summaryrefslogtreecommitdiff
path: root/drivers/gpu/drm/bridge
AgeCommit message (Collapse)Author
2017-01-18drm: bridge: dw-hdmi: Define and use macros for PHY register addressesLaurent Pinchart
Replace the hardcoded register address numerical values with macros to clarify the code. This change has been tested by comparing the assembly code before and after the change. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Jose Abreu <joabreu@synopsys.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-18-laurent.pinchart+renesas@ideasonboard.com
2017-01-18drm: bridge: dw-hdmi: Detect PHY type at runtimeLaurent Pinchart
Detect the PHY type and use it to handle the PHY type-specific SVSRET signal. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-17-laurent.pinchart+renesas@ideasonboard.com
2017-01-18drm: bridge: dw-hdmi: Handle overflow workaround based on device versionLaurent Pinchart
Use the device version queried at runtime instead of the device type provided through platform data to handle the overflow workaround. This will make support of other SoCs integrating the same HDMI TX controller version easier. Among the supported platforms only i.MX6DL and i.MX6Q have been identified as needing the workaround. Disabling it on Rockchip RK3288 (which integrates a v2.00a controller) didn't produce any error or artifact. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Jose Abreu <joabreu@synopsys.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-16-laurent.pinchart+renesas@ideasonboard.com
2017-01-18drm: bridge: dw-hdmi: Detect AHB audio DMA using correct registerLaurent Pinchart
Bit 0 in CONFIG1_ID tells whether the IP core uses an AHB slave interface for control. The correct way to identify AHB audio DMA support is through bit 1 in CONFIG3_ID. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Jose Abreu <joabreu@synopsys.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-15-laurent.pinchart+renesas@ideasonboard.com
2017-01-18drm: bridge: dw-hdmi: Reject invalid product IDsLaurent Pinchart
The DWC HDMI TX can be recognized by the two product identification registers. If the registers don't read as expect the IP will be very different than what the driver has been designed for, or will be misconfigured in a way that makes it non-operational (invalid memory address, incorrect clocks, ...). We should reject this situation with an error. While this isn't critical for proper operation with supported IPs at the moment, the driver will soon gain automatic device-specific handling based on runtime device identification. This change makes it easier to implement that without having to default to a random guess in case the device can't be identified. While at it print a readable version number in the device identification message instead of raw register values. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Jose Abreu <joabreu@synopsys.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-14-laurent.pinchart+renesas@ideasonboard.com
2017-01-18drm: bridge: dw-hdmi: Rename CONF0 SPARECTRL bit to SVSRETLaurent Pinchart
The bit is documented in a Rockchip BSP as #define m_SVSRET_SIG (1 << 5) /* depend on PHY_MHL_COMB0=1 */ This is confirmed by a Renesas platform, which uses a 2.0 DWC HDMI TX as the RK3288. Rename the bit accordingly. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Jose Abreu <joabreu@synopsys.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-13-laurent.pinchart+renesas@ideasonboard.com
2017-01-18drm: bridge: dw-hdmi: Remove PHY configuration resolution parameterKieran Bingham
The current code hard codes the call of hdmi_phy_configure() to be 8bpp and provides extraneous error checking to verify that this hardcoded value is correct. Simplify the implementation by removing the argument. Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Jose Abreu <joabreu@synopsys.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-12-laurent.pinchart+renesas@ideasonboard.com
2017-01-18drm: bridge: dw-hdmi: Implement DRM bridge registrationLaurent Pinchart
As an option for drivers not based on the component framework, register the bridge with the DRM core with the DRM bridge API. Existing drivers based on dw_hdmi_bind() and dw_hdmi_unbind() are not affected as those functions are preserved with their current behaviour. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Jose Abreu <joabreu@synopsys.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-11-laurent.pinchart+renesas@ideasonboard.com
2017-01-18drm: bridge: dw-hdmi: Create connector in the bridge attach operationLaurent Pinchart
The DRM device is not guaranteed by the bridge API to be available before the attach callback. The driver performs properly at the moment as it doesn't use the drm_bridge_add() registration method. As this will be changed later, move connector creation to attach time to ensure compatibility with the API. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Jose Abreu <joabreu@synopsys.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-10-laurent.pinchart+renesas@ideasonboard.com
2017-01-18drm: bridge: dw-hdmi: Reorder functions to prepare for next commitLaurent Pinchart
The next commit will reference structures and functions in a way that currently requires forward declarations. Reorder the functions to avoid that. No functional change to the code is performed. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Jose Abreu <joabreu@synopsys.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-9-laurent.pinchart+renesas@ideasonboard.com
2017-01-18drm: bridge: dw-hdmi: Move IRQ and IO resource allocation to common codeLaurent Pinchart
There's no need to duplicate identical code in multiple drivers (two at the moment, one more to come soon). Move it to the dw-hdmi core where it can be shared. If resource allocation ever becomes device-specific later we'll always have the option of splitting it out again. While it at pass the platform device to the bind function to avoid having to cast struct device to struct platform_device. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Jose Abreu <joabreu@synopsys.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-8-laurent.pinchart+renesas@ideasonboard.com
2017-01-18drm: bridge: dw-hdmi: Don't forward HPD events to DRM core before attachLaurent Pinchart
Hotplug events should only be forwarded to the DRM core by the interrupt handler when the bridge has been attached, otherwise the DRM device pointer will be NULL, resulting in a crash. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Jose Abreu <joabreu@synopsys.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-7-laurent.pinchart+renesas@ideasonboard.com
2017-01-18drm: bridge: dw-hdmi: Remove encoder field from struct dw_hdmiLaurent Pinchart
The field isn't needed, remove it. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Jose Abreu <joabreu@synopsys.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-6-laurent.pinchart+renesas@ideasonboard.com
2017-01-18drm: bridge: dw-hdmi: Embed drm_bridge in struct dw_hdmiLaurent Pinchart
The drm_bridge instance is always needed, there's no point in allocating it separately. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Jose Abreu <joabreu@synopsys.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-5-laurent.pinchart+renesas@ideasonboard.com
2017-01-18drm: bridge: dw-hdmi: Remove unused function parameterKieran Bingham
The 'prep' parameter passed to hdmi_phy_configure() is useless. It is hardcoded as 0, and if set, simply prevents the configure function from executing. Remove it. Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Jose Abreu <joabreu@synopsys.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-4-laurent.pinchart+renesas@ideasonboard.com
2017-01-18drm: bridge: dw-hdmi: Remove unneeded arguments to bind/unbind functionsLaurent Pinchart
The master argument isn't used. The data argument, a void pointer, is used by the bind function only where it's cast to a drm_device pointer, which can easily be obtained from the encoder argument instead. Remove them. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Jose Abreu <joabreu@synopsys.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-3-laurent.pinchart+renesas@ideasonboard.com
2017-01-18drm: bridge: dw-hdmi: Merge __hdmi_phy_i2c_write and hdmi_phy_i2c_writeLaurent Pinchart
The latter is just an int wrapper around the former void function that unconditionally returns 0. As the return value is never checked, merge the two functions into one. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Jose Abreu <joabreu@synopsys.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-2-laurent.pinchart+renesas@ideasonboard.com
2017-01-17drm/bridge: adv7511: Initialize regulatorsArchit Taneja
Maintain a table of regulator names expected by ADV7511 and ADV7533. Use regulator_bulk_* api to configure these. Initialize and enable the regulators during probe itself. Controlling these dynamically is left for later. Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/1484117547-26417-3-git-send-email-architt@codeaurora.org
2017-01-09drm/bridge: analogix dp: Fix runtime PM state on driver bindMarek Szyprowski
Analogix_dp_bind() can be called from component framework, which doesn't guarantee proper runtime PM state of the device during bind operation, so ensure that device is runtime active before doing any register access. This ensures that the power domain, to which DP module belongs, is turned on. While at it, also fix the unbalanced call to phy_power_on() in analogix_dp_bind() function. This patch solves the following kernel oops on Samsung Exynos5250 Snow board: Unhandled fault: imprecise external abort (0x406) at 0x00000000 pgd = c0004000 [00000000] *pgd=00000000 Internal error: : 406 [#1] PREEMPT SMP ARM Modules linked in: CPU: 0 PID: 75 Comm: kworker/0:2 Not tainted 4.9.0 #1046 Hardware name: SAMSUNG EXYNOS (Flattened Device Tree) Workqueue: events deferred_probe_work_func task: ee272300 task.stack: ee312000 PC is at analogix_dp_enable_sw_function+0x18/0x2c LR is at analogix_dp_init_dp+0x2c/0x50 ... [<c03fcb38>] (analogix_dp_enable_sw_function) from [<c03fa9c4>] (analogix_dp_init_dp+0x2c/0x50) [<c03fa9c4>] (analogix_dp_init_dp) from [<c03fab6c>] (analogix_dp_bind+0x184/0x42c) [<c03fab6c>] (analogix_dp_bind) from [<c03fdb84>] (component_bind_all+0xf0/0x218) [<c03fdb84>] (component_bind_all) from [<c03ed64c>] (exynos_drm_load+0x134/0x200) [<c03ed64c>] (exynos_drm_load) from [<c03d5058>] (drm_dev_register+0xa0/0xd0) [<c03d5058>] (drm_dev_register) from [<c03d66b8>] (drm_platform_init+0x58/0xb0) [<c03d66b8>] (drm_platform_init) from [<c03fe0c4>] (try_to_bring_up_master+0x14c/0x188) [<c03fe0c4>] (try_to_bring_up_master) from [<c03fe188>] (component_add+0x88/0x138) [<c03fe188>] (component_add) from [<c0403a38>] (platform_drv_probe+0x50/0xb0) [<c0403a38>] (platform_drv_probe) from [<c0402470>] (driver_probe_device+0x1f0/0x2a8) [<c0402470>] (driver_probe_device) from [<c0400a54>] (bus_for_each_drv+0x44/0x8c) [<c0400a54>] (bus_for_each_drv) from [<c04021f8>] (__device_attach+0x9c/0x100) [<c04021f8>] (__device_attach) from [<c04018e8>] (bus_probe_device+0x84/0x8c) [<c04018e8>] (bus_probe_device) from [<c0401d1c>] (deferred_probe_work_func+0x60/0x8c) [<c0401d1c>] (deferred_probe_work_func) from [<c012fc14>] (process_one_work+0x120/0x318) [<c012fc14>] (process_one_work) from [<c012fe34>] (process_scheduled_works+0x28/0x38) [<c012fe34>] (process_scheduled_works) from [<c0130048>] (worker_thread+0x204/0x4ac) [<c0130048>] (worker_thread) from [<c01352c4>] (kthread+0xd8/0xf4) [<c01352c4>] (kthread) from [<c0107978>] (ret_from_fork+0x14/0x3c) Code: e59035f0 e5935018 f57ff04f e3c55001 (f57ff04e) ---[ end trace 3d1d0d87796de344 ]--- Reviewed-by: Sean Paul <seanpaul@chromium.org> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/1483091866-1088-1-git-send-email-m.szyprowski@samsung.com
2016-12-18drm: bridge: Link encoder and bridge in core codeLaurent Pinchart
Instead of linking encoders and bridges in every driver (and getting it wrong half of the time, as many drivers forget to set the drm_bridge encoder pointer), do so in core code. The drm_bridge_attach() function needs the encoder and optional previous bridge to perform that task, update all the callers. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by: Stefan Agner <stefan@agner.ch> # For DCU Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> # For atmel-hlcdc Acked-by: Vincent Abriou <vincent.abriou@st.com> # For STI Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> # For sun4i Acked-by: Xinliang Liu <z.liuxinliang@hisilicon.com> # For hisilicon Acked-by: Jyri Sarha <jsarha@ti.com> # For tilcdc Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/1481709550-29226-4-git-send-email-laurent.pinchart+renesas@ideasonboard.com
2016-12-15drm/bridge: analogix_dp: set the DPCD600 during disabling PSRCaesar Wang
It looks like the BOE panel FW didn't ack the DPCD600 signal from the host device, this will cause the panel to hang on the startup display. The root cause is that we use the fast link mode when we enter and exit PSR, the issue is gone if we switch from the fast link to main link mode. Signed-off-by: Caesar Wang <wxt@rock-chips.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/1481338159-7189-1-git-send-email-wxt@rock-chips.com
2016-12-14drm: bridge: add support for TI ths8135Bartosz Golaszewski
THS8135 is a configurable video DAC, but no configuration is actually necessary to make it work. For now use the dumb-vga-dac driver to support it. Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/1481623759-12786-4-git-send-email-bgolaszewski@baylibre.com
2016-12-07drm/bridge: analogix: Don't return -EINVAL when panel doesn't support PSRzain wang
We will ignored PSR setting if panel not support it. So, in this case, we should return from analogix_dp_enable/disable_psr() without any error code. Let's retrun 0 instead of -EINVAL when panel not support PSR in analogix_dp_enable/disable_psr(). Signed-off-by: zain wang <wzz@rock-chips.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/1481072253-8917-1-git-send-email-wzz@rock-chips.com
2016-12-06Merge remote-tracking branch 'airlied/drm-next' into drm-misc-nextDaniel Vetter
Backmerge v4.9-rc8 to get at commit e94bd1736f1f60e916a85a80c0b0ebeaae36cce5 Author: Michel Dänzer <michel.daenzer@amd.com> Date: Wed Nov 30 17:30:01 2016 +0900 drm: Don't call drm_for_each_crtc with a non-KMS driver so I can apply Michel's follow-up patch. Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
2016-12-01drm: Make the connector .detect() callback optionalLaurent Pinchart
Many drivers (21 to be exact) create connectors that are always connected (for instance to an LVDS or DSI panel). Instead of forcing them to implement a dummy .detect() handler, make the callback optional and consider the connector as always connected in that case. Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Jyri Sarha <jsarha@ti.com> Acked-by: Jani Nikula <jani.nikula@intel.com> Acked-by: Philipp Zabel <p.zabel@pengutronix.de> Acked-by: Vincent Abriou <vincent.abriou@st.com> Acked-by: Alexey Brodkin <abrodkin@synopsys.com> Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> [seanpaul fixed small conflict in rcar-du/rcar_du_lvdscon.c] Signed-off-by: Sean Paul <seanpaul@chromium.org>
2016-12-01drm/bridge: tc358767: don't warn if display side ASSR enable failsLucas Stach
ASSR is an optional feature, so it's a valid operating condition for the display to reject ASSR enable. Demote the warning to the debug level. Acked-by: Philipp Zabel <p.zabel@pengutronix.de> Acked-by:Andrey Gusakov <andrey.gusakov@cogentembedded.com> Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/20161130114810.3245-1-l.stach@pengutronix.de
2016-12-01Merge tag 'tilcdc-4.10' of https://github.com/jsarha/linux into drm-nextDave Airlie
tilcdc changes for v4.10 * tag 'tilcdc-4.10' of https://github.com/jsarha/linux: (23 commits) drm/tilcdc: fix parsing of some DT properties drm/tilcdc: Enable frame done irq and functionality for LCDC rev 1 drm/tilcdc: Configure video mode to HW in enable() not in mode_set_nofb() drm/tilcdc: Load palette at the end of mode_set_nofb() drm/tilcdc: Add timeout wait for palette loading to complete drm/tilcdc: Enable palette loading for revision 2 LCDC too drm/tilcdc: Fix load mode bit-field setting in tilcdc_crtc_enable() drm/tilcdc: Add tilcdc_write_mask() to tilcdc_regs.h drm/tilcdc: Fix tilcdc_crtc_create() return value handling drm/tilcdc: implement palette loading for rev1 drm/tilcdc: Enable sync lost error and recovery handling for rev 1 LCDC drm/tilcdc: Add drm bridge support for attaching drm bridge drivers drm/bridge: Add ti-tfp410 DVI transmitter driver dt-bindings: Move "ti,tfp410.txt" from display/ti to display/bridge drm/tilcdc: Recover from sync lost error flood by resetting the LCDC drm/tilcdc: Fix race from forced shutdown of crtc in unload drm/tilcdc: Use unload to handle initialization failures drm/tilcdc: Stop using struct drm_driver load() callback drm/tilcdc: Remove obsolete drm_connector_register() calls drm/tilcdc: Correct misspelling in error message ...
2016-11-30drm/bridge: Add ti-tfp410 DVI transmitter driverJyri Sarha
Add very basic ti-tfp410 DVI transmitter driver. The only feature separating this from a completely dummy bridge is the EDID read support trough DDC I2C. Even that functionality should be in a separate generic connector driver. However, because of missing DRM infrastructure support the connector is implemented within the bridge driver. Some tfp410 HW specific features may be added later if needed, because there is a set of registers behind i2c if it is connected. This implementation is tested against my new tilcdc bridge support and it works with BeagleBone DVI-D Cape Rev A3. A DT binding document is also updated. Signed-off-by: Jyri Sarha <jsarha@ti.com> Acked-by: Rob Herring <robh@kernel.org>
2016-11-29drm/bridge: adv7511: Enable the audio data and clock pads on adv7533Srinivas Kandagatla
This patch enables the Audio Data and Clock pads to the adv7533 bridge. Without this patch audio can not be played. Cc: David Airlie <airlied@linux.ie> Cc: Archit Taneja <architt@codeaurora.org> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Wolfram Sang <wsa+renesas@sang-engineering.com> Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Cc: "Ville Syrjälä" <ville.syrjala@linux.intel.com> Cc: Boris Brezillon <boris.brezillon@free-electrons.com> Cc: Andy Green <andy@warmcat.com> Cc: Dave Long <dave.long@linaro.org> Cc: Guodong Xu <guodong.xu@linaro.org> Cc: Zhangfei Gao <zhangfei.gao@linaro.org> Cc: Mark Brown <broonie@kernel.org> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Jose Abreu <joabreu@synopsys.com> Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Cc: dri-devel@lists.freedesktop.org Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/1480382552-28219-3-git-send-email-john.stultz@linaro.org
2016-11-29drm/bridge: adv7511: Add Audio supportJohn Stultz
This patch adds support to Audio for both adv7511 and adv7533 bridge chips. This patch was originally from [1] by Lars-Peter Clausen <lars@metafoo.de> and was adapted by Archit Taneja <architt@codeaurora.org> and Srinivas Kandagatla <srinivas.kandagatla@linaro.org>. Then I heavily reworked it to use the hdmi-codec driver. And also folded in some audio packet initialization done by Andy Green <andy.green@linaro.org>. So credit to them, but blame to me. [1] https://github.com/analogdevicesinc/linux/blob/xcomm_zynq/drivers/gpu/drm/i2c/adv7511_audio.c Cc: David Airlie <airlied@linux.ie> Cc: Archit Taneja <architt@codeaurora.org> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Wolfram Sang <wsa+renesas@sang-engineering.com> Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Cc: "Ville Syrjälä" <ville.syrjala@linux.intel.com> Cc: Boris Brezillon <boris.brezillon@free-electrons.com> Cc: Andy Green <andy@warmcat.com> Cc: Dave Long <dave.long@linaro.org> Cc: Guodong Xu <guodong.xu@linaro.org> Cc: Zhangfei Gao <zhangfei.gao@linaro.org> Cc: Mark Brown <broonie@kernel.org> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Jose Abreu <joabreu@synopsys.com> Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Cc: dri-devel@lists.freedesktop.org Acked-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/1480382552-28219-2-git-send-email-john.stultz@linaro.org
2016-11-28drm: bridge: dw-hdmi: add ASoC dependencyArnd Bergmann
The newly added sound driver depends on SND_SOC_HDMI_CODEC, which in turn only makes sense when ASoC is enabled, as shown by this warning: warning: (DRM_MSM && DRM_STI && DRM_MEDIATEK_HDMI && DRM_I2C_NXP_TDA998X && DRM_DW_HDMI_I2S_AUDIO) selects SND_SOC_HDMI_CODEC which has unmet direct dependencies (SOUND && !M68K && !UML && SND && SND_SOC) Since the audio driver is probably useless without the audio subsystem, adding a dependency here seems the right solution. Fixes: 2761ba6c0925 ("drm: bridge: add DesignWare HDMI I2S audio support") Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/20161125205411.1157522-1-arnd@arndb.de
2016-11-24drm: bridge: add DesignWare HDMI I2S audio supportKuninori Morimoto
Current dw-hdmi is supporting sound via AHB bus, but it has I2S audio feature too. This patch adds I2S audio support to dw-hdmi. This HDMI I2S is supported by using ALSA SoC common HDMI encoder driver. Tested-by: Jose Abreu <joabreu@synopsys.com> Acked-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/8737j2bxba.wl%kuninori.morimoto.gx@renesas.com
2016-11-17drm/bridge: dumb-vga-dac: Support a VDD regulator supplyChen-Yu Tsai
Some dumb VGA DACs are active components which require external power. Add support for specifying a regulator as its power supply. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/20161116154232.872-2-wens@csie.org
2016-11-16drm/bridge: analogix_dp: return error if transfer none byteJianqun Xu
Reference from drm_dp_aux description (about transfer): Upon success, the implementation should return the number of payload bytes that were transferred, or a negative error-code on failure. Helpers propagate errors from the .transfer() function, with the exception of the -EBUSY error, which causes a transaction to be retried. On a short, helpers will return -EPROTO to make it simpler to check for failure. The analogix_dp_transfer will return num_transferred, but if there is none byte been transferred, the return value will be 0, which means success, we should return error-code if transfer none byte. for (retry = 0; retry < 32; retry++) { err = aux->transfer(aux, &msg); if (err < 0) { if (err == -EBUSY) continue; goto unlock; } } Cc: zain wang <wzz@rock-chips.com> Reviewed-by: Sean Paul <seanpaul@chromium.org> Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/1479255219-7243-1-git-send-email-jay.xu@rock-chips.com
2016-11-11Merge tag 'dw-hdmi-next-2016-09-19' of ↵Dave Airlie
git://git.pengutronix.de/git/pza/linux into drm-next dw-hdmi i2c master controller - add support for the HDMI I2C master controller, for boards that can have their DDC pins connected only to the HDMI TX directly. * tag 'dw-hdmi-next-2016-09-19' of git://git.pengutronix.de/git/pza/linux: drm: bridge/dw_hdmi: add dw hdmi i2c bus adapter support drm: dw_hdmi: use of_get_i2c_adapter_by_node interface
2016-10-27drm/bridge: fix platform_no_drv_owner.cocci warningskbuild test robot
drivers/gpu/drm/bridge/sil-sii8620.c:1556:3-8: No need to set .owner here. The core will do it. Remove .owner field if calls are used which set it automatically Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci CC: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/20161026165836.GA98766@lkp-sb04.lkp.intel.com
2016-10-27drm/bridge: fix semicolon.cocci warningskbuild test robot
drivers/gpu/drm/bridge/sil-sii8620.c:988:2-3: Unneeded semicolon Remove unneeded semicolon. Generated by: scripts/coccinelle/misc/semicolon.cocci CC: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/20161026165836.GA98907@lkp-sb04.lkp.intel.com
2016-10-26drm/bridge: add Silicon Image SiI8620 driverAndrzej Hajda
SiI8620 transmitter converts eTMDS/HDMI signal to MHL 3.0. It is controlled via I2C bus. Its interaction with other devices in video pipeline is performed mainly on HW level. The only interaction it does on device driver level is filtering-out unsupported video modes, it exposes drm_bridge interface to perform this operation. Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/1476085157-5266-1-git-send-email-a.hajda@samsung.com
2016-10-10drm/bridge: Drop drm_connector_unregister and call drm_connector_cleanup ↵Marek Vasut
directly Drop unneeded drm_connector_unregister() and remove the unnecessary wrapper functions around drm_connector_cleanup(). Signed-off-by: Marek Vasut <marex@denx.de> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/20161005143133.5549-1-marex@denx.de
2016-10-10drm/bridge: Add RGB to VGA bridge supportMaxime Ripard
Some boards have an entirely passive RGB to VGA bridge, based on DACs implemented by resistor ladders. Those might or might not have an i2c bus routed to the VGA connector in order to access the screen EDIDs. Add a bridge that doesn't do anything but expose the modes available on the screen, either based on the EDIDs if available, or based on the XGA standards. Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Sean Paul <seanpaul@chromium.org> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/20160930143709.1388-3-maxime.ripard@free-electrons.com
2016-10-05drm/bridge: Call drm_connector_cleanup directlyMarek Vasut
Remove the unnecessary wrapper functions around drm_connector_cleanup(). Signed-off-by: Marek Vasut <marex@denx.de> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/20161004222331.7200-1-marex@denx.de
2016-10-04drm/bridge: analogix_dp: Add analogix_dp_psr_supportedTomeu Vizoso
So users know whether PSR should be enabled or not. Cc: Yakir Yang <ykk@rock-chips.com> Reviewed-by: Sean Paul <seanpaul@chromium.org> Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/1474639600-30090-1-git-send-email-tomeu.vizoso@collabora.com
2016-09-28Merge tag 'topic/drm-misc-2016-09-25' of ↵Dave Airlie
git://anongit.freedesktop.org/drm-intel into drm-next - more core cleanup patches to prep drm_file to be used for kernel-internal contexts (David Herrmann) - more split-up+docs for drm_crtc.c - lots of small fixes and polish all over * tag 'topic/drm-misc-2016-09-25' of git://anongit.freedesktop.org/drm-intel: (37 commits) drm: bridge: analogix/dp: mark symbols static where possible drm/bochs: mark bochs_connector_get_modes() static drm/bridge: analogix_dp: Improve panel on time drm/bridge: analogix_dp: Don't read EDID if panel present drm/bridge: analogix_dp: Remove duplicated code Revert "drm/i2c: tda998x: don't register the connector" drm: Fix plane type uabi breakage dma-buf/sync_file: free fences array in num_fences is 1 drm/i2c: tda998x: don't register the connector drm: Don't swallow error codes in drm_dev_alloc() drm: Distinguish no name from ENOMEM in set_unique() drm: Remove dirty property from docs drm/doc: Document color space handling drm: Extract drm_color_mgmt.[hc] drm/doc: Polish plane composition property docs drm: Conslidate blending properties in drm_blend.[hc] drm/doc: Polish for drm_plane.[hc] drm: Extract drm_plane.[hc] drm/tilcdc: Add atomic and crtc headers to crtc.c drm: Fix typo in encoder docs ...
2016-09-25drm: bridge: analogix/dp: mark symbols static where possibleBaoyou Xie
We get 2 warnings when building kernel with W=1: drivers/gpu/drm/bridge/analogix/analogix_dp_core.c:1053:5: warning: no previous prototype for 'analogix_dp_get_modes' [-Wmissing-prototypes] drivers/gpu/drm/bridge/analogix/analogix_dp_core.c:1097:1: warning: no previous prototype for 'analogix_dp_detect' [-Wmissing-prototypes] In fact, both functions are only used in the file in which they are declared and don't need a declaration, but can be made static. So this patch marks both functions with 'static'. Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/1474788764-6069-1-git-send-email-baoyou.xie@linaro.org
2016-09-24drm/bridge: analogix_dp: Improve panel on timeSean Paul
In order to reduce the time required to turn on the panel, this patch makes 2 assumptions: 1- In detect(): if there's a panel, we're connected. 2- In get_modes(): if there's a panel, let the panel driver decide if it should prepare/unprepare in order to get the modes. The first is straightforward, and shouldn't need further explanation. The second should eliminate the prepare/unprepare delays from get_modes() in most cases, since panels generally hardcode their modes in the driver as opposed to reading EDID. If a panel does need to read EDID, it should be responsible for ensuring it's in a state in which it can. Signed-off-by: Sean Paul <seanpaul@chromium.org>
2016-09-24drm/bridge: analogix_dp: Don't read EDID if panel presentSean Paul
If there's a panel connected to the analogix_dp bridge, rely on the panel driver for modes, rather than reading EDID *and* calling get_modes() on the panel. This allows panels with a valid EDID to read it in the panel driver (e.g. simple_panel), and panels with invalid EDID to homebrew modes in their get_modes implementation. Signed-off-by: Sean Paul <seanpaul@chromium.org>
2016-09-24drm/bridge: analogix_dp: Remove duplicated codeTomeu Vizoso
Remove code for reading the EDID and DPCD fields and use the helpers instead. Besides the obvious code reduction, other helpers are being added to the core that could be used in this driver and will be good to be able to use them instead of duplicating them. Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com> Tested-by: Javier Martinez Canillas <javier@osg.samsung.com> Tested-by: Sean Paul <seanpaul@chromium.org> Reviewed-by: Sean Paul <seanpaul@chromium.org> Signed-off-by: Sean Paul <seanpaul@chromium.org> Cc: Javier Martinez Canillas <javier@osg.samsung.com> Cc: Mika Kahola <mika.kahola@intel.com> Cc: Yakir Yang <ykk@rock-chips.com> Cc: Daniel Vetter <daniel.vetter@intel.com> Cc: Archit Taneja <architt@codeaurora.org>
2016-09-20Merge tag 'imx-drm-next-2016-09-19' of ↵Dave Airlie
git://git.pengutronix.de/git/pza/linux into drm-next imx-drm active plane reconfiguration, cleanup, FSU/IC/IRT/VDIC support - add active plane reconfiguration support (v4), use the atomic_disable callback - stop calling disable_plane manually in the plane destroy path - let mode cleanup destroy mode objects on driver unbind - drop deprecated load/unload drm_driver ops - add exclusive fence to plane state, so the atomic helper can wait on them, remove the open-coded fence wait from imx-drm - add low level deinterlacer (VDIC) support - add support for channel linking via the frame synchronisation unit (FSU) - add queued image conversion support for memory-to-memory scaling, rotation, and color space conversion, using IC and IRT. * tag 'imx-drm-next-2016-09-19' of git://git.pengutronix.de/git/pza/linux: gpu: ipu-v3: Add queued image conversion support gpu: ipu-v3: Add ipu_rot_mode_is_irt() gpu: ipu-v3: fix a possible NULL dereference drm/imx: parallel-display: detach bridge or panel on unbind drm/imx: imx-ldb: detach bridge on unbind drm/imx: imx-ldb: detach panel on unbind gpu: ipu-v3: Add FSU channel linking support gpu: ipu-v3: Add Video Deinterlacer unit drm/imx: add exclusive fence to plane state drm/imx: fold ipu_plane_disable into ipu_disable_plane drm/imx: don't destroy mode objects manually on driver unbind drm/imx: drop deprecated load/unload drm_driver ops drm/imx: don't call disable_plane in plane destroy path drm/imx: Add active plane reconfiguration support drm/imx: Use DRM_PLANE_COMMIT_NO_DISABLE_AFTER_MODESET flag drm/imx: ipuv3-crtc: Use the callback ->atomic_disable instead of ->disable gpu: ipu-v3: Do not wait for DMFC FIFO to clear when disabling DMFC channel
2016-09-19drm: bridge/dw_hdmi: add dw hdmi i2c bus adapter supportVladimir Zapolskiy
The change adds support of internal HDMI I2C master controller, this subdevice is used by default, if "ddc-i2c-bus" DT property is omitted. The main purpose of this functionality is to support reading EDID from an HDMI monitor on boards, which don't have an I2C bus connected to DDC pins. The current implementation does not support "I2C Master Interface Extended Read Mode" to read data addressed by non-zero segment pointer, this means that if EDID has more than 1 extension blocks, EDID reading operation won't succeed, in my practice all tested HDMI monitors have at maximum one extension block. Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com> Acked-by: Rob Herring <robh@kernel.org> Tested-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
2016-09-19drm: dw_hdmi: use of_get_i2c_adapter_by_node interfaceVladimir Zapolskiy
This change is needed to properly lock I2C bus driver, which serves DDC. The change fixes an overflow over zero of I2C bus driver user counter: root@imx6q:~# lsmod Not tainted dw_hdmi_ahb_audio 4082 0 - Live 0xbf02c000 dw_hdmi_imx 3498 0 - Live 0xbf00d000 dw_hdmi 16398 2 dw_hdmi_ahb_audio,dw_hdmi_imx, Live 0xbf004000 i2c_imx 16687 0 - Live 0xbf017000 root@imx6q:~# rmmod dw_hdmi_imx root@imx6q:~# lsmod Not tainted dw_hdmi_ahb_audio 4082 0 - Live 0xbf02c000 dw_hdmi 16398 1 dw_hdmi_ahb_audio, Live 0xbf004000 i2c_imx 16687 -1 - Live 0xbf017000 ^^ root@imx6q:~# rmmod i2c_imx rmmod: ERROR: Module i2c_imx is in use Note that prior to this change put_device() coupled with of_find_i2c_adapter_by_node() was missing on error path of dw_hdmi_bind(), added i2c_put_adapter() there along with the change. Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com> Acked-by: Russell King <rmk+kernel@arm.linux.org.uk> Cc: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
generated by cgit (git 2.34.1) at 2025-09-19 09:12:13 +0000