| Age | Commit message (Collapse) | Author |
|---|
|
git://git.linaro.org/people/mike.turquette/linux
Pull clk framework changes from Mike Turquette:
"The first half of the clk framework pull request is made up almost
entirely of new platform/driver support. There are some conversions
of existing drivers to the common-clock Device Tree binding, and a few
non-critical fixes to the framework.
Due to an entirely unnecessary cyclical dependency with the arm-soc
tree this pull request is broken into two pieces. The second piece
will be sent out after arm-soc sends you the pull request that merged
in core support for the HiSilicon 3620 platform. That same pull
request from arm-soc depends on this pull request to merge in those
HiSilicon bits without causing build failures"
[ Just did the ARM SoC merges, so getting ready for the second clk tree
pull request - Linus ]
* tag 'clk-for-linus-3.14-part1' of git://git.linaro.org/people/mike.turquette/linux: (97 commits)
devicetree: bindings: Document qcom,mmcc
devicetree: bindings: Document qcom,gcc
clk: qcom: Add support for MSM8660's global clock controller (GCC)
clk: qcom: Add support for MSM8974's multimedia clock controller (MMCC)
clk: qcom: Add support for MSM8974's global clock controller (GCC)
clk: qcom: Add support for MSM8960's multimedia clock controller (MMCC)
clk: qcom: Add support for MSM8960's global clock controller (GCC)
clk: qcom: Add reset controller support
clk: qcom: Add support for branches/gate clocks
clk: qcom: Add support for root clock generators (RCGs)
clk: qcom: Add support for phase locked loops (PLLs)
clk: qcom: Add a regmap type clock struct
clk: Add set_rate_and_parent() op
reset: Silence warning in reset-controller.h
clk: sirf: re-arch to make the codes support both prima2 and atlas6
clk: composite: pass mux_hw into determine_rate
clk: shmobile: Fix MSTP clock array initialization
clk: shmobile: Fix MSTP clock index
ARM: dts: Add clock provider specific properties to max77686 node
clk: max77686: Register OF clock provider
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM driver updates from Olof Johansson:
"Updates of SoC-near drivers and other driver updates that makes more
sense to take through our tree.
The largest part of this is a conversion of device registration for
some renesas shmobile/sh devices over to use resources. This has
required coordination with the corresponding arch/sh changes, and
we've agreed to merge the arch/sh changes through our tree.
Added in this branch is support for Trusted Foundations secure
firmware, which is what is used on many of the commercial Nvidia Tegra
products that are in the market, including the Nvidia Shield. The
code is local to arch/arm at this time since it's uncertain whether it
will be shared with arm64 longer-term, if needed we will refactor
later.
A couple of new RTC drivers used on ARM boards, merged through our
tree on request by the RTC maintainer.
... plus a bunch of smaller updates across the board, gpio conversions
for davinci, etc"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (45 commits)
watchdog: davinci: rename platform driver to davinci-wdt
tty: serial: Limit msm_serial_hs driver to platforms that use it
mmc: msm_sdcc: Limit driver to platforms that use it
usb: phy: msm: Move mach dependent code to platform data
clk: versatile: fixup IM-PD1 clock implementation
clk: versatile: pass a name to ICST clock provider
ARM: integrator: pass parent IRQ to the SIC
irqchip: versatile FPGA: support cascaded interrupts from DT
gpio: davinci: don't create irq_domain in case of unbanked irqs
gpio: davinci: use chained_irq_enter/chained_irq_exit API
gpio: davinci: add OF support
gpio: davinci: remove unused variable intc_irq_num
gpio: davinci: convert to use irqdomain support.
gpio: introduce GPIO_DAVINCI kconfig option
gpio: davinci: get rid of DAVINCI_N_GPIO
gpio: davinci: use {readl|writel}_relaxed() instead of __raw_*
serial: sh-sci: Add OF support
serial: sh-sci: Add device tree bindings documentation
serial: sh-sci: Remove platform data mapbase and irqs fields
serial: sh-sci: Remove platform data scbrr_algo_id field
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"DT and DT-conversion-related changes for various ARM platforms. Most
of these are to enable various devices on various boards, etc, and not
necessarily worth enumerating.
New boards and systems continue to come in as new devicetree files
that don't require corresponding C changes any more, which is
indicating that the system is starting to work fairly well.
A few things worth pointing out:
* ST Ericsson ux500 platforms have made the major push to move over
to fully support the platform with DT
* Renesas platforms continue their conversion over from legacy
platform devices to DT-based for hardware description"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (327 commits)
ARM: dts: SiRF: add pin group for USP0 with only RX or TX frame sync
ARM: dts: SiRF: add lost usp1_uart_nostreamctrl pin group for atlas6
ARM: dts: sirf: add lost minigpsrtc device node
ARM: dts: sirf: add clock, frequence-voltage table for CPU0
ARM: dts: sirf: add lost bus_width, clock and status for sdhci
ARM: dts: sirf: add lost clocks for cphifbg
ARM: dts: socfpga: add pl330 clock
ARM: dts: socfpga: update L2 tag and data latency
arm: sun7i: cubietruck: Enable the i2c controllers
ARM: dts: add support for EXYNOS4412 based TINY4412 board
ARM: dts: Add initial support for Arndale Octa board
ARM: bcm2835: add USB controller to device tree
ARM: dts: MSM8974: Add MMIO architected timer node
ARM: dts: MSM8974: Add restart node
ARM: dts: sun7i: external clock outputs
ARM: dts: sun7i: Change 32768 Hz oscillator node name to clk@N style
ARM: dts: sun7i: Add pin muxing options for clock outputs
ARM: dts: sun7i: Add rtp controller node
ARM: dts: sun5i: Add rtp controller node
ARM: dts: sun4i: Add rtp controller node
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep
it strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared
with Mike Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for
multiplatform"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: mvebu: move Armada 370/XP specific definitions to armada-370-xp.h
ARM: mvebu: remove prototypes of non-existing functions from common.h
ARM: mvebu: move ARMADA_XP_MAX_CPUS to armada-370-xp.h
serial: sh-sci: Rework baud rate calculation
serial: sh-sci: Compute overrun_bit without using baud rate algo
serial: sh-sci: Remove unused GPIO request code
serial: sh-sci: Move overrun_bit and error_mask fields out of pdata
serial: sh-sci: Support resources passed through platform resources
serial: sh-sci: Don't check IRQ in verify port operation
serial: sh-sci: Set the UPF_FIXED_PORT flag
serial: sh-sci: Remove duplicate interrupt check in verify port op
serial: sh-sci: Simplify baud rate calculation algorithms
serial: sh-sci: Remove baud rate calculation algorithm 5
serial: sh-sci: Sort headers alphabetically
ARM: EXYNOS: Kill exynos_pm_late_initcall()
ARM: EXYNOS: Consolidate selection of PM_GENERIC_DOMAINS for Exynos4
ARM: at91: switch Calao QIL-A9260 board to DT
clk: at91: fix pmc_clk_ids data type attriubte
PM / devfreq: use inclusion <mach/map.h> instead of <plat/map-s5p.h>
ARM: EXYNOS: remove <mach/regs-clock.h> for exynos
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-critical fixes from Olof Johansson:
"As usual, we have a batch of fixes that weren't considered significant
enough to warrant going into the later -rcs for previous release, so
they are queued up on this branch.
A handful of these are for various DT fixups for Samsung platforms,
and a handful of other minor things.
There are also a couple of stable-marked patches for mvebu -- they
came in quite late and we decided to keep them deferred until the
first -stable release to get more coverage instead of squeezing them
into 3.13"
* tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (32 commits)
ARM: at91: smc: bug fix in sam9_smc_cs_read()
i2c: mv64xxx: Document the newly introduced Armada XP A0 compatible
i2c: mv64xxx: Fix bus hang on A0 version of the Armada XP SoCs
ARM: mvebu: Add quirk for i2c for the OpenBlocks AX3-4 board
ARM: mvebu: Add support to get the ID and the revision of a SoC
ARM: dts: msm: Fix gpio interrupt and reg length
irqchip: sirf: set IRQ_LEVEL status_flags
ARM: OMAP2+: gpmc: Move legacy GPMC width setting
ARM: OMAP2+: gpmc: Introduce gpmc_set_legacy()
ARM: OMAP2+: gpmc: Move initialization outside the gpmc_t condition
ARM: OMAP2+: board-generic: update SoC compatibility strings
Documentation: dt: OMAP: explicitly state SoC compatible strings
ARM: OMAP2+: enable AM33xx SOC EVM audio
ARM: OMAP2+: Select USB PHY for AM335x SoC
ARM: bcm2835: Fix grammar in help message
ARM: msm: trout: fix uninit var warning
ARM: dts: Use MSHC controller for eMMC memory for exynos4412-trats2
ARM: dts: Fix definition of MSHC device tree nodes for exynos4x12
ARM: dts: add clock provider for mshc node for Exynos4412 SOC
clk: samsung: exynos4: Fix definition of div_mmc_pre4 divider
...
|
|
|
|
Add a driver for the global clock controller found on MSM8660
based platforms. This should allow most non-multimedia device
drivers to probe and control their clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Add a driver for the global clock controller found on MSM 8974
based platforms. This should allow most multimedia device drivers
to probe and control their clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Add a driver for the global clock controller found on MSM 8974
based platforms. This should allow most non-multimedia device
drivers to probe and control their clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Add a driver for the multimedia clock controller found on MSM
8960 based platforms. This should allow multimedia device drivers
to probe and control their clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Add a driver for the global clock controller found on MSM8960
based platforms. This should allow most non-multimedia device
drivers to probe and control their clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Reset controllers and clock controllers are combined into one IP
block on Qualcomm chipsets. Usually a reset signal is associated
with each clock branch but sometimes a reset signal is associated
with a handful of clocks. Either way the register interface is
the same; set a bit to assert a reset and clear a bit to deassert
a reset. Add support for these types of resets signals.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Add support for the root clock generators on Qualcomm devices.
RCGs are highly customizable mux/divider/counter clocks that can
be used to generate almost any rate desired given some input
source that is faster than the desired rate.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Add support for Qualcomm's PLLs (phase locked loops). This is
sufficient enough to be able to determine the rate the PLL is
running at. We can add rate setting support later when it's
needed.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Add a clock type that associates a regmap pointer and some
enable/disable bits with a clk_hw struct. This will be the struct
that a hw specific implementation wraps if it wants to use the
regmap helper functions.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Some of Qualcomm's clocks can change their parent and rate at the
same time with a single register write. Add support for this
hardware to the common clock framework by adding a new
set_rate_and_parent() op. When the clock framework determines
that both the parent and the rate are going to change during
clk_set_rate() it will call the .set_rate_and_parent() op if
available and fall back to calling .set_parent() followed by
.set_rate() otherwise.
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
sirfprima2 and sirfatlas6 are two different SoCs in CSR SiRF series. for
prima2 and atlas6, there are many shared clocks but there are still
some different register layout and hardware clocks, then result in
different clock table.
here we re-arch the driver to
1. clk-common.c provides common clocks for prima2 and atlas6,
2. clk-prima2.h describles registers of prima2 and clk-prima2.c provides
prima2 specific clocks and clock table.
3. clk-atlas6.h describles registers of atlas6 and clk-atlas6.c provides
atlas6 specific clocks and clock table.
4. clk.h and clk.c expose external interfaces and provide uniform entry
for both prima2 and atlas6.
so both prima2 and atlas6 will get support by drivers/clk/sirf.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Rongjun Ying <Rongjun.Ying@csr.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
The composite clock's .determine_rate implementation can call the
underyling .determine_rate callback corresponding to rate_hw or the
underlying .determine_rate callback corresponding to mux_hw. In both
cases we pass in rate_hw, which is wrong. Fixed by passing mux_hw into
the correct callback.
Reported-by: Lemon Dai <dailemon.gl@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
next/cleanup
From Nicolas Ferre:
Second cleanup pull-request for 3.14:
- a tiny fix for the recent AT91 CCF implementation
- the switch of one platform to DT with board file removal
* tag 'at91-cleanup2' of git://github.com/at91linux/linux-at91:
ARM: at91: switch Calao QIL-A9260 board to DT
clk: at91: fix pmc_clk_ids data type attriubte
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/fixes-non-critical
From Tony Lindgren:
Some non-urgent fixes to enable am335x features, update documentation,
and to remove unnecessary double initialization for the GPMC code.
* tag 'omap-for-v3.14/fixes-not-urgent-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (238 commits)
ARM: OMAP2+: gpmc: Move legacy GPMC width setting
ARM: OMAP2+: gpmc: Introduce gpmc_set_legacy()
ARM: OMAP2+: gpmc: Move initialization outside the gpmc_t condition
ARM: OMAP2+: board-generic: update SoC compatibility strings
Documentation: dt: OMAP: explicitly state SoC compatible strings
ARM: OMAP2+: enable AM33xx SOC EVM audio
ARM: OMAP2+: Select USB PHY for AM335x SoC
+Linux 3.13-rc5
|
|
|
|
The clks member of the clk_onecell_data structure should
point to a valid clk array (no NULL entries allowed),
and the clk_num should be equal to the number
of elements in the clks array.
The MSTP driver fails to satisfy the above conditions.
The clks array may contain NULL entries if not all
clock-indices are initialized in the device tree.
Thus, if the clock indices are interleaved we end up
with NULL pointers in-between.
The other problem is the driver uses maximum clock index
as the number of clocks, which is incorrect (less than
the actual number of clocks by 1).
Fix the first issue by pre-setting the whole clks array
with ERR_PTR(-ENOENT) pointers instead of zeros; and
use maximum clkidx + 1 as the number of clocks to fix
the other one.
This should make of_clk_src_onecell_get() return the following:
* valid clk pointers for all clocks registered;
* ERR_PTR(-EINVAL) if (idx >= clk_data->clk_num);
* ERR_PTR(-ENOENT) if the clock at the selected index was not
initialized in the device tree (and was not registered).
Changes in V2:
* removed brackets from the one-line for loop
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Use clkidx when registering MSTP clocks instead of loop counter
since the value is then used to access the specific clock index bit
in the mstp register.
The issue was introduced by the following commit:
f94859c215b6d977 "clk: shmobile: Add MSTP clock support"
Changes in V2:
* none
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tfiga/samsung-clk into clk-next-samsung
(A bit late) first round of Samsung clock patches for v3.14.
|
|
If max77686 chip is instantiated from device tree, it is desirable to
have an OF clock provider to allow device tree based look-up of clocks.
This patch adds OF clock provider registration to the clk-max77686
driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
As a prerequisite for further patch adding OF clock provider support to
the driver, this patch changes the driver to store an array of struct
clk * as driver data.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
This patch fixes invalid kfree() and adds missing call to clk_unregister()
in error and remove paths in max77686_clk_probe(). While at it, error
handling is also cleaned up.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
As a preparation for further patches, this patch modifies the clock
registration helper function to return a pointer to the newly registered
clock. No functional change is done to the driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
The function can simply return 0, without jumping to a separate label,
which does exactly the same. This patch does not introduce any
functional change, just a clean-up.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
It is usually nice to know frequency of a clock, so this patch adds a
.recalc_rate() callback returning rates of provided clocks.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Changing status of clock gates in max77686 requires i2c transfers, which
can sleep, so this is done in prepare and unprepare callbacks. Due to
this, checking whether whether the clock is ungated must be done
in is_prepared() callback as well, for consistency.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
The AudioSS block on Exynos 5420 has an additional clock gate for the
ADMA bus clock.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
|
|
There is no gate for the PCM clock input to the AudioSS block, so
the parent of sclk_pcm is div_pcm0. Add a clock ID for it so that
we can reference it in device trees.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
|
|
This allows the input clocks to the Exynos AudioSS block to be
specified via device-tree bindings. Default names will be used
when an input clock is not given.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
|
|
The Exynos AudioSS clock controller will later be modified to allow
input clocks to be specified via device-tree in order to support
multiple Exynos SoCs. This will introduce a dependency on the core
SoC clock controller being initialized first so that the AudioSS driver
can look up its input clocks, but the order in which clock providers
are probed in of_clk_init() is not guaranteed. Since deferred probing
is not supported in of_clk_init() and the AudioSS block is not the core
controller, we can initialize it later as a platform device.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
|
|
The patch replaces private enum clock IDs in the driver with macros provided
by the DT header.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
|
|
The patch replaces private enum clock IDs in the driver with macros provided
by the DT header.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
|
|
The patch replaces private enum clock IDs in the driver with macros provided
by the DT header.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
|
|
The patch replaces private enum clock IDs in the driver with macros provided
by the DT header.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
|
|
Register the APLL rate table so that we can set the APLL rate from
the cpufreq driver.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
|
|
Commit 6d9252bd9a4bb (clk: Add support for power of two type dividers)
merged in v3.6 added the _get_val function to convert a divisor value to
a register field value depending on the flags. However it used the type
u8 for the div field, causing divisors larger than 255 to be masked
and the resultant clock rate to be too high.
E.g. in my case an 11bit divider was supposed to divide 24.576 MHz down
to 32.768KHz. The divisor was correctly calculated as 750 (0x2ee). This
was masked to 238 (0xee) resulting in a frequency of 103.26KHz.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: stable@vger.kernel.org
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tfiga/samsung-clk into clk-fixes
Samsung Clock fixes for 3.13-rc7
* Several patches fixing up incorrectly defined register addresses and
bitfield offsets that could lead to undefined operation when accessing
respective registers or bitfields.
1) clk: exynos5250: fix sysmmu_mfc{l,r} gate clocks
2a) clk: samsung: exynos5250: Fix ACP gate register offset
2b) clk: samsung: exynos5250: Add MDMA0 clocks
2c) ARM: dts: exynos5250: Fix MDMA0 clock number
3) clk: samsung: exynos4: Correct SRC_MFC register
All three issues have been present since Exynos5250 and Exynos4 clock
drivers were added by commits 6e3ad26816b72 ("clk: exynos5250:
register clocks using common clock framework") and e062b571777f5
("clk: exynos4: register clocks using common clock framework")
respectively.
* Patch to fix automatic disabling of Exynos5250 sysreg clock that could
cause undefined operation of several peripherals, such as USB, I2C,
MIPI or display block.
4) clk: samsung: exynos5250: Add CLK_IGNORE_UNUSED flag for the sysreg
clock
Present since Exynos5250 clock drivers was added by commits
6e3ad26816b72 ("clk: exynos5250: register clocks using common clock
framework").
* Patch fixing compilation warning in clk-exynos-audss driver when
CONFIG_PM_SLEEP is disabled.
5) clk: exynos: File scope reg_save array should depend on PM_SLEEP
Present since the driver was added by commit 1241ef94ccc3 ("clk:
samsung: register audio subsystem clocks using common clock
framework").
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/drivers
From Linus Walleij:
Some Integrator patches that matured for v3.14:
- Use PATCH_PHYS_TO_VIRT and AUTO_ZRELADDR.
- Support cascaded interrupts on the SIC.
- Complete clock implementation for the IM-PD1.
* tag 'integrator-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
clk: versatile: fixup IM-PD1 clock implementation
clk: versatile: pass a name to ICST clock provider
ARM: integrator: pass parent IRQ to the SIC
irqchip: versatile FPGA: support cascaded interrupts from DT
ARM: integrator: Default enable ARM_PATCH_PHYS_VIRT, AUTO_ZRELADDR
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
From Simon Horman:
Third Round of Renesas ARM Based SoC DT Updates for v3.14
* r8a7791 (R-Car M2) and r8a7790 (R-Car H2) SoCSs
- Add SSI, QSPI and MSIOF clocks in device tree
r8a7791 (R-Car M2) based Koelsch and r8a7790 (R-Car H2) based Lager boards
- Remove reference DTS
- Specify external clock frequency in DT
- Sync non-reference DTS with referene DTS
- Add clocks to DTS
* r8a7740 (R-Mobile A1) based Armadillo board
- Add gpio-keys device
- Add PWM backlight enable GPIO
- Add PWM backlight power supply
* r8a73a0 (SH-Mobile AG5), r8a7740 (R-Mobile A1) and
r8a73a4 (SH-Mobile APE6) SoCs
- Specify PFC interrupts in DT
* tag 'renesas-dt3-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (72 commits)
ARM: shmobile: r8a7791: Add SSI clocks in device tree
ARM: shmobile: r8a7790: Add SSI clocks in device tree
ARM: shmobile: r8a7791: Add QSPI module clock in device tree
ARM: shmobile: r8a7790: Add QSPI module clock in device tree
ARM: shmobile: r8a7791: Add MSIOF clocks in device tree
ARM: shmobile: r8a7790: Add MSIOF clocks in device tree
ARM: shmobile: Remove Koelsch reference DTS
ARM: shmobile: Remove Lager reference DTS
ARM: shmobile: koelsch: Specify external clock frequency in DT
ARM: shmobile: lager: Specify external clock frequency in DT
ARM: shmobile: Sync Koelsch DTS with Koelsch reference DTS
ARM: shmobile: Sync Lager DTS with Lager reference DTS
ARM: shmobile: r8a7791: Add clocks
ARM: shmobile: r8a7790: Reference clocks
ARM: shmobile: r8a7790: Add clocks
ARM: shmobile: armadillo: dts: Add gpio-keys device
ARM: shmobile: sh73a0: Specify PFC interrupts in DT
ARM: shmobile: r8a7740: Specify PFC interrupts in DT
ARM: shmobile: r8a73a4: Specify PFC interrupts in DT
ARM: shmobile: armadillo: dts: Add PWM backlight enable GPIO
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Register both VCO clocks, give per-logical module unique names
to the clocks so we can have several IM-PD1's connected (in
theory). Implement all the fixed-factor clocks as children of
VCO2.
Tested by using the UARTs and the PL181 MMC block on the IM-PD1,
works flawlessly.
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When we have more than one of these clocks in a system (such as
on the IM-PD1) we need a mechanism to pass a name for the clock.
Refactor to add this as an argument.
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
'asoc/topic/adav80x', 'asoc/topic/adsp', 'asoc/topic/ak4641', 'asoc/topic/ak4642', 'asoc/topic/arizona', 'asoc/topic/atmel', 'asoc/topic/au1x', 'asoc/topic/axi', 'asoc/topic/bcm2835', 'asoc/topic/blackfin', 'asoc/topic/cs4271', 'asoc/topic/cs42l52', 'asoc/topic/da7210', 'asoc/topic/davinci', 'asoc/topic/ep93xx', 'asoc/topic/fsl', 'asoc/topic/fsl-mxs', 'asoc/topic/generic', 'asoc/topic/hdmi', 'asoc/topic/jack', 'asoc/topic/jz4740', 'asoc/topic/max98090', 'asoc/topic/mxs', 'asoc/topic/omap', 'asoc/topic/pxa', 'asoc/topic/rcar', 'asoc/topic/s6000', 'asoc/topic/sai', 'asoc/topic/samsung', 'asoc/topic/sgtl5000', 'asoc/topic/spear', 'asoc/topic/ssm2518', 'asoc/topic/ssm2602', 'asoc/topic/tegra', 'asoc/topic/tlv320aic3x', 'asoc/topic/twl6040', 'asoc/topic/txx9', 'asoc/topic/uda1380', 'asoc/topic/width', 'asoc/topic/wm8510', 'asoc/topic/wm8523', 'asoc/topic/wm8580', 'asoc/topic/wm8711', 'asoc/topic/wm8728', 'asoc/topic/wm8731', 'asoc/topic/wm8741', 'asoc/topic/wm8750', 'asoc/topic/wm8753', 'asoc/topic/wm8776', 'asoc/topic/wm8804', 'asoc/topic/wm8900', 'asoc/topic/wm8901', 'asoc/topic/wm8940', 'asoc/topic/wm8962', 'asoc/topic/wm8974', 'asoc/topic/wm8985', 'asoc/topic/wm8988', 'asoc/topic/wm8990', 'asoc/topic/wm8991', 'asoc/topic/wm8994', 'asoc/topic/wm8995', 'asoc/topic/wm9081' and 'asoc/topic/x86' into asoc-next
|
|
Conflicts:
drivers/clk/clk.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into clk-next-keystone
|
