Age | Commit message (Collapse) | Author |
|
One of the things preventing us from using polling is the fact that
calling valleyview_crt_detect_hotplug() when there's a VGA cable
connected results in sending another hotplug. With polling enabled when
HPD is disabled, this results in a scenario like this:
- We enable power wells and reset the ADPA
- output_poll_exec does force probe on VGA, triggering a hpd
- HPD handler waits for poll to unlock dev->mode_config.mutex
- output_poll_exec shuts off the ADPA, unlocks dev->mode_config.mutex
- HPD handler runs, resets ADPA and brings us back to the start
This results in an endless irq storm getting sent from the ADPA
whenever a VGA connector gets detected in the middle of polling.
Somewhat based off of the "drm/i915: Disable CRT HPD around force
trigger" patch Ville Syrjälä sent a while back
Cc: stable@vger.kernel.org
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Lyude <cpaul@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit b236d7c8421969ac0693fc571e47ee5c2a62fb90)
|
|
While VGA hotplugging worked(ish) before, it looks like that was mainly
because we'd unintentionally enable it in
valleyview_crt_detect_hotplug() when we did a force trigger. This
doesn't work reliably enough because whenever the display powerwell on
vlv gets disabled, the values set in VLV_ADPA get cleared and
consequently VGA hotplugging gets disabled. This causes bugs such as one
we found on an Intel NUC, where doing the following sequence of
hotplugs:
- Disconnect all monitors
- Connect VGA
- Disconnect VGA
- Connect HDMI
Would result in VGA hotplugging becoming disabled, due to the powerwells
getting toggled in the process of connecting HDMI.
Changes since v3:
- Expose intel_crt_reset() through intel_drv.h and call that in
vlv_display_power_well_init() instead of
encoder->base.funcs->reset(&encoder->base);
Changes since v2:
- Use intel_encoder structs instead of drm_encoder structs
Changes since v1:
- Instead of handling the register writes ourself, we just reuse
intel_crt_detect()
- Instead of resetting the ADPA during display IRQ installation, we now
reset them in vlv_display_power_well_init()
Cc: stable@vger.kernel.org
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Lyude <cpaul@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Rebase over dev_priv/drm_device embedding.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 9504a89247595b6c066c68aea0c34af1fc78d021)
|
|
This lets call intel_crt_reset() in contexts where IRQs are disabled and
as such, can't hold the locks required to work with the connectors.
Cc: stable@vger.kernel.org
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Lyude <cpaul@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 28cf71ce3e206db1c3f30b3da31e7b48b2269e4c)
|
|
Version 1.01.
This firmware is made for Kabylake platform so it doesn't
need the stepping workaround that we had before.
v2: Rebased on top of latest nightly with min version
required change.
v3: With right CSR_VERSION (Patrik).
Cc: Christophe Prigent <christophe.prigent@intel.com>
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Reviewed-by: Ben Widawsky <benjamin.widawsky@intel.com> (v1)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461707991-15336-1-git-send-email-rodrigo.vivi@intel.com
(cherry picked from commit 4922d4919596219864686be1e70dcd92c685ec9f)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The i915 driver checks for color management properties changes as part
of a plane update. Therefore a color management update must imply a
plane update, otherwise we never update the transformation matrixes
and degamma/gamma LUTs.
v2: add comment about moving the commit of color management registers
to an async worker
v3: Commit color management register right after vblank
v4: Move back color management commit condition together with planes
commit
v5: Trigger color management commit through the planes commit (Daniel)
v6: Make plane change update more readable
Fixes: 20a34e78f0d7 (drm/i915: Update color management during vblank evasion.)
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: drm-intel-fixes@lists.freedesktop.org
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
References: https://lkml.org/lkml/2016/7/14/614
Reviewed-and-tested-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464183041-8478-1-git-send-email-lionel.g.landwerlin@intel.com
(cherry picked from commit e7852a4b3a4fb6f6c18fdaff934580aa8521599a)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
eDP should be treated as connected even if doesn't have an EDID. In that
case we'll use the timings from the VBT. That used to be the case until
commit f21a21983ef1 ("drm/i915: Splitting intel_dp_detect")
broke things by considering even eDP disconnected if we fail to get
an EDID for it.
Fix things up again by treating eDP as always connected.
Cc: Shubhangi Shrivastava <shubhangi.shrivastava@intel.com>
Cc: Nathan D Ciobanu <nathan.d.ciobanu@intel.com>
Cc: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Cc: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Cc: Larry Finger <larry.finger@lwfinger.net>
Reported-by: Larry Finger <larry.finger@lwfinger.net>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96675
Cc: drm-intel-fixes@lists.freedesktop.org
Fixes: f21a21983ef1 ("drm/i915: Splitting intel_dp_detect")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Larry Finger <larry.finger@lwfinger.net>
Link: http://patchwork.freedesktop.org/patch/msgid/1468836914-16537-1-git-send-email-ville.syrjala@linux.intel.com
(cherry picked from commit 1b7f2c8b0773d5ccbef43ef38a13ad33136c9679)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Some Kabylake SKUs are going to use Kabypoint PCH.
It is mainly for Halo and DT ones.
>From our specs it doesn't seem that KBP brings
any change on the display south engine. So let's consider
this as a continuation of SunrisePoint, i.e., SPT+.
Since it is easy to get confused by a letter change:
KBL = Kabylake - CPU/GPU codename.
KBP = Kabypoint - PCH codename.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96826
Link: http://patchwork.freedesktop.org/patch/msgid/1467418032-15167-1-git-send-email-rodrigo.vivi@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
(cherry picked from commit 22dea0be50b2eb0bafd3c82e1fb080113e0c889e)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
|
|
This patch enables a workaround for a mid thread preemption
issue where a hardware timing problem can prevent the
context restore from happening, leading to a hang.
v2: move to gen9_init_workarounds (Arun)
v3: move to start of gen9_init_workarounds (Arun)
Signed-off-by: Tim Gore <tim.gore@intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465816501-25557-1-git-send-email-tim.gore@intel.com
(cherry picked from commit a8ab5ed5e1bf856eceaab5579236de6f92822b9f)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
|
|
Add this fbc related workaround for all gen9
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-28-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit d1b4eefdea6d63aa15321f539feec298d8aefdc1)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
|
|
Bspec states that we need to set nuke on modify all to prevent
screen corruption with fbc on skl and kbl.
v2: proper workaround name
References: HSD#2227109, HSDES#1404569388
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-27-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit 031cd8c85aefad31e7af91eba7bc4735a6dfcc79)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
|
|
Set bit 8 in 0x43224 to prevent screen corruption and system
hangs on high memory bandwidth conditions. The same wa also suggest
setting bit 31 on ARB_CTL. According to another workaround we gain
better idle power savings when FBC is enabled.
v2: use correct workaround name
v3: split out overlapping wa for corruption avoidance (Ville)
References: HSD#2137218, HSD#2227171, HSD#2136579, BSID#883
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-26-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit 303d4ea522e8672a1b62d968a5b6764929adc292)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
|
|
According to bspec this prevents screen corruption when fbc is
used.
v2: This workaround has a name, use it (Ville)
v3: remove bogus gen check on ilk/vlv wm path (Ville)
References: HSD#2135555, HSD#2137270, BSID#562
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-25-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit 0f78dee6f06a9399d4bdf79575094cc761b872ac)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
|
|
This workaround for bdw and chv, is also needed for kbl A0.
References: HSD#1911519, BSID#569
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-24-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit 066d462888514af727008a450f4078b1a23d5cbe)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
|
|
Workaround for display underrun issues with Y & Yf Tiling.
Set this on all gen9 as stated by bspec.
v2: proper workaround name
References: HSD#2136383, BSID#857
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-22-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit 590e8ff04bc0182dce97228e5e352d6413d80456)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
|
|
This is needed for all kbl revision.
v2: Don't add revid checks to generic gen9 init (Arun)
References: HSD#2135593
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-21-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit 954337aa96a31f6d4baf1e40ac219fbb1b1d92f4)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
|
|
We need to disable clock gating in this unit to work around
hardware issue causing possible corruption/hang.
v2: name the bit (Ville)
v3: leave the fix enabled for 2227050 and set correct bit (Matthew)
v4: Split out the skl part in separate commit for easier backport
References: HSD#2227156, HSD#2227050
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-20-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit 4de5d7ccbccc88d2f7b1bcdc2180196ded7db8b8)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
|
|
Add this workaround for A0 and B0 revisions
References: HSD#2226935
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-19-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit 0b2d0934edceff9905b1202d0e7e91f1b6228485)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
|
|
Add this workaround for both bxt and kbl up to until
rev B0.
References: HSD#2136703
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-16-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit ad2bdb44b19529ba992bd0b7667e91b14fe9a9ee)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
|
|
Bspec states that we need to turn off dynamic credit
sharing on kbl revid a0 and b0. This happens by writing bit 28
on 0x4ab8.
References: HSD#2225601, HSD#2226938, HSD#2225763
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-15-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit c0b730d572ea00d427f6112b17982c6b9d5e97bb)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
|
|
According to bspec we need to disable gam unit clock gating on
on kbl revids A0 and B0.
References: HSD#2226858, HSD#1944358
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-14-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit 8aeb7f624fbf8a68a9c67f831d4158a0f80ea920)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
|
|
The bspec states that these must be set in CONFIG0 for all gen9.
v2: rebase
v3: fix spacing (Matthew)
References: HSD#2134995
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-13-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit b033bb6d5d3a0e51d56b3ba929a8db4e18da0892)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
|
|
Extend the scope of this workaround, already used in skl,
to also take effect in kbl.
v2: Fix KBL_REVID_E0 (Matthew)
References: HSD#2132677
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-12-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit fe90581987cd5fadd2942f59f8511bcb39fdec34)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
|
|
Add this workaround until upto kbl revid B0.
References: HSD#1802092
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-10-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit 9498dba7b4ffe40a1e2b23d7718b77e49841248f)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
|
|
Add this workaround for kbl revid A0 only.
v2: rebase
v3: carve out a non related workaround (Chris)
References: HSD#1911714
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-9-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit 8401d42fd5adf709281e1700194805f393b49573)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
|
|
We need this crucial workaround from skl also to all kbl revisions.
Lack of it was causing system hangs on skl enabling so this is
a must have.
v2: Don't add revid checks to gen9 init workarounds (Arun)
References: HSD#2126660
Cc: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-8-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit e587f6cb0af140f3c0ea794d8616eb9a29969983)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
|
|
Past evidence with system hangs and hsds tie
WaForceEnableNonCoherent and WaDisableHDCInvalidation to
WaForceContextSaveRestoreNonCoherent. Documentation
states that WaForceContextSaveRestoreNonCoherent would
not be needed on skl past E0 but evidence proved otherwise. See
commit <510650e8b2ab> ("drm/i915/skl: Fix spurious gpu hang with gt3/gt4
revs"). In this scope consider kbl to be skl with a bigger revision than
E0 so play it safe and bind these two workarounds to the
WaForceContextSaveRestoreNonCoherent, and apply to all gen9.
v2: fix comment (Matthew)
References: HSD#2134449, HSD#2131413
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-7-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit bbaefe72a00c93c6ec12e029019681e3f7d7de7a)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
|
|
The revision id range for this workaround has changed. So apply
it to all revids on all gen9.
References: HSD#2134449
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-6-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit 5b0e3659296cc4a1484e60640ef10780194a195b)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
|
|
We need this for kbl a0 boards. Note that this should be also
for bxt A0 but we omit that on purpose as bxt A0's are
out of fashion already.
References: HSD#1912158, HSD#4393097
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-5-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit 6e4f10c33a8bd0df4412bc31c0f11930e0228123)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
|
|
Add REVID macro for kbl to limit wa applicability to particular
revision range.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-4-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit c033a37cd42c1b5492d95bfbc8c0891088e04b57)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
|
|
Kabylake is part of gen9 family so init the generic gen9
workarounds for it.
v2: rebase
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-3-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit e5f81d65ac5a04020d790caf63b2324730ba0277)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
|
|
We need to disable clock gating in this unit to work around
hardware issue causing possible corruption/hang.
v2: name the bit (Ville)
v3: leave the fix enabled for 2227050 and set correct bit (Matthew)
References: HSD#2227156, HSD#2227050
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-2-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit eee8efb02a0f9284d85e6b3688f944ca765d7ad3)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
|
|
Kernel only need to add a register to HW whitelist, required for a
preemption related issue.
Reference: HSD#2131039
Reviewed-by: Jeff McGee <jeff.mcgee@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465203169-16591-1-git-send-email-arun.siluvery@linux.intel.com
(cherry picked from commit 6bb6285582e0cf9b3a8440e0e714aae5f66d9ce2)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
|
|
Found this while browsing Bspec. Looks like it applies to both skl and
kbl.
v2: Also for bxt (Art).
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Cc: "Pandiyan, Dhinakaran" <dhinakaran.pandiyan@intel.com>
Cc: "Runyan, Arthur J" <arthur.j.runyan@intel.com>
Reviewed-by: Sonika Jindal<sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463642060-30728-1-git-send-email-daniel.vetter@ffwll.ch
(cherry picked from commit dc00b6a07c2206e7b7dbcbeff856049264c40faa)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
|
|
Dell XPS 13 9350 apparently doesn't like it when we use the panel type
from OpRegion. The OpRegion panel type (0) tells us to use use low
vswing for eDP, whereas the VBT panel type (2) tells us to use normal
vswing. The problem is that low vswing results in some display flickers.
Since no one seems to know how this stuff is supposed to be handled,
let's just ignore the OpRegion panel type on SKL for now.
v2: Print the panel type correctly in the debug output
Reported-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: drm-intel-fixes@lists.freedesktop.org
References: https://lists.freedesktop.org/archives/intel-gfx/2016-June/098826.html
Fixes: a05628195a0d ("drm/i915: Get panel_type from OpRegion panel details")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1468324837-29237-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
(cherry picked from commit bb10d4ec3be4b069bfb61c60ca4f708f58f440f1)
[danvet: Fix up cherry-pick conflict with an s/dev_priv/dev/.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Prior to gen6 we didn't have per-ring IMR registers, which means that
since commit 61ff75ac20ff ("drm/i915: Simplify enabling
user-interrupts with L3-remapping") we're now masking off all interrupts
when init_render_ring() gets called. That's rather rude. Let's limit
the ring IMR frobbing to machines that actually have the per-ring IMR
registers.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: 61ff75ac20ff ("drm/i915: Simplify enabling user-interrupts with L3-remapping")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1468340687-3596-1-git-send-email-ville.syrjala@linux.intel.com
Reviewd-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit 035ea405c91e2dc89325a79129cf9af2b9c2ae8e)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Never go to sleep waiting on the GPU without first ensuring that we will
get woken up.
We have a choice of queuing the hangcheck before every schedule() or the
first time we wakeup. In order to simply accommodate both the signaler
and the ordinary waiter, move the queuing to the common point of
enabling the irq. We lose the paranoid safety of ensuring that the
hangcheck is active before the sleep, but avoid code duplication (and
redundant hangcheck queuing).
Testcase: igt/prime_busy
Fixes: c81d46138da6 ("drm/i915: Convert trace-irq to the breadcrumb waiter")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1468055535-19740-2-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
(cherry picked from commit 232af392fdb52aa2739dad4e03fed273b3c3f24a)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
In commit 7608a43d8f2e ("locking/mutexes: Use MUTEX_SPIN_ON_OWNER when
appropriate") the owner field in the mutex was updated from being
dependent upon CONFIG_SMP to using optimistic spin. Update our peek
function to suite.
Fixes:7608a43d8f2e ("locking/mutexes: Use MUTEX_SPIN_ON_OWNER...")
Reported-by: Hong Liu <hong.liu@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1468244777-4888-1-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
(cherry picked from commit 4f074a5393431a7d2cc0de7fcfe2f61d24854628)
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
igt/prime_vgem (and others) depends upon VGEM so automatically select it when
enabling i915 debugging.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1468059777-10205-1-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
|
|
igt/pm_rpm depends upon /dev/*/msr so automatically select it when
enabling i915 debugging.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1468054147-9821-1-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
|
|
One of the numerous VT-d workarounds we require is that the display
hardware reads past the end of the buffer triggering VT-d faults. This
is acknowledged in the code as being safe "since we fill the unused
portions of the GGTT with the scratch page". Alas, that is no longer
always true and so we trigger DMAR read faults.
Skylake also requires another workaround to avoid mixing VT-d and
unpopulated PTE, and so there we also need to ensure we fill unused
entries with the scratch page.
Reported-by: Mike Lothian <mike@fireburn.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96584
Fixes: f7770bfd9fd2 ("drm/i915: Skip clearing the GGTT on full-ppgtt systems")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: David Weinehall <david.weinehall@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466773634-8106-1-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: David Weinehall <david.weinehall@intel.com>
|
|
Some Kabylake SKUs are going to use Kabypoint PCH.
It is mainly for Halo and DT ones.
>From our specs it doesn't seem that KBP brings
any change on the display south engine. So let's consider
this as a continuation of SunrisePoint, i.e., SPT+.
Since it is easy to get confused by a letter change:
KBL = Kabylake - CPU/GPU codename.
KBP = Kabypoint - PCH codename.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96826
Link: http://patchwork.freedesktop.org/patch/msgid/1467418032-15167-1-git-send-email-rodrigo.vivi@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
This patch applies WaMediaPoolStateCmdInWABB which fixes
a problem with the restoration of thread counts on resuming
from RC6.
References: HSD#2137167
Signed-off-by: Tim Gore <tim.gore@intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467709290-5941-1-git-send-email-tim.gore@intel.com
|
|
Move the encoder cloning check to happen earlier in the modeset. The
main benefit will be that the debug output from a failed modeset will
be less confusing as output_types can not indicate an invalid
configuration during the later computation stages.
For instance, what happened to me was kms_setmode was attempting one
of its invalid cloning checks during which it asked for DP+VGA cloning
on HSW. In this case the DP .compute_config() was executed after
the FDI .compute_config() leaving the DP link clock (1.62 in this case)
in port_clock, and then later the FDI BW computation tried to use that
as the FDI link clock (which should always be 2.7). 1.62 x 2 wasn't
enough for the mode it was trying to use, and so it ended up rejecting
the modeset, not because of an invalid cloning configuration, but
because of supposedly running out of FDI bandwidth. Took me a while
to figure out what had actually happened.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466621833-5054-12-git-send-email-ville.syrjala@linux.intel.com
|
|
With the output_types bitmask there's no need to loop through
the encoders anymore when checking for HDMI+non-HDMI cloning.
v2: Use output_types bitmask
v3: Fix the logic to really check that there are no non-HDMI encoders
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> (v2)
Link: http://patchwork.freedesktop.org/patch/msgid/1466621833-5054-11-git-send-email-ville.syrjala@linux.intel.com
|
|
has_dsi_encoder was introduced to indicate that the pipe is driving
a DSI encoder. Now that we have the output_types bitmask that can
tell us the same thing, let's just kill has_dsi_encoder.
v2: Rebase, handle BXT DSI transcoder, rewrote commit message
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466621833-5054-10-git-send-email-ville.syrjala@linux.intel.com
|
|
INTEL_OUTPUT_DISPLAYPORT hsa been bugging me for a long time. It always
looks out of place besides INTEL_OUTPUT_EDP and INTEL_OUTPUT_DP_MST.
Let's just rename it to INTEL_OUTPUT_DP.
v2: Rebase
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466621833-5054-9-git-send-email-ville.syrjala@linux.intel.com
|
|
A bunch of places still look for DP encoders manually. Just call
intel_crtc_has_dp_encoder(). Note that many of these places don't
look for EDP or DP_MST, but it's still fine to replace them because
* for audio we don't enable audio on eDP anyway
* the code that lack DP MST check is only for plaforms that
don't support MST anyway
v2: Rebase
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466621833-5054-8-git-send-email-ville.syrjala@linux.intel.com
|
|
Use the new output_types bitmask instead of has_dp_encoder.
To make it less oainlful provide a small helper
(intel_crtc_has_dp_encoder()) to do the bitsy stuff.
v2: Rebase
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466621833-5054-7-git-send-email-ville.syrjala@linux.intel.com
|
|
Since we now have the output_types bitmaks in the crtc state, there's no
need to iterate through all the encoders to see if an LVDS or SDVO/HDMI
encoder might be present.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466621833-5054-6-git-send-email-ville.syrjala@linux.intel.com
|