| Age | Commit message (Collapse) | Author |
|---|
|
Honour deferred probing for devm_clk_get() so that we can get the clock
for PWM.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Hogs are added *after* ACPI so should be removed *before* in error path.
Fixes: a411e81e61df ("gpiolib: add hogs support for machine code")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
After shuffling the code, error path wasn't updated correctly.
Fix it here.
Fixes: 2f4133bb5f14 ("gpiolib: No need to call gpiochip_remove_pin_ranges() twice")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Chip outputs are enabled[1] before actual reset is performed[2] which might
cause pin output value to flip flop if previous pin value was set to 1.
Fix that behavior by making sure chip is fully reset before all outputs are
enabled.
Flip-flop can be noticed when module is removed and inserted again and one of
the pins was changed to 1 before removal. 100 microsecond flipping is
noticeable on oscilloscope (100khz SPI bus).
For a properly reset chip - output is enabled around 100 microseconds (on 100khz
SPI bus) later during probing process hence should be irrelevant behavioral
change.
Fixes: 7ebc194d0fd4 (gpio: 74x164: Introduce 'enable-gpios' property)
Link: https://elixir.bootlin.com/linux/v6.7.4/source/drivers/gpio/gpio-74x164.c#L130 [1]
Link: https://elixir.bootlin.com/linux/v6.7.4/source/drivers/gpio/gpio-74x164.c#L150 [2]
Signed-off-by: Arturas Moskvinas <arturas.moskvinas@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Similar to gpiochip_generic_request() and gpiochip_generic_free() the
gpiochip_generic_config() function needs to handle the case where there
are no pinctrl pins mapped to the GPIOs, usually through the gpio-ranges
device tree property.
Commit f34fd6ee1be8 ("gpio: dwapb: Use generic request, free and
set_config") set the .set_config callback to gpiochip_generic_config()
in the dwapb GPIO driver so the GPIO API can set pinctrl configuration
for the corresponding pins. Most boards using the dwapb driver do not
set the gpio-ranges device tree property though, and in this case
gpiochip_generic_config() would return -EPROPE_DEFER rather than the
previous -ENOTSUPP return value. This in turn makes
gpio_set_config_with_argument_optional() fail and propagate the error to
any driver requesting GPIOs.
Fixes: 2956b5d94a76 ("pinctrl / gpio: Introduce .set_config() callback for GPIO chips")
Reported-by: Jisheng Zhang <jszhang@kernel.org>
Closes: https://lore.kernel.org/linux-gpio/ZdC_g3U4l0CJIWzh@xhacker/
Tested-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Since commit 48e1b4d369cf ("gpiolib: remove the GPIO device from the list
when it's unregistered") we remove the GPIO device entry from the global
list (used to order devices by their GPIO ranges) when unregistering the
chip, not when releasing the device. It will not happen when the last
reference is put anymore. This means, we need to remove it in error path
in gpiochip_add_data_with_key() unconditionally, without checking if the
device's .release() callback is set.
Fixes: 48e1b4d369cf ("gpiolib: remove the GPIO device from the list when it's unregistered")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
The raw interrupt status of eic maybe set before the interrupt is enabled,
since the eic interrupt has a latch function, which would trigger the
interrupt event once enabled it from user side. To solve this problem,
interrupts generated before setting the interrupt trigger type are ignored.
Fixes: 25518e024e3a ("gpio: Add Spreadtrum EIC driver support")
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Signed-off-by: Wenhua Lin <Wenhua.Lin@unisoc.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Spurious wakeups are reported on the GPD G1619-04 which
can be absolved by programming the GPIO to ignore wakeups.
Cc: stable@vger.kernel.org
Reported-and-tested-by: George Melikov <mail@gmelikov.ru>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3073
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
"Apart from some regular driver fixes there's a relatively big revert
of the locking changes that were introduced to GPIOLIB in this merge
window.
This is because it turned out that some legacy GPIO interfaces - that
need to translate a number from the global GPIO numberspace to the
address of the relevant descriptor, thus running a GPIO device lookup
and taking the GPIO device list lock - are still used in old code from
atomic context resulting in "scheduling while atomic" errors.
I'll try to make the read-only part of the list access entirely
lockless using SRCU but this will take some time so let's go back to
the old global spinlock for now.
Summary:
- revert the changes aiming to use a read-write semaphore to protect
the list of GPIO devices due to calls to legacy API taking that
lock from atomic context in old code
- fix inverted logic in DEFINE_FREE() for GPIO device references
- check the return value of bgpio_init() in gpio-mlxbf3
- fix node address in the DT bindings example for gpio-xilinx
- fix signedness bug in gpio-rtd
- fix kernel-doc warnings in gpio-en7523"
* tag 'gpio-fixes-for-v6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpiolib: revert the attempt to protect the GPIO device list with an rwsem
gpio: EN7523: fix kernel-doc warnings
gpiolib: Fix scope-based gpio_device refcounting
gpio: mlxbf3: add an error code check in mlxbf3_gpio_probe
dt-bindings: gpio: xilinx: Fix node address in gpio
gpio: rtd: Fix signedness bug in probe
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight updates from Lee Jones:
"New Drivers:
- Add support for Monolithic Power Systems MP3309C WLED Step-up Converter
Fix-ups:
- Use/convert to new/better APIs/helpers/MACROs instead of
hand-rolling implementations
- Device Tree Binding updates
- Demote non-kerneldoc header comments
- Improve error handling; return proper error values, simplify, avoid
duplicates, etc
- Convert over to the new (kinda) GPIOD API
Bug Fixes:
- Fix uninitialised local variable"
* tag 'backlight-next-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
backlight: hx8357: Convert to agnostic GPIO API
backlight: ili922x: Add an error code check in ili922x_write()
backlight: ili922x: Drop kernel-doc for local macros
backlight: mp3309c: Fix uninitialized local variable
backlight: pwm_bl: Use dev_err_probe
backlight: mp3309c: Add support for MPS MP3309C
dt-bindings: backlight: mp3309c: Remove two required properties
|
|
This reverts commits 1979a2807547 ("gpiolib: replace the GPIO device
mutex with a read-write semaphore") and 65a828bab158 ("gpiolib: use
a mutex to protect the list of GPIO devices").
Unfortunately the legacy GPIO API that's still used in older code has to
translate numbers from the global GPIO numberspace to descriptors. This
results in a GPIO device lookup in every call to legacy functions. Some
of those functions - like gpio_set/get_value() - can be called from
atomic context so taking a sleeping lock that is an RW semaphore results
in an error.
We'll probably have to protect this list with SRCU.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/linux-wireless/f7b5ff1e-8f34-4d98-a7be-b826cb897dc8@moroto.mountain/
Fixes: 1979a2807547 ("gpiolib: replace the GPIO device mutex with a read-write semaphore")
Fixes: 65a828bab158 ("gpiolib: use a mutex to protect the list of GPIO devices")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Add "struct" keyword and explain the @dir array differently to
prevent kernel-doc warnings:
gpio-en7523.c:22: warning: cannot understand function prototype: 'struct airoha_gpio_ctrl '
gpio-en7523.c:27: warning: Function parameter or struct member 'dir' not described in 'airoha_gpio_ctrl'
gpio-en7523.c:27: warning: Excess struct member 'dir0' description in 'airoha_gpio_ctrl'
gpio-en7523.c:27: warning: Excess struct member 'dir1' description in 'airoha_gpio_ctrl'
Fixes: 0868ad385aff ("gpio: Add support for Airoha EN7523 GPIO controller")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Clang static checker warning: Value stored to 'ret' is never read.
bgpio_init() returns error code if failed, it's better to add this
check.
Fixes: cd33f216d241 ("gpio: mlxbf3: Add gpio driver support")
Signed-off-by: Su Hui <suhui@nfschina.com>
[Bartosz: add the Fixes: tag]
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
The "data->irqs[]" array holds unsigned int so this error handling will
not work correctly.
Fixes: eee636bff0dc ("gpio: rtd: Add support for Realtek DHC(Digital Home Center) RTD SoCs")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
There are only two spots where we modify (add to or remove objects from)
the GPIO device list. Readers should be able to access it concurrently.
Replace the mutex with a read-write semaphore and adjust the locking
operations accordingly.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
|
If we wait until the GPIO device's .release() callback gets invoked
before we remove it from the global device list, then we risk that
someone will look it up using gpio_device_find() between where we
dropped the last reference and before .release() is done taking a
reference again to an object that's being released.
The device must be removed when it's being unregistered - just like how
we remove it from the GPIO bus.
Fixes: ff2b13592299 ("gpio: make the gpiochip a real device")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add Nuvoton BMC NPCM7xx/NPCM8xx sgpio driver support.
Nuvoton NPCM SGPIO module is combine serial to parallel IC (HC595)
and parallel to serial IC (HC165), and use APB3 clock to control it.
This interface has 4 pins (D_out , D_in, S_CLK, LDSH).
BMC can use this driver to increase 64 GPI pins and 64 GPO pins to use.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
This driver enables configuration of GPIO direction, GPIO values, GPIO
debounce settings and handles GPIO interrupts.
Signed-off-by: Tzuyi Chang <tychang@realtek.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
A bank PMIC EIC contains 16 EICs, and the operating registers
are BIT0-BIT15, such as BIT0 of the register operated by EIC0.
Using the one-dimensional array reg[CACHE_NR_REGS] for maintenance
will cause the configuration of other EICs to be affected when
operating a certain EIC. In order to solve this problem, configure
the bit corresponding to the EIC through offset.
Signed-off-by: Wenhua Lin <Wenhua.Lin@unisoc.com>
Reviewed-by: Chunyan Zhang <zhang.lyra@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
This way GPIO will be denied on pins already claimed by other devices
and basic pin configuration (pull-up, pull-down etc.) can be done
through the userspace GPIO API.
Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Older code has an annoying habit of putting tabs between the type and the
name of the variable. This doesn't really add to readability and newer
code doesn't do it so make the entire file consistent.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Older code has an annoying habit of putting tabs between the type and the
name of the variable. This doesn't really add to readability and newer
code doesn't do it so make the entire file consistent.
While at it: convert 'unsigned' to 'unsigned int'.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
extra_checks is only used in a few places. It also depends on
a non-standard DEBUG define one needs to add to the source file. The
overhead of removing it should be minimal (we already use pure
might_sleep() in the code anyway) so drop it.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
|
CONFIG_DEBUG_GPIO should only be used to enable debug log messages and
for core GPIOLIB debugging. Don't use it to control the execution of
potentially buggy code. Just put it under an always-false #if.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Replace the wrapping functions that inhibit removal of the gpio chip
with equivalent guards.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
After the adoption of guard(), the locking wrappers that hold the
config_mutex for linereq_set_values() and linereq_set_config() no
longer add value, so combine them into the functions they wrap.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
The size of struct linereq may exceed a page, so allocate space for
it using kvzalloc() instead of kzalloc() to handle the case where
memory is heavily fragmented and kzalloc() cannot find a sufficient
contiguous region.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
struct_size() is used to calculate struct linereq size, so explicitly
include overflow.h.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Linux 6.7-rc7
|
|
In the hardware implementation of the I2C HID driver based on DesignWare
GPIO IRQ chip, when the user continues to use the I2C HID device in the
suspend process, the I2C HID interrupt will be masked after the resume
process is finished.
This is because the disable_irq()/enable_irq() of the DesignWare GPIO
driver does not synchronize the IRQ mask register state. In normal use
of the I2C HID procedure, the GPIO IRQ irq_mask()/irq_unmask() functions
are called in pairs. In case of an exception, i2c_hid_core_suspend()
calls disable_irq() to disable the GPIO IRQ. With low probability, this
causes irq_unmask() to not be called, which causes the GPIO IRQ to be
masked and not unmasked in enable_irq(), raising an exception.
Add synchronization to the masked register state in the
dwapb_irq_enable()/dwapb_irq_disable() function. mask the GPIO IRQ
before disabling it. After enabling the GPIO IRQ, unmask the IRQ.
Fixes: 7779b3455697 ("gpio: add a driver for the Synopsys DesignWare APB GPIO block")
Cc: stable@kernel.org
Co-developed-by: Riwen Lu <luriwen@kylinos.cn>
Signed-off-by: Riwen Lu <luriwen@kylinos.cn>
Signed-off-by: xiongxin <xiongxin@kylinos.cn>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
While the GPIO cdev gpio_ioctl() call is in progress, the kernel can
call gpiochip_remove() which will set gdev->chip to NULL, after which
any subsequent access will cause a crash.
gpio_ioctl() was overlooked by the previous fix to protect syscalls
(bdbbae241a04), so add protection for that.
Fixes: bdbbae241a04 ("gpiolib: protect the GPIO device against being dropped while in use by user-space")
Fixes: d7c51b47ac11 ("gpio: userspace ABI for reading/writing GPIO lines")
Fixes: 3c0d9c635ae2 ("gpiolib: cdev: support GPIO_V2_GET_LINE_IOCTL and GPIO_V2_LINE_GET_VALUES_IOCTL")
Fixes: aad955842d1c ("gpiolib: cdev: support GPIO_V2_GET_LINEINFO_IOCTL and GPIO_V2_GET_LINEINFO_WATCH_IOCTL")
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Reduce the time holding the gpio_lock by snapshotting the desc flags,
rather than testing them individually while holding the lock.
Accept that the calculation of the used field is inherently racy, and
only check the availability of the line from pinctrl if other checks
pass, so avoiding the check for lines that are otherwise in use.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Add documentation of the algorithm used to perform scatter/gather
of the requested lines and values in linereq_get_values() and
linereq_set_values_unlocked() to improve maintainability.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Use guard() or scoped_guard() for critical sections rather than
discrete lock/unlock pairs.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
cdev is the only user of the debounce_period_us field in
struct gpio_desc, and it no longer uses it, so remove it.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Store the debounce period for a requested line locally, rather than in
the debounce_period_us field in the gpiolib struct gpio_desc.
Add a global tree of lines containing supplemental line information
to make the debounce period available to be reported by the
GPIO_V2_GET_LINEINFO_IOCTL and the line change notifier.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/andy/linux-gpio-intel into gpio/for-next
intel-gpio for v6.8-1
* Use RAII for locking in the Tangier family of drivers (Raag)
* Update Tangier family of drivers to use new PM helpers (Raag)
The following is an automated git shortlog grouped by driver:
elkhartlake:
- reuse pm_ops from Intel Tangier driver
tangier:
- simplify locking using cleanup helpers
- unexport suspend/resume handles
- use EXPORT_NS_GPL_SIMPLE_DEV_PM_OPS() helper
|
|
There is a few things done:
- include only the headers we are direct user of
- add missing headers
- group generic headers and subsystem headers
- sort each group alphabetically
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Convert the module to be property provider agnostic and allow
it to be used on non-OF platforms.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
The global list of GPIO devices is never modified or accessed from
atomic context so it's fine to protect it using a mutex. Add a new
global lock dedicated to the gpio_devices list and use it whenever
accessing or modifying it.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Rename two functions that read or modify the global GPIO device list but
don't take the lock themselves (and need to be called with it already
acquired). Use the _unlocked() suffix which seems to be used quite
consistently across the kernel despite there also existing the _locked()
suffix for the same purpose.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
The irqchip field has been removed from struct xgpio_instance so remove
the doc as well.
Fixes: b4510f8fd5d0 ("gpio: xilinx: Convert to immutable irq_chip")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202312150239.IyuTVvrL-lkp@intel.com/
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
|
|
We will eventually switch to protecting the GPIO descriptors with a mutex
but until then, we need to allocate memory for the label copy atomically
while we're holding the global spinlock.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/linux-gpio/62588146-eed6-42f7-ba26-160226b109fe@moroto.mountain/T/#u
Fixes: f8d05e276b45 ("gpiolib: remove gpiochip_is_requested()")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The of_gpio.h is going to be removed. In preparation of that convert
the driver to the agnostic API.
Fixes: fbbbcd177a27 ("gpiolib: of: add quirk for locating reset lines with legacy bindings")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20231207161513.3195509-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Provide a custom implementation of the dbg_show() callback that prints
all requested lines together with their label, direction, value and
bias. This improves the code coverage of GPIOLIB.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
gpio: remove gpiochip_is_requested()
- provide a safer alternative to gpiochip_is_requested()
- convert all existing users
- remove gpiochip_is_requested()
|
|
We have no external users of gpiochip_is_requested(). Let's remove it
and replace its internal calls with direct testing of the REQUESTED flag.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use the new gpiochip_dup_line_label() helper to safely retrieve the
descriptor label.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use the new gpiochip_dup_line_label() helper to safely retrieve the
descriptor label.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use the new gpiochip_dup_line_label() helper to safely retrieve the
descriptor label.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
