| Age | Commit message (Collapse) | Author |
|---|
|
Unlike previous platforms that used PORT_TX_DFLEXDPSP
for max_lane calculation, MTL uses only PORT_TX_DFLEXPA1
from which the max_lanes has to be calculated.
Bspec: 50235, 65380
Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Jose Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428095433.4109054-13-mika.kahola@intel.com
|
|
The HPD live status for MTL has to be read from different set of
registers. MTL deserves a new function for this purpose
and cannot reuse the existing HPD live status detection
Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428095433.4109054-12-mika.kahola@intel.com
|
|
Add register writes to enable powering up Type-C subsystem i.e. TCSS.
For MeteorLake we need to request TCSS to power up and check the TCSS
power state after 500 us.
In addition, for PICA we need to set/clear the Type-C PHY ownnership
bit when Type-C device is connected/disconnected.
Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428095433.4109054-11-mika.kahola@intel.com
|
|
There's not much point in a static work function having a kernel-doc
comment. Just clean it up and make it a regular comment.
This fixes the kernel-doc warnings:
drivers/gpu/drm/i915/display/intel_tc.c:1370: warning: Function
parameter or member 'work' not described in
'intel_tc_port_disconnect_phy_work'
drivers/gpu/drm/i915/display/intel_tc.c:1370: warning: Excess function
parameter 'dig_port' description in 'intel_tc_port_disconnect_phy_work'
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230405104142.766598-1-jani.nikula@intel.com
|
|
After the previous patch the workaround for a TC PHY hang issue is not
required any more, remove it.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-29-imre.deak@intel.com
|
|
Bspec has updated the TC connect/disconnect sequences, add the required
platform hooks for these.
The difference wrt. the old sequence is the order of taking the PHY
ownership - while holding a port power reference this requires - and
blocking the TC-cold power state.
Bspec: 49294
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-26-imre.deak@intel.com
|
|
Connecting the PHY for connector probing - also blocking TC-cold - isn't
required and has some overhead. Taking only the mutex is sufficient, so
do that.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-25-imre.deak@intel.com
|
|
Enable the power required for the HPD live status register access
instead of depending on the caller blocking the TC-cold power state
(during HW readout and connector probing).
A follow up patch will remove connecting/disconnecting the PHY around
connector probing, so querying the HPD status can happen in this case
without TC-cold being blocked.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-24-imre.deak@intel.com
|
|
The spec says to use the CPU ISR registers for DP-alt/TBT HPD detection
on ADLP, so do that instead of using the related IOM/TCSS registers.
Bspec: 55480, 55482, 49212, 49305
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-23-imre.deak@intel.com
|
|
Add a hook for platform specific PHY initialization. Move the detection
of modular FIAs to the TGL handler, skipping this on ADLP+ where the
FIAs are always modular, not requiring a detection.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-22-imre.deak@intel.com
|
|
Add an assert to each TC PHY hook that their required power domain is
enabled.
While at it add a comment describing the domains used on each platform
and TC mode.
v2: Fix non kernel-doc multiline comments. (Jani)
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-21-imre.deak@intel.com
|
|
Instead of the corresponding if ladder, add a TC PHY hook to get the
platform and TC mode specific power domain used for blocking the TC-cold
power state.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-20-imre.deak@intel.com
|
|
Simplify tc_cold_block()/unblock() by dropping their power domain
parameter. The power domain depends on the current TC mode, which -
after the previous patch - can't change while the PHY is connected,
holding a TC-cold-off power domain reference. Based on this the domain
can be deducted from the current TC mode instead of having to pass this
as a parameter.
Blocking TC-cold for the PHY HW readout happens before the current TC
mode is determined, so here the initial power domain must be still
manually passed.
For debugging still keep track of the domain used for tc_cold_block()
and verify that it remained the same until tc_cold_unblock().
While at it rename tc_cold_get_power_domain() to
tc_phy_cold_off_domain(), reflecting the name of platform specific hook
added in the next patch.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-19-imre.deak@intel.com
|
|
After the previous patch unblock_tc_cold() will not be called in a
disconnected mode, so the wakeref passed to it will be always non-zero.
Remove the redundant check.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-18-imre.deak@intel.com
|
|
Move blocking/unblocking the TC-cold power state to the platform
specific PHY connect / disconnect hooks. This allows for adjusting the
connect/disconnect sequence as required for each platform.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-17-imre.deak@intel.com
|
|
After the previous patch the TC mode in the connect/disconnect functions
is always in sync with the VBT legacy port flag, so for consistency with
the rest of the function check the TC mode instead of the VBT flag.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-16-imre.deak@intel.com
|
|
A follow-up patch simplifies the tc_cold_block()/unblock() functions,
dropping the power domain parameter. For this it must be ensured that
the power domain - which depends on the actual TC mode and so the VBT
legacy port flag - can't change while the PHY is in a connected state
and accordingly TC-cold is blocked. Make this so, by fixing up the VBT
legacy flag only in the disconnected TC mode, instead of whenever the
HPD state is retrieved.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-15-imre.deak@intel.com
|
|
Add TC PHY hooks to connect/disconnect the PHY. A follow-up patch will
add the ADLP specific hooks for these.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-14-imre.deak@intel.com
|
|
Factor out a function verifying the PHY connected state in legacy or
DP-alt mode. This is common to all platforms, which can be reused in
platform specific connect hooks added in follow-up patches.
No functional changes.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-13-imre.deak@intel.com
|
|
Add generic handlers to connect/disconnect a PHY.
Setting the TC mode to the target mode deducted from the HPD state and -
if connecting to this mode fails - falling back to connecting to the
default (TBT) mode are common to all platforms; move the logic for this
from the ICL specific connect / disconnect handlers to the generic ones.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-12-imre.deak@intel.com
|
|
Add a TC PHY hook to read out the PHY HW state on each platform, move
the common parts to the generic helper.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-11-imre.deak@intel.com
|
|
Add TC PHY hooks to get the PHY ready/owned state on each platform,
replacing the corresponding if ladder.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-10-imre.deak@intel.com
|
|
Add a table of TC PHY hooks which can be used to call platform specific
TC PHY handlers, replacing the corresponding if ladders.
Add the hook to retrieve the PHY's HPD live status. Move the common part
fixing up the VBT legacy port flag to the generic helper.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-9-imre.deak@intel.com
|
|
Move the intel_tc_port struct to intel_tc.c for better isolation. This
requires allocating the struct dynamically.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-8-imre.deak@intel.com
|
|
Check explicitly if the port passed to
intel_tc_port_fia_max_lane_count() has a TC PHY, instead of relying on
the default TC mode value set for non-TC PHY ports.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-7-imre.deak@intel.com
|
|
Move the TC port specific fields from intel_digital_port to a new
intel_tc_port struct. Pass an intel_tc_port pointer to all static
functions in intel_tc.c keeping dig_port accessible for these via a
pointer stored in the new struct.
The next patch will allocate the intel_tc_port dynamically, allowing
moving the struct definition to intel_tc.c.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-6-imre.deak@intel.com
|
|
For consistency use the tc_phy prefix for all TC PHY functions.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-5-imre.deak@intel.com
|
|
For consistency rename tc_phy_status_complete() to tc_phy_is_ready()
following the terminology of new platforms.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-4-imre.deak@intel.com
|
|
Use the usual adlp prefix for all ADLP specific TC PHY functions. Other
ADL platforms don't support TC.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-3-imre.deak@intel.com
|
|
Arrange the TC PHY HW state setup/query functions into platform
specific and generic groups. This prepares for upcoming patches adding
generic TC PHY handlers and platform specific hooks for these,
replacing the corresponding if ladders.
No functional changes.
v2: Fix non kernel-doc multiline comments. (Jani)
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-2-imre.deak@intel.com
|
|
The current way to determine during HW state sanitization if a PHY is
connected in the expected way doesn't work in all cases. The check for
this considers only the PHY ready/owned state and the initial TC mode
which was determined earlier by the TC port HW readout - using the
sink's HPD and the same PHY ready/owned states.
For instance for an enabled DP-alt/TBT port without the PHY ready/owned
flags set the initial mode will be TBT, and this will be regarded as a
valid PHY state. However it's possible that the port is actually enabled
in DP-alt mode, but for some reason the PHY ownership was not acquired.
Make sure the driver can detect invalid PHY states as in the above
example by checking the PHY ready/owned state wrt. the PLL type used.
This should be the TBT PLL if the PHY is not owned and the MG (non-TBT)
PLL if the PHY is owned.
v2: Rebased on change passing crtc_state in the previous patch.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230321220101.983366-3-imre.deak@intel.com
|
|
For clarity factor out the function to determine if there are active
links on a TC port. This prepares for the next patch also checking the
port's PLL type.
While at it pass crtc_state to intel_tc_port_sanitize_mode(), and check
hw.active in that, instead of the deprecated crtc->active flag.
v2: Check crtc_state->hw.active instead of crtc->active. (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230321220101.983366-2-imre.deak@intel.com
|
|
For consistency detect the initial TC mode in the PHY owned state the
same way this is done in the not owned state (w/o changing the
behavior). While at it, add more details to the PHY state debug print.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-11-imre.deak@intel.com
|
|
Atm, a TC port's initial mode will be read out as TBT mode in any case
the PHY ownership is not held. This isn't correct for legacy ports which
should be used only in legacy mode.
Fix the above initial mode to be disconnected mode for a legacy port and
TBT mode for DP-alt/TBT ports. Determine the port type by checking first
the HPD state and then the legacy VBT flag (so the HPD state can correct
a bogus VBT flag). If a sink is connected on a disabled port the PHY
will get also connected (switching it to legacy mode on a legacy port).
Also connect the PHY on a legacy port if it's enabled but BIOS
incorrectly left it in the disconnected state for some reason.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-10-imre.deak@intel.com
|
|
A legacy TC port can't be switched to TBT mode, even if the PHY
initialization wasn't ready yet for some reason, so prevent this.
This shouldn't normally happen as the driver waits for the IOM/TCSS
PHY initialization during driver loading and system resume.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-9-imre.deak@intel.com
|
|
Atm, the target TC mode - which the PHY should be switched to at any
point it's used - is TBT in case there is no sink connected. However
legacy ports are only used in the legacy mode regardless of the sink
connected state. Fix the mode returned by
intel_tc_port_get_target_mode() accordingly.
Despite of the above issue, the PHY got disconnected as expected in
response to a sink disconnect event, causing only a redundant
PHY disconnect->reconnect sequence whenever the port was used.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-8-imre.deak@intel.com
|
|
Factor out helpers used later in the patchset to convert an HPD
status mask to TC mode or target TC mode.
No functional changes.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-7-imre.deak@intel.com
|
|
During boot-up/system resume, the TC PHY on legacy ports will be
initialized by the IOM/TCSS firmware regardless of a sink being
connected or not (as opposed to DP-alt/TBT ports, which the FW only
inits once a sink is connected).
Wait for the above initialization to complete during HW readout, so that
connecting the PHY later will already see the expected PHY ready state.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-6-imre.deak@intel.com
|
|
At least restoring the MST topology during system resume needs to use
AUX before the display HW readout->sanitization sequence is complete,
but on TC ports the PHY may be in the wrong mode for this, resulting in
the AUX transfers to fail.
The initial TC port mode is kept fixed as BIOS left it for the above HW
readout sequence (to prevent changing the mode on an enabled port). If
the port is disabled this initial mode is TBT - as in any case the PHY
ownership is not held - even if a DP-alt sink is connected. Thus, the
AUX transfers during this time will use TBT mode instead of the expected
DP-alt mode and so time out.
Fix the above by connecting the PHY during port initialization if the
port is disabled, which will switch to the expected mode (DP-alt in the
above case).
As the encoder/pipe HW state isn't read-out yet at this point, check if
the port is enabled based on the DDI_BUF enabled flag. Save the read-out
initial mode, so intel_tc_port_sanitize_mode() can check this wrt. the
read-out encoder HW state.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-5-imre.deak@intel.com
|
|
The commit renaming icl_tc_phy_is_in_safe_mode() to
icl_tc_phy_take_ownership() didn't flip the function's return value
accordingly, fix this up.
This didn't cause an actual problem besides state check errors, since
the function is only used during HW readout.
Cc: José Roberto de Souza <jose.souza@intel.com>
Fixes: f53979d68a77 ("drm/i915/display/tc: Rename safe_mode functions ownership")
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-4-imre.deak@intel.com
|
|
An enabled TC MST port holds one TC port link reference, regardless of
the number of enabled streams on it, but the TC port HW readout takes
one reference for each active MST stream.
Fix the HW readout, taking only one reference for MST ports.
This didn't cause an actual problem, since the encoder HW readout doesn't
yet support reading out the MST HW state.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-3-imre.deak@intel.com
|
|
On TC ports the 4ms AUX timeout combined with the 5 * 32 retry
attempts during DPCD accesses adds a 640ms delay to each access if the
sink is disconnected. This in turn slows down a modeset during which the
sink is disconnected (for instance a disabling modeset).
Prevent the above delay by aborting AUX transfers on a TC port with a
disconnected sink.
The DP 1.4a link CTS (4.2.1.5 Source Device Inactive HPD / Inactive AUX
Test") also requires not to initiate AUX transfers on disconnected DP
ports in general, however this patch doesn't change the behavior on
non-TC ports, leaving that for a follow-up.
Reported-and-tested-by: Chris Chiu <chris.chiu@canonical.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8279
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-2-imre.deak@intel.com
|
|
Avoid direct uncore use in display code.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/8c29f4f76c2163da309ead0bf48652024f134f11.1670433372.git.jani.nikula@intel.com
|
|
Move the TypeC DKL PHY register definitions to intel_dkl_phy_regs.h.
No functional changes.
v2:
- Move the definitions to a new intel_dkl_phy_regs.h file. (Jani).
v3:
- Rebase on latest patchset version.
Cc: Jani Nikula <jani.nikula@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221025114457.2191004-2-imre.deak@intel.com
|
|
An upcoming patch moves the DKL PHY register definitions to
intel_dkl_phy_regs.h, so for consistency rename intel_tc_phy_regs.h
containing only MG PHY register definitions to intel_mg_phy_regs.h.
Suggested-by: Jani Nikula <jani.nikula@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221025102644.2123988-3-imre.deak@intel.com
|
|
There is special helper for register read/modify/write.
Signed-off-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221006163200.2803722-5-andrzej.hajda@intel.com
|
|
During system resume DP MST requires AUX to be working already before
the HW state readout of the given encoder. Since AUX requires the
encoder/PHY TypeC mode to be initialized, which atm only happens during
HW state readout, these AUX transfers can change the TypeC mode
incorrectly (disconnecting the PHY for an enabled encoder) and trigger
the state check WARNs in intel_tc_port_sanitize().
Fix this by initializing the TypeC mode earlier both during driver
loading and system resume and making sure that the mode can't change
until the encoder's state is read out. While at it add the missing
DocBook comments and rename
intel_tc_port_sanitize()->intel_tc_port_sanitize_mode() for consistency.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220922172148.2913088-1-imre.deak@intel.com
|
|
Move display hotplug related members under drm_i915_private display
sub-struct.
Rename struct i915_hotplug to intel_hotplug while at it.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/c1c7562a31c115e9d6a131861e4ca9c97d4f7e09.1661346845.git.jani.nikula@intel.com
|
|
Commit 30e114ef4b16 ("drm/i915/tc: Check for DP-alt, legacy sinks before
taking PHY ownership") defaults any disconnected Type-C ports to TBT-alt
mode which presents a problem (which could most likely result in a system
hang) when userspace forces a modeset on a Type-C port that is wired for
legacy HDMI. The following warning is seen when Weston forces a modeset
on a disconnected legacy Type-C port (HDMI) on a TGL based Gigabyte system:
(https://www.gigabyte.com/Mini-PcBarebone/GB-BSi3-1115G4-rev-10#ov)
Missing case (clock == 173000)
WARNING: CPU: 1 PID: 438 at drivers/gpu/drm/i915/display/intel_ddi.c:245
icl_ddi_tc_enable_clock.cold+0x16a/0x1cf [i915]
CPU: 1 PID: 438 Comm: kworker/u8:3 Tainted: G U W E
5.18.0-rc5-drm-tip+ #20
Hardware name: GIGABYTE GB-BSi3-1115G4/GB-BSi3-1115G4, BIOS F9
10/16/2021
Workqueue: i915_modeset intel_atomic_commit_work [i915]
RIP: 0010:icl_ddi_tc_enable_clock.cold+0x16a/0x1cf [i915]
Code: 74 6c 7f 10 81 fd d0 78 02 00 74 6d 81 fd b0 1e 04 00 74 70 48 63
d5 48 c7 c6 c0 7b ab c0 48 c7 c7 20 75 ab c0 e8 b8 b5 c1 f0 <0f> 0b 45
31 ed e9 fb fe ff ff 49 63 d5
48 c7 c6 80 7b ab c0 48 c7
RSP: 0018:ffff8882522c78f0 EFLAGS: 00010282
RAX: 0000000000000000 RBX: 0000000000000003 RCX: 0000000000000000
RDX: 0000000000000027 RSI: 0000000000000004 RDI: ffffed104a458f10
RBP: 0000000000011558 R08: ffffffffb078de4e R09: ffff888269ca748b
R10: ffffed104d394e91 R11: 0000000000000000 R12: ffff888255a318f8
R13: 0000000000000002 R14: ffff888255a30000 R15: ffff88823ef00348
FS: 0000000000000000(0000) GS:ffff888269c80000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fd7afa42000 CR3: 0000000255c02004 CR4: 00000000007706e0
PKRU: 55555554
Call Trace:
<TASK>
intel_ddi_pre_enable.cold+0x96/0x5bf [i915]
intel_encoders_pre_enable+0x10e/0x140 [i915]
hsw_crtc_enable+0x207/0x99d [i915]
? ilk_crtc_enable.cold+0x2a/0x2a [i915]
? prepare_to_wait_exclusive+0x120/0x120
intel_enable_crtc+0x9a/0xf0 [i915]
skl_commit_modeset_enables+0x466/0x820 [i915]
? intel_commit_modeset_enables+0xd0/0xd0 [i915]
? intel_mbus_dbox_update+0x1ed/0x250 [i915]
intel_atomic_commit_tail+0xf2d/0x3040 [i915]
_raw_spin_lock_irqsave+0x87/0xe0
_raw_read_unlock_irqrestore+0x40/0x40
__update_load_avg_cfs_rq+0x70/0x5c0
__i915_sw_fence_complete+0x85/0x3b0 [i915]
? intel_get_crtc_new_encoder+0x190/0x190 [i915]
? sysvec_irq_work+0x13/0x90
? asm_sysvec_irq_work+0x12/0x20
? _raw_spin_lock_irq+0x82/0xd0
? read_word_at_a_time+0xe/0x20
? process_one_work+0x393/0x690
process_one_work+0x393/0x690
worker_thread+0x2b7/0x620
? process_one_work+0x690/0x690
kthread+0x15a/0x190
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x1f/0x30
Continuing with the modeset without setting the DDI clock results in
more warnings and eventually a system hang. This does not seem to
happen with disconnected legacy or DP-alt DP ports because the clock
rate defaults to 162000 (which is a valid TBT clock) during the link
training process. Therefore, to fix this issue, this patch avoids
setting disconnected Type-C legacy ports to TBT-alt mode which prevents
the selection of TBT PLL when a modeset is forced.
v2: (Imre)
- Retain the check for legacy hotplug live status to account for
incorrect VBTs.
Cc: Imre Deak <imre.deak@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220526001939.4031112-2-vivek.kasireddy@intel.com
|
|
Atm the port -> DDI and AUX power domain mapping is specified by relying
on the aliasing of the platform specific intel_display_power_domain enum
values. For instance D12+ platforms refer to the 'D' port and power
domain instances, which doesn't match the bspec terminology, on these
platforms the corresponding port is TC1. To make it clear what
port/domain the code refers to add a mapping between them which matches
the bspec terms on different display versions.
This also allows for removing the aliasing in enum values in a follow-up
patch.
v2: Add the functions to intel_display_power.c, use
intel_display_power_ prefix.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220414210657.1785773-14-imre.deak@intel.com
|
