| Age | Commit message (Collapse) | Author |
|---|
|
Using PWRSTS_RET on msm8974's MDSS_GDSC causes display to stop working.
The gdsc doesn't fully come out of retention mode. Change it's pwrsts
flags to PWRSTS_OFF_ON.
Fixes: d399723950c4 ("clk: qcom: gdsc: Fix the handling of PWRSTS_RET support")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Link: https://lore.kernel.org/r/20230507175335.2321503-2-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The mdp_clk_src clock should not be turned off. Instead it should be
'parked' to the XO, as most of other mdp_clk_src clocks. Fix that by
using the clk_rcg2_shared_ops.
Fixes: d8b212014e69 ("clk: qcom: Add support for MSM8974's multimedia clock controller (MMCC)")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230507175335.2321503-1-dmitry.baryshkov@linaro.org
|
|
After the internal discussions, it looks like this clock is managed by
RPM itself. Linux kernel should not touch it on its own, as this causes
disagreement with RPM. Shutting down this clock causes the OCMEM<->GPU
interface to stop working, resulting in GPU hangchecks/timeouts.
Fixes: d8b212014e69 ("clk: qcom: Add support for MSM8974's multimedia clock controller (MMCC)")
Suggested-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230508153319.2371645-1-dmitry.baryshkov@linaro.org
|
|
Convert the clock driver to specify parent data rather than parent
names, to actually bind using 'clock-names' specified in the DTS rather
than global clock names. Use parent_hws where possible to refer parent
clocks directly, skipping the lookup.
Note, the system names for xo clocks were changed from "xo" to
"xo_board" to follow the example of other platforms. This switches the
clocks to use DT-provided "xo_board" clock instead of manually
registered "xo" clock and allows us to drop qcom_cc_register_board_clk()
call from the driver at some point.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221204124508.1415713-9-dmitry.baryshkov@linaro.org
|
|
Move clock parent tables down, after the PLL declarataions, so that we
can use pll hw clock fields in the next commit.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221204124508.1415713-8-dmitry.baryshkov@linaro.org
|
|
Use ARRAY_SIZE() instead of manually specifying num_parents. This makes
adding/removing entries to/from parent_data easy and errorproof.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221204124508.1415713-7-dmitry.baryshkov@linaro.org
|
|
Modify the existing MSM8974 multimedia clock controller driver to
support the MMCC found on MSM8226 based devices. This should allow most
multimedia device drivers to probe and control their clocks.
Signed-off-by: Bartosz Dudziak <bartosz.dudziak@snejp.pl>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220207185411.19118-3-bartosz.dudziak@snejp.pl
|
|
'mmcc_xo_mmpll0_1_2_gpll0{map}'
Fixes the following W=1 kernel build warning(s):
drivers/clk/qcom/mmcc-msm8974.c:85:27: warning: ‘mmcc_xo_mmpll0_1_2_gpll0’ defined but not used [-Wunused-const-variable=]
drivers/clk/qcom/mmcc-msm8974.c:77:32: warning: ‘mmcc_xo_mmpll0_1_2_gpll0_map’ defined but not used [-Wunused-const-variable=]
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210126124540.3320214-17-lee.jones@linaro.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
gfx3d_clk_src for msm8974 was introduced into the MMCC by
commit d8b212014e69 ("clk: qcom: Add support for MSM8974's multimedia
clock controller (MMCC)") to ensure that all of the clocks for
this platform are documented upstream. This clock actually belongs
on the RPM. Since then, commit 685dc94b7d8f ("clk: qcom: smd-rpmcc:
Add msm8974 clocks") was introduced, which contains the proper
definition for gfx3d_clk_src. Let's drop the definition from the
mmcc and register the clock with the rpm instead.
This change was tested on a Nexus 5 (hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Link: https://lkml.kernel.org/r/20191115123931.18919-1-masneyb@onstation.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Based on 1 normalized pattern(s):
this software is licensed under the terms of the gnu general public
license version 2 as published by the free software foundation and
may be copied distributed and modified under those terms this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 285 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.642774971@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Frequency table macro is used by multiple clock drivers, move frequency
table macro to common header file.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
* clk-fixes:
clk: gpio: Really allow an optional clock= DT property
Revert "clk: qcom: Specify LE device endianness"
|
|
This reverts commit 329cabcecf94d8d7821e729dda284ba9dec44c87.
The commit that caused us to specify LE device endianness here,
29bb45f25ff3 (regmap-mmio: Use native endianness for read/write,
2015-10-29), has been reverted in mainline so now when we specify
LE it actively breaks big endian kernels because the byte
swapping in regmap-mmio is incorrect. Let's revert this change
because it will 1) fix the big endian kernels and 2) be redundant
to specify LE because that will become the default soon.
Cc: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
With gdsc driver capable of handling hierarchical power domains,
specify oxili_gdsc as parent of oxilicx_gdsc.
Remove all direct calls to genpd from the mmcc clock driver. The
adding and removing of subdomains is now handled from within
the gdsc driver.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
All these clock controllers are little endian devices, but so far
we've been relying on the regmap mmio bus handling this for us
without explicitly stating that fact. After commit 4a98da2164cf
(regmap-mmio: Use native endianness for read/write, 2015-10-29),
the regmap mmio bus will read/write with the __raw_*() IO
accessors, instead of using the readl/writel() APIs that do
proper byte swapping for little endian devices.
So if we're running on a big endian processor and haven't
specified the endianness explicitly in the regmap config or in
DT, we're going to switch from doing little endian byte swapping
to big endian accesses without byte swapping, leading to some
confusing results. On my apq8074 dragonboard, this causes the
device to fail to boot as we access the clock controller with
big endian IO accesses even though the device is little endian.
Specify the endianness explicitly so that the regmap core
properly byte swaps the accesses for us.
Reported-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Tyler Baker <tyler.baker@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Cc: Simon Arlott <simon@fire.lp0.eu>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Now that qcom_cc_remove() is a nop, drop calls to
qcom_cc_remove() and any empty driver remove functions.
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
The oxili_cx GDSC is inside the power domain of the oxili GDSC.
Add the dependency so that the CX domain can properly power up.
Reported-by: Rob Clark <robdclark@gmail.com>
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Add the GDSC instances that exist as part of msm8974 MMCC block
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Sometimes the display driver may want to change the parent PLL of
the display clocks (byte and pixel clocks) depending on the
use-case. Currently the parent is fixed by means of having a
frequency table with one entry that chooses a particular parent.
Remove this restriction and use the parent the clock is
configured for in the hardware during clk_set_rate(). This
requires consumers to rely on the default parent or to configure
the parent with clk_set_parent()/assigned-clock-parents on the
clocks before calling clk_set_rate().
Tested-by: Archit Taneja <architt@codeaurora.org>
Cc: Hai Li <hali@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Make const both the array and the strings, so they can be
moved to .rodata section.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
In the current parent mapping code, we can get duplicate or inconsistent
indexes, which leads to discrepancy between the number of elements in the
array and the number of parents. Until now, this was solved with some
reordering but this is not always possible.
This patch introduces index tables that are used to define the relations
between the PLL source and the hardware mux configuration value.
To accomplish this, here we do the following:
- Define a parent_map struct to map the relations between PLL source index
and register configuration value.
- Add a qcom_find_src_index() function for finding the index of a clock
matching the specific PLL configuration.
- Update the {set,get}_parent RCG functions use the newly introduced
parent_map struct.
- Convert all existing drivers to the new parent_map tables.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
There is no need to init .owner field.
Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Sometimes we need to program PLLs with a fixed rate
configuration during driver probe. Doing this after we register
the PLLs with the clock framework causes the common clock
framework to assume the rate of the PLLs are 0. This causes all
sorts of problems for rate recalculations because the common
clock framework caches the rate once at registration time unless
a flag is set to always recalculate the rates.
Split the qcom_cc_probe() function into two pieces, map and
everything else, so that drivers which need to configure some
PLL rates or otherwise twiddle bits in the clock controller can
do so before registering clocks. This allows us to properly
detect the rates of PLLs that are programmed at boot.
Fixes: 49fc825f0cc2 "clk: qcom: Consolidate common probe code"
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
The display clocks all source from dedicated phy PLLs within their
respective multimedia hardware block. Hook up these PLLs to the
display clocks with the appropriate parent mappings, clock flags,
and the appropriate clock ops. This should allow the display
clocks to work once the appropriate phy PLL driver registers their
PLL clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
We forgot to add the status bit for the PLLs and we were using
the wrong register and masks for configuration, leading to
unexpected PLL configurations. Fix this.
Fixes: d8b212014e69 (clk: qcom: Add support for MSM8974's multimedia clock controller (MMCC))
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Most of the probe code is the same between all the different
clock controllers. Consolidate the code into a common.c file.
This makes changes to the common probe parts easier and reduces
chances for bugs.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Add a driver for the global clock controller found on MSM 8974
based platforms. This should allow most multimedia device drivers
to probe and control their clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
