| Age | Commit message (Collapse) | Author |
|---|
|
struct drm_dp_mst_topology_mgr currently stores a pointer to struct dev.
Changing this to instead hold a pointer to drm_device is more useful as it
gives access to DRM structures. This also makes it consistent with other
DRM structures like drm_crtc, drm_connector etc.
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1485301777-3465-2-git-send-email-dhinakaran.pandiyan@intel.com
|
|
Not validating the mode rate against max. link rate results in not pruning
invalid modes. For e.g, a HBR2 5.4 Gbps 2-lane configuration does not
support 4k@60Hz. But, we do not reject this mode.
So, make use of the helpers in intel_dp to validate mode data rate against
max. link data rate of a configuration.
v3: Renamed local variables again for consistency (Manasi)
v2: Renamed mode data rate local variable to be more explanatory.
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479243546-17189-1-git-send-email-dhinakaran.pandiyan@intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
|
|
This patch adds support for DP MST audio in i915.
Enable audio codec when DP MST is enabled if has_audio flag is set.
Disable audio codec when DP MST is disabled if has_audio flag is set.
Another separated patches to support DP MST audio will be implemented
in audio driver.
This patch is ported from
commit 3708d5e082c3 ("drm/i915: start adding dp mst audio")
And because commit 3708d5e082c3 ("drm/i915: start adding dp mst audio")
breaks MST multi-monitor setups on some platforms, the orignal patch is
reverted by
commit be754b101f70 ("Revert "drm/i915: start adding dp mst audio"")
As the multi-monitor setups issue is fixed, let's port the patch and
enable the dp mst audio.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Cc: Lyude <cpaul@redhat.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1480334827-112273-3-git-send-email-libin.yang@intel.com
|
|
dp_encoder_is_mst flag in the crtc state can be replaced by
intel_crtc_has_type(..., INTEL_OUTPUT_DP_MST). Let's do that.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jim Bride <jim.bride@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479145447-12907-2-git-send-email-ville.syrjala@linux.intel.com
|
|
This reverts 'commit 3708d5e082c3 ("drm/i915: start adding dp mst audio")'
because it breaks MST multi-monitor setups on some platforms.
Fixes: 3708d5e082c3 ("drm/i915: start adding dp mst audio")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97907
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reported-by: Kim Lidström <kim@dxtr.im>
Cc: Libin Yang <libin.yang@linux.intel.com>
Cc: Lyude <cpaul@redhat.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1475132104-2754-1-git-send-email-dhinakaran.pandiyan@intel.com
|
|
(This patch is developed by Dave Airlie <airlied@redhat.com> originally)
This patch adds support for DP MST audio in i915.
Enable audio codec when DP MST is enabled if has_audio flag is set.
Disable audio codec when DP MST is disabled if has_audio flag is set.
Another separated patches to support DP MST audio will be implemented
in audio driver.
v2:
Rebased.
Signed-off-by: Libin Yang <libin.yang@linux.intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Lyude <cpaul@redhat.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1474334681-22690-6-git-send-email-dhinakaran.pandiyan@intel.com
|
|
Storing the port enum in intel_encoder makes it convenient to know the
port attached to an encoder. Moving the port information up from
intel_digital_port to intel_encoder avoids unecessary intel_digital_port
access and handles MST encoders cleanly without requiring conditional
checks for them (thanks danvet).
v2:
Renamed the port enum member from 'attached_port' to 'port' (danvet)
Fixed missing initialization of port in intel_sdvo.c (danvet)
v3:
Fixed missing initialization of port in intel_crt.c (Ville)
v4:
Storing port for DVO encoders too.
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Lyude <cpaul@redhat.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1474334681-22690-3-git-send-email-dhinakaran.pandiyan@intel.com
|
|
The value of ddi_pll_sel is derived from the selection of shared dpll,
so just calculate the final value when necessary.
v2: Actually remove it from crtc state and delete remaining usages. (CI)
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Decouple intel_dp_set_link_params() from struct intel_crtc_state. This
will be useful for implementing DP upfront link training.
v2:
* Rebased on atomic state changes (Manasi)
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470755054-32699-14-git-send-email-maarten.lankhorst@linux.intel.com
[mlankhorst: Address bikeshed.]
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Now that conn_state is passed in as argument to compute_config, it's
guaranteed that there is a connector for the argument. The code that
looks for the connector is now dead, and completely unused. Delete it.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470755054-32699-8-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Some places iterate over connector_state to find the right
connector, pass it along as argument.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470755054-32699-7-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This is mostly code churn, with exception of a few places:
- intel_display.c has changes in intel_sanitize_encoder
- intel_ddi.c has intel_ddi_fdi_disable calling intel_ddi_post_disable,
and required a function change. Also affects intel_display.c
- intel_dp_mst.c passes a NULL crtc_state and conn_state to
intel_ddi_post_disable for shutting down the real encoder.
If we would pass conn_state, then conn_state->connector !=
intel_dig_port->connector and conn_state->best_encoder !=
to_intel_encoder(intel_dig_port).
We also shouldn't pass crtc_state, because in that case the
disabling sequence may potentially be different depending on
which crtc is disabled last. Nice way to introduce bugs.
No other functional changes are done, diff stat is already huge.
Each encoder type will need to be fixed to use the atomic states
separately.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470755054-32699-6-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This reverts commit f64425a82bdb5c3d7e09ba765716da88a9b00eec.
active_streams will get totally out of whack with SST unless we
sync up with the hw state at readout, obviously! We don't yet
do that, so now the WARNs fire all the time. Let's revert :(
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470413142-26402-1-git-send-email-ville.syrjala@linux.intel.com
References: https://bugs.freedesktop.org/show_bug.cgi?id=95472#c14
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
s/active_mst_links/active_streams/ and use it also for SST. We can then
use this information in the hpd handling to see if the link is active
or not, and thus whether we may need to retrain.
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Cc: Jim Bride <jim.bride@linux.intel.com>
Cc: Manasi D Navare <manasi.d.navare@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1469717448-4297-6-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
DDI buffer prorgramming works quite differently depending on
the mode of the DDI port (DP/eDP/FDI vs. HDMI/DVI). Let's split
the function that does the programming into two matching variants
as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1468328376-6380-7-git-send-email-ville.syrjala@linux.intel.com
|
|
Use the new output_types bitmask instead of has_dp_encoder.
To make it less oainlful provide a small helper
(intel_crtc_has_dp_encoder()) to do the bitsy stuff.
v2: Rebase
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466621833-5054-7-git-send-email-ville.syrjala@linux.intel.com
|
|
Since we now subclass struct drm_device, we can save pointer dances by
noting the equivalence of struct drm_device and struct drm_i915_private,
i.e. by using to_i915().
text data bss dec hex filename
1073824 4562 416 1078802 107612 drivers/gpu/drm/i915/i915.ko
1068976 4562 416 1073954 106322 drivers/gpu/drm/i915/i915.ko
Created by the coccinelle script:
@@
expression E;
identifier p;
@@
- struct drm_i915_private *p = E->dev_private;
+ struct drm_i915_private *p = to_i915(E);
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467628477-25379-1-git-send-email-chris@chris-wilson.co.uk
|
|
By using the out-of-line intel_wait_for_register() not only do we can
efficiency from using the hybrid wait_for() contained within, but we
avoid code bloat from the numerous inlined loops, in total (all patches):
text data bss dec hex filename
1078551 4557 416 1083524 108884 drivers/gpu/drm/i915/i915.ko
1070775 4557 416 1075748 106a24 drivers/gpu/drm/i915/i915.ko
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467297225-21379-28-git-send-email-chris@chris-wilson.co.uk
|
|
Currently the backlight is being registered in the load phase (before
the display and its objects are registered). Move the backlight
registration into the analogous phase by performing it from the
connector registration, just after its creation.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466773227-7994-3-git-send-email-chris@chris-wilson.co.uk
|
|
With the introduction of a connector->func for callback from
drm_connector_register() we can move all the tasks that we want to do
upon registration into that callback. Later, this will allow us to
reorder the registration and defer it until after the device is setup
and ready for userspace.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466773227-7994-2-git-send-email-chris@chris-wilson.co.uk
|
|
We now have a connector->func that serves the same purpose as our own
intel_connector->unregister vfunc allowing us to unwrap ourselves and
use drm_connector_register() (and friends) as the central function.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466160034-12173-2-git-send-email-chris@chris-wilson.co.uk
|
|
Rather than let the core generate usless encoder names, let's pass in
something that actually identifies the piece of hardware we're dealing
with.
v2: Use 'DSI %c' instead of 'MIPI %c' for DSI encoders (Jani)
v3: Use port_name() in DSI code since we have it
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464371966-15190-7-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
Backmerge request by Jani to get at
commit 249c4f538b1aae55d41699f8bafc6cb762a7f48f
Author: Deepak M <m.deepak@intel.com>
Date: Wed Mar 30 17:03:39 2016 +0300
drm: Add new DCS commands in the enum list
Some simple conflicts in intel_dp.c.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
Don't just free the connector when we get the destroy callback.
Drop a reference to it, and set it's mst_port to NULL so
no more mst work is done on it.
v2: core mst accepts NULLs fine. Cleanup EDID code properly.
v3: drop the extra reference we were taking.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Right now MST audio is causing too many kernel panics to really keep
around in the kernel. On top of that, even after fixing said panics it's
still basically non-functional (at least on all the setups I've tested
it on). Revert until we have a proper solution for this.
This reverts commit 3d52ccf52f2c51f613e42e65be0f06e4e6788093.
Signed-off-by: Lyude <cpaul@redhat.com>
Fixes: 3d52ccf52f2c ("drm/i915: start adding dp mst audio")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1462287692-28570-1-git-send-email-cpaul@redhat.com
|
|
After unplugging a DP MST display from the system, we have to go through
and destroy all of the DRM connectors associated with it since none of
them are valid anymore. Unfortunately, intel_dp_destroy_mst_connector()
doesn't do a good enough job of ensuring that throughout the destruction
process that no modesettings can be done with the connectors. As it is
right now, intel_dp_destroy_mst_connector() works like this:
* Take all modeset locks
* Clear the configuration of the crtc on the connector, if there is one
* Drop all modeset locks, this is required because of circular
dependency issues that arise with trying to remove the connector from
sysfs with modeset locks held
* Unregister the connector
* Take all modeset locks, again
* Do the rest of the required cleaning for destroying the connector
* Finally drop all modeset locks for good
This only works sometimes. During the destruction process, it's very
possible that a userspace application will attempt to do a modesetting
using the connector. When we drop the modeset locks, an ioctl handler
such as drm_mode_setcrtc has the oppurtunity to take all of the modeset
locks from us. When this happens, one thing leads to another and
eventually we end up committing a mode with the non-existent connector:
[drm:intel_dp_link_training_clock_recovery [i915]] *ERROR* failed to enable link training
[drm:intel_dp_aux_ch] dp_aux_ch timeout status 0x7cf0001f
[drm:intel_dp_start_link_train [i915]] *ERROR* failed to start channel equalization
[drm:intel_dp_aux_ch] dp_aux_ch timeout status 0x7cf0001f
[drm:intel_mst_pre_enable_dp [i915]] *ERROR* failed to allocate vcpi
And in some cases, such as with the T460s using an MST dock, this
results in breaking modesetting and/or panicking the system.
To work around this, we now unregister the connector at the very
beginning of intel_dp_destroy_mst_connector(), grab all the modesetting
locks, and then hold them until we finish the rest of the function.
CC: stable@vger.kernel.org
Signed-off-by: Lyude <cpaul@redhat.com>
Signed-off-by: Rob Clark <rclark@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1458155884-13877-1-git-send-email-cpaul@redhat.com
|
|
Manage the LCPLLs used with DisplayPort, so that all the HSW/BDW DPLLs
are managed by the shared dpll code.
v2: Introduce INTEL_DPLL_ALWAYS_ON flag to please state checker. (Ander)
v3: Initialize pll->flags in intel_shared_dpll_init(). (Ander)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457451987-17466-13-git-send-email-ander.conselvan.de.oliveira@intel.com
|
|
It is possible the we request to have a mode that has
higher pixel clock than our HW can support. This patch
checks if requested pixel clock is lower than the one
supported by the HW. The requested mode is discarded
if we cannot support the requested pixel clock.
This patch applies to DisplayPort MST.
V2:
- removed computation for max pixel clock
V3:
- cleanup by removing unnecessary lines
V4:
- max_pixclk variable renamed as max_dotclk
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1454419003-6001-4-git-send-email-mika.kahola@intel.com
|
|
Pull in Dave's drm-next pull request to have a clean base for 4.6.
Also, we need the various atomic state extensions Maarten recently
created.
Conflicts are just adjacent changes that all resolve to nothing in git
diff.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
git://anongit.freedesktop.org/drm-intel into drm-next
Since your main drm-next pull isn't out of the door yet I figured I might
as well flush out drm-misc instead of delaying for 4.6. It's really just
random stuff all over, biggest thing probably connector_mask tracking from
Maarten.
* tag 'topic/drm-misc-2016-01-17' of git://anongit.freedesktop.org/drm-intel: (24 commits)
drm/fb_cma_helper: Remove implicit call to disable_unused_functions
drm/sysfs: use kobj_to_dev()
drm/i915: Init power domains early in driver load
drm: Do not set connector->encoder in drivers
apple-gmux: Add initial documentation
drm: move MODULE_PARM_DESC to other file
drm/edid: index CEA/HDMI mode tables using the VIC
drm/atomic: Remove drm_atomic_connectors_for_crtc.
drm/i915: Update connector_mask during readout, v2.
drm: Remove opencoded drm_gem_object_release_handle()
drm: Do not set outparam on error during GEM handle allocation
drm/docs: more leftovers from the big vtable documentation pile
drm/atomic-helper: Reject legacy flips on a disabled pipe
drm/atomic: add connector mask to drm_crtc_state.
drm/tegra: Use __drm_atomic_helper_reset_connector for subclassing connector state, v2.
drm/atomic: Add __drm_atomic_helper_connector_reset, v2.
drm/i915: Set connector_state->connector using the helper.
drm: Use a normal idr allocation for the obj->name
drm: Only bump object-reference count when adding first handle
drm: Balance error path for GEM handle allocation
...
|
|
Move the ddi buffer translation programming to occur from the encoder
.pre_enable() hook, for just the ddi port we are enabling. Previously
we used to reprogram the translations for all ddi ports during
init and during power well enabling.
v2: s/intel_prepare_ddi_buffers/intel_prepare_ddi_buffer/ (Daniel)
Resolve conflicts due to dev_priv->atomic_cdclk_freq
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
We're supposed to pass the primary DP encoder to intel_ddi_clk_select(),
not the fake MST encoder. Do so.
There's no real bug here though, since intel_ddi_clk_select() only
checks if the encoder type is EDP (which it isn't for either the
primary DP encoder or the fake MST encoder), and it gets the DDI port
via intel_ddi_get_encoder_port() (which knows how to do the
fake->primary->port dance itself).
Fixes: e404ba8 ("drm/i915: Setup DDI clk for MST on SKL")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449597590-6971-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The drm_dp_mst_topology_cbs structures are never modified, so declare them
as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
git://anongit.freedesktop.org/drm-intel into drm-next
- fix atomic watermark recomputation logic (Maarten)
- modeset sequence fixes for LPT (Ville)
- more kbl enabling&prep work (Rodrigo, Wayne)
- first bits for mst audio
- page dirty tracking fixes from Dave Gordon
- new get_eld hook from Takashi, also included in the sound tree
- fixup cursor handling when placed at address 0 (Ville)
- refactor VBT parsing code (Jani)
- rpm wakelock debug infrastructure ( Imre)
- fbdev is pinned again (Chris)
- tune the busywait logic to avoid wasting cpu cycles (Chris)
* tag 'drm-intel-next-2015-12-18' of git://anongit.freedesktop.org/drm-intel: (81 commits)
drm/i915: Update DRIVER_DATE to 20151218
drm/i915/skl: Default to noncoherent access up to F0
drm/i915: Only spin whilst waiting on the current request
drm/i915: Limit the busy wait on requests to 5us not 10ms!
drm/i915: Break busywaiting for requests on pending signals
drm/i915: don't enable autosuspend on platforms without RPM support
drm/i915/backlight: prefer dev_priv over dev pointer
drm/i915: Disable primary plane if we fail to reconstruct BIOS fb (v2)
drm/i915: Pin the ifbdev for the info->system_base GGTT mmapping
drm/i915: Set the map-and-fenceable flag for preallocated objects
drm/i915: mdelay(10) considered harmful
drm/i915: check that we are in an RPM atomic section in GGTT PTE updaters
drm/i915: add support for checking RPM atomic sections
drm/i915: check that we hold an RPM wakelock ref before we put it
drm/i915: add support for checking if we hold an RPM reference
drm/i915: use assert_rpm_wakelock_held instead of opencoding it
drm/i915: add assert_rpm_wakelock_held helper
drm/i915: remove HAS_RUNTIME_PM check from RPM get/put/assert helpers
drm/i915: get a permanent RPM reference on platforms w/o RPM support
drm/i915: refactor RPM disabling due to RC6 being disabled
...
|
|
Done with coccinelle for the most part. However, it thinks '...' is
part of the semantic patch, so I put an 'int DOTDOTDOT' placeholder
in its place and got rid of it with sed afterwards.
@@
identifier dev, encoder, funcs;
@@
int drm_encoder_init(struct drm_device *dev,
struct drm_encoder *encoder,
const struct drm_encoder_funcs *funcs,
int encoder_type
+ ,const char *name, int DOTDOTDOT
)
{ ... }
@@
identifier dev, encoder, funcs;
@@
int drm_encoder_init(struct drm_device *dev,
struct drm_encoder *encoder,
const struct drm_encoder_funcs *funcs,
int encoder_type
+ ,const char *name, int DOTDOTDOT
);
@@
expression E1, E2, E3, E4;
@@
drm_encoder_init(E1, E2, E3, E4
+ ,NULL
)
v2: Add ', or NULL...' to @name kernel doc (Jani)
Annotate the function with __printf() attribute (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449670818-2966-1-git-send-email-ville.syrjala@linux.intel.com
|
|
This patch adds support for DP MST audio in i915.
Enable audio codec when DP MST is enabled if has_audio flag is set.
Disable audio codec when DP MST is disabled if has_audio flag is set.
Another separated patches to support DP MST audio will be implemented
in audio driver.
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Libin Yang <libin.yang@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449036584-105393-2-git-send-email-libin.yang@linux.intel.com
|
|
Linux 4.4-rc2
Backmerge to get at
commit 1b0e3a049efe471c399674fd954500ce97438d30
Author: Imre Deak <imre.deak@intel.com>
Date: Thu Nov 5 23:04:11 2015 +0200
drm/i915/skl: disable display side power well support for now
so that we can proplery re-eanble skl power wells in -next.
Conflicts are just adjacent lines changed, except for intel_fbdev.c
where we need to interleave the changs. Nothing nefarious.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
intelfb_create() is called once on driver initialization. If it fails,
ifbdev->helper.fbdev, ifbdev->fb or ifbdev->fb->obj may be NULL.
Further up in the call stack, intel_fbdev_initial_config() calls
intel_fbdev_fini() to tear down the ifbdev on failure. This calls
intel_fbdev_destroy() which dereferences ifbdev->fb. Fix the ensuing
oops.
Also check in these functions if ifbdev is not NULL to avoid oops:
i915_gem_framebuffer_info() is called on access to debugfs file
"i915_gem_framebuffer" and dereferences ifbdev, ifbdev->helper.fb
and ifbdev->helper.fb->obj.
intel_connector_add_to_fbdev() / intel_connector_remove_from_fbdev()
are called when registering / unregistering an mst connector and
dereference ifbdev.
v3: Drop additional null pointer checks in intel_fbdev_set_suspend(),
intel_fbdev_output_poll_changed() and intel_fbdev_restore_mode()
since they already check if ifbdev is not NULL, which is sufficient
now that intel_fbdev_fini() is called on initialization failure.
(Requested by Daniel Vetter <daniel.vetter@ffwll.ch>)
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: http://patchwork.freedesktop.org/patch/msgid/d05f0edf121264a9d0adb8ca713fd8cc4ae068bf.1447938059.git.lukas@wunner.de
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Set up the DDI->PLL mapping on SKL also for MST links. Might help make
MST operational on SKL.
v2: Rebased due to KBL
Improve the patch subject, Jesse provided the new one
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1439826380-18403-1-git-send-email-ville.syrjala@linux.intel.com
References: https://bugs.freedesktop.org/show_bug.cgi?id=91791
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
git://anongit.freedesktop.org/drm-intel into drm-next
- dmc fixes from Animesh (not yet all) for deeper sleep states
- piles of prep patches from Ville to make mmio functions type-safe
- more fbc work from Paulo all over
- w/a shuffling from Arun Siluvery
- first part of atomic watermark updates from Matt and Ville (later parts had to
be dropped again unfortunately)
- lots of patches to prepare bxt dsi support ( Shashank Sharma)
- userptr fixes from Chris
- audio rate interface between i915/snd_hda plus kerneldoc (Libin Yang)
- shrinker improvements and fixes (Chris Wilson)
- lots and lots of small patches all over
* tag 'drm-intel-next-2015-10-10' of git://anongit.freedesktop.org/drm-intel: (134 commits)
drm/i915: Update DRIVER_DATE to 20151010
drm/i915: Partial revert of atomic watermark series
drm/i915: Early exit from semaphore_waits_for for execlist mode.
drm/i915: Remove wrong warning from i915_gem_context_clean
drm/i915: Determine the stolen memory base address on gen2
drm/i915: fix FBC buffer size checks
drm/i915: fix CFB size calculation
drm/i915: remove pre-atomic check from SKL update_primary_plane
drm/i915: don't allocate fbcon from stolen memory if it's too big
Revert "drm/i915: Call encoder hotplug for init and resume cases"
Revert "drm/i915: Add hot_plug hook for hdmi encoder"
drm/i915: use error path
drm/i915/irq: Fix misspelled word register in kernel-doc
drm/i915/irq: Fix kernel-doc warnings
drm/i915: Hook up ring workaround writes at context creation time on Gen6-7.
drm/i915: Don't warn if the workaround list is empty.
drm/i915: Resurrect golden context on gen6/7
drm/i915/chv: remove pre-production hardware workarounds
drm/i915/snb: remove pre-production hardware workaround
drm/i915/bxt: Set time interval unit to 0.833us
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux into drm-next
Backmerge the drm-fixes pull from Linus's tree into drm-next.
This is to fix some conflicts and make future pulls cleaner
|
|
The link training functions had confusing names. The start function
actually does the clock recovery phase of the link training, and the
complete function does the channel equalization. So call them that
instead. Also, every call to intel_dp_start_link_train() was followed
by a call to intel_dp_complete_link_train(), so add a new start
function that calls clock_recory and channel_equalization.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
git://anongit.freedesktop.org/drm-intel into drm-next
- initialize backlight from VBT as fallback (Jani)
- hpd A support from Ville
- various atomic polish all over (mostly from Maarten)
- first parts of virtualize gpu guest support on bdw from
Zhiyuan Lv
- GuC fixes from Alex
- polish for the chv clocks code (Ville)
- various things all over, as usual
* tag 'drm-intel-next-2015-09-11' of git://anongit.freedesktop.org/drm-intel: (145 commits)
drm/i915: Update DRIVER_DATE to 20150911
drm/i915: Remove one very outdated comment
drm/i915: Use crtc->state for duplication.
drm/i915: Do not handle a null plane state.
drm/i915: Remove legacy plane updates for cursor and sprite planes.
drm/i915: Use atomic state when changing cursor visibility.
drm/i915: Use the atomic state in intel_update_primary_planes.
drm/i915: Use the plane state in intel_crtc_info.
drm/i915: Use atomic plane state in the primary plane update.
drm/i915: add attached connector to hdmi container
drm/i915: don't hard code vlv backlight frequency if unset
drm/i915: initialize backlight max from VBT
drm/i915: use pch backlight override on hsw too
drm/i915/bxt: Clean up bxt_init_clock_gating
drm/i915: Fix cmdparser STORE/LOAD command descriptors
drm/i915: Dump pfit state as hex
drm/i915: access the PP_ON_DELAYS/PP_OFF_DELAYS regs only pre GEN5
drm/i915: access the PP_CONTROL reg only pre GEN5
drm/i915: Refactor common ringbuffer allocation code
drm/i915: use the yesno helper for logging
...
|
|
In order to cache the EDID properly for tiled displays, we
need to retrieve it before we register the connector with
userspace, otherwise userspace can call get resources
and try and get the edid before we've even cached it.
This fixes some problems when hotplugging mst monitors,
with X/mutter running. As mutter seems to get 0 modes
for one of the monitors in the tile.
v2: fix warning in radeon
handle tile setting in cached path rather than
get edid path.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Make adjusted_mode const whereever we don't have to modify it. This only
covers cases when we have a local adjusted_mode variable, and doesn't
make any difference for cases where we just dereference
pipe_config->adjusted_mode.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The adjustead_mode crtc_ timings are what we will program into the hardware,
so it's those timings we should be looking practically everywhere.
The normal and crtc_ timings should differ only when stere doubling is
used. In that case the normal timings are the orignal non-doubled
timigns, and crtc_ timings are the doubled timings used by the hardware.
The only case where we continue to look at the normal timings is when we
pass the adjusted_mode to drm_match_{cea,hdmi}_mode() to find the VIC.
drm_edid keeps the modes aronund in the non-double form only, so it
needs the non-double timings to match against.
Done with sed
's/adjusted_mode->\([vhVH]\)/adjusted_mode->crtc_\1/g'
's/adjusted_mode->clock/adjusted_mode->crtc_clock/g'
with a manual s/VDisplay/vdisplay/ within the comment in intel_dvo.c
v2: Update due to intel_dsi.c changes
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Backmerge to catch up with 4.3. slightly more involved conflict in the
irq code, but nothing beyond adjacent changes.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
connector->encoder is initialized as NULL. Fix this by setting it in
during pre enable. MST connectors are not read out during initial hw
readout, and have no fixed encoder mappings. So it's harmless to
return false when the connector has never been assigned to an encoder.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Backmerge -fixes since there's more DDI-E related cleanups on top of
the pile of -fixes for skl that just landed for 4.3.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i914/intel_dp.c
drivers/gpu/drm/i915/intel_lrc.c
Conflicts are all fairly harmless adjacent line stuff.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
