| Age | Commit message (Collapse) | Author |
|---|
|
I'm not sure what made gcc warn about this code now. The 'ret' variable
does end up initialized in all cases, but it's definitely not obvious,
so the compiler is quite reasonable to warn about this.
So just add initialization to make it all much more obvious both to
compilers and to humans.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Adding device property "ccgx,firmware-build" for the CCGx
device, so the CCGx driver knows which firmware binary to
use for a specific vendor.
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The way of getting private imx_i2c_struct in i2c_imx_clk_notifier_call()
is incorrect, should use clk_change_nb element to get correct address
and avoid below kernel dump during POST_RATE_CHANGE notify by clk
framework:
Unable to handle kernel paging request at virtual address 03ef1488
pgd = (ptrval)
[03ef1488] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
Workqueue: events reduce_bus_freq_handler
PC is at i2c_imx_set_clk+0x10/0xb8
LR is at i2c_imx_clk_notifier_call+0x20/0x28
pc : [<806a893c>] lr : [<806a8a04>] psr: a0080013
sp : bf399dd8 ip : bf3432ac fp : bf7c1dc0
r10: 00000002 r9 : 00000000 r8 : 00000000
r7 : 03ef1480 r6 : bf399e50 r5 : ffffffff r4 : 00000000
r3 : bf025300 r2 : bf399e50 r1 : 00b71b00 r0 : bf399be8
Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 10c5387d Table: 4e03004a DAC: 00000051
Process kworker/2:1 (pid: 38, stack limit = 0x(ptrval))
Stack: (0xbf399dd8 to 0xbf39a000)
9dc0: 806a89e4 00000000
9de0: ffffffff bf399e50 00000002 806a8a04 806a89e4 80142900 ffffffff 00000000
9e00: bf34ef18 bf34ef04 00000000 ffffffff bf399e50 80142d84 00000000 bf399e6c
9e20: bf34ef00 80f214c4 bf025300 00000002 80f08d08 bf017480 00000000 80142df0
9e40: 00000000 80166ed8 80c27638 8045de58 bf352340 03ef1480 00b71b00 0f82e242
9e60: bf025300 00000002 03ef1480 80f60e5c 00000001 8045edf0 00000002 8045eb08
9e80: bf025300 00000002 03ef1480 8045ee10 03ef1480 8045eb08 bf01be40 00000002
9ea0: 03ef1480 8045ee10 07de2900 8045eb08 bf01b780 00000002 07de2900 8045ee10
9ec0: 80c27898 bf399ee4 bf020a80 00000002 1f78a400 8045ee10 80f60e5c 80460514
9ee0: 80f60e5c bf01b600 bf01b480 80460460 0f82e242 bf383a80 bf383a00 80f60e5c
9f00: 00000000 bf7c1dc0 80f60e70 80460564 80f60df0 80f60d24 80f60df0 8011e72c
9f20: 00000000 80f60df0 80f60e6c bf7c4f00 00000000 8011e7ac bf274000 8013bd84
9f40: bf7c1dd8 80f03d00 bf274000 bf7c1dc0 bf274014 bf7c1dd8 80f03d00 bf398000
9f60: 00000008 8013bfb4 00000000 bf25d100 bf25d0c0 00000000 bf274000 8013bf88
9f80: bf25d11c bf0cfebc 00000000 8014140c bf25d0c0 801412ec 00000000 00000000
9fa0: 00000000 00000000 00000000 801010e8 00000000 00000000 00000000 00000000
9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
9fe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000
[<806a893c>] (i2c_imx_set_clk) from [<806a8a04>] (i2c_imx_clk_notifier_call+0x20/0x28)
[<806a8a04>] (i2c_imx_clk_notifier_call) from [<80142900>] (notifier_call_chain+0x44/0x84)
[<80142900>] (notifier_call_chain) from [<80142d84>] (__srcu_notifier_call_chain+0x44/0x98)
[<80142d84>] (__srcu_notifier_call_chain) from [<80142df0>] (srcu_notifier_call_chain+0x18/0x20)
[<80142df0>] (srcu_notifier_call_chain) from [<8045de58>] (__clk_notify+0x78/0xa4)
[<8045de58>] (__clk_notify) from [<8045edf0>] (__clk_recalc_rates+0x60/0xb4)
[<8045edf0>] (__clk_recalc_rates) from [<8045ee10>] (__clk_recalc_rates+0x80/0xb4)
Code: e92d40f8 e5903298 e59072a0 e1530001 (e5975008)
---[ end trace fc7f5514b97b6cbb ]---
Fixes: 90ad2cbe88c2 ("i2c: imx: use clk notifier for rate changes")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
|
|
Change the iProc I2C driver to use the 'BIT' macro from all '1 << XXX'
bit operations to get rid of compiler warning and improve readability of
the code
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
- Replace explicit clock handling by Runtime PM calls,
- Streamline Runtime PM handling in error paths,
- Enable Runtime PM in .probe(),
- Disable Runtime PM in .remove(),
- Make sure the device is runtime-resumed when disabling interrupts in
.remove().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = devm_kzalloc(dev, sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = devm_kzalloc(dev, struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Peter Rosin <peda@axentia.se>
|
|
The behaviour, by default, to not deselect after each transfer is
unsafe when there is a device with an address that conflicts with
another device on another mux on the same parent bus, and it
may not be convenient to use devicetree to set the deselect mux,
e.g. when running on x86_64 when ACPI is used to discover most of the
device hierarchy.
Therefore, provide the ability to set the idle state behaviour using a
new sysfs file, idle_state as a complement to the method of
instantiating the device via sysfs. The possible behaviours are
disconnect, i.e. to deselect all channels from the mux, as-is (the
default), i.e. leave the last channel selected, and set a
predetermined channel.
The current behaviour of leaving the channel as-is after each
transaction is preserved.
Signed-off-by: Robert Shearman <robert.shearman@att.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
|
|
There are no in-tree users of the platform data, so remove it to
simplify the code slightly.
Remove the now unused pca954x.h platform data header.
Signed-off-by: Robert Shearman <robert.shearman@att.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
|
|
There are no in-tree users of the pca954x platform data and the
per-channel deselect configuration complicates efforts to export the
configuration to user-space in a way that could be applied to other
muxes. Therefore, remove support for the pca954x platform data.
Signed-off-by: Robert Shearman <robert.shearman@att.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
|
|
Some recent commits to this driver were trying to make sure the TSS
interrupt is not generated on busy system due to 25ms timer expiring
between commands. It can still happen, however if STOP command is not
issued on time at the end of the transmission. If wait_for_completion in
axxia_i2c_xfer_msg() would not return after 25ms of getting an
interrupt, TSS will be generated and idev->err_msg will be set to
-ETIMEDOUT which will be returned from the axxia_i2c_xfer_msg(), even
though the transfer did actually succeed (STOP is automatically issued
when TSS triggers).
Fortunately, apart from already used manual and sequence commands, the
controller also has so called auto command. It works just like manual
mode but it but an automatic STOP is issued when either transfer length
is met or NAK is received from slave device.
This patch changes the axxia_i2c_xfer_msg() function so that auto
command is used for last message in transaction letting hardware manage
issuing STOP. TSS is disabled just after command transferring last
message finishes. Auto command, just like sequence, ends with SS
interrupt instead of SNS so handling of both had to be unified.
The axxia_i2c_stop() is no longer needed as the transfer can only end
with following conditions:
- fully successful - then last message was send by AUTO command and STOP
was issued automatically
- NAK received - STOP is issued automatically by controller
- arbitration lost - STOP should not be issued as we don't control the
bus
- IP interrupt received - this is sent when transfer length is set to 0
for auto/sequence command. The check for that is done before START is
send so no STOP is required
- TSS received between commands - STOP is issued by the controller
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
If switching GPIOs does not sleep, then we can support atomic transfers.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Use the new xfer_atomic callback to check a newly introduced flag to
whitelist atomic transfers. This will report configurations which
worked accidently.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Use the new callback to reject atomic transfers.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The driver already has the routine in place, tie it to the new callback.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
By properly setting up the algorithm at probe time, we can skip the
check at every transfer. This allows us to get rid of the flags
completely.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The driver did handle this internally, convert it to use the new
callbacks.
Reviewed-by: Timo Alho <talho@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Add the master_xfer_atomic hook to enable i2c transactions in irq
disabled contexts like the poweroff case.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
[wsa: simplified code a little: 'timeout = !ret']
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
If the parent has an atomic callback, we need to translate it the same
way as the non-atomic callback.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
If the parent adapter has atomic_xfer callbacks, populate them for the
mux adapter as well. We can use the same translation function as for the
non-atomic xfer callback.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Reviewed-by Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
We had the request to access devices very late when interrupts are not
available anymore multiple times now. Mostly to prepare shutdown or
reboot. Allow adapters to specify a specific callback for this case.
Note that we fall back to the generic {master|smbus}_xfer callback if
this new atomic one is not present. This is intentional to preserve the
previous behaviour and avoid regressions. Because there are drivers not
using interrupts or because it might have worked "accidently" before.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Stefan Lengfeld <contact@stefanchrist.eu>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
If I2C transfers are executed in atomic contexts, trylock is used
instead of lock. This behaviour was missing for SMBUS, although a lot of
transfers are of SMBUS type, either emulated or direct. So, factor out
the locking routine into a helper and use it for I2C and SMBUS.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Commit cea443a81c9c ("i2c: Support i2c_transfer in atomic contexts")
added in_atomic() to the I2C core. However, the use of in_atomic()
outside of core kernel code is discouraged and was already[1] when this
code was added in early 2008. The above commit was a preparation for
commit b7a3670131c7 ("i2c-pxa: Add polling transfer"). Its commit
message says explicitly it was added "for cases where I2C transactions
have to occur at times interrup[t]s are disabled". So, the intention was
'disabled interrupts'. This matches the use cases for atomic I2C
transfers I have seen so far: very late communication (mostly to a PMIC)
to powerdown or reboot the system. For those cases, interrupts are
disabled then. It doesn't seem that in_atomic() adds value.
After a discussion with Peter Zijlstra[2], we came up with a better set
of conditionals to match the use case.
The I2C core will soon gain an extra callback into bus drivers
especially for atomic transfers to make them more generic. The code
deciding which transfer to use (atomic/non-atomic) should mimic the
behaviour which locking to use (trylock/lock). This is why we add a
helper for it.
[1] https://lwn.net/Articles/274695/
[2] http://patchwork.ozlabs.org/patch/1067437/
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Stefan Lengfeld <contact@stefanchrist.eu>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
No further occurences in the driver.
Fixes: dd1aa2524bc5 ("i2c: brcmstb: Add Broadcom settop SoC i2c controller driver")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Add i2c compatible for MT8183. Compare to MT2712 i2c controller,
MT8183 has different register offsets. Ltiming_reg is added to
adjust low width of SCL. Arb clock and dma_sync are needed.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
When i2c and apdma use different source clocks, we should enable
synchronization between them.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
When two i2c controllers are internally connected to the same
GPIO pins, the arb clock is needed to ensure that the waveforms
do not interfere with each other. And we also need to enable
the interrupt to find arb lost, old i2c controllers also have
the bit.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
New i2c registers would have different offsets, so we use different
offsets array to distinguish different i2c registers version.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Make sure to free the i2c adapter on the error exit path.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fixes: e1ab9a468e3b ("i2c: imx: improve the error handling in i2c_imx_dma_request()")
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Commit 54fb4a05af0a ("i2c: Check for ACPI resource conflicts") included
<linux/acpi.h> so we could use acpi_check_region(). Commit fd46a0064af1
("i2c: convert i2c-isch to platform_device") removed the use of
acpi_check_region() but not the include.
Remove the now-unnecessary include of <linux/acpi.h>. No functional change
intended.
Fixes: fd46a0064af1 ("i2c: convert i2c-isch to platform_device")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
"res" can't be NULL because it's a pointer to somewhere in the middle of
the "adev" struct. Also probe() succeeded so there is no need to check
here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Add NIC I2C support to the iProc I2C driver. Access to the NIC I2C base
registers requires going through the IDM wrapper to map into the NIC's
address space
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Use the following wrapper for read/write access of iProc i2c registers:
u32 iproc_i2c_rd_reg(struct bcm_iproc_i2c_dev *iproc_i2c,
u32 offset)
void iproc_i2c_wr_reg(struct bcm_iproc_i2c_dev *iproc_i2c, u32 offset,
u32 val)
This preps the driver for support of indirect register access required
by certain SoCs with this iProc I2C block integrated
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Add polling support to the iProc I2C driver. Polling mode is
activated when the driver fails to obtain an interrupt ID from device
tree
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Add support for more master error status including FIFO underrun and RX
FIFO full
Signed-off-by: Michael Cheng <ccheng@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Add slave mode support to the iProc I2C driver.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Michael Cheng <ccheng@broadcom.com>
Signed-off-by: Shreesha Rajashekar <shreesha.rajashekar@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Add support to allow I2C master read transfer up to 255 bytes.
Signed-off-by: Shreesha Rajashekar <shreesha@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Instead of using custom variables and parser, convert the driver to use
the ones provided by I2C core.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
MP2 controllers have two separate busses, so may accommodate up to two I2C
adapters. Those adapters are listed in the ACPI namespace with the
"AMDI0011" HID, and probed by a platform driver.
Communication with the MP2 takes place through MMIO registers, or through
DMA for more than 32 bytes transfers.
This is major rework of the patch submitted by Nehal-bakulchandra Shah from
AMD (https://patchwork.kernel.org/patch/10597369/).
Most of the event handling of v3 was rewritten to make it work with more
than one bus (e.g on Ryzen-based Lenovo Yoga 530), and this version
contains many other improvements.
Signed-off-by: Elie Morisse <syniurge@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Slave mode driver is based on the concept of i2c-designware driver.
Signed-off-by: Juergen Fitschen <me@jue.yt>
[ludovic.desroches@microchip.com: rework Kconfig and replace IS_ENABLED
by defined]
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The single file i2c-at91.c has been split into core code (i2c-at91-core.c)
and master mode specific code (i2c-at91-master.c). This should enhance
maintainability and reduce ifdeffery for slave mode related code.
The code itself hasn't been touched. Shared functions only had to be made
non-static. Furthermore, includes have been cleaned up.
Signed-off-by: Juergen Fitschen <me@jue.yt>
[ludovic.desroches@microchip.com: fix checkpatch errors and use SPDX]
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
In order to implement slave mode support for the at91 hardware we have to
segregate all master mode specific function parts from the general parts.
The upcoming slave mode patch will call its sepcific probe resp. init
function instead of the master mode functions after the shared general
code has been executed.
This concept has been influenced by the i2c-designware driver.
Signed-off-by: Juergen Fitschen <me@jue.yt>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
When sending with DMA, the driver transfers the first byte with PIO (as
documented). However, it started DMA right after the first byte was
written. This worked, but was not according to the datasheet which
suggests to wait until data register was empty again. Implement this.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
We will need to know if enabling DMA was successful in a later patch.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Use a macro for the hardcoded value and apply a build check. If it is
not met, the driver logic will not work anymore.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This avoids useless loops inside the I2C timing algorithm.
Actually, we support only one possible solution per prescaler value.
So after finding a solution with a prescaler, the algorithm can
switch directly to the next prescaler value.
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The Synopsys I2C Controller has an interface clock, but most SoCs hide
this away. However, on some SoCs you need to explicitly enable the
interface clock in order to access the registers. Therefore, add
support for an optional interface clock.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Gareth Williams <gareth.williams.jx@renesas.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Add PCI ID for Intel Comet Lake PCH.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Before this commit the i2c-designware-platdrv assumes that if the pdev
has an apci-companion it should use a dynamic adapter-nr and it sets
adapter->nr to -1, otherwise it will use pdev->id as adapter->nr.
There are 3 ways how platform_device-s to which i2c-designware-platdrv
will bind can be instantiated:
1) Through of / devicetree
2) Through ACPI enumeration
3) Explicitly instantiated through platform_device_create + add
1) In case of devicetree-instantiation the drivers/of code always sets
pdev->id to PLATFORM_DEVID_NONE, which is -1 so in this case both paths
to set adapter->nr end up doing the same thing.
2) In case of ACPI instantiation the device will always have an
ACPI-companion, so we are already using dynamic adapter-nrs.
3) There are 2 places manually instantiating a designware_i2c platform_dev:
drivers/mfd/intel_quark_i2c_gpio.c
drivers/mfd/intel-lpss.c
In the intel_quark_i2c_gpio.c case pdev->id is always 0, so switching to
dynamic adapter-nrs here could lead to the bus-number no longer being
stable, but the quark X1000 only has 1 i2c-controller, which will also
be assigned bus-number 0 when using dynamic adapter-nrs.
In the intel-lpss.c case intel_lpss_probe() is called from either
intel-lpss-acpi.c in which case there always is an ACPI-companion, or
from intel-lpss-pci.c. In most cases devices handled by intel-lpss-pci.c
also have an ACPI-companion, so we use a dynamic adapter-nr. But in some
cases the ACPI-companion is missing and we would use pdev->id (allocated
from intel_lpss_devid_ida). Devices which use the intel-lpss-pci.c code
typically have many i2c busses, so using pdev->id in this case may lead
to a bus-number conflict, triggering a WARN(id < 0, "couldn't get idr")
in i2c-core-base.c causing an oops an the adapter registration to fail.
So in this case using non dynamic adapter-nrs is actually undesirable.
One machine on which this oops was triggering is the Apollo Lake based
Acer TravelMate Spin B118.
TL;DR: Switching to always using dynamic adapter-numbers does not make
any difference in most cases and in the one case where it does make a
difference the behavior change is desirable because the old behavior
caused an oops.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1687065
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
i2c-designware-platdrv assumes that if the pdev has an apci-companion
it should use a dynamic adapter-nr and otherwise it will use pdev->id
as adapter-nr.
Before this commit the setting of the adapter.nr was somewhat convoluted,
in the acpi_companion case it was set from dw_i2c_acpi_configure, in the
non acpi_companion case it was set from dw_i2c_set_fifo_size based on
tx_fifo_depth not being set yet indicating that dw_i2c_acpi_configure was
not executed.
This cleans this up, directly setting the adapter-nr from
dw_i2c_plat_probe for both cases.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Make sure we report 'no buffer' for 0-length messages. This can only
happen if threshold is set to 0 which is kind of bogus but we should
still handle this situation. Update the docs and add a debug message
to educate callers of this function.
Reported-by: Hsin-Yi Wang <hsinyi@chromium.org>
Fixes: e94bc5d18be0 ("i2c: add helpers to ease DMA handling")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
