| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Conserve IRQs by setting up portdrv IRQs only when there are users
(Jan Kiszka)
- Rework and simplify _OSC negotiation for control of PCIe features
(Joerg Roedel)
- Remove struct pci_dev.driver pointer since it's redundant with the
struct device.driver pointer (Uwe Kleine-König)
Resource management:
- Coalesce contiguous host bridge apertures from _CRS to accommodate
BARs that cover more than one aperture (Kai-Heng Feng)
Sysfs:
- Check CAP_SYS_ADMIN before parsing user input (Krzysztof
Wilczyński)
- Return -EINVAL consistently from "store" functions (Krzysztof
Wilczyński)
- Use sysfs_emit() in endpoint "show" functions to avoid buffer
overruns (Kunihiko Hayashi)
PCIe native device hotplug:
- Ignore Link Down/Up caused by resets during error recovery so
endpoint drivers can remain bound to the device (Lukas Wunner)
Virtualization:
- Avoid bus resets on Atheros QCA6174, where they hang the device
(Ingmar Klein)
- Work around Pericom PI7C9X2G switch packet drop erratum by using
store and forward mode instead of cut-through (Nathan Rossi)
- Avoid trying to enable AtomicOps on VFs; the PF setting applies to
all VFs (Selvin Xavier)
MSI:
- Document that /sys/bus/pci/devices/.../irq contains the legacy INTx
interrupt or the IRQ of the first MSI (not MSI-X) vector (Barry
Song)
VPD:
- Add pci_read_vpd_any() and pci_write_vpd_any() to access anywhere
in the possible VPD space; use these to simplify the cxgb3 driver
(Heiner Kallweit)
Peer-to-peer DMA:
- Add (not subtract) the bus offset when calculating DMA address
(Wang Lu)
ASPM:
- Re-enable LTR at Downstream Ports so they don't report Unsupported
Requests when reset or hot-added devices send LTR messages
(Mingchuang Qiao)
Apple PCIe controller driver:
- Add driver for Apple M1 PCIe controller (Alyssa Rosenzweig, Marc
Zyngier)
Cadence PCIe controller driver:
- Return success when probe succeeds instead of falling into error
path (Li Chen)
HiSilicon Kirin PCIe controller driver:
- Reorganize PHY logic and add support for external PHY drivers
(Mauro Carvalho Chehab)
- Support PERST# GPIOs for HiKey970 external PEX 8606 bridge (Mauro
Carvalho Chehab)
- Add Kirin 970 support (Mauro Carvalho Chehab)
- Make driver removable (Mauro Carvalho Chehab)
Intel VMD host bridge driver:
- If IOMMU supports interrupt remapping, leave VMD MSI-X remapping
enabled (Adrian Huang)
- Number each controller so we can tell them apart in
/proc/interrupts (Chunguang Xu)
- Avoid building on UML because VMD depends on x86 bare metal APIs
(Johannes Berg)
Marvell Aardvark PCIe controller driver:
- Define macros for PCI_EXP_DEVCTL_PAYLOAD_* (Pali Rohár)
- Set Max Payload Size to 512 bytes per Marvell spec (Pali Rohár)
- Downgrade PIO Response Status messages to debug level (Marek Behún)
- Preserve CRS SV (Config Request Retry Software Visibility) bit in
emulated Root Control register (Pali Rohár)
- Fix issue in configuring reference clock (Pali Rohár)
- Don't clear status bits for masked interrupts (Pali Rohár)
- Don't mask unused interrupts (Pali Rohár)
- Avoid code repetition in advk_pcie_rd_conf() (Marek Behún)
- Retry config accesses on CRS response (Pali Rohár)
- Simplify emulated Root Capabilities initialization (Pali Rohár)
- Fix several link training issues (Pali Rohár)
- Fix link-up checking via LTSSM (Pali Rohár)
- Fix reporting of Data Link Layer Link Active (Pali Rohár)
- Fix emulation of W1C bits (Marek Behún)
- Fix MSI domain .alloc() method to return zero on success (Marek
Behún)
- Read entire 16-bit MSI vector in MSI handler, not just low 8 bits
(Marek Behún)
- Clear Root Port I/O Space, Memory Space, and Bus Master Enable bits
at startup; PCI core will set those as necessary (Pali Rohár)
- When operating as a Root Port, set class code to "PCI Bridge"
instead of the default "Mass Storage Controller" (Pali Rohár)
- Add emulation for PCI_BRIDGE_CTL_BUS_RESET since aardvark doesn't
implement this per spec (Pali Rohár)
- Add emulation of option ROM BAR since aardvark doesn't implement
this per spec (Pali Rohár)
MediaTek MT7621 PCIe controller driver:
- Add MediaTek MT7621 PCIe host controller driver and DT binding
(Sergio Paracuellos)
Qualcomm PCIe controller driver:
- Add SC8180x compatible string (Bjorn Andersson)
- Add endpoint controller driver and DT binding (Manivannan
Sadhasivam)
- Restructure to use of_device_get_match_data() (Prasad Malisetty)
- Add SC7280-specific pcie_1_pipe_clk_src handling (Prasad Malisetty)
Renesas R-Car PCIe controller driver:
- Remove unnecessary includes (Geert Uytterhoeven)
Rockchip DesignWare PCIe controller driver:
- Add DT binding (Simon Xue)
Socionext UniPhier Pro5 controller driver:
- Serialize INTx masking/unmasking (Kunihiko Hayashi)
Synopsys DesignWare PCIe controller driver:
- Run dwc .host_init() method before registering MSI interrupt
handler so we can deal with pending interrupts left by bootloader
(Bjorn Andersson)
- Clean up Kconfig dependencies (Andy Shevchenko)
- Export symbols to allow more modular drivers (Luca Ceresoli)
TI DRA7xx PCIe controller driver:
- Allow host and endpoint drivers to be modules (Luca Ceresoli)
- Enable external clock if present (Luca Ceresoli)
TI J721E PCIe driver:
- Disable PHY when probe fails after initializing it (Christophe
JAILLET)
MicroSemi Switchtec management driver:
- Return error to application when command execution fails because an
out-of-band reset has cleared the device BARs, Memory Space Enable,
etc (Kelvin Cao)
- Fix MRPC error status handling issue (Kelvin Cao)
- Mask out other bits when reading of management VEP instance ID
(Kelvin Cao)
- Return EOPNOTSUPP instead of ENOTSUPP from sysfs show functions
(Kelvin Cao)
- Add check of event support (Logan Gunthorpe)
Miscellaneous:
- Remove unused pci_pool wrappers, which have been replaced by
dma_pool (Cai Huoqing)
- Use 'unsigned int' instead of bare 'unsigned' (Krzysztof
Wilczyński)
- Use kstrtobool() directly, sans strtobool() wrapper (Krzysztof
Wilczyński)
- Fix some sscanf(), sprintf() format mismatches (Krzysztof
Wilczyński)
- Update PCI subsystem information in MAINTAINERS (Krzysztof
Wilczyński)
- Correct some misspellings (Krzysztof Wilczyński)"
* tag 'pci-v5.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (137 commits)
PCI: Add ACS quirk for Pericom PI7C9X2G switches
PCI: apple: Configure RID to SID mapper on device addition
iommu/dart: Exclude MSI doorbell from PCIe device IOVA range
PCI: apple: Implement MSI support
PCI: apple: Add INTx and per-port interrupt support
PCI: kirin: Allow removing the driver
PCI: kirin: De-init the dwc driver
PCI: kirin: Disable clkreq during poweroff sequence
PCI: kirin: Move the power-off code to a common routine
PCI: kirin: Add power_off support for Kirin 960 PHY
PCI: kirin: Allow building it as a module
PCI: kirin: Add MODULE_* macros
PCI: kirin: Add Kirin 970 compatible
PCI: kirin: Support PERST# GPIOs for HiKey970 external PEX 8606 bridge
PCI: apple: Set up reference clocks when probing
PCI: apple: Add initial hardware bring-up
PCI: of: Allow matching of an interrupt-map local to a PCI device
of/irq: Allow matching of an interrupt-map local to an interrupt controller
irqdomain: Make of_phandle_args_to_fwspec() generally available
PCI: Do not enable AtomicOps on VFs
...
|
|
The MSI doorbell on Apple HW can be any address in the low 4GB range.
However, the MSI write is matched by the PCIe block before hitting the
iommu. It must thus be excluded from the IOVA range that is assigned to any
PCIe device.
Link: https://lore.kernel.org/r/20210929163847.2807812-9-maz@kernel.org
Tested-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
|
|
'arm/tegra', 'iommu/fixes', 'x86/amd', 'x86/vt-d' and 'core' into next
|
|
DART has an additional global register to control which streams are
isolated. This register is a bit redundant since DART_TCR can already
be used to control isolation and is usually initialized to DART_STREAM_ALL
by the time we get control. Some DARTs (namely the one used for the audio
controller) however have some streams disabled initially. Make sure those
work by initializing DART_STREAMS_ENABLE during reset.
Reported-by: Martin Povišer <povik@protonmail.com>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Hector Martin <marcan@marcan.st>
Link: https://lore.kernel.org/r/20211019162253.45919-1-sven@svenpeter.dev
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Fix following coccicheck warning:
drivers/iommu/apple-dart.c:704:20-27: WARNING opportunity for kmemdup
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Acked-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Link: https://lore.kernel.org/r/20211013063441.29888-1-wanjiabing@vivo.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
sid2groups keeps track of which stream id combinations belong to a
iommu_group to assign those correctly to devices.
When a iommu_group is freed a stale pointer will however remain in
sid2groups. This prevents devices with the same stream id combination
to ever be attached again (see below).
Fix that by creating a shadow copy of the stream id configuration
when a group is allocated for the first time and clear the sid2group
entry when that group is freed.
# echo 1 >/sys/bus/pci/devices/0000\:03\:00.0/remove
pci 0000:03:00.0: Removing from iommu group 1
# echo 1 >/sys/bus/pci/rescan
[...]
pci 0000:03:00.0: BAR 0: assigned [mem 0x6a0000000-0x6a000ffff 64bit pref]
pci 0000:03:00.0: BAR 2: assigned [mem 0x6a0010000-0x6a001ffff 64bit pref]
pci 0000:03:00.0: BAR 6: assigned [mem 0x6c0100000-0x6c01007ff pref]
tg3 0000:03:00.0: Failed to add to iommu group 1: -2
[...]
Fixes: 46d1fb072e76b161 ("iommu/dart: Add DART iommu driver")
Reported-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Tested-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210924134502.15589-1-sven@svenpeter.dev
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
apple_dart_tlb_flush_{all,walk} expect to get a struct apple_dart_domain
but instead get a struct iommu_domain right now. This breaks those two
functions and can lead to kernel panics like the one below.
DART can only invalidate the entire TLB and apple_dart_iotlb_sync will
already flush everything. There's no need to do that again inside those
two functions. Let's just drop them.
pci 0000:03:00.0: Removing from iommu group 1
Unable to handle kernel paging request at virtual address 0000000100000023
[...]
Call trace:
_raw_spin_lock_irqsave+0x54/0xbc
apple_dart_hw_stream_command.constprop.0+0x2c/0x130
apple_dart_tlb_flush_all+0x48/0x90
free_io_pgtable_ops+0x40/0x70
apple_dart_domain_free+0x2c/0x44
iommu_group_release+0x68/0xac
kobject_cleanup+0x4c/0x1fc
kobject_cleanup+0x14c/0x1fc
kobject_put+0x64/0x84
iommu_group_remove_device+0x110/0x180
iommu_release_device+0x50/0xa0
[...]
Fixes: 46d1fb072e76b161 ("iommu/dart: Add DART iommu driver")
Reported-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Acked-by: Marc Zyngier <maz@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210921153934.35647-1-sven@svenpeter.dev
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The addition of the DART driver crossed over with moving IOVA cookie
management into core code; clean up the now-unnecessary remnants here.
Acked-by: Sven Peter <sven@svenpeter.dev>
Tested-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/edb72b4965baa8999dd70b8294785d6deebd4183.1631531973.git.robin.murphy@arm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Apple's new SoCs use iommus for almost all peripherals. These Device
Address Resolution Tables must be setup before these peripherals can
act as DMA masters.
Tested-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Link: https://lore.kernel.org/r/20210803121651.61594-4-sven@svenpeter.dev
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
