summaryrefslogtreecommitdiff
path: root/drivers/gpu/drm/bridge/synopsys
AgeCommit message (Collapse)Author
2019-10-15drm/bridge: dw-hdmi: Restore audio when setting a modeDaniel Kurtz
When setting a new display mode, dw_hdmi_setup() calls dw_hdmi_enable_video_path(), which disables all hdmi clocks, including the audio clock. We should only (re-)enable the audio clock if audio was already enabled when setting the new mode. Without this patch, on RK3288, there will be HDMI audio on some monitors if i2s was played to headphone when the monitor was plugged. ACER H277HU and ASUS PB278 are two of the monitors showing this issue. Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org> Signed-off-by: Daniel Kurtz <djkurtz@chromium.org> Signed-off-by: Yakir Yang <ykk@rock-chips.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191008102145.55134-1-cychiang@chromium.org
2019-10-10drm/bridge: dw-hdmi: Add Dynamic Range and Mastering InfoFrame supportJonas Karlman
Add support for configuring Dynamic Range and Mastering InfoFrame from the hdr_output_metadata connector property. This patch adds a use_drm_infoframe flag to dw_hdmi_plat_data that platform drivers use to signal when Dynamic Range and Mastering infoframes is supported. This flag is needed because Amlogic GXBB and GXL report same DW-HDMI version, and only GXL support DRM InfoFrame. These changes were based on work done by Zheng Yang <zhengyang@rock-chips.com> to support DRM InfoFrame on the Rockchip 4.4 BSP kernel at [1] and [2] [1] https://github.com/rockchip-linux/kernel/tree/develop-4.4 [2] https://github.com/rockchip-linux/kernel/commit/d1943fde81ff41d7cca87f4a42f03992e90bddd5 Cc: Zheng Yang <zhengyang@rock-chips.com> Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/HE1PR06MB4011D7B916CBF8B740ACC45FAC9B0@HE1PR06MB4011.eurprd06.prod.outlook.com
2019-10-07drm/bridge: dw-hdmi: Refuse DDC/CI transfers on the internal I2C controllerMatthias Kaehlcke
The DDC/CI protocol involves sending a multi-byte request to the display via I2C, which is typically followed by a multi-byte response. The internal I2C controller only allows single byte reads/writes or reads of 8 sequential bytes, hence DDC/CI is not supported when the internal I2C controller is used. The I2C transfers complete without errors, however the data in the response is garbage. Abort transfers to/from slave address 0x37 (DDC) with -EOPNOTSUPP, to make it evident that the communication is failing. Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Sean Paul <sean@poorly.run> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191002124354.v2.1.I709dfec496f5f0b44a7b61dcd4937924da8d8382@changeid
2019-10-07cec: add cec_adapter to cec_notifier_cec_adap_unregister()Hans Verkuil
It is possible for one HDMI connector to have multiple CEC adapters. The typical real-world scenario is that where one adapter is used when the device is in standby, and one that's better/smarter when the device is powered up. The cec-notifier changes were made with that in mind, but I missed that in order to support this you need to tell cec_notifier_cec_adap_unregister() which adapter you are unregistering from the notifier. Add this additional argument. It is currently unused, but once all drivers use this, the CEC core will be adapted for these use-cases. Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/e9fc8740-6be6-43a7-beee-ce2d7b54936e@xs4all.nl
2019-10-03Merge drm/drm-next into drm-misc-nextMaxime Ripard
We haven't done any backmerge for a while due to the merge window, and it starts to become an issue for komeda. Let's bring 5.4-rc1 in. Signed-off-by: Maxime Ripard <mripard@kernel.org>
2019-09-25drm/bridge/synopsys: dsi: Use devm_platform_ioremap_resource() in ↵Markus Elfring
__dw_mipi_dsi_probe() Simplify this function implementation by using a known wrapper function. This issue was detected by using the Coccinelle software. Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Reviewed-by: Yannick Fertré <yannick.fertre@st.com> Tested-by: Yannick Fertré <yannick.fertre@st.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/e0d7b7d7-3e89-8b3f-04ed-0b14806e66f7@web.de
2019-09-13drm: bridge/dw_hdmi: add audio sample channel status settingYakir Yang
When transmitting IEC60985 linear PCM audio, we configure the Aduio Sample Channel Status information in the IEC60958 frame. The status bit is already available in iec.status of hdmi_codec_params. This fix the issue that audio does not come out on some monitors (e.g. LG 22CV241) Note that these registers are only for interfaces: I2S audio interface, General Purpose Audio (GPA), or AHB audio DMA (AHBAUDDMA). For S/PDIF interface this information comes from the stream. Currently this function dw_hdmi_set_channel_status is only called from dw-hdmi-i2s-audio in I2S setup. Signed-off-by: Yakir Yang <ykk@rock-chips.com> Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org> Reviewed-by: Jonas Karlman <jonas@kwiboo.se> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190911082646.134347-1-cychiang@chromium.org
2019-09-08drm/bridge: panel: Infer connector type from panel by defaultLaurent Pinchart
The drm panel bridge creates a connector using a connector type explicitly passed by the display controller or bridge driver that instantiates the panel bridge. Now that drm_panel reports its connector type, we can use it to avoid passing an explicit (and often incorrect) connector type to drm_panel_bridge_add() and devm_drm_panel_bridge_add(). Several drivers report incorrect or unknown connector types to userspace. Reporting a different type may result in a breakage. For that reason, rename (devm_)drm_panel_bridge_add() to (devm_)drm_panel_bridge_add_typed(), and add new (devm_)drm_panel_bridge_add() functions that use the panel connector type. Update all callers of (devm_)drm_panel_bridge_add() to the _typed function, they will be converted one by one after testing. The panel drivers have been updated with the following Coccinelle semantic patch, with manual inspection and fixes to indentation. @@ expression bridge; expression dev; expression panel; identifier type; @@ ( -bridge = drm_panel_bridge_add(panel, type); +bridge = drm_panel_bridge_add_typed(panel, type); | -bridge = devm_drm_panel_bridge_add(dev, panel, type); +bridge = devm_drm_panel_bridge_add_typed(dev, panel, type); ) Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190904132804.29680-3-laurent.pinchart@ideasonboard.com
2019-09-02drm: dw-hdmi-i2s: enable audio clock in audio_startupCheng-Yi Chiang
In the designware databook, the sequence of enabling audio clock and setting format is not clearly specified. Currently, audio clock is enabled in the end of hw_param ops after setting format. On some monitors, there is a possibility that audio does not come out. Fix this by enabling audio clock in audio_startup ops before hw_param ops setting format. Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Jonas Karlman <jonas@kwiboo.se> Tested-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190902035435.44463-1-cychiang@chromium.org
2019-08-28drm: Stop including drm_bridge.h from drm_crtc.hBoris Brezillon
We are about to add a drm_bridge_state that inherits from drm_private_state which is defined in drm_atomic.h. Problem is, drm_atomic.h includes drm_crtc.h which in turn includes drm_bridge.h, leading to "drm_private_state has incomplete type" error. Let's force all users of the drm_bridge API to explicitly include drm_bridge.h. Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com> Reviewed-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190826152649.13820-2-boris.brezillon@collabora.com
2019-08-27Merge tag 'drm-misc-next-2019-08-23' of ↵Dave Airlie
git://anongit.freedesktop.org/drm/drm-misc into drm-next drm-misc-next for 5.4: UAPI Changes: Cross-subsystem Changes: Core Changes: - dma-buf: dma-fence selftests Driver Changes: - kirin: Various cleanups and reworks - komeda: Add support for DT memory-regions - meson: Rely on the compatible to detect vpu features - omap: Implement alpha and pixel blend mode properties - panfrost: Implement per-fd address spaces, various fixes - rockchip: DSI DT binding rework - fbdev: Various cleanups Signed-off-by: Dave Airlie <airlied@redhat.com> From: Maxime Ripard <maxime.ripard@bootlin.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190823083509.c7mduqdqjnxc7ubb@flea
2019-08-22Merge tag 'du-next-20190816' of git://linuxtv.org/pinchartl/media into drm-nextDave Airlie
- R-Car DU fixes - Misc. DRM cleanups Signed-off-by: Dave Airlie <airlied@redhat.com> From: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190816133500.GJ5020@pendragon.ideasonboard.com
2019-08-20dw-hdmi-cec: use cec_notifier_cec_adap_(un)registerDariusz Marcinkiewicz
Use the new cec_notifier_cec_adap_(un)register() functions to (un)register the notifier for the CEC adapter. Also adds CEC_CAP_CONNECTOR_INFO capability to the adapter. Changes since v3: - add CEC_CAP_CONNECTOR_INFO to cec_allocate_adapter, - replace CEC_CAP_LOG_ADDRS | CEC_CAP_TRANSMIT | CEC_CAP_RC | CEC_CAP_PASSTHROUGH with CEC_CAP_DEFAULTS. Signed-off-by: Dariusz Marcinkiewicz <darekm@google.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190814104520.6001-4-darekm@google.com
2019-08-20drm: dw-hdmi: use cec_notifier_conn_(un)registerDariusz Marcinkiewicz
Use the new cec_notifier_conn_(un)register() functions to (un)register the notifier for the HDMI connector, and fill in the cec_connector_info. Changes since v6: - move cec_notifier_conn_unregister to a bridge detach function, - add a mutex protecting a CEC notifier. Changes since v4: - typo fix Changes since v2: - removed unnecessary NULL check before a call to cec_notifier_conn_unregister, - use cec_notifier_phys_addr_invalidate to invalidate physical address. Changes since v1: Add memory barrier to make sure that the notifier becomes visible to the irq thread once it is fully constructed. Signed-off-by: Dariusz Marcinkiewicz <darekm@google.com> Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190814104520.6001-9-darekm@google.com
2019-08-16drm: Don't include drm/drm_encoder_slave.h when not neededLaurent Pinchart
The dw-hdmi, kirin and imx drivers include the drm/drm_encoder_slave.h header but don't use the encoder slave API. Remove it or replace it with drm/drm_encoder.h as needed. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2019-08-14drm/bridge: dw-hdmi-i2s: add .get_eld supportJerome Brunet
Provide the eld to the generic hdmi-codec driver. This will let the driver enforce the maximum channel number and set the channel allocation depending on the hdmi sink. Cc: Jonas Karlman <jonas@kwiboo.se> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Reviewed-by: Jonas Karlman <jonas@kwiboo.se> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190812125016.20169-1-jbrunet@baylibre.com
2019-08-14drm/bridge: dw-hdmi-i2s: enable only the required i2s lanesJerome Brunet
Enable the i2s lanes depending on the number of channel in the stream Reviewed-by: Jonas Karlman <jonas@kwiboo.se> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190812120726.1528-8-jbrunet@baylibre.com
2019-08-14drm/bridge: dw-hdmi-i2s: reset audio fifo before applying new paramsJerome Brunet
When changing the audio hw params, reset the audio fifo to make sure any old remaining data is flushed. The databook mentions that such reset should be followed by a reset of the i2s block to make sure the samples stay aligned Reviewed-by: Jonas Karlman <jonas@kwiboo.se> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190812120726.1528-7-jbrunet@baylibre.com
2019-08-14drm/bridge: dw-hdmi-i2s: set the channel allocationJerome Brunet
setup the channel allocation provided by the generic hdmi-codec driver Reviewed-by: Jonas Karlman <jonas@kwiboo.se> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190812120726.1528-6-jbrunet@baylibre.com
2019-08-14drm/bridge: dw-hdmi-i2s: enable lpcm multi channelsJerome Brunet
Properly setup the channel count and layout in dw-hdmi i2s driver so we are not limited to 2 channels. Also correct the maximum channel reported by the DAI from 6 to 8 ch Reviewed-by: Jonas Karlman <jonas@kwiboo.se> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190812120726.1528-5-jbrunet@baylibre.com
2019-08-14drm/bridge: dw-hdmi: set channel count in the infoframesJerome Brunet
Set the number of channel in the infoframes Reviewed-by: Jonas Karlman <jonas@kwiboo.se> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190812120726.1528-4-jbrunet@baylibre.com
2019-08-14drm/bridge: dw-hdmi: move audio channel setup out of ahbJerome Brunet
Part of the channel count setup done in dw-hdmi ahb should actually be done whatever the interface providing the data. Let's move it to dw-hdmi driver instead. Reviewed-by: Jonas Karlman <jonas@kwiboo.se> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190812120726.1528-3-jbrunet@baylibre.com
2019-08-14drm/bridge: dw-hdmi-i2s: support more i2s formatJerome Brunet
The dw-hdmi-i2s supports more formats than just regular i2s. Add support for left justified, right justified and dsp modes A and B. Reviewed-by: Jonas Karlman <jonas@kwiboo.se> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190812120726.1528-2-jbrunet@baylibre.com
2019-07-31drm/bridge: dw-hdmi: Provide ddc symlink in connector sysfs directoryAndrzej Pietrasiewicz
Use the ddc pointer provided by the generic connector. Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com> Acked-by: Jernej Skrabec <jernej.skrabec@siol.net> Acked-by: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Emil Velikov <emil.velikov@collabora.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/4bcf0f154c683c9787fa34f911ebc52de6b4a7a1.1564161140.git.andrzej.p@collabora.com
2019-07-22Merge v5.3-rc1 into drm-misc-nextMaxime Ripard
Noralf needs some SPI patches in 5.3 to merge some work on tinydrm. Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-07-15Merge tag 'drm-next-2019-07-16' of git://anongit.freedesktop.org/drm/drmLinus Torvalds
Pull drm updates from Dave Airlie: "The biggest thing in this is the AMD Navi GPU support, this again contains a bunch of header files that are large. These are the new AMD RX5700 GPUs that just recently became available. New drivers: - ST-Ericsson MCDE driver - Ingenic JZ47xx SoC UAPI change: - HDR source metadata property Core: - HDR inforframes and EDID parsing - drm hdmi infoframe unpacking - remove prime sg_table caching into dma-buf - New gem vram helpers to reduce driver code - Lots of drmP.h removal - reservation fencing fix - documentation updates - drm_fb_helper_connector removed - mode name command handler rewrite fbcon: - Remove the fbcon notifiers ttm: - forward progress fixes dma-buf: - make mmap call optional - debugfs refcount fixes - dma-fence free with pending signals fix - each dma-buf gets an inode Panels: - Lots of additional panel bindings amdgpu: - initial navi10 support - avoid hw reset - HDR metadata support - new thermal sensors for vega asics - RAS fixes - use HMM rather than MMU notifier - xgmi topology via kfd - SR-IOV fixes - driver reload fixes - DC use a core bpc attribute - Aux fixes for DC - Bandwidth calc updates for DC - Clock handling refactor - kfd VEGAM support vmwgfx: - Coherent memory support changes i915: - HDR Support - HDMI i2c link - Icelake multi-segmented gamma support - GuC firmware update - Mule Creek Canyon PCH support for EHL - EHL platform updtes - move i915.alpha_support to i915.force_probe - runtime PM refactoring - VBT parsing refactoring - DSI fixes - struct mutex dependency reduction - GEM code reorg mali-dp: - Komeda driver features msm: - dsi vs EPROBE_DEFER fixes - msm8998 snapdragon 835 support - a540 gpu support - mdp5 and dpu interconnect support exynos: - drmP.h removal tegra: - misc fixes tda998x: - audio support improvements - pixel repeated mode support - quantisation range handling corrections - HDMI vendor info fix armada: - interlace support fix - overlay/video plane register handling refactor - add gamma support rockchip: - RX3328 support panfrost: - expose perf counters via hidden ioctls vkms: - enumerate CRC sources list ast: - rework BO handling mgag200: - rework BO handling dw-hdmi: - suspend/resume support rcar-du: - R8A774A1 Soc Support - LVDS dual-link mode support - Additional formats - Misc fixes omapdrm: - DSI command mode display support stm - fb modifier support - runtime PM support sun4i: - use vmap ops vc4: - binner bo binding rework v3d: - compute shader support - resync/sync fixes - job management refactoring lima: - NULL pointer in irq handler fix - scheduler default timeout virtio: - fence seqno support - trace events bochs: - misc fixes tc458767: - IRQ/HDP handling sii902x: - HDMI audio support atmel-hlcdc: - misc fixes meson: - zpos support" * tag 'drm-next-2019-07-16' of git://anongit.freedesktop.org/drm/drm: (1815 commits) Revert "Merge branch 'vmwgfx-next' of git://people.freedesktop.org/~thomash/linux into drm-next" Revert "mm: adjust apply_to_pfn_range interface for dropped token." mm: adjust apply_to_pfn_range interface for dropped token. drm/amdgpu/navi10: add uclk activity sensor drm/amdgpu: properly guard the generic discovery code drm/amdgpu: add missing documentation on new module parameters drm/amdgpu: don't invalidate caches in RELEASE_MEM, only do the writeback drm/amd/display: avoid 64-bit division drm/amdgpu/psp11: simplify the ucode register logic drm/amdgpu: properly guard DC support in navi code drm/amd/powerplay: vega20: fix uninitialized variable use drm/amd/display: dcn20: include linux/delay.h amdgpu: make pmu support optional drm/amd/powerplay: Zero initialize current_rpm in vega20_get_fan_speed_percent drm/amd/powerplay: Zero initialize freq in smu_v11_0_get_current_clk_freq drm/amd/powerplay: Use memset to initialize metrics structs drm/amdgpu/mes10.1: Fix header guard drm/amd/powerplay: add temperature sensor support for navi10 drm/amdgpu: fix scheduler timeout calc drm/amdgpu: Prepare for hmm_range_register API change (v2) ...
2019-07-01drm/bridge: dw-hdmi: Use automatic CTS generation mode when using non-AHB audioNeil Armstrong
When using an I2S source using a different clock source (usually the I2S audio HW uses dedicated PLLs, different from the HDMI PHY PLL), fixed CTS values will cause some frequent audio drop-out and glitches as reported on Amlogic, Allwinner and Rockchip SoCs setups. Setting the CTS in automatic mode will let the HDMI controller generate automatically the CTS value to match the input audio clock. The DesignWare DW-HDMI User Guide explains: For Automatic CTS generation Write "0" on the bit field "CTS_manual", Register 0x3205: AUD_CTS3 The DesignWare DW-HDMI Databook explains : If "CTS_manual" bit equals 0b this registers contains "audCTS[19:0]" generated by the Cycle time counter according to specified timing. Cc: Jernej Skrabec <jernej.skrabec@siol.net> Cc: Maxime Ripard <maxime.ripard@bootlin.com> Cc: Jonas Karlman <jonas@kwiboo.se> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Tested-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net> Tested-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190612085147.26971-1-narmstrong@baylibre.com
2019-06-24drm/bridge/synopsys: dsi: Allow VPG to be enabled via debugfsMatt Redfearn
The Synopsys MIPI DSI IP contains a video test pattern generator which is helpful in debugging video timing with connected displays. Add a debugfs directory containing files which allow the VPG to be enabled and disabled, and its orientation to be changed. Signed-off-by: Matt Redfearn <matt.redfearn@thinci.com> Tested-by: Yannick Fertré <yannick.fertre@st.com> Reviewed-by: Philippe Cornu <philippe.cornu@st.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190430081646.23845-1-matt.redfearn@thinci.com
2019-06-19treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500Thomas Gleixner
Based on 2 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation # extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference in 4122 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Enrico Weigelt <info@metux.net> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-19Merge v5.2-rc5 into drm-nextDaniel Vetter
Maarten needs -rc4 backmerged so he can pull in the fbcon notifier removal topic branch into drm-misc-next. Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2019-06-12drm/bridge/synopsys: dsi: add power on/off optional phy opsYannick Fertré
Add power on & off optional physical operation functions, helpful to program specific registers of the DSI physical part. Signed-off-by: Yannick Fertré <yannick.fertre@st.com> Reviewed-by: Philippe Cornu <philippe.cornu@st.com> Tested-by: Philippe Cornu <philippe.cornu@st.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/1558952499-15418-2-git-send-email-yannick.fertre@st.com
2019-06-11drm: bridge: dw-hdmi: Add hook for resumeDouglas Anderson
On Rockchip rk3288-based Chromebooks when you do a suspend/resume cycle: 1. You lose the ability to detect an HDMI device being plugged in. 2. If you're using the i2c bus built in to dw_hdmi then it stops working. Let's add a hook to the core dw-hdmi driver so that we can call it in dw_hdmi-rockchip in the next commit. NOTE: the exact set of steps I've done here in resume come from looking at the normal dw_hdmi init sequence in upstream Linux plus the sequence that we did in downstream Chrome OS 3.14. Testing show that it seems to work, but if an extra step is needed or something here is not needed we could improve it. As part of this change we'll refactor the hardware init bits of dw-hdmi to happen all in one function and all at the same time. Since we need to init the interrupt mutes before we request the IRQ, this means moving the hardware init earlier in the function, but there should be no problems with that. Also as part of this we now unconditionally init the "i2c" parts of dw-hdmi, but again that ought to be fine. Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190604204207.168085-1-dianders@chromium.org
2019-06-10drm/bridge/synopsys: dw-hdmi: Fix unwedge crash when no pinctrl entriesDouglas Anderson
In commit 50f9495efe30 ("drm/bridge/synopsys: dw-hdmi: Add "unwedge" for ddc bus") I stupidly used IS_ERR() to check for whether we have an "unwedge" pinctrl state even though on most flows through the driver the unwedge state will just be NULL. Fix it so that we consistently use NULL for no unwedge state. Fixes: 50f9495efe30 ("drm/bridge/synopsys: dw-hdmi: Add "unwedge" for ddc bus") Cc: Douglas Anderson <dianders@chromium.org> Cc: Sean Paul <seanpaul@chromium.org> Cc: Andrzej Hajda <a.hajda@samsung.com> Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Neil Armstrong <narmstrong@baylibre.com> Cc: Jonas Karlman <jonas@kwiboo.se> Cc: Jernej Skrabec <jernej.skrabec@siol.net> Cc: Sam Ravnborg <sam@ravnborg.org> Reported-by: Erico Nunes <nunes.erico@gmail.com> Signed-off-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190610175234.196844-1-dianders@chromium.org
2019-06-05drm/bridge/synopsys: dw-hdmi: Add "unwedge" for ddc busDouglas Anderson
See the PhD thesis in the comments in this patch for details, but to summarize this adds a hacky "unwedge" feature to the dw_hdmi i2c bus to workaround what appears to be a hardware errata. This relies on a pinctrl entry to help change around muxing to perform the unwedge. NOTE that the specific TV this was tested on was the "Samsung UN40HU6950FXZA" and the specific port was the "STB" port. Signed-off-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190502225336.206885-2-dianders@chromium.org
2019-05-30treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 152Thomas Gleixner
Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 3029 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-28Merge remote-tracking branch 'drm/drm-next' into drm-misc-nextMaarten Lankhorst
This picks up rc2 for us as well. Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
2019-05-26drm/bridge: drop drmP.h usageSam Ravnborg
Drop use of the deprecated drmP.h header file. While touching the list of include files: - Divide include files in blocks of linux/* drm/* etc. - Sort individual blocks of include files - Remove duplicated header file v2: - Be consistent in the order of the include blocks (Laurent) Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Laurent Pinchart <Laurent.pinchart@ideasonboard.com> Cc: Andrzej Hajda <a.hajda@samsung.com> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Peter Senna Tschudin <peter.senna@gmail.com> Cc: Martin Donnelly <martin.donnelly@ge.com> Cc: Martyn Welch <martyn.welch@collabora.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20190519183636.19588-1-sam@ravnborg.org
2019-05-21treewide: Add SPDX license identifier - Makefile/KconfigThomas Gleixner
Add SPDX license identifiers to all Make/Kconfig files which: - Have no license information of any form These files fall under the project license, GPL v2 only. The resulting SPDX license identifier is: GPL-2.0-only Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-25drm/bridge: dw-hdmi: fix SCDC configuration for ddc-i2c-busJonas Karlman
When ddc-i2c-bus property is used, a NULL pointer dereference is reported: [ 31.041669] Unable to handle kernel NULL pointer dereference at virtual address 00000008 [ 31.041671] pgd = 4d3c16f6 [ 31.041673] [00000008] *pgd=00000000 [ 31.041678] Internal error: Oops: 5 [#1] SMP ARM [ 31.041711] Hardware name: Rockchip (Device Tree) [ 31.041718] PC is at i2c_transfer+0x8/0xe4 [ 31.041721] LR is at drm_scdc_read+0x54/0x84 [ 31.041723] pc : [<c073273c>] lr : [<c05926c4>] psr: 280f0013 [ 31.041725] sp : edffdad0 ip : 5ccb5511 fp : 00000058 [ 31.041727] r10: 00000780 r9 : edf91608 r8 : c11b0f48 [ 31.041728] r7 : 00000438 r6 : 00000000 r5 : 00000000 r4 : 00000000 [ 31.041730] r3 : edffdae7 r2 : 00000002 r1 : edffdaec r0 : 00000000 [ 31.041908] [<c073273c>] (i2c_transfer) from [<c05926c4>] (drm_scdc_read+0x54/0x84) [ 31.041913] [<c05926c4>] (drm_scdc_read) from [<c0592858>] (drm_scdc_set_scrambling+0x30/0xbc) [ 31.041919] [<c0592858>] (drm_scdc_set_scrambling) from [<c05cc0f4>] (dw_hdmi_update_power+0x1440/0x1610) [ 31.041926] [<c05cc0f4>] (dw_hdmi_update_power) from [<c05cc574>] (dw_hdmi_bridge_enable+0x2c/0x70) [ 31.041932] [<c05cc574>] (dw_hdmi_bridge_enable) from [<c05aed48>] (drm_bridge_enable+0x24/0x34) [ 31.041938] [<c05aed48>] (drm_bridge_enable) from [<c0591060>] (drm_atomic_helper_commit_modeset_enables+0x114/0x220) [ 31.041943] [<c0591060>] (drm_atomic_helper_commit_modeset_enables) from [<c05c3fe0>] (rockchip_atomic_helper_commit_tail_rpm+0x28/0x64) hdmi->i2c may not be set when ddc-i2c-bus property is used in device tree. Fix this by using hdmi->ddc as the i2c adapter when calling drm_scdc_*(). Also report that SCDC is not supported when there is no DDC bus. Fixes: 264fce6cc2c1 ("drm/bridge: dw-hdmi: Add SCDC and TMDS Scrambling support") Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/VE1PR03MB59031814B5BCAB2152923BDAAC210@VE1PR03MB5903.eurprd03.prod.outlook.com
2019-04-12drm: bridge: dw-hdmi: Fix overflow workaround for Rockchip SoCsJonas Karlman
The Rockchip RK3288 SoC (v2.00a) and RK3328/RK3399 SoCs (v2.11a) have also been identified as needing this workaround with a single iteration. Fixes: be41fc55f1aa ("drm: bridge: dw-hdmi: Handle overflow workaround based on device version") Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Tested-by: Heiko Stueber <heiko@sntech.de> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/AM3PR03MB0966818FAAAE6192FF4ED11AAC7D0@AM3PR03MB0966.eurprd03.prod.outlook.com
2019-03-25drm/bridge: dw-hdmi: disable SCDC configuration for invalid setupsNeil Armstrong
This patch is an attempt to limit HDMI 2.0 SCDC setup when : - the SoC embeds an HDMI 1.4 only controller - the EDID supports SCDC but not scrambling - the EDID supports SCDC scrambling but not for low TMDS bit rates, while only supporting low TMDS bit rates This to avoid communicating with the SCDC DDC slave uncessary, and setting the DW-HDMI TMDS Scrambler setup when not supported by the underlying hardware. Reported-by: Rob Herring <robh@kernel.org> Fixes: 264fce6cc2c1 ("drm/bridge: dw-hdmi: Add SCDC and TMDS Scrambling support") Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Tested-by: Rob Herring <robh@kernel.org> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190315095414.28520-1-narmstrong@baylibre.com
2019-03-08Merge tag 'drm-next-2019-03-06' of git://anongit.freedesktop.org/drm/drmLinus Torvalds
Pull drm updates from Dave Airlie: "This is the main drm pull request for the 5.1 merge window. The big changes I'd highlight are: - nouveau has HMM support now, there is finally an in-tree user so we can quieten down the rip it out people. - i915 now enables fastboot by default on Skylake+ - Displayport Multistream support has been refactored and should hopefully be more reliable. Core: - header cleanups aiming towards removing drmP.h - dma-buf fence seqnos to 64-bits - common helper for DP mst hotplug for radeon,i915,amdgpu + new refcounting scheme - MST i2c improvements - drm_syncobj_cb removal - ARM FB compression fourcc - P010 + P016 fourcc - allwinner tiled format modifier - i2c over aux I2C_M_STOP support - DRM_AUTH handling fixes TTM: - ref/unref renaming New driver: - ARM komeda display driver scheduler: - refactor mirror list handling - rework hw fence processing - 0 run queue entity fix bridge: - TI DS90C185 LVDS bridge - thc631lvdm83d bridge improvements - cadence + allwinner DSI ported to generic phy panels: - Sitronix ST7701 panel - Kingdisplay KD097D04 - LeMaker BL035-RGB-002 - PDA 91-00156-A0 - Innolux EE101IA-01D i915: - Enable fastboot by default on SKL+/VLV/CHV - Export RPCS configuration for ICL media driver - Coffelake PCI ID - CNL clocks setup fixes - ACPI/PMIC support for MIPI/DSI - Per-engine WA init for all engines - Shrinker locking fixes - Kerneldoc updates - Lots of ring improvements and reset fixes - Coffeelake GVT Support - VFIO GVT EDID Region support - runtime PM wakeref tracking - ILK->IVB primary plane enable delays - userptr mutex locking fixes - DSI fixes - LVDS/TV cleanups - HW readout fixes - LUT robustness fixes - ICL display and watermark fixes - gem mmap race fix amdgpu: - add scheduled dependencies interface - DCC on scanout surfaces - vega10/20 BACO support - Multiple IH rings on soc15 - XGMI locking fixes - DC i2c/aux cleanups - runtime SMU debug interface - Kexec improvmeents - SR-IOV fixes - DC freesync + ABM fixes - GDS fixes - GPUVM fixes - vega20 PCIE DPM switching fixes - Context priority handling fixes radeon: - fix missing break in evergreen parser nouveau: - SVM support via HMM msm: - QCOM Compressed modifier support exynos: - s5pv210 rotator support imx: - zpos property support - pending update fixes v3d: - cache flush improvments vc4: - reflection support - HDMI overscan support tegra: - CEC refactoring - HDMI audio fixes - Tegra186 prep work - SOR crossbar device tree fixes sun4i: - implicit fencing support - YUV and scalar support improvements - A23 support - tiling fixes atmel-hlcdc: - clipping and rotation property fixes qxl: - BO and PRIME improvements - generic fbdev emulation dw-hdmi: - HDMI 2.0 2160p - YUV420 ouput rockchip: - implicit fencing support - reflection proerties virtio-gpu: - use generic fbdev emulation tilcdc: - cpufreq vs crtc init fix rcar-du: - R8A774C0 support - D3/E3 RGB output routing fixes and DPAD0 support - RA87744 LVDS support bochs: - atomic and generic fbdev emulation - ID mismatch error on bochs load meson: - remove firmware fbs" * tag 'drm-next-2019-03-06' of git://anongit.freedesktop.org/drm/drm: (1130 commits) drm/amd/display: Use vrr friendly pageflip throttling in DC. drm/imx: only send commit done event when all state has been applied drm/imx: allow building under COMPILE_TEST drm/imx: imx-tve: depend on COMMON_CLK drm/imx: ipuv3-plane: add zpos property drm/imx: ipuv3-plane: add function to query atomic update status gpu: ipu-v3: prg: add function to get channel configure status gpu: ipu-v3: pre: add double buffer status readback drm/amdgpu: Bump amdgpu version for context priority override. drm/amdgpu/powerplay: fix typo in BACO header guards drm/amdgpu/powerplay: fix return codes in BACO code drm/amdgpu: add missing license on baco files drm/bochs: Fix the ID mismatch error drm/nouveau/dmem: use dma addresses during migration copies drm/nouveau/dmem: use physical vram addresses during migration copies drm/nouveau/dmem: extend copy function to allow direct use of physical addresses drm/nouveau/svm: new ioctl to migrate process memory to GPU memory drm/nouveau/dmem: device memory helpers for SVM drm/nouveau/svm: initial support for shared virtual memory drm/nouveau: prepare for enabling svm with existing userspace interfaces ...
2019-02-01drm/bridge: dw-hdmi: add support for YUV420 outputNeil Armstrong
In order to support the HDMI2.0 YUV420 display modes, this patch adds support for the YUV420 TMDS Clock divided by 2 and the controller passthrough mode. YUV420 Synopsys PHY support will need some specific configuration table to support theses modes. This patch is based on work from Zheng Yang <zhengyang@rock-chips.com> in the Rockchip Linux 4.4 BSP at [1] [1] https://github.com/rockchip-linux/kernel/tree/release-4.4 Cc: Zheng Yang <zhengyang@rock-chips.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Tested-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/1549022873-40549-5-git-send-email-narmstrong@baylibre.com
2019-02-01drm/bridge: dw-hdmi: Add SCDC and TMDS Scrambling supportNeil Armstrong
Add support for SCDC Setup for TMDS Clock > 3.4GHz and enable TMDS Scrambling when supported or mandatory. This patch also adds an helper to setup the control bit to support the high TMDS Bit Period/TMDS Clock-Period Ratio as required with TMDS Clock > 3.4GHz for HDMI2.0 3840x2160@60/50 modes. These changes were based on work done by Huicong Xu <xhc@rock-chips.com> and Nickey Yang <nickey.yang@rock-chips.com> to support HDMI2.0 modes on the Rockchip 4.4 BSP kernel at [1] [1] https://github.com/rockchip-linux/kernel/tree/release-4.4 Cc: Nickey Yang <nickey.yang@rock-chips.com> Cc: Huicong Xu <xhc@rock-chips.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Tested-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/1549022873-40549-2-git-send-email-narmstrong@baylibre.com
2019-01-24drm: Split out drm_probe_helper.hDaniel Vetter
Having the probe helper stuff (which pretty much everyone needs) in the drm_crtc_helper.h file (which atomic drivers should never need) is confusing. Split them out. To make sure I actually achieved the goal here I went through all drivers. And indeed, all atomic drivers are now free of drm_crtc_helper.h includes. v2: Make it compile. There was so much compile fail on arm drivers that I figured I'll better not include any of the acks on v1. v3: Massive rebase because i915 has lost a lot of drmP.h includes, but not all: Through drm_crtc_helper.h > drm_modeset_helper.h -> drmP.h there was still one, which this patch largely removes. Which means rolling out lots more includes all over. This will also conflict with ongoing drmP.h cleanup by others I expect. v3: Rebase on top of atomic bochs. v4: Review from Laurent for bridge/rcar/omap/shmob/core bits: - (re)move some of the added includes, use the better include files in other places (all suggested from Laurent adopted unchanged). - sort alphabetically v5: Actually try to sort them, and while at it, sort all the ones I touch. v6: Rebase onto i915 changes. v7: Rebase once more. Acked-by: Harry Wentland <harry.wentland@amd.com> Acked-by: Sam Ravnborg <sam@ravnborg.org> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org> Acked-by: Jani Nikula <jani.nikula@intel.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Acked-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com> Acked-by: CK Hu <ck.hu@mediatek.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Acked-by: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Liviu Dudau <liviu.dudau@arm.com> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Cc: linux-arm-kernel@lists.infradead.org Cc: virtualization@lists.linux-foundation.org Cc: etnaviv@lists.freedesktop.org Cc: linux-samsung-soc@vger.kernel.org Cc: intel-gfx@lists.freedesktop.org Cc: linux-mediatek@lists.infradead.org Cc: linux-amlogic@lists.infradead.org Cc: linux-arm-msm@vger.kernel.org Cc: freedreno@lists.freedesktop.org Cc: nouveau@lists.freedesktop.org Cc: spice-devel@lists.freedesktop.org Cc: amd-gfx@lists.freedesktop.org Cc: linux-renesas-soc@vger.kernel.org Cc: linux-rockchip@lists.infradead.org Cc: linux-stm32@st-md-mailman.stormreply.com Cc: linux-tegra@vger.kernel.org Cc: xen-devel@lists.xen.org Link: https://patchwork.freedesktop.org/patch/msgid/20190117210334.13234-1-daniel.vetter@ffwll.ch
2019-01-18Merge tag 'drm-misc-next-2019-01-16' of ↵Dave Airlie
git://anongit.freedesktop.org/drm/drm-misc into drm-next drm-misc-next for 5.1: UAPI Changes: - New fourcc identifier for ARM Framebuffer Compression v1.3 Cross-subsystem Changes: Core Changes: - Reorganisation of drm_device and drm_framebuffer headers - Cleanup of the drmP inclusion - Fix leaks in the fb-helpers - Allow for depth different from bpp in fb-helper fbdev emulation - Remove drm_mode_object from drm_display_mode Driver Changes: - Add reflection properties to rockchip - a bunch of fixes for virtio - a bunch of fixes for dp_mst and drivers using it, and introduction of a new refcounting scheme - Convertion of bochs to atomic and generic fbdev emulation - Allow meson to remove the firmware framebuffers [airlied: patch rcar-du to add drm_modes.h] Signed-off-by: Dave Airlie <airlied@redhat.com> From: Maxime Ripard <maxime.ripard@bootlin.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190116200428.u2n4jbk4mzza7n6e@flea
2019-01-15drm: bridge: dw-hdmi: Remove superfluous snd_pcm_suspend*() callsTakashi Iwai
The call of snd_pcm_suspend_all() & co became superfluous since we call it in the PCM PM ops. Let's remove them. Reviewed-by: Jaroslav Kysela <perex@perex.cz> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2019-01-14drm: bridge: Constify mode arguments to bridge .mode_set() operationLaurent Pinchart
The mode and ajusted_mode passed to the bridge .mode_set() operation should never be modified by the bridge (and are not in any of the existing bridge drivers). Make them const to make this clear. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2019-01-10drm/edid: Pass connector to AVI infoframe functionsVille Syrjälä
Make life easier for drivers by simply passing the connector to drm_hdmi_avi_infoframe_from_display_mode() and drm_hdmi_avi_infoframe_quant_range(). That way drivers don't need to worry about is_hdmi2_sink mess. v2: Make is_hdmi2_sink() return true for sil-sii8620 Adapt to omap/vc4 changes Cc: Alex Deucher <alexander.deucher@amd.com> Cc: "Christian König" <christian.koenig@amd.com> Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com> Cc: Archit Taneja <architt@codeaurora.org> Cc: Andrzej Hajda <a.hajda@samsung.com> Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com> Cc: Inki Dae <inki.dae@samsung.com> Cc: Joonyoung Shim <jy0922.shim@samsung.com> Cc: Seung-Woo Kim <sw0312.kim@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Cc: Russell King <linux@armlinux.org.uk> Cc: CK Hu <ck.hu@mediatek.com> Cc: Philipp Zabel <p.zabel@pengutronix.de> Cc: Rob Clark <robdclark@gmail.com> Cc: Ben Skeggs <bskeggs@redhat.com> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Cc: Sandy Huang <hjc@rock-chips.com> Cc: "Heiko Stübner" <heiko@sntech.de> Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org> Cc: Vincent Abriou <vincent.abriou@st.com> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Eric Anholt <eric@anholt.net> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Ilia Mirkin <imirkin@alum.mit.edu> Cc: amd-gfx@lists.freedesktop.org Cc: linux-arm-msm@vger.kernel.org Cc: freedreno@lists.freedesktop.org Cc: nouveau@lists.freedesktop.org Cc: linux-tegra@vger.kernel.org Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Acked-by: Thierry Reding <treding@nvidia.com> Acked-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190108172828.15184-1-ville.syrjala@linux.intel.com
2019-01-09drm: remove include of drmP.h from bridge/dw_hdmi.hSam Ravnborg
drmP.h is an relic from the days when there was a single header file. To enable the removal of drmP.h from all users drop include of drmP.h from bridge/dw_hdmi.h. A few files relied on the file included in drmP.h - add explicit include statements or forward declarations to these files. Build tested with arm and x86. v2: - prefer forward declarations when possible (Laurent Pinchart) - sort include files (Laurent Pinchart) Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Archit Taneja <architt@codeaurora.org> Cc: Andrzej Hajda <a.hajda@samsung.com> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Neil Armstrong <narmstrong@baylibre.com> Cc: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20190108192939.15255-7-sam@ravnborg.org
generated by cgit (git 2.34.1) at 2025-04-17 15:49:55 +0000