| Age | Commit message (Collapse) | Author |
|---|
|
The audio configuration is only valid if the HDMI codec has been
properly set up. Do not attempt to set up audio before that happens
because it causes a division by zero.
Note that this is only problematic on Tegra20 and Tegra30. Later chips
implement the division instructions which return zero when dividing by
zero and don't throw an exception.
Fixes: db5adf4d6dce ("drm/tegra: hdmi: Fix audio to work with any pixel clock rate")
Reported-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
When CONFIG_IOMMU_API isn't set the following warnings pops up:
drivers/gpu/drm/tegra/vic.c: In function ‘vic_boot’:
drivers/gpu/drm/tegra/vic.c:110:31: error: implicit declaration of function ‘dev_iommu_fwspec_get’; did you mean ‘iommu_fwspec_free’? [-Werror=implicit-function-declaration]
struct iommu_fwspec *spec = dev_iommu_fwspec_get(vic->dev);
^~~~~~~~~~~~~~~~~~~~
iommu_fwspec_free
drivers/gpu/drm/tegra/vic.c:110:31: warning: initialization of ‘struct iommu_fwspec *’ from ‘int’ makes pointer from integer without a cast [-Wint-conversion]
drivers/gpu/drm/tegra/vic.c:117:19: error: ‘struct iommu_fwspec’ has no member named ‘num_ids’
if (spec && spec->num_ids > 0) {
^~
drivers/gpu/drm/tegra/vic.c:118:16: error: ‘struct iommu_fwspec’ has no member named ‘ids’
value = spec->ids[0] & 0xffff;
^~
Rework so that its inside a '#ifdef CONFIG_IOMMU_API' block.
Fixes: f3779cb190a5 ("drm/tegra: vic: Support stream ID register programming")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v5.1-rc1
This set of changes starts of with some refactoring of the CEC support
to make it reusable on Tegra210 and later. Following are a couple of
fixes for HDMI audio support (via HDA).
The bulk here is a set of preparatory patches working towards enabling
Tegra186 support for host1x and VIC. Additional patches will be needed
to fully enable this, but they're not quite ready yet.
To round things off, this also adds support for configuring the SOR
crossbar using device tree, and fixes a couple of job-related issues in
the host1x code.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thierry Reding <thierry.reding@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190208144721.25830-1-thierry.reding@gmail.com
|
|
The crossbar configuration is usually the same across all designs for a
given SoC generation. But sometimes there are designs that require some
other configuration.
Implement support for parsing the crossbar configuration from a device
tree. If the crossbar configuration is not present in the device tree,
fall back to the default crossbar configuration.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The version of VIC found in Tegra186 and later incorporates improvements
with regards to context isolation. As part of those improvements, stream
ID registers were added that allow to specify separate stream IDs for
the Falcon microcontroller and the VIC memory interface.
While it is possible to also set the stream ID dynamically at runtime to
allow userspace contexts to be completely separated, this commit doesn't
implement that yet. Instead, the static VIC stream ID is programmed when
the Falcon is booted. This ensures that memory accesses by the Falcon or
the VIC are properly translated via the SMMU.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Upon driver failure, the driver core will take care of clearing the
driver data, so there's no need to do so explicitly in the driver.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
On Tegra186 and later, the ARM SMMU provides an input address space that
is 48 bits wide. However, memory clients can only address up to 40 bits.
If the geometry is used as-is, allocations of IOVA space can end up in a
region that cannot be addressed by the memory clients.
To fix this, restrict the IOVA space to the DMA mask of the host1x
device. Note that, technically, the IOVA space needs to be restricted to
the intersection of the DMA masks for all clients that are attached to
the IOMMU domain. In practice using the DMA mask of the host1x device is
sufficient because all host1x clients share the same DMA mask.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Move initialization of the shared IOMMU domain after the host1x device
has been initialized. At this point all the Tegra DRM clients have been
attached to the shared IOMMU domain.
This is important because Tegra186 and later use an ARM SMMU, for which
the driver defers setting up the geometry for a domain until a device is
attached to it. This is to ensure that the domain is properly set up for
a specific ARM SMMU instance, which is unknown at allocation time.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Loading the firmware requires an allocation of IOVA space to make sure
that the VIC's Falcon microcontroller can read the firmware if address
translation via the SMMU is enabled.
However, the allocation currently happens at a time where the geometry
of an IOMMU domain may not have been initialized yet. This happens for
example on Tegra186 and later where an ARM SMMU is used. Domains which
are created by the ARM SMMU driver postpone the geometry setup until a
device is attached to the domain. This is because IOMMU domains aren't
attached to a specific IOMMU instance at allocation time and hence the
input address space, which defines the geometry, is not known yet.
Work around this by postponing the firmware load until it is needed at
the time where a channel is opened to the VIC. At this time the shared
IOMMU domain's geometry has been properly initialized.
As a byproduct this allows the Tegra DRM to be created in the absence
of VIC firmware, since the VIC initialization no longer fails if the
firmware can't be found.
Based on an earlier patch by Dmitry Osipenko <digetx@gmail.com>.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
|
|
Tegra DRM clients need access to their parent, so store a pointer to it
upon registration. It's technically possible to get at this by going via
the host1x client's parent and getting the driver data, but that's quite
complicated and not very transparent. It's much more straightforward and
natural to let the children know about their parent.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
|
|
Both macros evaluate to 0. At the same time flag is already set to
zero since the struct is kzalloc'd in framebuffer_alloc().
As called by drm_fb_helper_alloc_fbi() in the DRM drivers.
v2: Rebase and improve commit message per Emil's suggestion.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Sandy Huang <hjc@rock-chips.com>
Cc: "Heiko Stübner" <heiko@sntech.de>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Alexander Kapshuk <alexander.kapshuk@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: nouveau@lists.freedesktop.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-tegra@vger.kernel.org
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190124165831.16427-27-daniel.vetter@ffwll.ch
|
|
Having the probe helper stuff (which pretty much everyone needs) in
the drm_crtc_helper.h file (which atomic drivers should never need) is
confusing. Split them out.
To make sure I actually achieved the goal here I went through all
drivers. And indeed, all atomic drivers are now free of
drm_crtc_helper.h includes.
v2: Make it compile. There was so much compile fail on arm drivers
that I figured I'll better not include any of the acks on v1.
v3: Massive rebase because i915 has lost a lot of drmP.h includes, but
not all: Through drm_crtc_helper.h > drm_modeset_helper.h -> drmP.h
there was still one, which this patch largely removes. Which means
rolling out lots more includes all over.
This will also conflict with ongoing drmP.h cleanup by others I
expect.
v3: Rebase on top of atomic bochs.
v4: Review from Laurent for bridge/rcar/omap/shmob/core bits:
- (re)move some of the added includes, use the better include files in
other places (all suggested from Laurent adopted unchanged).
- sort alphabetically
v5: Actually try to sort them, and while at it, sort all the ones I
touch.
v6: Rebase onto i915 changes.
v7: Rebase once more.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Acked-by: CK Hu <ck.hu@mediatek.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: virtualization@lists.linux-foundation.org
Cc: etnaviv@lists.freedesktop.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: intel-gfx@lists.freedesktop.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Cc: nouveau@lists.freedesktop.org
Cc: spice-devel@lists.freedesktop.org
Cc: amd-gfx@lists.freedesktop.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-stm32@st-md-mailman.stormreply.com
Cc: linux-tegra@vger.kernel.org
Cc: xen-devel@lists.xen.org
Link: https://patchwork.freedesktop.org/patch/msgid/20190117210334.13234-1-daniel.vetter@ffwll.ch
|
|
The audio setting implementation was limited to a few specific pixel
clocks. This prevented HDMI audio from working on several test devices
as they need a pixel clock that is not supported by this implementation.
Fix this by implementing the algorithm provided in the TRM using fixed
point arithmetic. This allows the driver to cope with any sane pixel
clock rate.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
[treding@nvidia.com: fix uninitialized variable warning]
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Eliminate some duplicate code by reusing the HDA format parser already
used by the SOR.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This code can be reused for HDMI, so extract it into a reusable
function.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The HDA format data passed to the SOR from the HDA codec contains more
information than just the rate and number of channels. Parse all the
fields and store them in an internal structure for subsequent use.
While at it, also fix an off-by-one error in the number of channels.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Most of the CEC support code already lives in the "output" library code.
Move registration and unregistration to the library code as well to make
use of the same code with HDMI on Tegra210 and later via the SOR.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
drm-next has been forwarded to 5.0-rc1, and we need it to apply the damage
helper for dirtyfb series from Noralf Trønnes.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Make life easier for drivers by simply passing the connector
to drm_hdmi_avi_infoframe_from_display_mode() and
drm_hdmi_avi_infoframe_quant_range(). That way drivers don't
need to worry about is_hdmi2_sink mess.
v2: Make is_hdmi2_sink() return true for sil-sii8620
Adapt to omap/vc4 changes
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Sandy Huang <hjc@rock-chips.com>
Cc: "Heiko Stübner" <heiko@sntech.de>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: amd-gfx@lists.freedesktop.org
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Cc: nouveau@lists.freedesktop.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190108172828.15184-1-ville.syrjala@linux.intel.com
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.1:
UAPI Changes:
Cross-subsystem Changes:
- Turn dma-buf fence sequence numbers into 64 bit numbers
Core Changes:
- Move to a common helper for the DP MST hotplug for radeon, i915 and
amdgpu
- i2c improvements for drm_dp_mst
- Removal of drm_syncobj_cb
- Introduction of an helper to create and attach the TV margin properties
Driver Changes:
- Improve cache flushes for v3d
- Reflection support for vc4
- HDMI overscan support for vc4
- Add implicit fencing support for rockchip and sun4i
- Switch to generic fbdev emulation for virtio
Signed-off-by: Dave Airlie <airlied@redhat.com>
[airlied: applied amdgpu merge fixup]
From: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190107180333.amklwycudbsub3s5@flea
|
|
Follow the same pattern of locking as with other state objects. This
avoids boilerplate in the driver.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181022123122.30468-1-boris.brezillon@bootlin.com
|
|
If the SOR is already up and running when the kernel driver is probed,
setting a mode will typically fail. This can be seen for example on
Jetson TX2. Under certain circumstances the generic power domain code
will cause the SOR to be reset. However, if the power domain is never
powered off (this can happen if the HDA controller is enabled, which
is part of the same power domain as the SOR), then the SOR will end up
not getting reset and fail to properly set a mode.
To work around this, try to get the reset control and assert/deassert
it, irrespective of whether or not a generic power domain is attached
to the SOR. On platforms where the kernel implements generic power
domains (up to Tegra210) this will fail, because the power domain will
already have acquired an exclusive reference to the reset control. But
on recent platforms there the BPMP provides an ABI to control power
domains, it's possible to acquire the reset control from SOR and use
it to put the SOR into a known good state at probe time.
The proper solution for this is to make the SOR driver capable of
dealing with hardware that's already up and running (by first grace-
fully shutting it down, or perhaps by seamlessly transitioning to the
kernel driver and taking over the running display configuration). That
is fairly involved, though, so we'll go with this quickfix for now.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Remove the temporary workaround of storing the Tegra186 HDMI/DP I/O pad
ID in the SOR driver. The definition has long been available in the
soc/tegra/pmc.h header file.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This code is very similar to the audio over HDMI support on older chips.
Interoperation with the audio codec is done via a pair of codec scratch
registers and an interrupt that is raised at the SOR when the codec has
written those registers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Display controllers that don't own any windows and which therefore
aren't currently being assigned a primary plane are not registered
as a CRTC with the DRM framework. They request neither a syncpoint
nor an interrupt because they don't use them, so avoid cleaning up
those resources.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The display architecture on Tegra186 and Tegra194 requires that there be
some valid clock on all domains before accessing any display register. A
further requirement is that in addition to the host1x, hub, disp and dsc
clocks, all the head clocks (pclk0-2 on Tegra186 or pclk0-3 on Tegra194)
must also be enabled.
Implement this logic within the display hub driver to ensure the clocks
are always enabled at the right time.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The Video Image Composer (VIC) generation found on Tegra194 is backwards
compatible with its predecessor found on Tegra186.
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Before booting the Falcon processor, make sure to wait for memory
scrubbing to complete.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The ->alloc() callback in struct falcon_ops returns an ERR_PTR()-encoded
error code on failure, so it needs to be properly checked for, otherwise
subsequent code may dereference an invalid pointer.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Tegra supports generic PM domains on 64-bit ARM, and if that is enabled,
the power domain code will make sure that resets are asserted and
deasserted at appropriate points in time.
If generic PM domains are not implemented, such as on 32-bit Tegra, the
resets need to be asserted and deasserted explicitly by the driver.
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v4.20-rc1
This contains initial Tegra194 support as well as a couple of fixes for
DMA/IOMMU integration.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thierry Reding <thierry.reding@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180927205051.30017-1-thierry.reding@gmail.com
|
|
All Tegra DRM devices are getting attached to an implicit IOMMU DMA
domain if CONFIG_ARM_DMA_USE_IOMMU=y. Since Tegra DRM driver manages IOMMU
by itself, the devices must be detached from the implicit domain using
arch-specific IOMMU-API. Note that this works only for arm32 and not for
arm64, which will remain broken if CONFIG_IOMMU_DMA is enabled.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This patch unifies the naming of DRM functions for reference counting
of struct drm_device. The resulting code is more aligned with the rest
of the Linux kernel interfaces.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180926115640.24755-1-tzimmermann@suse.de
|
|
The SOR implemented in Tegra194 is subtly different from its predecessor
found in Tegra186. Most notably some registers have been moved around so
it is no longer compatible.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The DPAUX controller found on Tegra194 is almost identical to its
predecessor from Tegra186.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The display controllers found on Tegra194 are almost identical to those
found on Tegra186.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The display hub integrated into Tegra194 is almost identical to the one
found on Tegra186. However, it doesn't support DSC (display stream
compression) so it isn't fully compatible.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Tegra194 contains a fourth display controller that does not own any
windows. Therefore, we cannot currently assign a primary plane to it
which causes KMS to eventually crash. Do not register the display
controller if it owns no windows to work around this.
Note that we still have to enable and probe the display controller
because for some reason all display controllers need to be powered
(and/or clocked) before any registers can be accessed in any of the
display controllers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Some of definitions in the code changed the meaning, unfortunately one
place missed the change.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
convert drm_atomic_helper_suspend/resume() to use
drm_mode_config_helper_suspend/resume().
With this conversion, tegra_drm_fb_suspend() and
tegra_drm_fb_resume() will not be used anymore.
Both of these functions can be removed.
Also, in tegra_drm struct's member state will not be
used anymore. So this can be removed forever.
Fixed one sparse warning.
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Signed-off-by: Ajit Negi <ajitn.linux@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Kick out firmware fb when loading Tegra driver.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/b5c3972e5774d0d1f8887054a993bbc54e9dbe2a.1535810304.git.mirq-linux@rere.qmqm.pl
|
|
Pull drm updates from Dave Airlie:
"This is the main drm pull request for 4.19.
Rob has some new hardware support for new qualcomm hw that I'll send
along separately. This has the display part of it, the remaining pull
is for the acceleration engine.
This also contains a wound-wait/wait-die mutex rework, Peter has acked
it for merging via my tree.
Otherwise mostly the usual level of activity. Summary:
core:
- Wound-wait/wait-die mutex rework
- Add writeback connector type
- Add "content type" property for HDMI
- Move GEM bo to drm_framebuffer
- Initial gpu scheduler documentation
- GPU scheduler fixes for dying processes
- Console deferred fbcon takeover support
- Displayport support for CEC tunneling over AUX
panel:
- otm8009a panel driver fixes
- Innolux TV123WAM and G070Y2-L01 panel driver
- Ilitek ILI9881c panel driver
- Rocktech RK070ER9427 LCD
- EDT ETM0700G0EDH6 and EDT ETM0700G0BDH6
- DLC DLC0700YZG-1
- BOE HV070WSA-100
- newhaven, nhd-4.3-480272ef-atxl LCD
- DataImage SCF0700C48GGU18
- Sharp LQ035Q7DB03
- p079zca: Refactor to support multiple panels
tinydrm:
- ILI9341 display panel
New driver:
- vkms - virtual kms driver to testing.
i915:
- Icelake:
Display enablement
DSI support
IRQ support
Powerwell support
- GPU reset fixes and improvements
- Full ppgtt support refactoring
- PSR fixes and improvements
- Execlist improvments
- GuC related fixes
amdgpu:
- Initial amdgpu documentation
- JPEG engine support on VCN
- CIK uses powerplay by default
- Move to using core PCIE functionality for gens/lanes
- DC/Powerplay interface rework
- Stutter mode support for RV
- Vega12 Powerplay updates
- GFXOFF fixes
- GPUVM fault debugging
- Vega12 GFXOFF
- DC improvements
- DC i2c/aux changes
- UVD 7.2 fixes
- Powerplay fixes for Polaris12, CZ/ST
- command submission bo_list fixes
amdkfd:
- Raven support
- Power management fixes
udl:
- Cleanups and fixes
nouveau:
- misc fixes and cleanups.
msm:
- DPU1 support display controller in sdm845
- GPU coredump support.
vmwgfx:
- Atomic modesetting validation fixes
- Support for multisample surfaces
armada:
- Atomic modesetting support completed.
exynos:
- IPPv2 fixes
- Move g2d to component framework
- Suspend/resume support cleanups
- Driver cleanups
imx:
- CSI configuration improvements
- Driver cleanups
- Use atomic suspend/resume helpers
- ipu-v3 V4L2 XRGB32/XBGR32 support
pl111:
- Add Nomadik LCDC variant
v3d:
- GPU scheduler jobs management
sun4i:
- R40 display engine support
- TCON TOP driver
mediatek:
- MT2712 SoC support
rockchip:
- vop fixes
omapdrm:
- Workaround for DRA7 errata i932
- Fix mm_list locking
mali-dp:
- Writeback implementation
PM improvements
- Internal error reporting debugfs
tilcdc:
- Single fix for deferred probing
hdlcd:
- Teardown fixes
tda998x:
- Converted to a bridge driver.
etnaviv:
- Misc fixes"
* tag 'drm-next-2018-08-15' of git://anongit.freedesktop.org/drm/drm: (1506 commits)
drm/amdgpu/sriov: give 8s for recover vram under RUNTIME
drm/scheduler: fix param documentation
drm/i2c: tda998x: correct PLL divider calculation
drm/i2c: tda998x: get rid of private fill_modes function
drm/i2c: tda998x: move mode_valid() to bridge
drm/i2c: tda998x: register bridge outside of component helper
drm/i2c: tda998x: cleanup from previous changes
drm/i2c: tda998x: allocate tda998x_priv inside tda998x_create()
drm/i2c: tda998x: convert to bridge driver
drm/scheduler: fix timeout worker setup for out of order job completions
drm/amd/display: display connected to dp-1 does not light up
drm/amd/display: update clk for various HDMI color depths
drm/amd/display: program display clock on cache match
drm/amd/display: Add NULL check for enabling dp ss
drm/amd/display: add vbios table check for enabling dp ss
drm/amd/display: Don't share clk source between DP and HDMI
drm/amd/display: Fix DP HBR2 Eye Diagram Pattern on Carrizo
drm/amd/display: Use calculated disp_clk_khz value for dce110
drm/amd/display: Implement custom degamma lut on dcn
drm/amd/display: Destroy aux_engines only once
...
|
|
Merge changes in the PM core, system-wide PM infrastructure, generic
power domains (genpd) framework, ACPI PM infrastructure and cpuidle
for 4.19.
* pm-core:
driver core: Add flag to autoremove device link on supplier unbind
driver core: Rename flag AUTOREMOVE to AUTOREMOVE_CONSUMER
* pm-domains:
PM / Domains: Introduce dev_pm_domain_attach_by_name()
PM / Domains: Introduce option to attach a device by name to genpd
PM / Domains: dt: Add a power-domain-names property
* pm-sleep:
PM / reboot: Eliminate race between reboot and suspend
PM / hibernate: Mark expected switch fall-through
x86/power/hibernate_64: Remove VLA usage
PM / hibernate: cast PAGE_SIZE to int when comparing with error code
* acpi-pm:
ACPI / PM: save NVS memory for ASUS 1025C laptop
ACPI / PM: Default to s2idle in all machines supporting LP S0
* pm-cpuidle:
ARM: cpuidle: silence error on driver registration failure
|
|
rmk requested this for armada and I think we've had a few
conflicts build up.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Again to align with the usual prefix of just drm_connector_. Again
done with sed + manual fixup for indent issues.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180709084016.23750-7-daniel.vetter@ffwll.ch
|
|
Just makes it longer, and for most things in drm_connector.[hc] we
just use the drm_connector_ prefix. Done with sed + a bit of manual
fixup for the indenting.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180709084016.23750-6-daniel.vetter@ffwll.ch
|
|
Right now, the DRM panel logic returns NULL when a panel pointing to
the passed OF node is not present in the list of registered panels.
Most drivers interpret this NULL value as -EPROBE_DEFER, but we are
about to modify the semantic of of_drm_find_panel() and let the
framework return -ENODEV when the device node we're pointing to has
a status property that is not equal to "okay" or "ok".
Let's first patch the of_drm_find_panel() implementation to return
ERR_PTR(-EPROBE_DEFER) instead of NULL and patch all callers to replace
the '!panel' check by an 'IS_ERR(panel)' one.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180509130042.9435-2-boris.brezillon@bootlin.com
|
|
Now that we want to add another flag to autoremove the device link
on supplier unbind, it's fair to rename the existing flag from
DL_FLAG_AUTOREMOVE to DL_FLAG_AUTOREMOVE_CONSUMER so that we can
add similar flag for supplier later.
And, while we are touching device.h, fix a doc build warning.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Here we are checking for the buffer length, not an offset for writing
to, so using > is correct. The current code incorrectly rejects a
command buffer ending at the memory buffer's end.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
