| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"This contains driver changes that are tightly connected to SoC
specific code. Aside from smaller cleanups and bug fixes, here is a
list of the notable changes.
New device drivers:
- The Turris Mox router has a new "moxtet" bus driver for its
on-board pluggable extension bus. The same platform also gains a
firmware driver.
- The Samsung Exynos family gains a new Chipid driver exporting using
the soc device sysfs interface
- A similar socinfo driver for Qualcomm Snapdragon chips.
- A firmware driver for the NXP i.MX DSP IPC protocol using shared
memory and a mailbox
Other changes:
- The i.MX reset controller driver now supports the NXP i.MX8MM chip
- Amlogic SoC specific drivers gain support for the S905X3 and A311D
chips
- A rework of the TI Davinci framebuffer driver to allow important
cleanups in the platform code
- A couple of device drivers for removed ARM SoC platforms are
removed. Most of the removals were picked up by other maintainers,
this contains whatever was left"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (123 commits)
bus: uniphier-system-bus: use devm_platform_ioremap_resource()
soc: ti: ti_sci_pm_domains: Add support for exclusive and shared access
dt-bindings: ti_sci_pm_domains: Add support for exclusive and shared access
firmware: ti_sci: Allow for device shared and exclusive requests
bus: imx-weim: remove incorrect __init annotations
fbdev: remove w90x900/nuc900 platform drivers
spi: remove w90x900 driver
net: remove w90p910-ether driver
net: remove ks8695 driver
firmware: turris-mox-rwtm: Add sysfs documentation
firmware: Add Turris Mox rWTM firmware driver
dt-bindings: firmware: Document cznic,turris-mox-rwtm binding
bus: moxtet: fix unsigned comparison to less than zero
bus: moxtet: remove set but not used variable 'dummy'
ARM: scoop: Use the right include
dt-bindings: power: add Amlogic Everything-Else power domains bindings
soc: amlogic: Add support for Everything-Else power domains controller
fbdev: da8xx: use resource management for dma
fbdev: da8xx-fb: drop a redundant if
fbdev: da8xx-fb: use devm_platform_ioremap_resource()
...
|
|
Pull ARM SoC platform updates from Arnd Bergmann:
"The main change this time around is a cleanup of some of the oldest
platforms based on the XScale and ARM9 CPU cores, which are between 10
and 20 years old.
The Kendin/Micrel/Microchip KS8695, Winbond/Nuvoton W90x900 and Intel
IOP33x/IOP13xx platforms are removed after we determined that nobody
is using them any more.
The TI Davinci and NXP LPC32xx platforms on the other hand are still
in active use and are converted to the ARCH_MULTIPLATFORM build,
meaning that we can compile a kernel that works on these along with
most other ARMv5 platforms. Changes toward that goal are also merged
for IOP32x, but additional work is needed to complete this. Patches
for the remaining ARMv5 platforms have started but need more work and
some testing.
Support for the new ASpeed AST2600 gets added, this is based on the
Cortex-A7 ARMv7 core, and is a newer version of the existing ARMv5 and
ARMv6 chips in the same family.
Other changes include a cleanup of the ST-Ericsson ux500 platform and
the move of the TI Davinci platform to a new clocksource driver"
[ The changes had marked INTEL_IOP_ADMA and USB_LPC32XX as being
buildable on other platforms through COMPILE_TEST, but that causes new
warnings that I most definitely do not want to see during the merge
window as that could hide other issues.
So the COMPILE_TEST option got disabled for them again - Linus ]
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (61 commits)
ARM: multi_v5_defconfig: make DaVinci part of the ARM v5 multiplatform build
ARM: davinci: support multiplatform build for ARM v5
arm64: exynos: Enable exynos-chipid driver
ARM: OMAP2+: Delete an unnecessary kfree() call in omap_hsmmc_pdata_init()
ARM: OMAP2+: move platform-specific asm-offset.h to arch/arm/mach-omap2
ARM: davinci: dm646x: Fix a typo in the comment
ARM: davinci: dm646x: switch to using the clocksource driver
ARM: davinci: dm644x: switch to using the clocksource driver
ARM: aspeed: Enable SMP boot
ARM: aspeed: Add ASPEED AST2600 architecture
ARM: aspeed: Select timer in each SoC
dt-bindings: arm: cpus: Add ASPEED SMP
ARM: imx: stop adjusting ar8031 phy tx delay
mailmap: map old company name to new one @microchip.com
MAINTAINERS: at91: remove the TC entry
MAINTAINERS: at91: Collect all pinctrl/gpio drivers in same entry
ARM: at91: move platform-specific asm-offset.h to arch/arm/mach-at91
MAINTAINERS: Extend patterns for Samsung SoC, Security Subsystem and clock drivers
ARM: s3c64xx: squash samsung_usb_phy.h into setup-usb-phy.c
ARM: debug-ll: Add support for r7s9210
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into devel
gpio: updates for v5.4
- use a helper variable for &pdev->dev in gpio-em
- tweak the ifdefs in GPIO headers
- fix function links in HTML docs
- remove an unneeded error message from ixp4xx
- use the optional clk_get in gpio-mxc instead of checking the return value
- a couple improvements in pca953x
- allow to build gpio-lpc32xx on non-lpc32xx targets
|
|
config GPIO_MOCKUP is defined in a big if GPIOLIB ... endif block so it
doesn't need to depend explicitly on GPIOLIB.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Link: https://lore.kernel.org/r/20190725131002.14597-1-uwe@kleine-koenig.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
I revisited some older patches here, getting two of the remaining
ARM platforms to build with ARCH_MULTIPLATFORM like most others do.
In case of lpc32xx, I created a new set of patches, which seemed
easier than digging out what I did for an older release many
years ago.
* lpc32xx/multiplatform:
ARM: lpc32xx: allow multiplatform build
ARM: lpc32xx: clean up header files
serial: lpc32xx: allow compile testing
net: lpc-enet: allow compile testing
net: lpc-enet: fix printk format strings
net: lpc-enet: fix badzero.cocci warnings
net: lpc-enet: move phy setup into platform code
net: lpc-enet: factor out iram access
gpio: lpc32xx: allow building on non-lpc32xx targets
serial: lpc32xx_hs: allow compile-testing
watchdog: pnx4008_wdt: allow compile-testing
usb: udc: lpc32xx: allow compile-testing
usb: ohci-nxp: enable compile-testing
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The driver uses hardwire MMIO addresses instead of the data
that is passed in device tree. Change it over to only
hardcode the register offset values and allow compile-testing.
Link: https://lore.kernel.org/r/20190809144043.476786-6-arnd@arndb.de
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Tested-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Use the new infrastructure for hierarchical irqchips in
gpiolib.
The major part of the rewrite was dues to the fact that
the driver was passing around a per-irq pointer to
struct thunderx_line * data container, and the central
handlers will assume struct gpio_chip * to be passed
to we need to use the hwirq as index to look up the
struct thunderx_line * for each IRQ.
The pushing and pop:ing of the irqdomain was confusing
because I've never seen this before, but I tried to
replicate it as best I could.
I have no chance to test or debug this so I need
help.
Cc: David Daney <david.daney@cavium.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Brian Masney <masneyb@onstation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190808123242.5359-4-linus.walleij@linaro.org
|
|
This modifies the IXP4xx driver to use the new helpers
to handle the remapping of parent to child hardware irqs
in the gpiolib core.
This pulls the majority of the code out of the driver
and use the generic code in gpiolib.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Lina Iyer <ilina@codeaurora.org>
Cc: Jon Hunter <jonathanh@nvidia.com>
Cc: Sowjanya Komatineni <skomatineni@nvidia.com>
Cc: Bitan Biswas <bbiswas@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Cc: Thierry Reding <treding@nvidia.com>
Cc: Brian Masney <masneyb@onstation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190808123242.5359-2-linus.walleij@linaro.org
|
|
There are three families of IOP machines we support in Linux: iop32x
(which includes EP80219), iop33x and iop13xx (aka IOP34x aka WP8134x).
All products we support in the kernel are based on the first of these,
iop32x, the other families only ever supported the Intel reference
boards but no actual machine anyone could ever buy.
While one could clearly make them all three work in a single kernel
with some work, this takes the easy way out, removing the later two
platforms entirely, under the assumption that there are no remaining
users.
Earlier versions of OpenWRT and Debian both had support for iop32x
but not the others, and they both dropped iop32x as well in their 2015
releases.
Link: https://lore.kernel.org/r/20190809163334.489360-1-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de> # for I2C parts
Acked-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This adds support for interpreting the input and output bits of one
device on Moxtet bus as GPIOs.
This is needed for example by the SFP cage module of Turris Mox.
Link: https://lore.kernel.org/r/20190812161118.21476-5-marek.behun@nic.cz
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The driver uses hardwire MMIO addresses instead of the data
that is passed in device tree. Change it over to only
hardcode the register offset values and allow compile-testing.
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Tested-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull rst conversion of docs from Mauro Carvalho Chehab:
"As agreed with Jon, I'm sending this big series directly to you, c/c
him, as this series required a special care, in order to avoid
conflicts with other trees"
* tag 'docs/v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (77 commits)
docs: kbuild: fix build with pdf and fix some minor issues
docs: block: fix pdf output
docs: arm: fix a breakage with pdf output
docs: don't use nested tables
docs: gpio: add sysfs interface to the admin-guide
docs: locking: add it to the main index
docs: add some directories to the main documentation index
docs: add SPDX tags to new index files
docs: add a memory-devices subdir to driver-api
docs: phy: place documentation under driver-api
docs: serial: move it to the driver-api
docs: driver-api: add remaining converted dirs to it
docs: driver-api: add xilinx driver API documentation
docs: driver-api: add a series of orphaned documents
docs: admin-guide: add a series of orphaned documents
docs: cgroup-v1: add it to the admin-guide book
docs: aoe: add it to the driver-api book
docs: add some documentation dirs to the driver-api book
docs: driver-model: move it to the driver-api book
docs: lp855x-driver.rst: add it to the driver-api book
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Frameworks:
- Set 'struct device' fwnode when registering a new device
New Drivers:
- Add support for ROHM BD70528 PMIC
New Device Support:
- Add support for LP87561 4-Phase Regulator to TI LP87565 PMIC
- Add support for RK809 and RK817 to Rockchip RK808
- Add support for Lid Angle to ChromeOS core
- Add support for CS47L15 CODEC to Madera core
- Add support for CS47L92 CODEC to Madera core
- Add support for ChromeOS (legacy) Accelerometers in ChromeOS core
- Add support for Add Intel Elkhart Lake PCH to Intel LPSS
New Functionality:
- Provide regulator supply information when registering; madera-core
- Additional Device Tree support; lp87565, madera, cros-ec, rohm,bd71837-pmic
- Allow over-riding power button press via Device Tree; rohm-bd718x7
- Differentiate between running processors; cros_ec_dev
Fix-ups:
- Big header file update; cros_ec_commands.h
- Split header per-subsystem; rohm-bd718x7
- Remove superfluous code; menelaus, cs5535-mfd, cs47lXX-tables
- Trivial; sorting, coding style; intel-lpss-pci
- Only remove Power Off functionality if set locally; rk808
- Make use for Power Off Prepare(); rk808
- Fix spelling mistake in header guards; stmfx
- Properly free IDA resources
- SPDX fixups; cs47lXX-tables, madera
- Error path fixups; hi655x-pmic
Bug Fixes:
- Add missing break in case() statement
- Repair undefined behaviour when not initialising variables; arizona-core, madera-core
- Fix reference to Device Tree documentation; madera"
* tag 'mfd-next-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (45 commits)
mfd: hi655x-pmic: Fix missing return value check for devm_regmap_init_mmio_clk
mfd: madera: Fixup SPDX headers
mfd: madera: Remove some unused registers and fix some defaults
mfd: intel-lpss: Release IDA resources
mfd: intel-lpss: Add Intel Elkhart Lake PCH PCI IDs
mfd: cs5535-mfd: Remove ifdef OLPC noise
mfd: stmfx: Fix macro definition spelling
dt-bindings: mfd: Add link to ROHM BD71847 Datasheet
MAINAINERS: Swap words in INTEL PMIC MULTIFUNCTION DEVICE DRIVERS
mfd: cros_ec_dev: Register cros_ec_accel_legacy driver as a subdevice
mfd: rk808: Prepare rk805 for poweroff
mfd: rk808: Check pm_power_off pointer
mfd: cros_ec: differentiate SCP from EC by feature bit
dt-bindings: Add binding for cros-ec-rpmsg
mfd: madera: Add Madera core support for CS47L92
mfd: madera: Add Madera core support for CS47L15
mfd: madera: Update DT bindings to add additional CODECs
mfd: madera: Add supply mapping for MICVDD
mfd: madera: Fix potential uninitialised use of variable
mfd: madera: Fix bad reference to pinctrl.txt file
...
|
|
There are lots of documents under Documentation/*.txt and a few other
orphan documents elsehwere that belong to the driver-API book.
Move them to their right place.
Reviewed-by: Cornelia Huck <cohuck@redhat.com> # vfio-related parts
Acked-by: Logan Gunthorpe <logang@deltatee.com> # switchtec
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the big slew of GPIO changes for the v5.3 kernel cycle. This
is mostly incremental work this time.
Three important things:
- The FMC subsystem is deleted through my tree. This happens through
GPIO as its demise was discussed in relation to a patch decoupling
its GPIO implementation from the standard way of handling GPIO. As
it turns out, that is not the only subsystem it reimplements and
the authors think it is better do scratch it and start over using
the proper kernel subsystems than try to polish the rust shiny. See
the commit (ACKed by the maintainers) for details.
- Arnd made a small devres patch that was ACKed by Greg and goes into
the device core.
- SPDX header change colissions may happen, because at times I've
seen that quite a lot changed during the -rc:s in regards to SPDX.
(It is good stuff, tglx has me convinced, and it is worth the
occasional pain.)
Apart from this is is nothing controversial or problematic.
Summary:
Core:
- When a gpio_chip request GPIOs from itself, it can now fully
control the line characteristics, both machine and consumer flags.
This makes a lot of sense, but took some time before I figured out
that this is how it has to work.
- Several smallish documentation fixes.
New drivers:
- The PCA953x driver now supports the TI TCA9539.
- The DaVinci driver now supports the K3 AM654 SoCs.
Driver improvements:
- Major overhaul and hardening of the OMAP driver by Russell King.
- Starting to move some drivers to the new API passing irq_chip along
with the gpio_chip when adding the gpio_chip instead of adding it
separately.
Unrelated:
- Delete the FMC subsystem"
* tag 'gpio-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (87 commits)
Revert "gpio: tegra: Clean-up debugfs initialisation"
gpiolib: Use spinlock_t instead of struct spinlock
gpio: stp-xway: allow compile-testing
gpio: stp-xway: get rid of the #include <lantiq_soc.h> dependency
gpio: stp-xway: improve module clock error handling
gpio: stp-xway: simplify error handling in xway_stp_probe()
gpiolib: Clarify use of non-sleeping functions
gpiolib: Fix references to gpiod_[gs]et_*value_cansleep() variants
gpiolib: Document new gpio_chip.init_valid_mask field
Documentation: gpio: Fix reference to gpiod_get_array()
gpio: pl061: drop duplicate printing of device name
gpio: altera: Pass irqchip when adding gpiochip
gpio: siox: Use devm_ managed gpiochip
gpio: siox: Add struct device *dev helper variable
gpio: siox: Pass irqchip when adding gpiochip
drivers: gpio: amd-fch: make resource struct const
devres: allow const resource arguments
gpio: ath79: Pass irqchip when adding gpiochip
gpio: tegra: Clean-up debugfs initialisation
gpio: siox: Switch to IRQ_TYPE_NONE
...
|
|
Enable compile-testing of the stp-xway GPIO driver now that it does not
depend on any architecture specific includes anymore.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20190702223248.31934-5-martin.blumenstingl@googlemail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
ROHM BD70528 PMIC has 4 GPIO pins. Allow them to be
controlled by GPIO framework.
IRQs are handled by regmap-irq and GPIO driver is not
aware of the irq usage.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This driver was using the OF GPIO helper API, but barely used any of its
features and it cost more code than it saved. Also, the OF GPIO code is
now deprecated. Convert it to use a more standard setup and use devm
APIs for initialization to avoid the need for a remove function.
Our rationale for this change is that we are using the Xilinx GPIO with
resources injected using the MFD core rather than on the device tree
itself. Using platform rather than OF-specific resources allows this to
work for free.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add K3 dependencies to enable the driver on K3 platforms.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fix from Linus Walleij:
"Fix a build error in gpio-adp5588"
* tag 'gpio-v5.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: fix gpio-adp5588 build errors
|
|
This feature is deprecated, it is helpful to inform users about
this. I'm resisting the temptation to add "depends on BROKEN"
to this, but saving that for later.
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The gpio-adp5588 driver uses interfaces that are provided by
GPIOLIB_IRQCHIP, so select that symbol in its Kconfig entry.
Fixes these build errors:
../drivers/gpio/gpio-adp5588.c: In function ‘adp5588_irq_handler’:
../drivers/gpio/gpio-adp5588.c:266:26: error: ‘struct gpio_chip’ has no member named ‘irq’
dev->gpio_chip.irq.domain, gpio));
^
../drivers/gpio/gpio-adp5588.c: In function ‘adp5588_irq_setup’:
../drivers/gpio/gpio-adp5588.c:298:2: error: implicit declaration of function ‘gpiochip_irqchip_add_nested’ [-Werror=implicit-function-declaration]
ret = gpiochip_irqchip_add_nested(&dev->gpio_chip,
^
../drivers/gpio/gpio-adp5588.c:307:2: error: implicit declaration of function ‘gpiochip_set_nested_irqchip’ [-Werror=implicit-function-declaration]
gpiochip_set_nested_irqchip(&dev->gpio_chip,
^
Fixes: 459773ae8dbb ("gpio: adp5588-gpio: support interrupt controller")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: linux-gpio@vger.kernel.org
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull ARM SoC platform updates from Olof Johansson:
"SoC updates, mostly refactorings and cleanups of old legacy platforms.
Major themes this release:
- Conversion of ixp4xx to a modern platform (drivers, DT, bindings)
- Moving some of the ep93xx headers around to get it closer to
multiplatform enabled.
- Cleanups of Davinci
This also contains a few patches that were queued up as fixes before
5.1 but I didn't get sent in before release"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (123 commits)
ARM: debug-ll: add default address for digicolor
ARM: u300: regulator: add MODULE_LICENSE()
ARM: ep93xx: move private headers out of mach/*
ARM: ep93xx: move pinctrl interfaces into include/linux/soc
ARM: ep93xx: keypad: stop using mach/platform.h
ARM: ep93xx: move network platform data to separate header
ARM: stm32: add AMBA support for stm32 family
MAINTAINERS: update arch/arm/mach-davinci
ARM: rockchip: add missing of_node_put in rockchip_smp_prepare_pmu
ARM: dts: Add queue manager and NPE to the IXP4xx DTSI
soc: ixp4xx: qmgr: Add DT probe code
soc: ixp4xx: qmgr: Add DT bindings for IXP4xx qmgr
soc: ixp4xx: npe: Add DT probe code
soc: ixp4xx: Add DT bindings for IXP4xx NPE
soc: ixp4xx: qmgr: Pass resources
soc: ixp4xx: Remove unused functions
soc: ixp4xx: Uninline several functions
soc: ixp4xx: npe: Pass addresses as resources
ARM: ixp4xx: Turn the QMGR into a platform device
ARM: ixp4xx: Turn the NPE into a platform device
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Framework:
- Document (kerneldoc) core mfd_add_devices() API
New Drivers:
- Altera SOCFPGA System Manager
- Maxim MAX77650/77651 PMIC
- Maxim MAX77663 PMIC
- ST Multi-Function eXpander (STMFX)
New Device Support:
- LEDs support in Intel Cherry Trail Whiskey Cove PMIC
- RTC support in SAMSUNG Electronics S2MPA01 PMIC
- SAM9X60 support in Atmel HLCDC (High-end LCD Controller)
- USB X-Powers AXP 8xx PMICs
- Integrated Sensor Hub (ISH) in ChromeOS EC
- USB PD Logger in ChromeOS EC
- AXP223 in X-Powers AXP series PMICs
- Power Supply in X-Powers AXP 803 PMICs
- Comet Lake in Intel Low Power Subsystem
- Fingerprint MCU in ChromeOS EC
- Touchpad MCU in ChromeOS EC
- Move TI LM3532 support to LED
New Functionality:
- max77650, max77620: Add/extend DT support
- max77620 power-off
- syscon clocking
- croc_ec host sleep event
Fix-ups:
- Trivial; Formatting, spelling, etc; Kconfig, sec-core, ab8500-debugfs
- Remove unused functionality; rk808, da9063-*
- SPDX conversion; da9063-*, atmel-*,
- Adapt/add new register definitions; cs47l35-tables, cs47l90-tables, imx6q-iomuxc-gpr
- Fix-up DT bindings; ti-lmu, cirrus,lochnagar
- Simply obtaining driver data; ssbi, t7l66xb, tc6387xb, tc6393xb
Bug Fixes:
- Fix incorrect defined values; max77620, da9063
- Fix device initialisation; twl6040
- Reset device on init; intel-lpss
- Fix build warnings when !OF; sun6i-prcm
- Register OF match tables; tps65912-spi
- Fix DMI matching; intel_quark_i2c_gpio"
* tag 'mfd-next-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (65 commits)
mfd: Use dev_get_drvdata() directly
mfd: cros_ec: Instantiate properly CrOS Touchpad MCU device
mfd: cros_ec: Instantiate properly CrOS FP MCU device
mfd: cros_ec: Update the EC feature codes
mfd: intel-lpss: Add Intel Comet Lake PCI IDs
mfd: lochnagar: Add links to binding docs for sound and hwmon
mfd: ab8500-debugfs: Fix a typo ("deubgfs")
mfd: imx6sx: Add MQS register definition for iomuxc gpr
dt-bindings: mfd: LMU: Fix lm3632 dt binding example
mfd: intel_quark_i2c_gpio: Adjust IOT2000 matching
mfd: da9063: Fix OTP control register names to match datasheets for DA9063/63L
mfd: tps65912-spi: Add missing of table registration
mfd: axp20x: Add USB power supply mfd cell to AXP803
mfd: sun6i-prcm: Fix build warning for non-OF configurations
mfd: intel-lpss: Set the device in reset state when init
platform/chrome: Add support for v1 of host sleep event
mfd: cros_ec: Add host_sleep_event_v1 command
mfd: cros_ec: Instantiate the CrOS USB PD logger driver
mfd: cs47l90: Make DAC_AEC_CONTROL_2 readable
mfd: cs47l35: Make DAC_AEC_CONTROL_2 readable
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull gpio updates from Linus Walleij:
"This is the bulk of the GPIO changes for the v5.2 kernel cycle. A bit
later than usual because I was ironing out my own mistakes. I'm
holding some stuff back for the next kernel as a result, and this
should be a healthy and well tested batch.
Core changes:
- The gpiolib MMIO driver has been enhanced to handle two direction
registers, i.e. one register to set lines as input and one register
to set lines as output. It turns out some silicon engineer thinks
the ability to configure a line as input and output at the same
time makes sense, this can be debated but includes a lot of analog
electronics reasoning, and the registers are there and need to be
handled consistently. Unsurprisingly, we enforce the lines to be
either inputs or outputs in such schemes.
- Send in the proper argument value to .set_config() dispatched to
the pin control subsystem. Nobody used it before, now someone does,
so fix it to work as expected.
- The ACPI gpiolib portions can now handle pin bias setting (pull up
or pull down). This has been in the ACPI spec for years and we
finally have it properly integrated with Linux GPIOs. It was based
on an observation from Andy Schevchenko that Thomas Petazzoni's
changes to the core for biasing the PCA950x GPIO expander actually
happen to fit hand-in-glove with what the ACPI core needed. Such
nice synergies happen sometimes.
New drivers:
- A new driver for the Mellanox BlueField GPIO controller. This is
using 64bit MMIO registers and can configure lines as inputs and
outputs at the same time and after improving the MMIO library we
handle it just fine. Interesting.
- A new IXP4xx proper gpiochip driver with hierarchical interrupts
should be coming in from the ARM SoC tree as well.
Driver enhancements:
- The PCA053x driver handles the CAT9554 GPIO expander.
- The PCA053x driver handles the NXP PCAL6416 GPIO expander.
- Wake-up support on PCA053x GPIO lines.
- OMAP now does a nice asynchronous IRQ handling on wake-ups by
letting everything wake up on edges, and this makes runtime PM work
as expected too.
Misc:
- Several cleanups such as devres fixes.
- Get rid of some languager comstructs that cause problems when
compiling with LLVMs clang.
- Documentation review and update"
* tag 'gpio-v5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (85 commits)
gpio: Update documentation
docs: gpio: convert docs to ReST and rename to *.rst
gpio: sch: Remove write-only core_base
gpio: pxa: Make two symbols static
gpiolib: acpi: Respect pin bias setting
gpiolib: acpi: Add acpi_gpio_update_gpiod_lookup_flags() helper
gpiolib: acpi: Set pin value, based on bias, more accurately
gpiolib: acpi: Change type of dflags
gpiolib: Introduce GPIO_LOOKUP_FLAGS_DEFAULT
gpiolib: Make use of enum gpio_lookup_flags consistent
gpiolib: Indent entry values of enum gpio_lookup_flags
gpio: pca953x: add support for pca6416
dt-bindings: gpio: pca953x: document the nxp,pca6416
gpio: pca953x: add pcal6416 to the of_device_id table
gpio: gpio-omap: Remove conditional pm_runtime handling for GPIO interrupts
gpio: gpio-omap: configure edge detection for level IRQs for idle wakeup
tracing: stop making gpio tracing configurable
gpio: pca953x: Configure wake-up path when wake-up is enabled
gpio: of: Optimize quirk checks
gpio: mmio: Drop bgpio_dir_inverted
...
|
|
Add GPIO support for max77650 mfd device. This PMIC exposes a single
GPIO line.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This adds a driver for the IXP4xx GPIO block found in
the Intel XScale IXP4xx systems.
The GPIO part of this block is pretty straight-forward and
just uses the generic MMIO GPIO library.
The irqchip side of this driver is hierarchical where
the main irqchip will receive a processed level trigger
in response to the edge detector of the GPIO block,
so for this reason the v2 version of the irqdomain API
is used (as well as in the parent IXP4xx irqchip) and
masking, unmasking and setting up the type on IRQ
happens on several levels.
Currently this GPIO controller will grab the parent
irqdomain using a special function, but as the platform
move toward device tree probing, this will not be needed:
we can just look up the parent irqdomain from the device
tree.
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Make the anon_inodes facility unconditional so that it can be used by core
VFS code and pidfd code.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[christian@brauner.io: adapt commit message to mention pidfds]
Signed-off-by: Christian Brauner <christian@brauner.io>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into devel
gpio: updates for v5.2 (part 1)
- batch of improvements for the vf610 driver which shrink the code and
make use of resource managed helpers
- support for a new variant of pca953x
- make gpio-mockup buildable on systems without IOMEM
- make gpio-74x164 more flexible by using generic device properties
plus minor improvements
- new driver for Mellanox BlueField
- fixes for wakeup GPIOs in gpio-omap
- use devm_platform_ioremap_resource() in gpio-mxc
- a couple improvements of kernel docs for ACPI code
- don't WARN() in gpiod_put() on optional GPIOs
|
|
Align the Kconfig formatting with the vast majority of the Kconfig
files, to make it a bit easier / more pleasant to read ;-)
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Fixes a compile test failure
Fixes: c78c42d77165 ("gpio: add driver for Mellanox BlueField GPIO controller")
Signed-off-by: Shravan Kumar Ramani <sramani@mellanox.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
This patch adds support for the GPIO controller used by Mellanox
BlueField SOCs.
Reviewed-by: David Woods <dwoods@mellanox.com>
Signed-off-by: Shravan Kumar Ramani <sramani@mellanox.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
The testing driver doesn't really depend on HAS_IOMEM. We may want to
build it for testing purposes on architectures not supporting IOMEM,
for example: on user-mode linux. Move it out of the "Memory Mapped GPIO
drivers" section.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
The testing module doesn't need GPIO irqchip nor does it depend on
sysfs. Remove unnecessary dependencies from Kconfig.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
GPIO platform driver for the AMD G-series PCH (eg. on GX-412TC)
This driver doesn't registers itself automatically, as it needs to
be provided with platform specific configuration, provided by some
board driver setup code.
Didn't implement oftree probing yet, as it's rarely found on x86.
Cc: linux-gpio@vger.kernel.org
Cc: linus.walleij@linaro.org
Cc: bgolaszewski@baylibre.com
Cc: dvhart@infradead.org
Cc: platform-driver-x86@vger.kernel.org
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds a driver for Gateworks PLD GPIO, that exist in
two instances on the Gateworks Cambria GW2358-4 router
platform at least.
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Some TQ-Systems ComExpress modules contain an IO controller with 8
GPIO lines.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch implements level-triggered IRQs in the Hollywood GPIO driver.
Edge triggered interrupts are not supported in this GPIO controller, so
I moved their emulation into a separate patch.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This driver clearly needs OF_GPIO so depend on it.
Fixes a build error.
Cc: Andrei Stefanescu <Andrei.Stefanescu@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch adds a driver for Cadence GPIO controller.
It can be enabled with GPIO_CADENCE Kconfig option.
It uses generic GPIO infrastructure and works
as an interrupt controller.
At the moment it only supports level sensitive irqs.
Signed-off-by: Jan Kotas <jank@cadence.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
PIOBU pins do not lose their voltage during Backup/Self-refresh.
This patch adds a simple GPIO controller for them and a
maintainer for the driver.
This driver adds support for using the pins as GPIO
offering the possibility to read/set the voltage.
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Select REGMAP_I2C in Kconfig, since the driver now depends on regmap
and this was missing, thus breaking build on various systems.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The change adds support of LPC18xx/LPC43xx GPIO pin interrupt controller
block within SoC GPIO controller. The new interrupt controller driver
allows to configure and capture edge or level interrupts on 8 arbitrary
selectedinput GPIO pins, and lift the signals to be reported as NVIC rising
edge interrupts. Configuration of a particular GPIO pin to serve as
interrupt and its mapping to an interrupt on NVIC is done by SCU pin
controller, for more details see description of 'nxp,gpio-pin-interrupt'
device tree property of a GPIO pin [1].
From LPC18xx and LPC43xx User Manuals the GPIO controller consists of
the following blocks:
* GPIO pin interrupt block at 0x40087000, this change adds its support,
* GPIO GROUP0 interrupt block at 0x40088000,
* GPIO GROUP1 interrupt block at 0x40089000,
* GPIO port block at 0x400F4000, it is supported by the original driver.
While all 4 sub-controller blocks have their own I/O addresses, moreover
all 3 interrupt blocks are APB0 peripherals and high-speed GPIO block is
an AHB slave, according to the hardware manual the GPIO controller is
seen as a single block, and 4 sub-controllers have the shared reset signal
RGU #28 and clock to register interface CLK_CPU_GPIO on CCU1.
Likely support of two GPIO group interrupt blocks won't be added in short
term, because the mechanism to mask several interrupt sources is not well
defined.
[1] Documentation/devicetree/bindings/pinctrl/nxp,lpc1850-scu.txt
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Fix kconfig warning for GPIO_SNPS_CREG:
WARNING: unmet direct dependencies detected for OF_GPIO
Depends on [n]: GPIOLIB [=y] && OF [=n] && HAS_IOMEM [=y]
Selected by [y]:
- GPIO_SNPS_CREG [=y] && GPIOLIB [=y] && HAS_IOMEM [=y] && (ARC || COMPILE_TEST [=y])
Drivers in drivers/gpio/Kconfig depend on OF_GPIO, not select it.
This prevents attempting to build when OF is not enabled.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add single-register MMIO GPIO driver for complex cases where
only several fields in register belong to GPIO lines and each GPIO
line owns a field with different length and on/off value.
Such CREG GPIOs are used in Synopsys AXS10x and HSDK boards.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This driver controls a SIOX device that provides 20 I/O lines. The first
twelve are fixed inputs, the remaining eight are outputs.
Acked-by: Gavin Schenk <g.schenk@eckelmann.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
|
|
The pinctrl-ingenic driver is now handling the GPIO chips directly.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
We can quite easily switch banks/ports A and B to use
GPIOLIB_IRQCHIP which is code that will be more careful
about handling interrupt descriptors and use a proper
irqdomain for translating the IRQs. This cuts down some
code in favor of using the implementation inside
gpiolib.
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
