| Age | Commit message (Collapse) | Author |
|---|
|
I noticed that repeatedly running 'cec-ctl --playback' would occasionally
select 'Playback Device 2' instead of 'Playback Device 1', even though there
were no other Playback devices in the HDMI topology. This happened both with
'real' hardware and with the vivid CEC emulation, suggesting that this was an
issue in the core code that claims a logical address.
What 'cec-ctl --playback' does is to first clear all existing logical addresses,
and immediately after that configure the new desired device type.
The core code will poll the logical addresses trying to find a free address.
When found it will issue a few standard messages as per the CEC spec and return.
Those messages are queued up and will be transmitted asynchronously.
What happens is that if you run two 'cec-ctl --playback' commands in quick
succession, there is still a message of the first cec-ctl command being transmitted
when you reconfigure the adapter again in the second cec-ctl command.
When the logical addresses are cleared, then all information about outstanding
transmits inside the CEC core is also cleared, and the core is no longer aware
that there is still a transmit in flight.
When the hardware finishes the transmit it calls transmit_done and the CEC core
thinks it is actually in response of a POLL messages that is trying to find a
free logical address. The result of all this is that the core thinks that the
logical address for Playback Device 1 is in use, when it is really an earlier
transmit that ended.
The main transmit thread looks at adap->transmitting to check if a transmit
is in progress, but that is set to NULL when the adapter is unconfigured.
adap->transmitting represents the view of userspace, not that of the hardware.
So when unconfiguring the adapter the message is marked aborted from the point
of view of userspace, but seen from the PoV of the hardware it is still ongoing.
So introduce a new bool transmit_in_progress that represents the hardware state
and use that instead of adap->transmitting. Now the CEC core waits until the
hardware finishes the transmit before starting a new transmit.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: <stable@vger.kernel.org> # for v4.18 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The CEC specification requires that the Vendor ID (if any) is reported
after a logical address was claimed.
This was never done, so add support for this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The "transmit queue full" message doesn't warrant debug level 1 since
it is already clear from the error code what's going on.
Bump to level 2.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
During the configuration phase of a CEC adapter it is trying to claim a
free logical address by polling.
However, the code doesn't check if there were errors other than OK or NACK,
those are just treated as if the poll was NACKed.
Instead check for such errors and retry the poll. And if the problem persists
then don't claim this LA since there is something weird going on.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
If the wait for completion was interrupted, then make sure to cancel
any delayed work.
This can only happen if a transmit is waiting for a reply, and you press
Ctrl-C or reboot/poweroff or something like that which interrupts the
thread waiting for the reply and then proceeds to delete the CEC message.
Since the delayed work wasn't canceled, once it would trigger it referred
to stale data and resulted in a kernel oops.
Fixes: 7ec2b3b941a6 ("cec: add new tx/rx status bits to detect aborts/timeouts")
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.18 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The calculation of the Signal Free Time in the framework was not
correct. If a message was received, then the next transmit should be
considered a New Initiator and use a shorter SFT value.
This was not done with the result that if both sides where continually
sending messages, they both could use the same SFT value and one side
could deny the other side access to the bus.
Note that this fix does not take the corner case into account where
a receive is in progress when you call adap_transmit.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.18 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
If the HDMI cable is disconnected or the CEC adapter is manually
unconfigured, then all pending transmits and wait-for-replies are
aborted. Signal this with new status bits (CEC_RX/TX_STATUS_ABORTED).
If due to (usually) a driver bug a transmit never ends (i.e. the
transmit_done was never called by the driver), then when this times
out the message is marked with CEC_TX_STATUS_TIMEOUT.
This should not happen and is an indication of a driver bug.
Without a separate status bit for this it was impossible to detect
this from userspace.
The 'transmit timed out' kernel message is now a warning, so this
should be more prominent in the kernel log as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.18 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Move cec_get_edid_phys_addr() to cec-adap.c. It's not worth keeping
a separate source for this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.17 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Add support for the new 5V CEC events
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
When a message was canceled it could return tx_status with
both OK and MAX_RETRIES set, which is illegal.
If a canceled message was waiting for a reply, then rx_status
wasn't updated, so set that as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
It turns out that the struct cec_fh event buffer size of 64 events
(64 for CEC_EVENT_PIN_CEC_LOW and 64 for _HIGH) is too small. It's
about 160 ms worth of events and if the Raspberry Pi is busy, then it
might take too long for the application to be scheduled so that it can
drain the pending events. Increase these buffers to 800 events which
is at least 2 seconds worth of events.
There is also a FIFO in between the interrupt and the cec-pin thread.
The thread passes the events on to the CEC core. It is important that
should this FIFO fill up the cec core will be informed that events
have been lost so this can be communicated to the user by setting
CEC_EVENT_FL_DROPPED_EVENTS.
It is very hard to debug CEC problems if events were lost without
informing the user of that fact.
If events were dropped due to the FIFO filling up, then the debugfs
status file will let you know how many events were dropped.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
cec_transmit_msg_fh() first checked the message for errors, and only
after the message was found to be valid did it log the message contents.
However, that makes it hard to associate an error in the kernel log with
the message since the message contents was never logged in that case.
So swap the order: first log the message (once some very basic checks
are done), and only after that check for errors.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Replace the old license information with the corresponding SPDX
license.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
CEC autorepeat is different than other protocols. Autorepeat is triggered
by the first repeated user control pressed CEC message, rather than a
fixed REP_DELAY.
This change also does away with the KEY_UP event directly after the first
KEY_DOWN event, which was used to stop autorepeat from starting.
See commit a9a249a2c997 ("media: cec: fix remote control passthrough")
for the original change.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Some devices can monitor the CEC pin using an interrupt, but you
only want to enable the interrupt if you actually switch to pin
monitoring mode.
So add a new op that is called when pin monitoring needs to be
switched on or off.
Also fix a small bug where the initial CEC pin event was sent
again when calling S_MODE twice with the same CEC_MODE_MONITOR_PIN
mode.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
It's not clear if the transmit status that is printed when debugging
is enabled is hex or decimal. Add 0x prefix to make this explicit.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Linux 4.14-rc2
* tag 'v4.14-rc2': (12066 commits)
Linux 4.14-rc2
tpm: ibmvtpm: simplify crq initialization and document crq format
tpm: replace msleep() with usleep_range() in TPM 1.2/2.0 generic drivers
Documentation: tpm: add powered-while-suspended binding documentation
tpm: tpm_crb: constify acpi_device_id.
tpm: vtpm: constify vio_device_id
security: fix description of values returned by cap_inode_need_killpriv
x86/asm: Fix inline asm call constraints for Clang
objtool: Handle another GCC stack pointer adjustment bug
inet: fix improper empty comparison
net: use inet6_rcv_saddr to compare sockets
net: set tb->fast_sk_family
net: orphan frags on stand-alone ptype in dev_queue_xmit_nit
MAINTAINERS: update git tree locations for ieee802154 subsystem
SMB3: Don't ignore O_SYNC/O_DSYNC and O_DIRECT flags
SMB3: handle new statx fields
arch: remove unused *_segments() macros/functions
parisc: Unbreak bootloader due to gcc-7 optimizations
parisc: Reintroduce option to gzip-compress the kernel
apparmor: fix apparmorfs DAC access permissions
...
|
|
Add support for two new low-level events: PIN_HPD_LOW and PIN_HPD_HIGH.
This is specifically meant for use with the upcoming cec-gpio driver
and makes it possible to trace when the HPD pin changes. Some HDMI
sinks do strange things with the HPD and this makes it easy to debug
this.
Note that this also moves the initialization of a devnode mutex and
list to the allocate_adapter function: if the HPD is high, then as
soon as the HPD interrupt is created an interrupt occurs and
cec_queue_pin_hpd_event() is called which requires that the devnode
mutex and list are initialized.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Running CEC 1.4 compliance test we get the following error on test
11.1.6.2: "ERROR: The DUT did not broadcast a
<Report Physical Address> message to the unregistered device."
Fix this by letting GIVE_PHYSICAL_ADDR message respond to unregistered
device. Also, GIVE_DEVICE_VENDOR_ID and GIVE_FEATURES fall in the
same category so, respond also to these messages.
With this fix we pass CEC 1.4 official compliance.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.10 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
gcc-4.4.4 has issues with initialization of anonymous unions:
drivers/media/cec/cec-adap.c: In function 'cec_queue_msg_fh':
drivers/media/cec/cec-adap.c:184: error: unknown field 'lost_msgs' specified in initializer
work around this.
Fixes: 6b2bbb08747a5 ("media: cec: rework the cec event handling")
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When the adapter is removed the cec_delete_adapter() call attempts
to set the physical address to INVALID by calling __cec_s_phys_addr()
and so disabling the adapter.
However, __cec_s_phys_addr checks if the device node was unregistered
and just returns in that case.
This means that the adap_enable callback is never called with 'false'
to disable the CEC adapter. Most drivers don't care, but some need
to do cleanup here.
Change the test so the adapter is correctly disabled, even when the
device node is unregistered.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
RC_TYPE is confusing and it's just the protocol. So rename it.
Suggested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The 'Press and Hold' operation was not correctly implemented, in
particular the requirement that the repeat doesn't start until
the second identical keypress arrives. The REP_DELAY value also
had to be adjusted (see the comment in the code) to achieve the
desired behavior.
The 'enabled_protocols' field was also never set, fix that too. Since
CEC is a fixed protocol the driver has to set this field.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The CEC_EVENT_PIN_LOW/HIGH defines and the cec_queue_pin_event() function
did not specify that these were about CEC pin events.
Since in the future there will also be HPD pin events it is wise to rename
the event defines and function to CEC_EVENT_PIN_CEC_LOW/HIGH and
cec_queue_pin_cec_event() now before these become part of the ABI.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Linux 4.13-rc4
* tag 'v4.13-rc4': (863 commits)
Linux 4.13-rc4
Fix compat_sys_sigpending breakage
ext4: fix copy paste error in ext4_swap_extents()
ext4: fix overflow caused by missing cast in ext4_resize_fs()
ext4, project: expand inode extra size if possible
ext4: cleanup ext4_expand_extra_isize_ea()
ext4: restructure ext4_expand_extra_isize
ext4: fix forgetten xattr lock protection in ext4_expand_extra_isize
ext4: make xattr inode reads faster
ext4: inplace xattr block update fails to deduplicate blocks
ext4: remove unused mode parameter
ext4: fix warning about stack corruption
ext4: fix dir_nlink behaviour
ext4: silence array overflow warning
ext4: fix SEEK_HOLE/SEEK_DATA for blocksize < pagesize
platform/x86: intel-vbtn: match power button on press rather than release
ext4: release discard bio after sending discard commands
sparc64: Fix exception handling in UltraSPARC-III memcpy.
arm64: avoid overflow in VA_START and PAGE_OFFSET
arm64: Fix potential race with hardware DBM in ptep_set_access_flags()
...
|
|
The switch in cec_transmit_attempt_done() should ignore the
CEC_TX_STATUS_MAX_RETRIES status bit.
Calling this function with e.g. CEC_TX_STATUS_NACK | CEC_TX_STATUS_MAX_RETRIES
is perfectly legal and should not trigger the WARN(1).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Some hardware does more than one attempt. So when it calls
cec_transmit_done when an error occurred it will e.g. use an error count
of 2 instead of 1.
The framework always assumed a single attempt, but now it is smarter
and will sum the counters to detect how many attempts were made.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Add support for the new MONITOR_PIN mode.
Add the cec_pin_event function that the CEC pin code will call to queue pin
change events.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Event handling was always fairly simplistic since there were only
two events. With the addition of pin events this needed to be redesigned.
The state_change and lost_msgs events are now core events with the
guarantee that the last state is always available. The new pin events
are a queue of events (up to 64 for each event) and the oldest event
will be dropped if the application cannot keep up. Lost events are
marked with a new event flag.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Currently the transmit_(attempt_)done and received_msg functions set
the timestamp themselves. For the upcoming low-level pin API we need
to pass this as an argument instead. So make _ts variants that allow
the caller to specify the timestamp.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Kernel logging messes up the upcoming low-level CEC monitoring support
which is very time-sensitive. So change the debug level of this message
but keep a counter that is shown in the debugfs status log.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The transmit code would increase the sequence number first thing, even though
CEC_TRANSMIT would return an error due to a malformatted cec_msg struct later
on.
While valid behavior, this had the disadvantage of producing holes in the
sequence list that made debugging harder.
Only increase the sequence number when the whole message is validated.
When debugging (i.e. with cec-ctl -M) the sequence numbering is now nicely
increasing by 1 per message.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The CEC version, vendor ID and OSD name were not cleared when clearing the
current set of logical addresses. This was unexpected and somewhat confusing,
so reset all these fields to their default values. Also document this since
the documentation wasn't quite clear either.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Add a new capability CEC_CAP_NEEDS_HPD. If this capability is set
then the hardware can only use CEC if the HDMI Hotplug Detect pin
is high. Such hardware cannot handle the corner case in the CEC specification
where it is possible to transmit messages even if no hotplug signal is
present (needed for some displays that turn off the HPD when in standby,
but still have CEC enabled).
Typically hardware that needs this capability have the HPD wired to the CEC
block, often to a 'power' or 'active' pin.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
A simpler variant of cec_transmit_done to be used where the HW does
just a single attempt at a transmit. So if the status indicates an
error, then the corresponding error count will always be 1 and this
function figures that out based on the status argument.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
This function simplifies the integration of CEC in DRM drivers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
- use __func__ instead of writing the full function name
- drop debug message in cec_config_log_addr since the same information
will be reported later
- use debug level 1 for errors and infrequent events, use level 2 for
debugging CEC message traffic
- log when a transmit is retried, very useful to know when debugging
- debug messages now all start with lower case
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Just depend on DEBUG_FS, no need to invent a new kernel config.
Especially since CEC can be enabled by drm without enabling
MEDIA_SUPPORT.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Add an explicit config option to select whether the CEC remote control
messages are to be passed on to the RC subsystem or not.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Feature Abort shouldn't be sent in reply to messages from Unregistered,
since that would make it a broadcast message.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
When validating the struct cec_s_log_addrs input a debug message is printed
for all except two of the 'return -EINVAL' paths.
Also log the reason for the missing two paths.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Several error paths didn't log why an error was returned. Add this.
Also handle the corner case of "adapter is unconfigured AND the message
is from Unregistered to TV AND reply is non-zero" separately and return
EINVAL in that case, since it really is an invalid value and not an
unconfigured CEC device.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The hardcoded function name is actually wrong. Use __func__ instead.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The CEC specifications explicitly allows you to send poll messages and
Image/Text View On messages to a TV, even when unconfigured (i.e. there is
no hotplug signal detected). Some TVs will pull the HPD low when switching
to another input, or when going into standby, but CEC should still be
allowed to wake up such a display.
Add support for sending messages with initiator 0xf (Unregistered) and
destination 0 (TV) when no physical address is present.
This also required another change: the CEC adapter has to stay enabled as
long as 1) the CEC device is configured or 2) at least one filehandle is open
for the CEC device.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
When the adapter is unloaded or unconfigured, then all transmits and
pending waits should be flushed.
Move this code into its own function and improve the code that cancels
delayed work to avoid having to unlock adap->lock.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Poll messages that are used to allocate a logical address should
use the same initiator as the destination. Instead, it expected that
the initiator was 0xf which is not according to the standard.
This also had consequences for the message checks in cec_transmit_msg_fh
that incorrectly rejected poll messages with the same initiator and
destination.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Due to an incorrect condition the last_la used for the initial attempt at
claiming a logical address could be wrong.
The last_la wasn't converted to a mask when ANDing with type2mask, so that
test was broken.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
This race was discovered by running cec-compliance -A with the cec module debug
parameter set to 2: suddenly the test would fail.
It turns out that this happens when the test configures the adapter in
non-blocking mode, then it waits for the CEC_EVENT_STATE_CHANGE event and once
the event is received it unconfigures the adapter.
What happened was that the unconfigure was executed while the configure was
still transmitting the Report Features and Report Physical Address messages.
This messed up the internal state of the cec_adapter.
The fix is to transmit those messages with the adap->lock mutex held (this will
just queue them up in the internal transmit queue, and not actually transmit
anything yet). Only unlock the mutex once everything is done. The main thread
will dequeue the messages from the internal transmit queue and transmit them
one by one, unless an unconfigure was done, and in that case any messages are
just dropped.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
It's only a small function and this makes it easier to switch to
transmitting the message with adap->lock held in the next patch.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The fill function just fills in the cec_msg struct, it doesn't transmit
the message. This is now done explicitly.
This makes it possible to switch to transmitting this message with adap->lock
held.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
