| Age | Commit message (Collapse) | Author |
|---|
|
With the Silicon revision being taken directly from socinfo, there's no
longer any need for reading any SOC register for revision from this driver.
Hence, we do not require any rev_offset for AM62 family of devices.
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The AM625 syscon for efuse was being taken earlier from the wkup_conf node
where the entire wkup_conf was marked as "syscon". This is wrong and will
be fixed in the devicetree. However, whenever that does happen will end up
breaking this driver for that device because of the change in efuse offset.
Hence, to avoid breaking any sort of backward compatibility of devicetrees
use a quirk to distinguish and accordingly use 0x0 offset for the new
syscon node.
Suggested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
In the AM62x, AM62Ax, and AM62Px devices, we already have the revision
info within the k3-socinfo driver. Hence, re-use this information from
there instead of re using the offset for 2 drivers trying to get the
same information ie. revision.
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Commit b4bc9f9e27ed ("cpufreq: ti-cpufreq: add support for omap34xx
and omap36xx") introduced special handling for OMAP3 class devices
where syscon node may not be present. However, this also creates a bug
where the syscon node is present, however the offset used to read
is beyond the syscon defined range.
Fix this by providing a quirk option that is populated when such
special handling is required. This allows proper failure for all other
platforms when the syscon node and efuse offsets are mismatched.
Fixes: b4bc9f9e27ed ("cpufreq: ti-cpufreq: add support for omap34xx and omap36xx")
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
!CONFIG_OF builds cause warnings on unused of_device_id tables. This is
due to of_match_node() being a macro rather than static inline function.
Add a __maybe_unused annotation to the of_device_id tables.
Fixes: c7582ec85342 ("cpufreq: Drop CONFIG_ARM and CONFIG_ARM64 dependency on Arm drivers")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202408090714.wcrqU6Pk-lkp@intel.com/
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
More speed grades for the AM62Px SoC family have been defined which
unfortunately no longer align with the AM62x table. So create a new
table with these new speed grades defined for the AM62Px
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
As the AM62Ax SoC family matures more speed grades are being defined.
These new grades unfortunately no longer align with the AM62x SoC
family. Define a new table with new OPP speed grade limits for the
AM62Ax
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Handle deferred probing gracefully by using dev_err_probe() to not
spam console with unnecessary error messages.
Fixes: f88d152dc739 ("cpufreq: ti: Migrate to dev_pm_opp_set_config()")
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Modify the ti_cpufreq_match_node() function to utilize the __free()
cleanup handler for automatically releasing the device node when it goes
out of scope.
By moving the declaration to the initialization, the patch ensures that
the device node is properly managed throughout the function's scope,
thus eliminating the need for manual invocation of of_node_put().
This approach reduces the potential for memory leaks.
Suggested-by: Julia Lawall <julia.lawall@inria.fr>
Signed-off-by: Shivani Gupta <shivani07g@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The am62p5 is a variation of the am625 and the am62a7 SoC families. Add
the am62p5 to the list using the same cpufreq data as the rest of the
am62x extended family.
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Add support for TI K3 AM62A7 SoC to read speed and revision values from
hardware and pass to OPP layer. AM62A7 has the same A53 and efuse
configuration as AM625. Thus, soc_data from AM625 is reused.
Based on AM625 CPUFreq patch series by Dave Gerlach.
Signed-off-by: Vibhore Vardhan <vibhore@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Add support for TI K3 AM625 SoC to read speed and revision values from
hardware and pass to OPP layer.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Vibhore Vardhan <vibhore@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Add missing __init annotation to module init funcs.
Signed-off-by: Xiu Jianfeng <xiujianfeng@huawei.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The OPP core now provides a unified API for setting all configuration
types, i.e. dev_pm_opp_set_config().
Lets start using it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Make dev_pm_opp_set_regulators() accept a NULL terminated list of names
instead of making the callers keep the two parameters in sync, which
creates an opportunity for bugs to get in.
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Steven Price <steven.price@arm.com> # panfrost
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
|
|
DRA762 SoC introduces OPP_PLUS which runs at 1.8GHz. Add
support for this OPP in ti-cpufreq driver.
Acked-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The AM3517 only lists 600MHz @ 1.2V, but the register values for
0x4830A204 = 1b86 802f, it seems like am3517 might be a derivative
of the omap36 which OPPs would be OPP50 (300 MHz) and OPP100
(600 MHz).
This patch simply adds the am3517 to the compatible table
similar to a mix of the omap3430 and omap3430 structure.
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
See DM3730,DM275 data sheet (SPRS685B) footnote (6) in Table 4-19
which says that ABB must be switched to FBB mode when using the
OPP1G.
The LOD definition abb_mpu_iva already exists so that we need
to add plumbing for vbb-supply = <&abb_mpu_iva>
and define two voltage vectors for each OPP so that the abb LDO
is also updated by the ti-cpufreq driver.
We also must switch the ti_cpufreq_soc_data to multi_regulator.
Note: reading out the abb reglator voltage to verify that
it does do transitions can be done by
cat /sys/devices/platform/68000000.ocp/483072f0.regulator-abb-mpu/regulator/regulator.*/microvolts
Likewise, read the twl4030 provided VDD voltage by
cat /sys/devices/platform/68000000.ocp/48070000.i2c/i2c-0/0-0048/48070000.i2c:twl@48:regulator-vdd1/regulator/regulator.*/microvolts
Note: to check if the ABB FBB is enabled/disabled, check
registers
PRM_LDO_ABB_CTRL 0x483072F4 bit 3:0 1=bypass 5=FBB
PRM_LDO_ABB_SETUP 0x483072F0 0x00=bypass 0x11=FBB
e.g.
/dev/mem opened.
Memory mapped at address 0xb6fe4000.
Value at address 0x483072F4 (0xb6fe42f4): 0x3205
/dev/mem opened.
Memory mapped at address 0xb6f89000.
Value at address 0x483072F4 (0xb6f892f4): 0x3201
Note: omap34xx and am3517 have/need no comparable LDO
or mechanism.
Suggested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
In preparation for using the multi_regulator capability of
this driver for handling the ABB LDO for OPP1G of the omap36xx
we have to take care that the (legacy) vdd-supply name is
cpu0-supply = <&vcc>;
To do this we add another field to the SoC description table which
optionally can specify a list of regulator names.
For omap36xx we define "cpu0-supply" and "vbb-supply".
The default remains "vdd-supply" and "vbb-supply".
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
This adds code and tables to read the silicon revision and
eFuse (speed binned / 720 MHz grade) bits for selecting
opp-v2 table entries.
Since these bits are not always part of the syscon register
range (like for am33xx, am43, dra7), we add code to directly
read the register values using ioremap() if syscon access fails.
The format of the opp-supported-hw entries is that it has
two 32 bit bitfields. E.g.:
opp-supported-hw = <0xffffffff 3>
The first value is matched against the bit position of the
silicon revision which is (see TRM)
omap34xx:
BIT(0) ES1.0
BIT(1) ES2.0
BIT(2) ES2.1
BIT(3) ES3.0
BIT(4) ES3.1
BIT(7) ES3.1.2
omap36xx:
BIT(0) ES1.0
BIT(1) ES1.1
BIT(2) ES1.2
The second value is matched against the speed grade eFuse:
BIT(0) no high speed OPP
BIT(1) high speed OPP
This means for the example above that it is always enabled
while e.g.
opp-supported-hw = <0x1 2>
enables the OPP only for ES1.0 BIT(0) and if the high speed
eFuse is set BIT(1).
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Mark switch cases where we are expecting to fall through.
This patch fixes the following warning (Building: arm):
drivers/cpufreq/ti-cpufreq.c: In function ‘dra7_efuse_xlate’:
drivers/cpufreq/ti-cpufreq.c:79:20: warning: this statement may fall through [-Wimplicit-fallthrough=]
calculated_efuse |= DRA7_EFUSE_HIGH_MPU_OPP;
drivers/cpufreq/ti-cpufreq.c:80:2: note: here
case DRA7_EFUSE_HAS_OD_MPU_OPP:
^~~~
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently the ti-cpufreq driver blindly registers a 'ti-cpufreq' to force
the driver to probe on any platforms where the driver is built in.
However, this should only happen on platforms that actually can make use
of the driver. There is already functionality in place to match the
SoC compatible so let's factor this out into a separate call and
make sure we find a match before creating the ti-cpufreq platform device.
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The ti_cpufreq_probe() function uses regular kzalloc to allocate
the ti_cpufreq_data structure and kfree for freeing this memory
on failures. Simplify this code by using the devres managed
API.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Commit 05829d9431df (cpufreq: ti-cpufreq: kfree opp_data when
failure) has fixed a memory leak in the failure path, however
the patch returned a positive value on get_cpu_device() failure
instead of the previous negative value. Fix this incorrect error
return value properly.
Fixes: 05829d9431df (cpufreq: ti-cpufreq: kfree opp_data when failure)
Cc: 4.14+ <stable@vger.kernel.org> # v4.14+
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This driver can not be built as a module and there is no need of the
platform driver unregister part. Use builtin_platform_driver() instead
of module_platform_driver().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Some platforms, like those in the DRA7 and AM57 families, require the
scaling of multiple regulators in order to properly support higher OPPs.
Let the ti-cpufreq driver determine when this is required and pass the
appropriate regulator names to the OPP core so that they can be properly
managed.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ti-cpufreq will be responsible for calling dev_pm_opp_set_regulators on
platforms that require AVS and ABB regulator support so we must be
able to defer probe if regulators are not yet available, so change
ti-cpufreq to be a module_platform_driver to allow for probe defer.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
call of_node_put to release the refcount of np.
Signed-off-by: Zumeng Chen <zumeng.chen@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
memory leakage was found by kmemleak. opp_data needs to be freed
when failure, including fail_put_node.
unreferenced object 0xccdd4c40 (size 64):
comm "swapper", pid 1, jiffies 4294938465 (age 888.520s)
hex dump (first 32 bytes):
00 7c 00 c1 98 69 d8 ce 00 24 03 ce 00 24 03 ce .|...i...$...$..
20 35 23 c1 00 00 00 00 00 00 00 00 00 00 00 00 5#.............
backtrace:
[<c028fb64>] kmem_cache_alloc_trace+0x2c4/0x3cc
[<c076d5f0>] ti_cpufreq_probe+0x6c/0x334
[<c068d6e4>] platform_drv_probe+0x60/0xc0
[<c068b384>] driver_probe_device+0x218/0x2c4
[<c068b5a4>] __device_attach_driver+0xa8/0xdc
[<c0689340>] bus_for_each_drv+0x70/0xa4
[<c068b020>] __device_attach+0xc0/0x124
[<c068b634>] device_initial_probe+0x1c/0x20
[<c068a3b8>] bus_probe_device+0x94/0x9c
[<c0688300>] device_add+0x404/0x590
[<c068d408>] platform_device_add+0x11c/0x230
[<c068df40>] platform_device_register_full+0x10c/0x128
[<c076d578>] ti_cpufreq_init+0x44/0x50
[<c01017c4>] do_one_initcall+0x54/0x180
[<c0e00fe0>] kernel_init_freeable+0x270/0x33c
[<c093f2bc>] kernel_init+0x18/0x124
Signed-off-by: Zumeng Chen <zumeng.chen@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Rather than letting the ti-cpufreq driver match against 'ti,am4372'
machine compatible during probe let's match against 'ti,am43' so that we
can support both 'ti,am4372' and 'ti,am438x' platforms which both match
to this compatible.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
If 'dev_pm_opp_set_supported_hw()' fails, 'opp_data->opp_node' refcount
will be decremented 2 times.
One, just a few lines above, and another one in the error handling path.
Fix it by simply moving the 'of_node_put' call of the normal path.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The Kconfig currently controlling compilation of this code is:
drivers/cpufreq/Kconfig.arm:config ARM_TI_CPUFREQ
drivers/cpufreq/Kconfig.arm: bool "Texas Instruments CPUFreq support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Some TI SoCs, like those in the AM335x, AM437x, DRA7x, and AM57x families,
have different OPPs available for the MPU depending on which specific
variant of the SoC is in use. This can be determined through use of the
revision and an eFuse register present in the silicon. Introduce a
ti-cpufreq driver that can read the aformentioned values and provide
them as version matching data to the opp framework. Through this the
opp-supported-hw dt binding that is part of the operating-points-v2
table can be used to indicate availability of OPPs for each device.
This driver also creates the "cpufreq-dt" platform_device after passing
the version matching data to the OPP framework so that the cpufreq-dt
handles the actual cpufreq implementation. Even without the necessary
data to pass the version matching data the driver will still create this
device to maintain backwards compatibility with operating-points v1
tables.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
