summaryrefslogtreecommitdiff
path: root/drivers/input/touchscreen
AgeCommit message (Collapse)Author
2022-01-08Input: zinitix - add compatible for bt532Nikita Travkin
Zinitix BT532 is another touch controller that seem to implement the same interface as an already supported BT541. Add it to the driver. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Nikita Travkin <nikita@trvn.ru> Link: https://lore.kernel.org/r/20220106072840.36851-5-nikita@trvn.ru Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2022-01-08Input: zinitix - handle proper supply namesLinus Walleij
The supply names of the Zinitix touchscreen were a bit confused, the new bindings rectifies this. To deal with old and new devicetrees, first check if we have "vddo" and in case that exists assume the old supply names. Else go and look for the new ones. We cannot just get the regulators since we would get an OK and a dummy regulator: we need to check explicitly for the old supply name. Use struct device *dev as a local variable instead of the I2C client since the device is what we are actually obtaining the resources from. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> [Slightly changed the legacy regulator detection] Signed-off-by: Nikita Travkin <nikita@trvn.ru> Link: https://lore.kernel.org/r/20220106072840.36851-4-nikita@trvn.ru Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-12-19Input: ucb1400_ts - remove redundant variable penupColin Ian King
Variable penup is assigned a value but penup is never read later, it is redundant and can be removed. Signed-off-by: Colin Ian King <colin.i.king@gmail.com> Link: https://lore.kernel.org/r/20211205000525.153999-1-colin.i.king@gmail.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-12-19Input: ti_am335x_tsc - lower the X and Y sampling timeDario Binacchi
The open delay time has to be applied only on the first sample of the X/Y coordinates because on the following samples the ADC channel is not changed. Removing this time from the samples after the first one, "ti,coordinate-readouts" greater than 1, decreases the total acquisition time, allowing to increase the number of acquired coordinates in the time unit. Signed-off-by: Dario Binacchi <dariobin@libero.it> Link: https://lore.kernel.org/r/20211212125358.14416-4-dariobin@libero.it Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-12-19Input: ti_am335x_tsc - fix STEPCONFIG setup for Z2Dario Binacchi
The Z2 step configuration doesn't erase the SEL_INP_SWC_3_0 bit-field before setting the ADC channel. This way its value could be corrupted by the ADC channel selected for the Z1 coordinate. Fixes: 8c896308feae ("input: ti_am335x_adc: use only FIFO0 and clean up a little") Signed-off-by: Dario Binacchi <dariobin@libero.it> Link: https://lore.kernel.org/r/20211212125358.14416-3-dariobin@libero.it Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-12-19Input: ti_am335x_tsc - set ADCREFM for X configurationDario Binacchi
As reported by the STEPCONFIG[1-16] registered field descriptions of the TI reference manual, for the ADC "in single ended, SEL_INM_SWC_3_0 must be 1xxx". Unlike the Y and Z coordinates, this bit has not been set for the step configuration registers used to sample the X coordinate. Fixes: 1b8be32e6914 ("Input: add support for TI Touchscreen controller") Signed-off-by: Dario Binacchi <dariobin@libero.it> Link: https://lore.kernel.org/r/20211212125358.14416-2-dariobin@libero.it Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-12-12Input: silead - add pen supportHans de Goede
Some Silead touchscreens have support for an active (battery powered) pen, add support for this. So far pen-support has only been seen on X86/ACPI (non devicetree) devs, IOW it is not used in actual devicetree files. The devicetree-bindings maintainers have requested properties like these to not be added to the devicetree-bindings, so the new properties are deliberately not added to the existing silead devicetree-bindings documentation. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20211122220637.11386-3-hdegoede@redhat.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-12-12Input: silead - add support for EFI-embedded fw using different min/max ↵Hans de Goede
coordinates Unfortunately, at the time of writing this commit message, we have been unable to get permission from Silead, or from device OEMs, to distribute the necessary Silead firmware files in linux-firmware. On a whole bunch of devices the UEFI BIOS code contains a touchscreen driver, which contains an embedded copy of the firmware. The fw-loader code has a "platform" fallback mechanism, which together with info on the firmware from drivers/platform/x86/touchscreen_dmi.c will use the firmware from the UEFI driver when the firmware is missing from /lib/firmware. This makes the touchscreen work OOTB without users needing to manually download the firmware. The firmware bundled with the original Windows/Android is usually newer then the firmware in the UEFI driver and it is better calibrated. This better calibration can lead to significant differences in the reported min/max coordinates. Add support for a new (optional) "silead,efi-fw-min-max" property which provides a set of alternative min/max values to use for the x/y axis when the EFI embedded firmware is used. The new property is only used on (x86) devices which do not use devicetree, IOW it is not used in actual devicetree files. The devicetree-bindings maintainers have requested properties like these to not be added to the devicetree-bindings, so the new property is deliberately not added to the existing silead devicetree-bindings documentation. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20211122220637.11386-2-hdegoede@redhat.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-12-12Input: goodix - 2 small fixes for pen supportHans de Goede
2 small fixes for pen support 1. Set the id.vendor field for the pen input_dev 2. Fix a typo in a comment Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20211212124242.81019-5-hdegoede@redhat.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-12-12Input: goodix - improve gpiod_get() error loggingHans de Goede
goodix_get_gpio_config() errors are fatal (abort probe()) so log them at KERN_ERR level rather then as debug messages. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20211212124242.81019-4-hdegoede@redhat.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-12-09Input: goodix - add pen supportHans de Goede
Some Goodix touchscreens have support for a (Goodix) active pen, add support for this. The info on how to detect when a pen is down and to detect when the stylus buttons are pressed was lifted from the out of tree Goodix driver with pen support written by Adya: https://gitlab.com/AdyaAdya/goodix-touchscreen-linux-driver/ Since there is no way to tell if pen support is present, the registering of the pen input_dev is delayed till the first pen event is detected. This has been tested on a Trekstor Surftab duo W1, a Chuwi Hi13 and a Cyberbook T116 tablet. BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=202161 BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=204513 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20211207100754.31155-3-hdegoede@redhat.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-12-08Merge tag 'v5.15' into nextDmitry Torokhov
Sync up with the mainline to get the latest APIs and DT bindings.
2021-11-29Input: wacom_i2c - clean up the query device fieldsAlistair Francis
Improve the query device fields to be more verbose. Signed-off-by: Alistair Francis <alistair@alistair23.me> Link: https://lore.kernel.org/r/20211118123545.102872-1-alistair@alistair23.me Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-11-09Input: wacom_i2c - use macros for the bit masksAlistair Francis
To make the code easier to read use macros for the bit masks. Signed-off-by: Alistair Francis <alistair@alistair23.me> Link: https://lore.kernel.org/r/20211009113707.17568-2-alistair@alistair23.me Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-11-09Input: ili210x - reduce sample period to 15msMarek Vasut
Modern devices may redraw display at 60 Hz, make sure we have one input sample per one frame. Reduce sample period to 15ms, so we would get up to 66.6 samples per second, although realistically with all the jitter and extra scheduling wiggle room, we would end up just above 60 samples per second. This should be a good compromise between sampling too often and sampling too seldom. Signed-off-by: Marek Vasut <marex@denx.de> Link: https://lore.kernel.org/r/20211108114145.84118-1-marex@denx.de Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-11-09Input: ili210x - improve polled sample spacingMarek Vasut
Currently the ili210x driver implements a threaded interrupt handler which starts upon edge on the interrupt line, and then polls the touch controller for samples. Every time a sample is obtained from the controller, the thread function checks whether further polling is required, and if so, waits fixed amount of time before polling for next sample. The delay between consecutive samples can thus vary greatly, because the I2C transfer required to retrieve the sample from the controller takes different amount of time on different platforms. Furthermore, different models of the touch controllers supported by this driver require different delays during retrieval of samples too. Instead of waiting fixed amount of time before polling for next sample, determine how much time passed since the beginning of sampling cycle and then wait only the remaining amount of time within the sampling cycle. This makes the driver deliver samples with equal spacing between them. Signed-off-by: Marek Vasut <marex@denx.de> Link: https://lore.kernel.org/r/20211108005216.480525-1-marex@denx.de Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-11-09Input: ili210x - special case ili251x sample read outMarek Vasut
The ili251x touch controller needs 5ms delay between sending I2C device address and register address, and, writing or reading register data. According to downstream ili251x example code, this 5ms delay is not required when reading touch samples out of the controller. Implement such a special case. Signed-off-by: Marek Vasut <marex@denx.de> Link: https://lore.kernel.org/r/20211108005259.480545-1-marex@denx.de Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-10-17Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input Pull input fixes from Dmitry Torokhov: - a new product ID for the xpad joystick driver - fixes to resistive-adc-touch and snvs_pwrkey drivers - a change to touchscreen helpers to make clang happier * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: touchscreen - avoid bitwise vs logical OR warning Input: xpad - add support for another USB ID of Nacon GC-100 Input: resistive-adc-touch - fix division by zero error on z1 == 0 Input: snvs_pwrkey - add clk handling
2021-10-16Input: ili210x - add ili251x firmware update supportMarek Vasut
The ili251x firmware can be updated, this is used when switching between different modes of operation of the touch surface, e.g. glove operation. This patch implements the firmware update mechanism triggered by a write into an sysfs attribute. The firmware itself is distributed as an intel hex file with non-standard types. The first two lines are of type 0xad, which indicates the start of DataFlash payload, that is always at address 0xf000 on the ili251x, so it can be dropped, and 0xac which indicates the position of firmware info in the Application payload, that is always at address 0x2020 on the ili251x and we do not care. The rest of the firmware is data of type 0x00, and we care about that. To convert the firmware hex file into something usable by the kernel, remove the first two lines and then use ihex2fw: $ tail -n +3 input.hex > temp.hex $ ./tools/firmware/ihex2fw temp.hex firmware/ilitek/ili251x.bin To trigger the firmware update, place firmware file ilitek/ili251x.bin into /lib/firmware/, write into firmware_update sysfs attribute and wait about 30-40 seconds. The firmware update is slow. Afterward, verify the firmware_version and mode sysfs attributes to check whether the firmware got updated and the controller switched back to application (AP) mode by reading out 'mode' attribute in sysfs. Note that the content of firmware_version, e.g. 0600.0005.abcd.aa04 can be matched to the content of the firmware hex file. The first four bytes, 0x06 0x00 0x00 0x05 can be found at ^:102030 00 05000006, the next four bytes 0xab 0xcd 0xaa 0x04 at ^:10F000 00 nnnnnnnn ABCDAA04. Note that the protocol differs considerably between the ili2xxx devices, this patch therefore implements this functionality only for ili251x that I can test. Signed-off-by: Marek Vasut <marex@denx.de> Link: https://lore.kernel.org/r/20210831202506.181927-3-marex@denx.de Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-10-16Input: ili210x - export ili251x version details via sysfsMarek Vasut
The ili251x firmware protocol permits readout of firmware version, protocol version, mcu version and current mode (application, boot loader, forced update). These information are useful when updating the firmware on the il251x, e.g. to avoid updating the same firmware into the device multiple times. The locking is now necessary to avoid races between interrupt handler and the sysfs readouts. Note that the protocol differs considerably between the ili2xxx devices, this patch therefore implements this functionality only for ili251x that I can test. Signed-off-by: Marek Vasut <marex@denx.de> Link: https://lore.kernel.org/r/20210831202506.181927-2-marex@denx.de Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-10-16Input: ili210x - use resolution from ili251x firmwareMarek Vasut
The ili251x firmware protocol permits readout of panel resolution, implement this, but make it possible to override this value using DT bindings. This way, older DTs which contain touchscreen-size-x and touchscreen-size-y properties will behave just like before and new DTs may avoid specifying these for ILI251x. Note that the command format is different on other controllers, so this functionality is isolated to ILI251x. Signed-off-by: Marek Vasut <marex@denx.de> Link: https://lore.kernel.org/r/20210831202506.181927-1-marex@denx.de Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-10-15Input: resistive-adc-touch - fix division by zero error on z1 == 0Oleksij Rempel
For proper pressure calculation we need at least x and z1 to be non zero. Even worse, in case z1 we may run in to division by zero error. Fixes: 60b7db914ddd ("Input: resistive-adc-touch - rework mapping of channels") Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Link: https://lore.kernel.org/r/20211007095727.29579-1-o.rempel@pengutronix.de Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-10-15Input: ads7846 - do not attempt IRQ workaround when deferring probeDmitry Torokhov
When request_irq() returns -EPORBE_DEFER we should abort probe and try again later instead of trying to engage IRQ trigger workaround. Link: https://lore.kernel.org/r/20210910045039.4020199-3-dmitry.torokhov@gmail.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-10-15Input: ads7846 - use input_set_capability()Dmitry Torokhov
Instead of manipulating capability bits directly use input_set_capability(). Also stop setting EV_ABS explicitly as input_set_abs_params() does it for us. Link: https://lore.kernel.org/r/20210910045039.4020199-2-dmitry.torokhov@gmail.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-10-15Input: ads7846 - set input device bus type and product IDDmitry Torokhov
Set input device's bus type as BUS_SPI and use model as product ID. Link: https://lore.kernel.org/r/20210910045039.4020199-1-dmitry.torokhov@gmail.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-10-12Input: tsc200x - make tsc200x_remove() return voidUwe Kleine-König
Up to now tsc200x_remove() returns zero unconditionally. Make it return void instead which makes it easier to see in the callers that there is no error to handle. Also the return value of i2c and spi remove callbacks is ignored anyway. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Link: https://lore.kernel.org/r/20211012153945.2651412-7-u.kleine-koenig@pengutronix.de Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-10-11Input: st1232 - prefer asynchronous probingJohn Keeping
The device may take up to 100ms to become responsive during probe, so prefer asynchronous probing to avoid delaying the rest of the system. Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: John Keeping <john@metanate.com> Link: https://lore.kernel.org/r/20211007111217.1935858-1-john@metanate.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-10-11Input: st1232 - increase "wait ready" timeoutJohn Keeping
I have a ST1633 touch controller which fails to probe due to a timeout waiting for the controller to become ready. Increasing the minimum delay to 100ms ensures that the probe sequence completes successfully. The ST1633 datasheet says nothing about the maximum delay here and the ST1232 I2C protocol document says "wait until" with no notion of a timeout. Since this only runs once during probe, being generous with the timout seems reasonable and most likely the device will become ready eventually. (It may be worth noting that I saw this issue with a PREEMPT_RT patched kernel which probably has tighter wakeups from usleep_range() than other preemption models.) Fixes: f605be6a57b4 ("Input: st1232 - wait until device is ready before reading resolution") Signed-off-by: John Keeping <john@metanate.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20210929152609.2421483-1-john@metanate.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-09-22Input: raydium_i2c_ts - make use of the helper function ↵Cai Huoqing
devm_add_action_or_reset() The helper function devm_add_action_or_reset() will internally call devm_add_action(), and if devm_add_action() fails then it will execute the action mentioned and return the error code. So use devm_add_action_or_reset() instead of devm_add_action() to simplify the error handling, reduce the code. Signed-off-by: Cai Huoqing <caihuoqing@baidu.com> Link: https://lore.kernel.org/r/20210922125212.95-3-caihuoqing@baidu.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-09-22Input: elants_i2c - make use of devm_add_action_or_reset()Cai Huoqing
The helper function devm_add_action_or_reset() will internally call devm_add_action(), and if devm_add_action() fails then it will execute the action mentioned and return the error code. So use devm_add_action_or_reset() instead of devm_add_action() to simplify the error handling, reduce the code. Signed-off-by: Cai Huoqing <caihuoqing@baidu.com> Link: https://lore.kernel.org/r/20210922125212.95-2-caihuoqing@baidu.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-09-20Input: goodix - add support for controllers without flashHans de Goede
Some Goodix touchscreen controllers, such as for example the GT912, don't have flash-storage for their firmware. These models require the OS to load the firmware at runtime, as well as some other special handling. Add support for this to the goodix driver. This patch was developed and tested on a Glavey TM800A550L tablet. Note the "goodix,main-clk" and "firmware-name" device-properties used by the new code are *not* documented in the Documentation/devicetree/bindings/input/touchscreen/goodix.yaml device-tree bindings for now. Not documenting these is intentional. This is done because this code has only been tested on x86/ACPI so far, where devicetree is not used. Instead these properties are set through a software-fwnode attached to the device by the drivers/platform/x86/touchscreen_dmi.c code. This means that the use of this properties for now is purely a kernel-internal thing and the name/working of the properties may still be changed for now. Reviewed-by: Bastien Nocera <hadess@hadess.net> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20210920150643.155872-7-hdegoede@redhat.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-09-20Input: goodix - allow specifying the config filenameHans de Goede
The config which needs to be send to the controller on some device-models is model-specific. Allow specifying a model-specific filename through a device-property, rather then always using a fixed filename. Note the "goodix,config-name" device-property used by this is *not* documented in the Documentation/devicetree/bindings/input/touchscreen/goodix.yaml device-tree bindings for now. Not documenting these is intentional. This is done because this code has only been tested on x86/ACPI so far, where devicetree is not used. Instead these properties are set through a software-fwnode attached to the device by the drivers/platform/x86/touchscreen_dmi.c code. This means that the use of this property for now is purely a kernel-internal thing and the name/working of the property may still be changed for now. Reviewed-by: Bastien Nocera <hadess@hadess.net> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20210920150643.155872-6-hdegoede@redhat.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-09-20Input: goodix - push error logging up into i2c_read and i2c_write helpersHans de Goede
Make the goodix_i2c_read() and goodix_i2c_write*() helpers log errors themselves. This allows removing all the error logging from their callers. This already results in a nice cleanup with the current code and it also helps to make the upcoming support for controllers without flash cleaner. Reviewed-by: Bastien Nocera <hadess@hadess.net> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20210920150643.155872-5-hdegoede@redhat.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-09-20Input: goodix - refactor reset handlingHans de Goede
Refactor reset handling a bit, change the main reset handler into a new goodix_reset_no_int_sync() helper and add a goodix_reset() wrapper which calls goodix_int_sync() separately. Also push the dev_err() call on reset failure into the goodix_reset_no_int_sync() and goodix_int_sync() functions, so that we don't need to have separate dev_err() calls in all their callers. This is a preparation patch for adding support for controllers without flash, which need to have their firmware uploaded and need some other special handling too. Reviewed-by: Bastien Nocera <hadess@hadess.net> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20210920150643.155872-4-hdegoede@redhat.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-09-20Input: goodix - add a goodix.h header fileHans de Goede
Add a goodix.h header file, and move the register definitions, and struct declarations there and add prototypes for various helper functions. This is a preparation patch for adding support for controllers without flash, which need to have their firmware uploaded and need some other special handling too. Since MAINTAINERS needs updating because of this change anyways, also add myself as co-maintainer. Reviewed-by: Bastien Nocera <hadess@hadess.net> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20210920150643.155872-3-hdegoede@redhat.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-09-20Input: goodix - change goodix_i2c_write() len parameter type to intHans de Goede
Change the type of the goodix_i2c_write() len parameter to from 'unsigned' to 'int' to avoid bare use of 'unsigned', changing it to 'int' makes goodix_i2c_write()' prototype consistent with goodix_i2c_read(). Reviewed-by: Bastien Nocera <hadess@hadess.net> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20210920150643.155872-2-hdegoede@redhat.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-09-11Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input Pull input updates from Dmitry Torokhov: - several device tree bindings for input devices have been converted to yaml - dropped no longer used ixp4xx-beeper and CSR Prima2 PWRC drivers - analog joystick has been converted to use ktime API and no longer warn about low resolution timers - a few driver fixes * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (24 commits) Input: analog - always use ktime functions Input: mms114 - support MMS134S Input: elan_i2c - reduce the resume time for controller in Whitebox Input: edt-ft5x06 - added case for EDT EP0110M09 Input: adc-keys - drop bogus __refdata annotation Input: Fix spelling mistake in Kconfig "useable" -> "usable" Input: Fix spelling mistake in Kconfig "Modul" -> "Module" Input: remove dead CSR Prima2 PWRC driver Input: adp5589-keys - use the right header Input: adp5588-keys - use the right header dt-bindings: input: tsc2005: Convert to YAML schema Input: ep93xx_keypad - prepare clock before using it dt-bindings: input: sun4i-lradc: Add wakeup-source dt-bindings: input: Convert Regulator Haptic binding to a schema dt-bindings: input: Convert Pixcir Touchscreen binding to a schema dt-bindings: input: Convert ChipOne ICN8318 binding to a schema Input: pm8941-pwrkey - fix comma vs semicolon issue dt-bindings: power: reset: qcom-pon: Convert qcom PON binding to yaml dt-bindings: input: pm8941-pwrkey: Convert pm8941 power key binding to yaml dt-bindings: power: reset: Change 'additionalProperties' to true ...
2021-09-09Input: ads7846 - switch to devm initializationDaniel Mack
This simplies the code a lot and fixes some potential resource leaks in the error return paths. Signed-off-by: Daniel Mack <daniel@zonque.org> Link: https://lore.kernel.org/r/20210907200726.2034962-4-daniel@zonque.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-09-09Input: ads7846 - remove custom filter handling functions from pdataDaniel Mack
The functions in the platform data struct to initialize, cleanup and apply custom filters are not in use by any mainline board. Remove support for them to pave the road for more cleanups to come. The enum was moved as it has no users outside of the driver code itself. Signed-off-by: Daniel Mack <daniel@zonque.org> Reviewed-by: Marco Felsch <m.felsch@pengutronix.de> Link: https://lore.kernel.org/r/20210907200726.2034962-3-daniel@zonque.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-09-09Input: ads7846 - add short-hand for spi->dev in probe() functionDaniel Mack
This will make the code a bit more terse. No functional change intended. Signed-off-by: Daniel Mack <daniel@zonque.org> Reviewed-by: Marco Felsch <m.felsch@pengutronix.de> Link: https://lore.kernel.org/r/20210907200726.2034962-2-daniel@zonque.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-09-06Input: mms114 - support MMS134SLinus Walleij
The MMS134S like the MMS136 has an event size of 6 bytes. After this patch, the touchscreen on the Samsung SGH-I407 works fine with PostmarketOS. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20210706235951.189289-1-linus.walleij@linaro.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-09-05Input: raydium_i2c_ts - read device version in bootloader modesimba.hsu
Add support reading device ID when controller is in bootloader mode, which may happen if firmware update has been interrupted. Signed-off-by: simba.hsu <simba.hsu@rad-ic.com> Link: https://lore.kernel.org/r/20210818063644.8654-1-simba.hsu@rad-ic.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-09-05Input: edt-ft5x06 - added case for EDT EP0110M09Oliver Graute
Add Support for EP011M09 Firmware Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com> Reviewed-by: Marco Felsch <m.felsch@pengutronix.de> Link: https://lore.kernel.org/r/20210813062110.13950-1-oliver.graute@kococonnector.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-09-05Merge branch 'next' into for-linusDmitry Torokhov
Prepare input updates for 5.15 merge window.
2021-09-03Input: Fix spelling mistake in Kconfig "Modul" -> "Module"Colin Ian King
There is a spelling mistake in the Kconfig text. Fix it. Signed-off-by: Colin Ian King <colin.king@canonical.com> Link: https://lore.kernel.org/r/20210704095702.37567-1-colin.king@canonical.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-07-18Merge tag 'v5.13' into nextDmitry Torokhov
Sync up with the mainline to get the latest parport API.
2021-07-05Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input Pull input updates from Dmitry Torokhov: - a new driver for SparkFun Qwiic Joystick - pm8941-pwrkey driver now supports PMK8350 - a bunch of assorted driver fixes * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (44 commits) Input: joydev - prevent use of not validated data in JSIOCSBTNMAP ioctl Input: hideep - fix the uninitialized use in hideep_nvm_unlock() Input: trackpoint - use kobj_to_dev() Input: atkbd - use kobj_to_dev() Input: tsc200x-core - use kobj_to_dev() Input: ims-pcu - use kobj_to_dev() Input: cros_ec_keyb - use kobj_to_dev() API dt-bindings: input: touchscreen: st1232: Convert to json-schema Input: i8042 - fix typos in comments Input: add SparkFun Qwiic Joystick driver dt-bindings: Add vendor prefix and bindings for Qwiic Joystick Input: cy8ctmg110_ts - switch to using gpiod API Input: cy8ctmg110_ts - switch to using managed resources Input: cy8ctmg110_ts - use endian helpers when converting data on wire Input: cy8ctmg110_ts - let I2C core configure wake interrupt Input: cy8ctmg110_ts - do not hardcode as wakeup source Input: cy8ctmg110_ts - do not hard code interrupt trigger Input: cy8ctmg110_ts - rely on platform code to supply interrupt Input: resistive-adc-touch - fix uninitialized variable 'press' Input: pm8941-pwrkey - add support for PMK8350 PON_HLOS PMIC peripheral ...
2021-07-04Merge branch 'next' into for-linusDmitry Torokhov
Prepare input updates for 5.14 merge window.
2021-06-19Input: hideep - fix the uninitialized use in hideep_nvm_unlock()Yizhuo Zhai
Inside function hideep_nvm_unlock(), variable "unmask_code" could be uninitialized if hideep_pgm_r_reg() returns error, however, it is used in the later if statement after an "and" operation, which is potentially unsafe. Signed-off-by: Yizhuo <yzhai003@ucr.edu> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2021-06-19Input: tsc200x-core - use kobj_to_dev()YueHaibing
Use kobj_to_dev() instead of container_of() Generated by: scripts/coccinelle/api/kobj_to_dev.cocci Signed-off-by: YueHaibing <yuehaibing@huawei.com> Link: https://lore.kernel.org/r/20210607122451.36708-1-yuehaibing@huawei.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
generated by cgit (git 2.34.1) at 2025-04-29 15:36:02 +0000