functional change is done here.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Make the tpm Makefile a bit more in order by putting
objects in one column.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Functions and structures specific to TPM1 are renamed from tpm* to tpm1*.
Signed-off-by: Thiebaud Weksteen <tweek@google.com>
Suggested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Signed-off-by: Thiebaud Weksteen <tweek@google.com>
Suggested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
If we are not able to retrieve the TPM event logs from the ACPI table,
check the EFI configuration table (Linux-specific GUID).
The format version of the log is now returned by the provider function.
Signed-off-by: Thiebaud Weksteen <tweek@google.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Rename the current TPM Event Log provider files (ACPI and OF)
for clarity.
Signed-off-by: Thiebaud Weksteen <tweek@google.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently the tpm spaces are not exposed to userspace. Make this
exposure via a separate device, which can now be opened multiple times
because each read/write transaction goes separately via the space.
Concurrency is protected by the chip->tpm_mutex for each read/write
transaction separately. The TPM is cleared of all transient objects
by the time the mutex is dropped, so there should be no interference
between the kernel and userspace.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Added an ability to virtualize TPM commands into an isolated context
that we call a TPM space because the word context is already heavily
used in the TPM specification. Both the handle areas and bodies (where
necessary) are virtualized.
The mechanism works by adding a new parameter struct tpm_space to the
tpm_transmit() function. This new structure contains the list of virtual
handles and a buffer of page size (currently) for backing storage.
When tpm_transmit() is called with a struct tpm_space instance it will
execute the following sequence:
1. Take locks.
2. Load transient objects from the backing storage by using ContextLoad
and map virtual handles to physical handles.
3. Perform the transaction.
4. Save transient objects to backing storage by using ContextSave and
map resulting physical handle to virtual handle if there is such.
This commit does not implement virtualization support for hmac and
policy sessions.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Unlike the device driver support for TPM 1.2, the TPM 2.0 does
not support the securityfs pseudo files for displaying the
firmware event log.
This patch enables support for providing the TPM 2.0 event log in
binary form. TPM 2.0 event log supports a crypto agile format that
records multiple digests, which is different from TPM 1.2. This
patch enables the tpm_bios_log_setup for TPM 2.0 and adds the
event log parser which understand the TPM 2.0 crypto agile format.
Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Kenneth Goldman <kgold@linux.vnet.ibm.com>
Tested-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Currently, read_log() has two implementations: one for ACPI platforms
and the other for device tree(OF) based platforms. The proper one is
selected at compile time using Kconfig and #ifdef in the Makefile,
which is not the recommended approach.
This patch removes the #ifdef in the Makefile by defining a single
read_log() method, which checks for ACPI/OF event log properties at
runtime.
[jarkko.sakkinen@linux.intel.com: added tpm_ prefix to read_log*]
Suggested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Spi protocol standardized by the TCG is now supported by most of TPM
vendors.
It supports SPI Bit Protocol as describe in the TCG PTP
specification (chapter 6.4.6 SPI Bit Protocol).
Irq mode is not supported.
This commit is based on the initial work by Peter Huewe.
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
To avoid code duplication between the old tpm_tis and the new and future
native tcg tis driver(ie: spi, i2c...), the tpm_tis driver was reworked,
so that all common logic is extracted and can be reused from all drivers.
The core methods can also be used from other TIS like drivers.
itpm workaround is now managed with a specific tis flag
TPM_TIS_ITPM_POSSIBLE.
This commit is based on the initial work by Peter Huewe.
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
This patch implements a proxy driver for supporting multiple emulated TPMs
in a system.
The driver implements a device /dev/vtpmx that is used to created
a client device pair /dev/tpmX (e.g., /dev/tpm10) and a server side that
is accessed using a file descriptor returned by an ioctl.
The device /dev/tpmX is the usual TPM device created by the core TPM
driver. Applications or kernel subsystems can send TPM commands to it
and the corresponding server-side file descriptor receives these
commands and delivers them to an emulated TPM.
The driver retrievs the TPM 1.2 durations and timeouts. Since this requires
the startup of the TPM, we send a startup for TPM 1.2 as well as TPM 2.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
CC: linux-kernel@vger.kernel.org
CC: linux-doc@vger.kernel.org
CC: linux-api@vger.kernel.org
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
tpm_i2c_stm_st33 is a TIS 1.2 TPM with a core interface which can be used
by different phy such as i2c or spi. The core part is called st33zp24 which
is also the main part reference.
include/linux/platform_data/tpm_stm_st33.h is renamed consequently.
The driver is also split into an i2c phy in charge of sending/receiving
data as well as managing platform data or dts configuration.
Acked-by: Jarkko Sakkinen <jarkko.sakknen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jason.gunthorpe@obsidianresearch.com>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
|
|
tpm_crb is a driver for TPM 2.0 Command Response Buffer (CRB) Interface
as defined in PC Client Platform TPM Profile (PTP) Specification.
Only polling and single locality is supported as these are the limitations
of the available hardware, Platform Trust Techonlogy (PTT) in Haswell
CPUs.
The driver always applies CRB with ACPI start because PTT reports using
only ACPI start as start method but as a result of my testing it requires
also CRB start.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jasob Gunthorpe <jason.gunthorpe@obsidianresearch.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
|
|
TPM 2.0 devices are separated by adding a field 'flags' to struct
tpm_chip and defining a flag TPM_CHIP_FLAG_TPM2 for tagging them.
This patch adds the following internal functions:
- tpm2_get_random()
- tpm2_get_tpm_pt()
- tpm2_pcr_extend()
- tpm2_pcr_read()
- tpm2_startup()
Additionally, the following exported functions are implemented for
implementing TPM 2.0 device drivers:
- tpm2_do_selftest()
- tpm2_calc_ordinal_durations()
- tpm2_gen_interrupt()
The existing functions that are exported for the use for existing
subsystems have been changed to check the flags field in struct
tpm_chip and use appropriate TPM 2.0 counterpart if
TPM_CHIP_FLAG_TPM2 is est.
The code for tpm2_calc_ordinal_duration() and tpm2_startup() were
originally written by Will Arthur.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Will Arthur <will.c.arthur@intel.com>
Reviewed-by: Jasob Gunthorpe <jason.gunthorpe@obsidianresearch.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Tested-by: Peter Huewe <peterhuewe@gmx.de>
[phuewe: Fixed copy paste error * 2]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
|
|
tpm_register_hardware() and tpm_remove_hardware() are called often
before initializing the device. The problem is that the device might
not be fully initialized when it comes visible to the user space.
This patch resolves the issue by diving initialization into two
parts:
- tpmm_chip_alloc() creates struct tpm_chip.
- tpm_chip_register() sets up the character device and sysfs
attributes.
The framework takes care of freeing struct tpm_chip by using the devres
API. The broken release callback has been wiped. ACPI drivers do not
ever get this callback.
Regards to Jason Gunthorpe for carefully reviewing this part of the
code.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jasob Gunthorpe <jason.gunthorpe@obsidianresearch.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: Scot Doyle <lkml14@scotdoyle.com>
Tested-by: Peter Huewe <peterhuewe@gmx.de>
[phuewe: update to upstream changes]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
|
|
product
STMicroelectronics i2c tpm is the only one to have a different tristate
label.
Rename it "TPM Interface Specification 1.2 Interface (I2C - STMicroelectronics)"
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
[phuewe: corrected module name in the helptext]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
|
|
CLASS-sysfs.c is a common idiom for linux subsystems.
This is the first step to pulling all the sysfs support code from
the drivers into tpm-sysfs. This is a plain text copy from tpm-interface
with support changes to make it compile.
_tpm_pcr_read is made non-static and is called tpm_pcr_read_dev.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
|
|
CLASS-dev.c is a common idiom for Linux subsystems
This pulls all the code related to the miscdev into tpm-dev.c and makes it
static. The identical file_operation structs in the drivers are purged and the
tpm common code unconditionally creates the miscdev.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Joel Schopp <jschopp@linux.vnet.ibm.com>
Reviewed-by: Ashley Lai <adlai@linux.vnet.ibm.com>
[phuewe:
tpm_dev_release is now used only in this file, thus the EXPORT_SYMBOL
can be dropped and the function be marked as static.
It has no other in-kernel users]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
|
|
This is based on the work of Teddy Reed <teddy@prosauce.org> published
on GitHub:
https://github.com/theopolis/tpm-i2c-atmel.git
34894b988b67e0ae55088d6388e77b0dbf10c07d
That driver was never merged, I have taken it as a starting port,
forward ported, tested and revised the driver:
- Make it broadly textually similar to the Infineon and Nuvoton I2C
driver
- Place everything in a format suitable for mainline inclusion
- Use high level I2C functions i2c_master_send and
i2c_master_recv for data xfer
- Use the timeout system from the core code, by faking out a status
register
- Only I2C transfer the number of bytes in the reply, not a fixed
message size.
- checkpatch cleanups
- Testing on ARM Kirkwood, with this device tree, using a
AT97SC3204T-X1A180
tpm@29 {
compatible = "atmel,at97sc3204t";
reg = <0x29>;
};
Signed-off-by: Teddy Reed <teddy@prosauce.org>
[jgg: revised and tested]
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
[phuewe: minor whitespace changes]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
|
|
This chip is/was also branded as a Winbond WPCT301.
Originally written by Dan Morav <dmorav@nuvoton.com> and posted to LKML:
https://lkml.org/lkml/2011/9/7/206
The original posting was not merged, I have taken it as a
starting point, forward ported, tested and revised the driver:
- Rework interrupt handling to work properly with level triggered
interrupts. The old version just locked up.
- Synchronize various items with Peter Huewe's Infineon driver:
* Add durations/timeouts sysfs calls
* Remove I2C device auto-detection
* Don't fiddle with chip->release
* Call tpm_dev_vendor_release in the probe error path
* Use MODULE_DEVICE_TABLE for the I2C ids
* Provide OF compatible strings for DT support
* Use SIMPLE_DEV_PM_OPS
* Use module_i2c_driver
- checkpatch cleanups
- Testing on ARM Kirkwood with GPIO interrupts, with this device tree:
tpm@57 {
compatible = "nuvoton,npct501";
reg = <0x57>;
interrupt-parent = <&gpio1>;
interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
};
Signed-off-by: Dan Morav <dmorav@nuvoton.com>
[jgg: revised and tested]
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
[phuewe: minor whitespace changes, fixed module name in kconfig]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
|
|
Now that we can have multiple .c files in the tpm module there is
no reason for tpm-bios.
tpm-bios exported several functions: tpm_bios_log_setup,
tpm_bios_log_teardown, tpm_add_ppi, and tpm_remove_ppi.
They are only used by tpm, and if tpm-bios is built then
tpm will unconditionally require them. Further, tpm-bios does
nothing on its own, it has no module_init function.
Thus we remove the exports and merge the modules to simplify things.
The Makefile conditions are changed slightly to match the code,
tpm_ppi is always required if CONFIG_ACPI is set.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
|
|
This is preparation for making the tpm module multi-file. kbuild does
not like having a .c file with the same name as a module. We wish to
keep the tpm module name so that userspace doesn't see this change.
tpm-interface.c is chosen because the next several commits in the series
migrate items into tpm-sysfs.c, tpm-dev.c and tpm-class.c. All that will
be left is tpm command processing and interfacing code.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
|
|
This is a complete rewrite of the Xen TPM frontend driver, taking
advantage of a simplified frontend/backend interface and adding support
for cancellation and timeouts. The backend for this driver is provided
by a vTPM stub domain using the interface in Xen 4.3.
Signed-off-by: Daniel De Graaf <dgdegra@tycho.nsa.gov>
Acked-by: Matthew Fioravante <matthew.fioravante@jhuapl.edu>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
* STMicroelectronics version 1.2.0, Copyright (C) 2010
* STMicroelectronics comes with ABSOLUTELY NO WARRANTY.
* This is free software, and you are welcome to redistribute it
* under certain conditions.
This is the driver for TPM chip from ST Microelectronics.
If you have a TPM security chip from STMicroelectronics working with
an I2C, in menuconfig or .config choose the tpm driver on
device --> tpm and activate the protocol of your choice before compiling
the kernel.
The driver will be accessible from within Linux.
Tested on linux x86/x64, beagleboard REV B & XM REV C and CHROMIUM OS
Signed-off-by: Mathias Leblanc <mathias.leblanc@st.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
|
|
The Physical Presence Interface enables the OS and the BIOS to cooperate and
provides a simple and straightforward platform user experience for
administering the TPM without sacrificing security.
V2: separate the patch out in a separate source file,
add #ifdef CONFIG_ACPI so it compiles out on ppc,
use standard error instead of ACPI error as return code of show/store fns.
V3: move #ifdef CONFIG_ACPI from .c file to .h file.
V4: move tpm_ppi code from tpm module to tpm_bios module.
V5: modify sys_add_ppi() so that ppi_attr_grp doesn't need to be exported
Signed-off-by: Xiaoyan Zhang <xiaoyan.zhang@intel.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
|
|
This patch retrieves the event log data from the device tree
during file open. The event log data will then displayed through
securityfs.
Signed-off-by: Ashley Lai <adlai@us.ibm.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
|
|
This patch adds a new device driver to support IBM virtual TPM
(vTPM) for PPC64. IBM vTPM is supported through the adjunct
partition with firmware release 740 or higher. With vTPM
support, each lpar is able to have its own vTPM without the
physical TPM hardware.
This driver provides TPM functionalities by communicating with
the vTPM adjunct partition through Hypervisor calls (Hcalls)
and Command/Response Queue (CRQ) commands.
Signed-off-by: Ashley Lai <adlai@us.ibm.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
|
|
Break ACPI-specific pieces of the event log handling into their own file
and create tpm_eventlog.[ch] to store common event log handling code.
This will be required to integrate future event log sources on platforms
without ACPI tables.
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
|
|
This patch adds a driver to support Infineon's SLB 9635 TT 1.2 Soft I2C TPMs
which follow the TGC TIS 1.2 TPM specification[1] and Infineon's I2C Protocol
Stack Specification 0.20.
The I2C Protocol Stack Specification is a simple adaption of the LPC TIS
Protocol to the I2C Bus.
The I2C TPMs can be used when LPC Bus is not available (i.e. non x86
architectures like ARM).
The driver is based on the tpm_tis.c driver by Leendert van Dorn and Kyleen
Hall and has quite similar functionality.
Tested on Nvidia ARM Tegra2 Development Platform and Beagleboard (ARM OMAP)
Tested with the Trousers[2] TSS API Testsuite v 0.3 [3]
Compile-tested on x86 (32/64-bit)
Updates since version 2.1.4:
- included "Lock the I2C adapter for a sequence of requests", by Bryan Freed
- use __i2c_transfer instead of own implementation of unlocked i2c_transfer
- use struct dev_pm_ops for power management via SIMPLE_DEV_PM_OPS
Updates since version 2.1.3:
- use proper probing mechanism
* either add the tpm using I2C_BOARD_INFO to your board file or probe it
* during runtime e.g on BeagleBoard using :
* "echo tpm_i2c_infineon 0x20 > /sys/bus/i2c/devices/i2c-2/new_device"
- fix possible endless loop if hardware misbehaves
- improved return codes
- consistent spelling i2c/tpm -> I2C/TPM
- remove hardcoded sleep values and msleep usage
- removed debug statements
- added check for I2C functionality
- renaming to tpm_i2c_infineon
Updates since version 2.1.2:
- added sysfs entries for duration and timeouts
- updated to new tpm_do_selftest
Updates since version 2.1.0:
- improved error handling
- implemented workarounds needed by the tpm
- fixed typos
References:
[1]
http://www.trustedcomputinggroup.org/resources/pc_client_work_group_pc_client_
specific_tpm_interface_specification_tis_version_12/
[2] http://trousers.sourceforge.net/
[3]
http://sourceforge.net/projects/trousers/files/TSS%20API%20test%20suite/0.3/
Reviewed-by: Andi Shyti <andi.shyti@gmail.com>
Acked-by: Marcel Selhorst <tpmdd@selhorst.net>
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Signed-off-by: Bryan Freed <bfreed@chromium.org>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
|
|
The driver for the next generation of TPM chips version 1.2 including support
for interrupts. The Trusted Computing Group has written the TPM Interface
Specification (TIS) which defines a common interface for all manufacturer's
1.2 TPM's thus the name tpm_tis.
Signed-off-by: Leendert van Doorn <leendert@watson.ibm.com>
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
According to the TCG specifications measurements or hashes of the BIOS code
and data are extended into TPM PCRS and a log is kept in an ACPI table of
these extensions for later validation if desired. This patch exports the
values in the ACPI table through a security-fs seq_file.
Signed-off-by: Seiji Munetoh <munetoh@jp.ibm.com>
Signed-off-by: Stefan Berger <stefanb@us.ibm.com>
Signed-off-by: Reiner Sailer <sailer@us.ibm.com>
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch provides a new device driver for the Infineon SLD 9630 TT Trusted
Platform Module (TPM 1.1b) [1] which is embedded on Intel- mainboards or in
HP/ Fujitsu-Siemens / Toshiba-Notebooks. A nearly complete list where this
module is integrated in can be found in [2].
This kernel module acts as a communication gateway between the linux kernel
and the hardware chip and fits the TPM-specific interfaces created by IBM in
drivers/char/tpm/tpm.h
Further information about this module and a list of succesfully tested and
therefore supported hardware can be found at our project page [3].
[1]
http://www.infineon.com/cgi/ecrm.dll/ecrm/scripts/public_download.jsp?oid=114135&parent_oid=29049
[2]
http://www.tonymcfadden.net/tpmvendors.htm
[3]
http://www.prosec.rub.de/tpm
Signed-off-by: Marcel Selhorst <selhorst@crypto.rub.de>
Acked-by: Kylene Jo Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
|
