| Age | Commit message (Collapse) | Author |
|---|
|
Expose hw_control status via sysfs for the netdev trigger to give
userspace better understanding of the current state of the trigger and
the LED.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Acked-by: Lee Jones <lee@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add additional modes for specific link duplex. Use ethtool APIs to get the
current link duplex and enable the LED accordingly. Under netdev event
handler the rtnl lock is already held and is not needed to be set to
access ethtool APIs.
This is especially useful for PHY and Switch that supports LEDs hw
control for specific link duplex.
Add additional modes:
- half_duplex: Turn on LED when link is half duplex
- full_duplex: Turn on LED when link is full duplex
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Lee Jones <lee@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add additional modes for specific link speed. Use ethtool APIs to get the
current link speed and enable the LED accordingly. Under netdev event
handler the rtnl lock is already held and is not needed to be set to
access ethtool APIs.
This is especially useful for PHY and Switch that supports LEDs hw
control for specific link speed. (example scenario a PHY that have 2 LED
connected one green and one orange where the green is turned on with
1000mbps speed and orange is turned on with 10mpbs speed)
On mode set from sysfs we check if we have enabled split link speed mode
and reject enabling generic link mode to prevent wrong and redundant
configuration.
Rework logic on the set baseline state to support these new modes to
select if we need to turn on or off the LED.
Add additional modes:
- link_10: Turn on LED when link speed is 10mbps
- link_100: Turn on LED when link speed is 100mbps
- link_1000: Turn on LED when link speed is 1000mbps
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Lee Jones <lee@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The qca8k_cled_hw_control_get() function which implements ->hw_control_get
sets the appropriate bits but does not clear them. This leads to an
uninitialized variable bug. Fix this by setting mode to zero at the
start.
Fixes: e0256648c831 ("net: dsa: qca8k: implement hw_control ops")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Lee Jones <lee@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
net/sched/sch_taprio.c
d636fc5dd692 ("net: sched: add rcu annotations around qdisc->qdisc_sleeping")
dced11ef84fb ("net/sched: taprio: don't overwrite "sch" variable in taprio_dump_class_stats()")
net/ipv4/sysctl_net_ipv4.c
e209fee4118f ("net/ipv4: ping_group_range: allow GID from 2147483648 to 4294967294")
ccce324dabfe ("tcp: make the first N SYN RTO backoffs linear")
https://lore.kernel.org/all/20230605100816.08d41a7b@canb.auug.org.au/
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The introduction of high resolution PWM support changed the order of the
operations in the calculation of min and max period. The result in both
divisions is in most cases a truncation to 0, which limits the period to
the range of [0, 0].
Both numerators (and denominators) are within 64 bits, so the whole
expression can be put directly into the div64_u64, instead of doing it
partially.
Fixes: b00d2ed37617 ("leds: rgb: leds-qcom-lpg: Add support for high resolution PWM")
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Acked-by: Lee Jones <lee@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Link: https://lore.kernel.org/r/20230515162604.649203-1-quic_bjorande@quicinc.com
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Expose netdev trigger modes to make them accessible by LED driver that
will support netdev trigger for hw control.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On netdev trigger activation, hw control may be already active by
default. If this is the case and a device is actually provided by
hw_control_get_device(), init the already active mode and set the
bool to hw_control bool to true to reflect the already set mode in the
trigger_data.
Co-developed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The netdev which the LED should blink for is configurable in
/sys/class/led/foo/device_name. Ensure when offloading that the
configured netdev is the same as the netdev the LED is associated
with. If it is not, only perform software blinking.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for LED hw control for the netdev trigger.
The trigger on calling set_baseline_state to configure a new mode, will
do various check to verify if hw control can be used for the requested
mode in can_hw_control() function.
It will first check if the LED driver supports hw control for the netdev
trigger, then will use hw_control_is_supported() and finally will call
hw_control_set() to apply the requested mode.
To use such mode, interval MUST be set to the default value and net_dev
MUST be set. If one of these 2 value are not valid, hw control will
never be used and normal software fallback is used.
The default interval value is moved to a define to make sure they are
always synced.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reject interval store with hw_control enabled. It's are currently not
supported and MUST be set to the default value with hw control enabled.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add basic check for hw control support. Check if the required API are
defined and check if the defined trigger supported in hw control for the
LED driver match netdev.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce function to check if the requested mode can use hw control in
preparation for hw control support. Currently everything is handled in
software so can_hw_control will always return false.
Add knob with the new value hw_control in trigger_data struct to
set hw control possible. Useful for future implementation to implement
in set_baseline_state() the required function to set the requested mode
using LEDs hw control ops and in other function to reject set if hw
control is currently active.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the code into a helper, ready for it to be called at
other times. No intended behaviour change.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some LEDs may require to sleep while doing some operation like setting
brightness and other cleanup.
For this reason, using a spinlock will cause a sleep under spinlock
warning.
It should be safe to convert this to a sleepable lock since:
- sysfs read/write can sleep
- netdev_trig_work is a work queue and can sleep
- netdev _trig_notify can sleep
The spinlock was used when brightness didn't support sleeping, but this
changed and now it supported with brightness_set_blocking().
Convert to mutex lock to permit sleeping using brightness_set_blocking().
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230419210743.3594-6-ansuelsmth@gmail.com
|
|
Convert link tx and rx device attr to a common macro to reduce common
code and in preparation for additional attr.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230419210743.3594-5-ansuelsmth@gmail.com
|
|
Rename NETDEV trigger enum modes to a more symbolic name and add a
namespace to them.
Also add __TRIGGER_NETDEV_MAX to identify the max modes of the netdev
trigger.
This is a cleanup to drop the define and no behaviour change are
intended.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230419210743.3594-4-ansuelsmth@gmail.com
|
|
Putting NETDEV_LED_MODE_LINKUP in the same list of the netdev trigger
modes is wrong as it's used to set the link state of the device and not
to set a blink mode as it's done by NETDEV_LED_LINK, NETDEV_LED_TX and
NETDEV_LED_RX. It's also wrong to put this state in the same bitmap of the
netdev trigger mode and should be external to it.
Drop NETDEV_LED_MODE_LINKUP from mode list and convert to a simple bool
that will be true or false based on the carrier link. No functional
change intended.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230419210743.3594-3-ansuelsmth@gmail.com
|
|
Dev can be renamed also while up for supported device. We currently
wrongly clear the NETDEV_LED_MODE_LINKUP flag on NETDEV_CHANGENAME
event.
Fix this by rechecking if the carrier is ok on NETDEV_CHANGENAME and
correctly set the NETDEV_LED_MODE_LINKUP bit.
Fixes: 5f820ed52371 ("leds: trigger: netdev: fix handling on interface rename")
Cc: stable@vger.kernel.org # v5.5+
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230419210743.3594-2-ansuelsmth@gmail.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds
Pull LED updates from Lee Jones:
"New Drivers:
- Add support for MediaTek MT6370 LED Indicator
- Add support for MediaTek MT6370 Flashlight
- Add support for QCOM PMIC Flash
- Add support for Rohm BD2606MVV Charge Pump LED
New Device Support:
- Add support for PMK8550 PWM to QCOM LPG
New Functionality:
- Add support for high resolution PWM to QCOM LPG
Fix-ups:
- Kconfig 'depends' and 'select' dependency changes
- Remove unused / irrelevant includes
- Remove unnecessary checks (already performed further into the call stack)
- Trivial: Fix commentary, simplify error messages
- Rid 'defined but not used' warnings
- Provide documentation
- Explicitly provide include files
Bug Fixes:
- Mark GPIO LED as BROKEN
- Fix Kconfig entries
- Fix various Smatch staticify reports
- Fix error handling (or a lack there of)"
* tag 'leds-next-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (30 commits)
leds: bd2606mvv: Driver for the Rohm 6 Channel i2c LED driver
dt-bindings: leds: Add ROHM BD2606MVV LED
docs: leds: ledtrig-oneshot: Fix spelling mistake
leds: pwm-multicolor: Simplify an error message
dt-bindings: leds: Convert PCA9532 to dtschema
leds: rgb: leds-qcom-lpg: Add support for PMK8550 PWM
leds: rgb: leds-qcom-lpg: Add support for high resolution PWM
dt-bindings: leds-qcom-lpg: Add qcom,pmk8550-pwm compatible string
leds: tca6507: Fix error handling of using fwnode_property_read_string
leds: flash: Set variables mvflash_{3,4}ch_regs storage-class-specifier to static
leds: rgb: mt6370: Correct config name to select in LEDS_MT6370_RGB
MAINTAINERS: Add entry for LED devices documentation
Documentation: leds: MT6370: Use bullet lists for timing variables
Documentation: leds: mt6370: Properly wrap hw_pattern chart
Documentation: leds: Add MT6370 doc to the toctree
leds: rgb: mt6370: Fix implicit declaration for FIELD_GET
docs: leds: Add MT6370 RGB LED pattern document
leds: flash: mt6370: Add MediaTek MT6370 flashlight support
leds: rgb: mt6370: Add MediaTek MT6370 current sink type LED Indicator support
dt-bindings: leds: spmi-flash-led: Add pm6150l compatible
...
|
|
The device provides 6 channels which can be individually
turned off and on but groups of two channels share a common brightness
register.
Limitation: The GPIO to enable the device is not used yet.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230419111806.1100437-3-andreas@kemnade.info
|
|
dev_err_probe() already display the error code. There is no need to
duplicate it explicitly in the error message.
While at it, add a missing \n at the end of the message.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/07d35e221faaa380fd11cd4597e42354c8eb350c.1681576017.git.christophe.jaillet@wanadoo.fr
|
|
Add support for pmk8550 compatible and lpg_data.
Signed-off-by: Anjelique Melendez <quic_amelende@quicinc.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230407223849.17623-4-quic_amelende@quicinc.com
|
|
Certain PMICs like PMK8550 have a high resolution PWM module which can
support from 8-bit to 15-bit PWM. Add support for it.
Signed-off-by: Anjelique Melendez <quic_amelende@quicinc.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230407223849.17623-3-quic_amelende@quicinc.com
|
|
Commit 96f524105b9c ("leds: tca6507: use fwnode API instead of OF")
changed to fwnode API but did not take into account that a missing property
"linux,default-trigger" now seems to return an error and as a side effect
sets value to -1. This seems to be different from of_get_property() which
always returned NULL in any case of error.
Neglecting this side-effect leads to
[ 11.201965] Unable to handle kernel paging request at virtual address ffffffff when read
in the strcmp() of led_trigger_set_default() if there is no led-trigger
defined in the DTS.
I don't know if this was recently introduced somewhere in the fwnode lib
or if the effect was missed in initial testing. Anyways it seems to be a
bug to ignore the error return value of an optional value here in the
driver.
Fixes: 96f524105b9c ("leds: tca6507: use fwnode API instead of OF")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/cbae7617db83113de726fcc423a805ebaa1bfca6.1680433978.git.hns@goldelico.com
|
|
static
Smatch reports:
drivers/leds/flash/leds-qcom-flash.c:103:18: warning:
symbol 'mvflash_3ch_regs' was not declared. Should it be static?
drivers/leds/flash/leds-qcom-flash.c:115:18: warning:
symbol 'mvflash_4ch_regs' was not declared. Should it be static?
These variables are only used locally, so it should be static.
Signed-off-by: Tom Rix <trix@redhat.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230317191341.1670660-1-trix@redhat.com
|
|
Commit 55a8a5c16eb3 ("leds: rgb: mt6370: Add MediaTek MT6370 current sink
type LED Indicator support") introduces the config LEDS_MT6370_RGB, which
selects the non-existing config LINEAR_RANGE. As the driver includes
linux/linear_range.h, it is a safe guess that the config actually intends
to select LINEAR_RANGES, which provides the library implementation for the
function prototypes defined in the linear_range header file.
Correct this naming confusion in the LEDS_MT6370_RGB config definition.
Fixes: 55a8a5c16eb3 ("leds: rgb: mt6370: Add MediaTek MT6370 current sink type LED Indicator support")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230323105410.10396-1-lukas.bulwahn@gmail.com
|
|
0-DAY CI Kernel Test Service reported the implicit declaration error below:
drivers/leds/rgb/leds-mt6370-rgb.c: In function'mt6370_check_vendor_info':
>> drivers/leds/rgb/leds-mt6370-rgb.c:889:15: error: implicit declaration
of function 'FIELD_GET' [-Werror=implicit-function-declaration]
889 | vid = FIELD_GET(MT6370_VENDOR_ID_MASK, devinfo);
|
Add the missing header 'bitfield.h' to fix it.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/oe-kbuild-all/202303171729.CcgyFx17-lkp@intel.com/
Fixes: 55a8a5c16eb3 ("leds: rgb: mt6370: Add MediaTek MT6370 current sink type LED Indicator support")
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/1679067760-19098-1-git-send-email-cy_huang@richtek.com
|
|
The MediaTek MT6370 is a highly-integrated smart power management IC,
which includes a single cell Li-Ion/Li-Polymer switching battery
charger, a USB Type-C & Power Delivery (PD) controller, dual Flash
LED current sources, a RGB LED driver, a backlight WLED driver,
a display bias driver and a general LDO for portable devices.
Add support for the MT6370 Flash LED driver. Flash LED in MT6370
has 2 channels and support torch/strobe mode.
Co-developed-by: Alice Chen <alice_chen@richtek.com>
Signed-off-by: Alice Chen <alice_chen@richtek.com>
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Signed-off-by: ChiaEn Wu <chiaen_wu@richtek.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/52480420a160e5a4c71715fbbf105e684a16e7c2.1678430444.git.chiaen_wu@richtek.com
|
|
The MediaTek MT6370 is a highly-integrated smart power management IC,
which includes a single cell Li-Ion/Li-Polymer switching battery
charger, a USB Type-C & Power Delivery (PD) controller, dual
Flash LED current sources, a RGB LED driver, a backlight WLED driver,
a display bias driver and a general LDO for portable devices.
Add support for the MediaTek MT6370 Current Sink Type LED Indicator
driver. It can control four channels current-sink RGB LEDs with 3 modes:
constant current, PWM, and breath mode.
Co-developed-by: Alice Chen <alice_chen@richtek.com>
Signed-off-by: Alice Chen <alice_chen@richtek.com>
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Signed-off-by: ChiaEn Wu <chiaen_wu@richtek.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/1df93a583c3f508a7158b83b95857e9bce235e1b.1678430444.git.chiaen_wu@richtek.com
|
|
The module pointer in class_create() never actually did anything, and it
shouldn't have been requred to be set as a parameter even if it did
something. So just remove it and fix up all callers of the function in
the kernel tree at the same time.
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20230313181843.1207845-4-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add initial driver to support flash LED module found in Qualcomm
Technologies, Inc. PMICs. The flash module can have 3 or 4 channels
and each channel can be controlled indepedently and support full scale
current up to 1.5 A. It also supports connecting two channels together
to supply one LED component with full scale current up to 2 A. In that
case, the current will be split on each channel symmetrically and the
channels will be enabled and disabled at the same time.
Signed-off-by: Fenglin Wu <quic_fenglinw@quicinc.com>
Tested-by: Luca Weiss <luca.weiss@fairphone.com> # sm7225-fairphone-fp4 + pm6150l
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230303095023.538917-2-quic_fenglinw@quicinc.com
|
|
The GPIO LED trigger exposes a userspace ABI where a user
can echo a GPIO number from the global GPIO numberspace into
a file that will trigger a certain LED when active.
This is problematic because the global GPIO numberspace is
inherently instable. The trigger came about at a time when
systems had one GPIO controller that defined hard-wired
GPIOs numbered 0..N and this number space was stable.
We have since moved to dynamic allocation of GPIO numbers
and there is no real guarantee that a GPIO number will stay
consistent even across a reboot: consider a USB attached
GPIO controller for example. Or two. Or the effect of
probe order after adding -EPROBE_DEFER to the kernel.
The trigger was added to support keypad LEDs on the Nokia
n810 from the GPIO event when a user slides up/down the
keypad. This is arch/arm/boot/dts/omap2420-n810.dts.
A userspace script is needed to activate the trigger.
This will be broken unless the script was updated recently
since the OMAP GPIO controller now uses dynamic GPIO
number allocations.
I want to know that this trigger has active users that
cannot live without it if we are to continue to support it.
Option if this is really needed: I can develop a new trigger
that can associate GPIOs with LEDs as triggers using device
tree, which should also remove the use of userspace custom
scripts to achieve this and be much more trustworthy, if
someone with the Nokia n810 or a device with a similar need
is willing to test it.
Suggested-by Pavel Machek <pavel@ucw.cz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230314210059.419159-1-linus.walleij@linaro.org
|
|
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/leds/leds-tlc591xx.c:138:34: error: ‘of_tlc591xx_leds_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230311111717.252019-1-krzysztof.kozlowski@linaro.org
|
|
gpiod_*() API check already for the NULL, no need
to repeat that in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230215170403.84449-2-andriy.shevchenko@linux.intel.com
|
|
of_gpio.h provides a single function, which is not used in this driver.
Remove unused header.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230215170403.84449-1-andriy.shevchenko@linux.intel.com
|
|
REGMAP is a hidden (not user visible) symbol. Users cannot set it
directly thru "make *config", so drivers should select it instead of
depending on it if they need it.
Consistently using "select" or "depends on" can also help reduce
Kconfig circular dependency issues.
Therefore, change the use of "depends on REGMAP" to "select REGMAP".
Fixes: 3fce8e1eb994 ("leds: TI LMU: Add common code for TI LMU devices")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230226053953.4681-5-rdunlap@infradead.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds
Pull LED updates from Lee Jones:
"Removed Drivers:
- HTC ASIC3 LED
New Functionality:
- Provide generic led_get() which can be used by both DT and !DT
platforms
Fix-ups:
- Convert a bunch of I2C subsystem users to the new probing API
- Explicitly provide missing include files
- Make use of led_init_default_state_get() and rid the custom
variants
- Use simplified fwnode_device_is_compatible() API
- Provide some Device Tree additions / adaptions
- Fix some trivial spelling issues
Bug Fixes:
- Prevent device refcount leak during led_put() and of_led_get()
- Clear previous data from temporary led_pwm structure before
processing next child
- Fix Clang's warning about incompatible function types when using
devm_add_action*()"
* tag 'leds-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (41 commits)
leds: Remove ide-disk trigger
dt-bindings: leds: Add disk write/read and usb-host/usb-gadget
Documentation: leds: Correct spelling
dt-bindings: leds: Document Bluetooth and WLAN triggers
leds: Remove asic3 driver
leds: simatic-ipc-leds-gpio: Make sure we have the GPIO providing driver
leds: tca6507: Convert to use fwnode_device_is_compatible()
leds: syscon: Get rid of custom led_init_default_state_get()
leds: pm8058: Get rid of custom led_init_default_state_get()
leds: pca955x: Get rid of custom led_init_default_state_get()
leds: mt6360: Get rid of custom led_init_default_state_get()
leds: mt6323: Get rid of custom led_init_default_state_get()
leds: bcm6358: Get rid of custom led_init_default_state_get()
leds: bcm6328: Get rid of custom led_init_default_state_get()
leds: an30259a: Get rid of custom led_init_default_state_get()
leds: Move led_init_default_state_get() to the global header
leds: Add missing includes and forward declarations in leds.h
leds: is31fl319x: Wrap mutex_destroy() for devm_add_action_or_rest()
leds: turris-omnia: Convert to i2c's .probe_new()
leds: tlc591xx: Convert to i2c's .probe_new()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver updates from Hans de Goede:
- AMD PMC: Improvements to aid s2idle debugging
- Dell WMI-DDV: hwmon support
- INT3472 camera sensor power-management: Improve privacy LED support
- Intel VSEC: Base TPMI (Topology Aware Register and PM Capsule
Interface) support
- Mellanox: SN5600 and Nvidia L1 switch support
- Microsoft Surface Support: Various cleanups + code improvements
- tools/intel-speed-select: Various improvements
- Miscellaneous other cleanups / fixes
* tag 'platform-drivers-x86-v6.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (80 commits)
platform/x86: nvidia-wmi-ec-backlight: Add force module parameter
platform/x86/amd/pmf: Add depends on CONFIG_POWER_SUPPLY
platform/x86: dell-ddv: Prefer asynchronous probing
platform/x86: dell-ddv: Add hwmon support
Documentation/ABI: Add new attribute for mlxreg-io sysfs interfaces
platform: mellanox: mlx-platform: Move bus shift assignment out of the loop
platform: mellanox: mlx-platform: Add mux selection register to regmap
platform_data/mlxreg: Add field with mapped resource address
platform/mellanox: mlxreg-hotplug: Allow more flexible hotplug events configuration
platform: mellanox: Extend all systems with I2C notification callback
platform: mellanox: Split logic in init and exit flow
platform: mellanox: Split initialization procedure
platform: mellanox: Introduce support of new Nvidia L1 switch
platform: mellanox: Introduce support for next-generation 800GB/s switch
platform: mellanox: Cosmetic changes - rename to more common name
platform: mellanox: Change "reset_pwr_converter_fail" attribute
platform: mellanox: Introduce support for rack manager switch
MAINTAINERS: dell-wmi-sysman: drop Divya Bharathi
x86/platform/uv: Make kobj_type structure constant
platform/x86: think-lmi: Make kobj_type structure constant
...
|
|
No user of ide-disk remains, so remove this deprecated trigger.
Only a few platforms used this and were fixed in 2016.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230131140304.626779-2-clabbe@baylibre.com
|
|
Since ASIC3 MFD driver is removed, the LED support is also
obsolete.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230105134622.254560-25-arnd@kernel.org
|
|
If we register a "leds-gpio" platform device for GPIO pins that do not
exist we get a -EPROBE_DEFER and the probe will be tried again later.
If there is no driver to provide that pin we will poll forever and also
create a lot of log messages.
So check if that GPIO driver is configured, if so it will come up
eventually. If not, we exit our probe function early and do not even
bother registering the "leds-gpio". This method was chosen over "Kconfig
depends" since this way we can add support for more devices and GPIO
backends more easily without "depends":ing on all GPIO backends.
Fixes: a6c80bec3c93 ("leds: simatic-ipc-leds-gpio: Add GPIO version of Siemens driver")
Signed-off-by: Henning Schild <henning.schild@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221007153323.1326-1-henning.schild@siemens.com
|
|
Replace open coded fwnode_device_is_compatible() in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230119175150.77250-1-andriy.shevchenko@linux.intel.com
|
|
LED core provides a helper to parse default state from firmware node.
Use it instead of custom implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230103131256.33894-11-andriy.shevchenko@linux.intel.com
|
|
LED core provides a helper to parse default state from firmware node.
Use it instead of custom implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230103131256.33894-10-andriy.shevchenko@linux.intel.com
|
|
LED core provides a helper to parse default state from firmware node.
Use it instead of custom implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230103131256.33894-9-andriy.shevchenko@linux.intel.com
|
|
LED core provides a helper to parse default state from firmware node.
Use it instead of custom implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230103131256.33894-8-andriy.shevchenko@linux.intel.com
|
|
LED core provides a helper to parse default state from firmware node.
Use it instead of custom implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230103131256.33894-7-andriy.shevchenko@linux.intel.com
|
|
LED core provides a helper to parse default state from firmware node.
Use it instead of custom implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230103131256.33894-6-andriy.shevchenko@linux.intel.com
|
|
LED core provides a helper to parse default state from firmware node.
Use it instead of custom implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230103131256.33894-5-andriy.shevchenko@linux.intel.com
|
