| Age | Commit message (Collapse) | Author |
|---|
|
This patch adds meatadata capture support in vivid driver.
Adds new files for metadata capture.
Adds vivid controls to generate PTS and SCR for metadata stream.
also fixes v4l2-compliance issues seen on metadata device.
Signed-off-by: Vandana BN <bnvandana@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
When vbi stream is started, followed by video streaming,
the vid_cap_streaming and vid_out_streaming were not being set to true,
which would cause the video stream to stop when vbi stream is stopped.
This patch allows to set vid_cap_streaming and vid_out_streaming to true.
According to Hans Verkuil it appears that these 'if (dev->kthread_vid_cap)'
checks are a left-over from the original vivid development and should never
have been there.
Signed-off-by: Vandana BN <bnvandana@gmail.com>
Cc: <stable@vger.kernel.org> # for v3.18 and up
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Set/invalidate physical addresses based on the configuration of the
display present control. This is relevant not only when the display
present control is modified, but also when the Vivid instance EDID is
set/cleared.
Signed-off-by: Johan Korsnes <johan.korsnes@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Make the following properties per-input:
-Standard Signal Mode
-Standard
These properties need to be per-input in order to implement proper HDMI
(dis)connect-behavior, where the signal mode will be used to signify
whether or not there is an inpute device connected.
Signed-off-by: Johan Korsnes <johan.korsnes@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Make the following properties per-input
-DV Timings Signal Mode
-DV Timings
These properties need to be per-input in order to implement proper
HDMI (dis)connect-behavior, where the signal mode will be used to
signify whether or not there is an input device connected.
Signed-off-by: Johan Korsnes <johan.korsnes@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The tpf_min (1/100) and tpf_max (100/1) are used as the lowest and the
highest allowable value for the desired frame period in
vivid_vid_cap_s_parm().
But the comparison between these values is unnecessary because the compared
value is already chosen from webcam_intervals[] (from 1/60 to 1/1).
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
syzkaller reported crashes on kfree() called from
vivid_vid_cap_s_selection(). This looks like a simple typo, as
dev->bitmap_cap is allocated with vzalloc() throughout the file.
Fixes: ef834f7836ec0 ("[media] vivid: add the video capture and output
parts")
Signed-off-by: Alexander Potapenko <glider@google.com>
Reported-by: Syzbot <syzbot+6c0effb5877f6b0344e2@syzkaller.appspotmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
To correctly set the size of the image in a plane, it's needed
to divide the height of image by the vertical down sampling factor.
This was only happening in vivid_try_fmt_vid_cap(), but now it
applied in others sizeimage calculations as well.
Signed-off-by: André Almeida <andre.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Linux 4.20-rc7
* tag 'v4.20-rc7': (403 commits)
Linux 4.20-rc7
scripts/spdxcheck.py: always open files in binary mode
checkstack.pl: fix for aarch64
userfaultfd: check VM_MAYWRITE was set after verifying the uffd is registered
fs/iomap.c: get/put the page in iomap_page_create/release()
hugetlbfs: call VM_BUG_ON_PAGE earlier in free_huge_page()
memblock: annotate memblock_is_reserved() with __init_memblock
psi: fix reference to kernel commandline enable
arch/sh/include/asm/io.h: provide prototypes for PCI I/O mapping in asm/io.h
mm/sparse: add common helper to mark all memblocks present
mm: introduce common STRUCT_PAGE_MAX_SHIFT define
alpha: fix hang caused by the bootmem removal
XArray: Fix xa_alloc when id exceeds max
drm/vmwgfx: Protect from excessive execbuf kernel memory allocations v3
MAINTAINERS: Daniel for drm co-maintainer
drm/amdgpu: drop fclk/gfxclk ratio setting
IB/core: Fix oops in netdev_next_upper_dev_rcu()
dm thin: bump target version
drm/vmwgfx: remove redundant return ret statement
drm/i915: Flush GPU relocs harder for gen3
...
|
|
If start_streaming() fails and all queued buffers are returned to
vb2, then do not call v4l2_ctrl_request_complete(). Nothing happened
to the request and the state should remain as it was before
start_streaming was called.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
When vivid_update_format_cap() is called it should free any overlay
bitmap since the compose size will change.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: syzbot+0cc8e3cc63ca373722c6@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org> # for v3.18 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Now the equivalent of FRACT_CMP() is added in v4l2 common internal API
header.
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Now vidioc_cropcap is only used to return the pixelaspect, so
rename it accordingly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull new experimental media request API from Mauro Carvalho Chehab:
"A new media request API
This API is needed to support device drivers that can dynamically
change their parameters for each new frame. The latest versions of
Google camera and codec HAL depends on such feature.
At this stage, it supports only stateless codecs.
It has been discussed for a long time (at least over the last 3-4
years), and we finally reached to something that seem to work.
This series contain both the API and core changes required to support
it and a new m2m decoder driver (cedrus).
As the current API is still experimental, the only real driver using
it (cedrus) was added at staging[1]. We intend to keep it there for a
while, in order to test the API. Only when we're sure that this API
works for other cases (like encoders), we'll move this driver out of
staging and set the API into a stone.
[1] We added support for the vivid virtual driver (used only for
testing) to it too, as it makes easier to test the API for the ones
that don't have the cedrus hardware"
* tag 'media/v4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (53 commits)
media: dt-bindings: Document the Rockchip VPU bindings
media: platform: Add Cedrus VPU decoder driver
media: dt-bindings: media: Document bindings for the Cedrus VPU driver
media: v4l: Add definition for the Sunxi tiled NV12 format
media: v4l: Add definitions for MPEG-2 slice format and metadata
media: videobuf2-core: Rework and rename helper for request buffer count
media: v4l2-ctrls.c: initialize an error return code with zero
media: v4l2-compat-ioctl32.c: add missing documentation for a field
media: media-request: update documentation
media: media-request: EPERM -> EACCES/EBUSY
media: v4l2-ctrls: improve media_request_(un)lock_for_update
media: v4l2-ctrls: use media_request_(un)lock_for_access
media: media-request: add media_request_(un)lock_for_access
media: vb2: set reqbufs/create_bufs capabilities
media: videodev2.h: add new capabilities for buffer types
media: buffer.rst: only set V4L2_BUF_FLAG_REQUEST_FD for QBUF
media: v4l2-ctrls: return -EACCES if request wasn't completed
media: media-request: return -EINVAL for invalid request_fds
media: vivid: add request support
media: vivid: add mc
...
|
|
Support 640x480 as a frame size for video input devices of vivid.
Signed-off-by: Keiichi Watanabe <keiichiw@chromium.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Several CEC functions are actually specific for use with receivers,
i.e. they should be part of the V4L2 subsystem, not CEC.
These functions deal with validating and modifying EDIDs for (HDMI)
receivers, and they do not actually have anything to do with the CEC
subsystem and whether or not CEC is enabled. The problem was that if
the CEC_CORE config option was not set, then these functions would
become stubs, but that's not right: they should always be valid.
So replace the cec_ prefix by v4l2_ and move them to v4l2-dv-timings.c.
Update all drivers that call these accordingly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <stable@vger.kernel.org> # for v4.17 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The implementation of strscpy() is more robust and safer.
That's now the recommended way to copy NUL terminated strings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Add support for requests to vivid.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
An older version of the driver patches were merged accidentally which
resulted in missing the array_size parameter that tells the length of the
array that contains the different supported sizes.
Bring it back to v4l2_find_nearest size and make the corresponding change
for the drivers using it as well.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Use v4l2_find_nearest_size instead of a driver specific function to find
nearest matching size.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Replace the old license information with the corresponding SPDX
license.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
This struct is there just two store two arguments of
v4l2_find_nearest_format(). The other two arguments are passed
as parameter.
IMHO, there isn't much sense on doing that, and that will just
add one more struct to document ;)
So, let's get rid of the struct, passing the parameters directly.
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
vivid_try_fmt_vid_cap() called tpg_calc_line_width to calculate the sizeimage
value, but that tpg function uses the current format, not the proposed (tried)
format.
Rewrote this code to calculate this correctly.
The vivid_try_fmt_vid_out() code was completely wrong w.r.t. sizeimage, and
neither did it take the vdownsampling[] factors into account.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Vincent Abriou <vincent.abriou@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Add 3840x2160 as valid resolution for the webcam capture input and
adjust the webcam intervals accordingly.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Support HSV encoding. Most of the logic is replicated from ycbcr_enc.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
g/s_selection
Returning -EINVAL indicates wrong arguments, but that's not the case
here.
Returning -ENOTTY is also no option, since the ioctl is implemented, but
it just is not valid for this input.
So use -ENODATA instead. This is also used elsewhere when an ioctl isn't
valid for a specific input.
In this case G/S_SELECTION returned -EINVAL for the webcam input. That
input doesn't support cropping, instead it uses ENUM_FRAMESIZES to
enumerate a list of discrete frame sizes.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The vivid driver didn't set the V4L2_CAP_TIMEPERFRAME flag in s_parm for the
non-webcam inputs. This caused a v4l2-compliance fail.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
* topic/cec:
[media] DocBook/media: add CEC documentation
[media] s5p_cec: get rid of an unused var
[media] move s5p-cec to staging
[media] vivid: add CEC emulation
[media] cec: s5p-cec: Add s5p-cec driver
[media] cec: adv7511: add cec support
[media] cec: adv7842: add cec support
[media] cec: adv7604: add cec support
[media] cec: add compat32 ioctl support
[media] cec/TODO: add TODO file so we know why this is still in staging
[media] cec: add HDMI CEC framework (api)
[media] cec: add HDMI CEC framework (adapter)
[media] cec: add HDMI CEC framework (core)
[media] cec-funcs.h: static inlines to pack/unpack CEC messages
[media] cec.h: add cec header
[media] cec-edid: add module for EDID CEC helper functions
[media] cec.txt: add CEC framework documentation
[media] rc: Add HDMI CEC protocol handling
|
|
Make this a proper typed array. Drop the old allocate context code since
that is no longer used.
Note that the memops functions now get a struct device pointer instead of
the struct device ** that was there initially (actually a void pointer to
a struct containing only a struct device pointer).
This code is now a lot cleaner.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The vivid driver has been extended to provide CEC adapters for the HDMI
input and HDMI outputs in order to test CEC applications.
This CEC emulation is faithful to the CEC timings (i.e., it all at a
snail's pace).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Gcc 6.1 warns about some unused vars. Remove them:
drivers/media/platform/vivid/vivid-vid-cap.c:40:2: warning: 'tpf_default' defined but not used [-Wunused-const-variable=]
tpf_default = {.numerator = 1, .denominator = 30};
^~~~~~~~~~~
drivers/media/platform/vivid/vivid-sdr-cap.c:54:27: warning: 'NUM_FORMATS' defined but not used [-Wunused-const-variable=]
static const unsigned int NUM_FORMATS = ARRAY_SIZE(formats);
^~~~~~~~~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The v4l2_rect helper functions have been moved to
include/media/v4l2-rect.h. Use this new header, dropping the functions
from vivid.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The queue_setup callback has a void pointer that is just for V4L2
and is the pointer to the v4l2_format struct that was passed to
VIDIOC_CREATE_BUFS. The idea was that drivers would use the information
from that struct to buffers suitable for the requested format.
After the vb2 split series this pointer is now a void pointer,
which is ugly, and the reality is that all existing drivers will
effectively just look at the sizeimage field of v4l2_format.
To make this more generic the queue_setup callback is changed:
the void pointer is dropped, instead if the *num_planes argument
is 0, then use the current format size, if it is non-zero, then
it contains the number of requested planes and the sizes array
contains the requested sizes. If either is unsupported, then return
-EINVAL, otherwise use the requested size(s).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Add the new match_reduced_fps argument to v4l2_match_dv_timings().
Depending on the situation you may or may not desire to match the
reduced_fps flag. Typically only HDMI transmitters will need to
check for this flag.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
With this patch, vivid capture thread can now generate a video with
frame rate reduced by a factor of 1000 / 1001. This option can be
selected using a control Reduced Framerate from gui.
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Replace struct v4l2_format * with void * to make queue_setup()
for common use.
And then, modify all device drivers related with this change.
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: fix missing const in fimc-lite.c]
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Remove v4l2 stuff - v4l2_buf, v4l2_plane - from struct vb2_buffer.
Add new member variables - bytesused, length, offset, userptr, fd,
data_offset - to struct vb2_plane in order to cover all information
of v4l2_plane.
struct vb2_plane {
<snip>
unsigned int bytesused;
unsigned int length;
union {
unsigned int offset;
unsigned long userptr;
int fd;
} m;
unsigned int data_offset;
}
Replace v4l2_buf with new member variables - index, type, memory - which
are common fields for buffer management.
struct vb2_buffer {
<snip>
unsigned int index;
unsigned int type;
unsigned int memory;
unsigned int num_planes;
struct vb2_plane planes[VIDEO_MAX_PLANES];
<snip>
};
v4l2 specific fields - flags, field, timestamp, timecode,
sequence - are moved to vb2_v4l2_buffer in videobuf2-v4l2.c
struct vb2_v4l2_buffer {
struct vb2_buffer vb2_buf;
__u32 flags;
__u32 field;
struct timeval timestamp;
struct v4l2_timecode timecode;
__u32 sequence;
};
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Added support for reduced blanking version 2 (RB v2) in cvt timings.
Standard specifies a fixed vsync pulse of 8 lines to indicate RB v2
timings. Vertical back porch is fixed at 6 lines and vertical front
porch is remainder of vertical blanking time.
For RB v2, horizontal blanking is fixed at 80 pixels. Horizontal sync
is fixed at 32. All horizontal timing counts (active pixels, front,
back porches) can be specified upto a precision of 1.
RB v2 allows for non standard aspect ratios. In RB v2 vsync does not
indicate aspect ratio. In absence of aspect ratio v4l2_detect_cvt()
cannot calculate image width from image height. Hence extending the
v4l2_detect_cvt() to pass image width in case of RB v2.
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The detect_cvt/gtf() now supports timing calculations for interlaced
format.
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Extend detect_cvt/gtf API to indicate the format type (interlaced
or progressive). In case of interlaced, the vertical front and back
porch and vsync values for both (odd,even) fields are considered to
derive image height. Populated vsync, vertical front, back porch
values in bt timing structure for even and odd fields and updated
the flags appropriately.
Also modified the functions calling the detect_cvt/gtf(). As of now
these functions are calling detect_cvt/gtf() with interlaced flag
set to false.
Cc: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Add support for the transfer function: create a new control for it,
and support it for both capture and output sides.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The format description is now filled in by the core, so we can
drop this in this virtual driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Use the VIVID_WEBCAM_SIZES constant where appropriate and add a
1920x1080 pixel frame size setting with frame rates of 2 fps and
5 fps.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Don't rely on V4L2_DV_BT_STD_CEA861 since that include the
640x480p format, which is an IT format, not CE.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
In addition to v4l2_find_dv_timings_cap(), where timings are searched
against the list of preset timings, the incoming timing from v4l2-ctl
is checked against CVT and GTF standards. If it confirms to be CVT or
GTF, it is treated as valid timing and vivid format is updated with
new timings.
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The vivid driver reports a range of frame intervals for non-webcams, when in fact
the frame interval is fixed for those inputs as it depends on the DV timings or
standard. Just report the single discrete frame interval instead.
Caught by v4l2-compliance.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Allow setting the same timings as the current timings (i.e., do nothing in that
case). The code was actually there, but the vb2_is_busy() call was done before
the timings check instead of afterwards.
Found by v4l2-compliance.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Make vivid aware of the difference of planes and buffers. Note that
this does not yet add support for hor/vert downsampled formats.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
These fields are necessary to handle the new planar formats.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The successive TOP/BOTTOM fields did not move as they should: only
every other field actually changed position.
The cause was that the tpg needs to know if it is dealing with a
FIELD_ALTERNATE case since that requires slightly different handling.
So tell the TPG whether or not the field setting is for the ALTERNATE
case or not.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
